Abstract: This paper presents the results of an experimental study on the performance of a triboelectric separator of plastic mixtures used for recycling. The separator consists of four cylindrical electrodes. The principle behind the separation technique is based on the difference in the Coulomb force acting on the plastic particles after triboelectric charging. The separation of mixtures of acrylonitrile butadiene styrene (ABS) and polystyrene (PS) using this method was studied. The effects of the triboelectric charging time and applied voltage on the separation efficiency were investigated. The experimental results confirm that it is possible to obtain a high purity and recovery rate for the initial compositions considered in this study.
Abstract: This paper deals with a power-conscious ANDEXOR- Inverter type logic implementation for a complex class of Boolean functions, namely Achilles- heel functions. Different variants of the above function class have been considered viz. positive, negative and pure horn for analysis and simulation purposes. The proposed realization is compared with the decomposed implementation corresponding to an existing standard AND-EXOR logic minimizer; both result in Boolean networks with good testability attribute. It could be noted that an AND-OR-EXOR type logic network does not exist for the positive phase of this unique class of logic function. Experimental results report significant savings in all the power consumption components for designs based on standard cells pertaining to a 130nm UMC CMOS process The simulations have been extended to validate the savings across all three library corners (typical, best and worst case specifications).
Abstract: This paper addresses modeling and optimization of process parameters in powder mixed electrical discharge machining (PMEDM). The process output characteristics include metal removal rate (MRR) and electrode wear rate (EWR). Grain size of Aluminum powder (S), concentration of the powder (C), discharge current (I) pulse on time (T) are chosen as control variables to study the process performance. The experimental results are used to develop the regression models based on second order polynomial equations for the different process characteristics. Then, a genetic algorithm (GA) has been employed to determine optimal process parameters for any desired output values of machining characteristics.
Abstract: This paper deals with analysis of flexural stiffness,
indentation and their energies in three point loading of sandwich
beams with composite faces from Eglass/epoxy and cores from
Polyurethane or PVC. Energy is consumed in three stages of
indentation in laminated beam, indentation of sandwich beam and
bending of sandwich beam. Theory of elasticity is chosen to present
equations for indentation of laminated beam, then these equations
have been corrected to offer better results. An analytical model has
been used assuming an elastic-perfectly plastic compressive behavior
of the foam core. Classical theory of beam is used to describe three
point bending. Finite element (FE) analysis of static indentation
sandwich beams is performed using the FE code ABAQUS. The
foam core is modeled using the crushable foam material model and
response of the foam core is experimentally characterized in uniaxial
compression.
Three point bending and indentation have been done
experimentally in two cases of low velocity and higher velocity
(quasi-impact) of loading. Results can describe response of beam in
terms of core and faces thicknesses, core material, indentor diameter,
energy absorbed, and length of plastic area in the testing. The
experimental results are in good agreement with the analytical and
FE analyses. These results can be used as an introduction for impact
loading and energy absorbing of sandwich structures.
Abstract: In a wind power generator using doubly fed induction
generator (DFIG), the three-phase pulse width modulation (PWM)
voltage source converter (VSC) is used as grid side converter (GSC)
and rotor side converter (RSC). The standard linear control laws
proposed for GSC provides not only instablity against comparatively
large-signal disturbances, but also the problem of stability due to
uncertainty of load and variations in parameters. In this paper, a
nonlinear controller is designed for grid side converter (GSC) of a
DFIG for wind power application. The nonlinear controller is
designed based on the input-output feedback linearization control
method. The resulting closed-loop system ensures a sufficient
stability region, make robust to variations in circuit parameters and
also exhibits good transient response. Computer simulations and
experimental results are presented to confirm the effectiveness of the
proposed control strategy.
Abstract: This research was conducted to develop a correlation
between microstructure of HSLA steel and the mechanical properties
that occur as a result of both laser and mechanical forming processes
of the metal. The technique of forming flat metals by applying laser
beams is a relatively new concept in the manufacturing industry.
However, the effects of laser energy on the stability of metal alloy
phases have not yet been elucidated in terms of phase
transformations and microhardness. In this work, CO2 laser source
was used to irradiate the surface of a flat metal then the
microstructure and microhardness of the metal were studied on the
formed specimen. The extent to which the microstructure changed
depended on the heat inputs of up to 1000 J/cm2 with cooling rates of
about 4.8E+02 K/s. Experimental results revealed that the irradiated
surface of a HSLA steel had transformed to austenitic structure
during the heating process.
Abstract: The k-nearest neighbors (knn) is a simple but effective method of classification. In this paper we present an extended version of this technique for chemical compounds used in High Throughput Screening, where the distances of the nearest neighbors can be taken into account. Our algorithm uses kernel weight functions as guidance for the process of defining activity in screening data. Proposed kernel weight function aims to combine properties of graphical structure and molecule descriptors of screening compounds. We apply the modified knn method on several experimental data from biological screens. The experimental results confirm the effectiveness of the proposed method.
Abstract: In this paper, a novel feature-based image
watermarking scheme is proposed. Zernike moments which have
invariance properties are adopted in the scheme. In the proposed
scheme, feature points are first extracted from host image and several
circular patches centered on these points are generated. The patches
are used as carriers of watermark information because they can be
regenerated to locate watermark embedding positions even when
watermarked images are severely distorted. Zernike transform is then
applied to the patches to calculate local Zernike moments. Dither
modulation is adopted to quantize the magnitudes of the Zernike
moments followed by false alarm analysis. Experimental results show
that quality degradation of watermarked image is visually
transparent. The proposed scheme is very robust against image
processing operations and geometric attacks.
Abstract: Recently, there have been considerable efforts towards the convergence between P2P and Grid computing in order to reach a solution that takes the best of both worlds by exploiting the advantages that each offers. Augmenting the peer-to-peer model to the services of the Grid promises to eliminate bottlenecks and ensure greater scalability, availability, and fault-tolerance. The Grid Information Service (GIS) directly influences quality of service for grid platforms. Most of the proposed solutions for decentralizing the GIS are based on completely flat overlays. The main contributions for this paper are: the investigation of a novel resource discovery framework for Grid implementations based on a hierarchy of structured peer-to-peer overlay networks, and introducing a discovery algorithm utilizing the proposed framework. Validation of the framework-s performance is done via simulation. Experimental results show that the proposed organization has the advantage of being scalable while providing fault-isolation, effective bandwidth utilization, and hierarchical access control. In addition, it will lead to a reliable, guaranteed sub-linear search which returns results within a bounded interval of time and with a smaller amount of generated traffic within each domain.
Abstract: Steel surface defect detection is essentially one of
pattern recognition problems. Support Vector Machines (SVMs) are
known as one of the most proper classifiers in this application. In this
paper, we introduce a more accurate classification method by using
SVMs as our final classifier of the inspection system. In this scheme,
multiclass classification task is performed based on the "one-againstone"
method and different kernels are utilized for each pair of the
classes in multiclass classification of the different defects.
In the proposed system, a decision tree is employed in the first
stage for two-class classification of the steel surfaces to "defect" and
"non-defect", in order to decrease the time complexity. Based on
the experimental results, generated from over one thousand images,
the proposed multiclass classification scheme is more accurate than
the conventional methods and the overall system yields a sufficient
performance which can meet the requirements in steel manufacturing.
Abstract: commercially produced in Malaysia granular
palm shell activated carbon (PSAC) was biomodified with
bacterial biomass (Bacillus subtilis) to produce a hybrid
biosorbent of higher efficiency. The obtained biosorbent was
evaluated in terms of adsorption capacity to remove copper
and zinc metal ions from aqueous solutions. The adsorption
capacity was evaluated in batch adsorption experiments where
concentrations of metal ions varied from 20 to 350 mg/L. A
range of pH from 3 to 6 of aqueous solutions containing metal
ions was tested. Langmuir adsorption model was used to
interpret the experimental data. Comparison of the adsorption
data of the biomodified and original palm shell activated
carbon showed higher uptake of metal ions by the hybrid
biosorbent. A trend in metal ions uptake increase with the
increase in the solution-s pH was observed. The surface
characterization data indicated a decrease in the total surface
area for the hybrid biosorbent; however the uptake of copper
and zinc by it was at least equal to the original PSAC at pH 4
and 5. The highest capacity of the hybrid biosorbent was
observed at pH 5 and comprised 22 mg/g and 19 mg/g for
copper and zinc, respectively. The adsorption capacity at the
lowest pH of 3 was significantly low. The experimental results
facilitated identification of potential factors influencing the
adsorption of copper and zinc onto biomodified and original
palm shell activated carbon.
Abstract: Square pipes (pipes with square cross sections) are
being used for various industrial objectives, such as machine
structure components and housing/building elements. The utilization
of them is extending rapidly and widely. Hence, the out-put of those
pipes is increasing and new application fields are continually
developing.
Due to various demands in recent time, the products have to
satisfy difficult specifications with high accuracy in dimensions. The
reshaping process design of pipes with square cross sections;
however, is performed by trial and error and based on expert-s
experience.
In this paper, a computer-aided simulation is developed based on
the 2-D elastic-plastic method with consideration of the shear
deformation to analyze the reshaping process. Effect of various
parameters such as diameter of the circular pipe and mechanical
properties of metal on product dimension and quality can be
evaluated by using this simulation. Moreover, design of reshaping
process include determination of shrinkage of cross section,
necessary number of stands, radius of rolls and height of pipe at each
stand, are investigated. Further, it is shown that there are good
agreements between the results of the design method and the
experimental results.
Abstract: Text categorization is the problem of classifying text
documents into a set of predefined classes. In this paper, we
investigated three approaches to build a meta-classifier in order to
increase the classification accuracy. The basic idea is to learn a metaclassifier
to optimally select the best component classifier for each
data point. The experimental results show that combining classifiers
can significantly improve the accuracy of classification and that our
meta-classification strategy gives better results than each individual
classifier. For 7083 Reuters text documents we obtained a
classification accuracies up to 92.04%.
Abstract: Conventionally the selection of parameters depends
intensely on the operator-s experience or conservative technological
data provided by the EDM equipment manufacturers that assign
inconsistent machining performance. The parameter settings given by
the manufacturers are only relevant with common steel grades. A
single parameter change influences the process in a complex way.
Hence, the present research proposes artificial neural network (ANN)
models for the prediction of surface roughness on first commenced
Ti-15-3 alloy in electrical discharge machining (EDM) process. The
proposed models use peak current, pulse on time, pulse off time and
servo voltage as input parameters. Multilayer perceptron (MLP) with
three hidden layer feedforward networks are applied. An assessment
is carried out with the models of distinct hidden layer. Training of the
models is performed with data from an extensive series of
experiments utilizing copper electrode as positive polarity. The
predictions based on the above developed models have been verified
with another set of experiments and are found to be in good
agreement with the experimental results. Beside this they can be
exercised as precious tools for the process planning for EDM.
Abstract: In this paper, an improved ant colony optimization
(ACO) algorithm is proposed to enhance the performance of global
optimum search. The strategy of the proposed algorithm has the
capability of fuzzy pheromone updating, adaptive parameter tuning,
and mechanism resetting. The proposed method is utilized to tune the
parameters of the fuzzy controller for a real beam and ball system.
Simulation and experimental results indicate that better performance
can be achieved compared to the conventional ACO algorithms in the
aspect of convergence speed and accuracy.
Abstract: Digital watermarking has become an important technique for copyright protection but its robustness against attacks remains a major problem. In this paper, we propose a normalizationbased robust image watermarking scheme. In the proposed scheme, original host image is first normalized to a standard form. Zernike transform is then applied to the normalized image to calculate Zernike moments. Dither modulation is adopted to quantize the magnitudes of Zernike moments according to the watermark bit stream. The watermark extracting method is a blind method. Security analysis and false alarm analysis are then performed. The quality degradation of watermarked image caused by the embedded watermark is visually transparent. Experimental results show that the proposed scheme has very high robustness against various image processing operations and geometric attacks.
Abstract: In this paper we address the problem of musical style
classification, which has a number of applications like indexing in
musical databases or automatic composition systems. Starting from
MIDI files of real-world improvisations, we extract the melody track
and cut it into overlapping segments of equal length. From these
fragments, some numerical features are extracted as descriptors of
style samples. We show that a standard Bayesian classifier can be
conveniently employed to build an effective musical style classifier,
once this set of features has been extracted from musical data.
Preliminary experimental results show the effectiveness of the
developed classifier that represents the first component of a musical
audio retrieval system
Abstract: Recently, information security has become a key issue
in information technology as the number of computer security
breaches are exposed to an increasing number of security threats. A
variety of intrusion detection systems (IDS) have been employed for
protecting computers and networks from malicious network-based or
host-based attacks by using traditional statistical methods to new data
mining approaches in last decades. However, today's commercially
available intrusion detection systems are signature-based that are not
capable of detecting unknown attacks. In this paper, we present a
new learning algorithm for anomaly based network intrusion
detection system using decision tree algorithm that distinguishes
attacks from normal behaviors and identifies different types of
intrusions. Experimental results on the KDD99 benchmark network
intrusion detection dataset demonstrate that the proposed learning
algorithm achieved 98% detection rate (DR) in comparison with
other existing methods.
Abstract: Heat pipes are used to control the thermal problem for
electronic cooling. It is especially difficult to dissipate heat to a heat
sink in an environment in space compared to earth. For solving this
problem, in this study, the Poiseuille (Po) number, which is the main
measure of the performance of a heat pipe, is studied by CFD; then, the
heat pipe performance is verified with experimental results. A heat
pipe is then fabricated for a spatial environment, and an in-house code
is developed. Further, a heat pipe subsystem, which consists of a heat
pipe, MLI (Multi Layer Insulator), SSM (Second Surface Mirror), and
radiator, is tested and correlated with the TMM (Thermal
Mathematical Model) through a commercial code. The correlation
results satisfy the 3K requirement, and the generated thermal model is
verified for application to a spatial environment.
Abstract: Many agricultural and especially greenhouse
applications like plant inspection, data gathering, spraying and
selective harvesting could be performed by robots. In this paper
multiple nonholonomic robots are used in order to create a desired
formation scheme for screening solar energy in a greenhouse through
data gathering. The formation consists from a leader and a team
member equipped with appropriate sensors. Each robot is dedicated
to its mission in the greenhouse that is predefined by the
requirements of the application. The feasibility of the proposed
application includes experimental results with three unmanned
ground vehicles (UGV).