Abstract: In the context of sensor networks, where every few
dB saving counts, the novel node cooperation schemes are reviewed
where MIMO techniques play a leading role. These methods could be
treated as joint approach for designing physical layer of their
communication scenarios. Then we analyzed the BER performance
of transmission diversity schemes under a general fading channel
model and proposed a power allocation strategy to the transmitting
sensor nodes. This approach is then compared to an equal-power
assignment method and its performance enhancement is verified by
the simulation. Another key point of the contribution lies in the
combination of optimal power allocation and sensor nodes-
cooperation in a transmission diversity regime (MISO). Numerical
results are given through figures to demonstrate the optimality and
efficiency of proposed combined approach.
Abstract: In this paper, a generalized synchronization scheme, which is called function synchronization, for chaotic systems is studied. Based on Lyapunov method and active control method, we design the synchronization controller for the system such that the error dynamics between master and slave chaotic systems is asymptotically stable. For verification of our theory, computer and circuit simulations for a specific chaotic system is conducted.
Abstract: The development and extension of large cities induced
a need for shallow tunnel in soft ground of building areas. Estimation
of ground settlement caused by the tunnel excavation is important
engineering point. In this paper, prediction of surface subsidence
caused by tunneling in one section of seventh line of Tehran subway
is considered. On the basis of studied geotechnical conditions of the
region, tunnel with the length of 26.9km has been excavated applying
a mechanized method using an EPB-TBM with a diameter of 9.14m.
In this regard, settlement is estimated utilizing both analytical and
numerical finite element method. The numerical method shows that
the value of settlement in this section is 5cm. Besides, the analytical
consequences (Bobet and Loganathan-Polous) are 5.29 and 12.36cm,
respectively. According to results of this study, due tosaturation of
this section, there are good agreement between Bobet and numerical
methods. Therefore, tunneling processes in this section needs a
special consolidation measurement and support system before the
passage of tunnel boring machine.
Abstract: Coated tool inserts can be considered as the backbone
of machining processes due to their wear and heat resistance.
However, defects of coating can degrade the integrity of these inserts
and the number of these defects should be minimized or eliminated if
possible. Recently, the advancement of coating processes and
analytical tools open a new era for optimizing the coating tools.
First, an overview is given regarding coating technology for cutting
tool inserts. Testing techniques for coating layers properties, as well
as the various coating defects and their assessment are also surveyed.
Second, it is introduced an experimental approach to examine the
possible coating defects and flaws of worn multicoated carbide
inserts using two important techniques namely scanning electron
microscopy and atomic force microscopy. Finally, it is
recommended a simple procedure for investigating manufacturing
defects and flaws of worn inserts.
Abstract: Nowadays, people are going more and more mobile, both in terms of devices and associated applications. Moreover, services that these devices are offering are getting wider and much more complex. Even though actual handheld devices have considerable computing power, their contexts of utilization are different. These contexts are affected by the availability of connection, high latency of wireless networks, battery life, size of the screen, on-screen or hard keyboard, etc. Consequently, development of mobile applications and their associated mobile Web services, if any, should follow a concise methodology so they will provide a high Quality of Service. The aim of this paper is to highlight and discuss main issues to consider when developing mobile applications and mobile Web services and then propose a framework that leads developers through different steps and modules toward development of efficient and secure mobile applications. First, different challenges in developing such applications are elicited and deeply discussed. Second, a development framework is presented with different modules addressing each of these challenges. Third, the paper presents an example of a mobile application, Eivom Cinema Guide, which benefits from following our development framework.
Abstract: This paper presents a formant-tracking linear prediction
(FTLP) model for speech processing in noise. The main focus of this
work is the detection of formant trajectory based on Hidden Markov
Models (HMM), for improved formant estimation in noise. The
approach proposed in this paper provides a systematic framework for
modelling and utilization of a time- sequence of peaks which satisfies
continuity constraints on parameter; the within peaks are modelled
by the LP parameters. The formant tracking LP model estimation
is composed of three stages: (1) a pre-cleaning multi-band spectral
subtraction stage to reduce the effect of residue noise on formants
(2) estimation stage where an initial estimate of the LP model of
speech for each frame is obtained (3) a formant classification using
probability models of formants and Viterbi-decoders. The evaluation
results for the estimation of the formant tracking LP model tested
in Gaussian white noise background, demonstrate that the proposed
combination of the initial noise reduction stage with formant tracking
and LPC variable order analysis, results in a significant reduction in
errors and distortions. The performance was evaluated with noisy
natual vowels extracted from international french and English vocabulary
speech signals at SNR value of 10dB. In each case, the
estimated formants are compared to reference formants.
Abstract: The need to evaluate and understand the natural
drainage pattern in a flood prone, and fast developing environment is
of paramount importance. This information will go a long way to
help the town planners to determine the drainage pattern, road
networks and areas where prominent structures are to be located. This
research work was carried out with the aim of studying the Bayelsa
landscape topography using digitized topographic information, and to
model the natural drainage flow pattern that will aid the
understanding and constructions of workable drainages. To achieve
this, digitize information of elevation and coordinate points were
extracted from a global imagery map. The extracted information was
modeled into 3D surfaces. The result revealed that the average
elevation for Bayelsa State is 12 m above sea level. The highest
elevation is 28 m, and the lowest elevation 0 m, along the coastline.
In Yenagoa the capital city of Bayelsa were a detail survey was
carried out showed that average elevation is 15 m, the highest
elevation is 25 m and lowest is 3 m above the mean sea level. The
regional elevation in Bayelsa, showed a gradation decrease from the
North Eastern zone to the South Western Zone. Yenagoa showed an
observed elevation lineament, were low depression is flanked by high
elevation that runs from the North East to the South west. Hence,
future drainages in Yenagoa should be directed from the high
elevation, from South East toward the North West and from the
North West toward South East, to the point of convergence which is
at the center that flows from South East toward the North West.
Bayelsa when considered on a regional Scale, the flow pattern is from
the North East to the South West, and also North South. It is
recommended that in the event of any large drainage construction at
municipal scale, it should be directed from North East to the South
West or from North to South. Secondly, detail survey should be
carried out to ascertain the local topography and the drainage pattern
before the design and construction of any drainage system in any part
of Bayelsa.
Abstract: This paper presents a design and prototype
implementation of new home automation system that uses WiFi
technology as a network infrastructure connecting its parts. The
proposed system consists of two main components; the first part is
the server (web server), which presents system core that manages,
controls, and monitors users- home. Users and system administrator
can locally (LAN) or remotely (internet) manage and control system
code. Second part is hardware interface module, which provides
appropriate interface to sensors and actuator of home automation
system. Unlike most of available home automation system in the
market the proposed system is scalable that one server can manage
many hardware interface modules as long as it exists on WiFi
network coverage. System supports a wide range of home
automation devices like power management components, and
security components. The proposed system is better from the
scalability and flexibility point of view than the commercially
available home automation systems.
Abstract: Plastic waste is a big issue in Thailand, but the amount of recycled plastic in Thailand is still low due to the high investment and operating cost. Hence, the rest of plastic waste are burnt to destroy or sent to the landfills. In order to be financial viable, an effective reverse logistics infrastructure is required to support the product recovery activities. However, there is a conflict between reducing the cost and raising environmental protection level. The purpose of this study is to build a goal programming (GP) so that it can be used to help analyze the proper planning of the Thailand-s plastic recycling system that involves multiple objectives. This study considers three objectives; reducing total cost, increasing the amount of plastic recovery, and raising the desired plastic materials in recycling process. The results from two priority structures show that it is necessary to raise the total cost budget in order to achieve targets on amount of recycled plastic and desired plastic materials.
Abstract: This paper proposes a method of adaptively generating a gait pattern of biped robot. The gait synthesis is based on human's gait pattern analysis. The proposed method can easily be applied to generate the natural and stable gait pattern of any biped robot. To analyze the human's gait pattern, sequential images of the human's gait on the sagittal plane are acquired from which the gait control values are extracted. The gait pattern of biped robot on the sagittal plane is adaptively generated by a genetic algorithm using the human's gait control values. However, gait trajectories of the biped robot on the sagittal plane are not enough to construct the complete gait pattern because the biped robot moves on 3-dimension space. Therefore, the gait pattern on the frontal plane, generated from Zero Moment Point (ZMP), is added to the gait one acquired on the sagittal plane. Consequently, the natural and stable walking pattern for the biped robot is obtained.
Abstract: In this paper we consider the issue of distributed adaptive estimation over sensor networks. To deal with more realistic scenario, different variance for observation noise is assumed for sensors in the network. To solve the problem of different variance of observation noise, the proposed method is divided into two phases: I) Estimating each sensor-s observation noise variance and II) using the estimated variances to obtain the desired parameter. Our proposed algorithm is based on a diffusion least mean square (LMS) implementation with linear combiner model. In the proposed algorithm, the step-size parameter the coefficients of linear combiner are adjusted according to estimated observation noise variances. As the simulation results show, the proposed algorithm considerably improves the diffusion LMS algorithm given in literature.
Abstract: The Bangalore City is facing the acute problem of
pollution in the atmosphere due to the heavy increase in the traffic
and developmental activities in recent years. The present study is an
attempt in the direction to assess trend of the ambient air quality
status of three stations, viz., AMCO Batteries Factory, Mysore Road,
GRAPHITE INDIA FACTORY, KHB Industrial Area, Whitefield
and Ananda Rao Circle, Gandhinagar with respect to some of the
major criteria pollutants such as Total Suspended particular matter
(SPM), Oxides of nitrogen (NOx), and Oxides of sulphur (SO2). The
sites are representative of various kinds of growths viz., commercial,
residential and industrial, prevailing in Bangalore, which are
contributing to air pollution. The concentration of Sulphur Dioxide
(SO2) at all locations showed a falling trend due to use of refined
petrol and diesel in the recent years. The concentration of Oxides of
nitrogen (NOx) showed an increasing trend but was within the
permissible limits. The concentration of the Suspended particular
matter (SPM) showed the mixed trend. The correlation between
model and observed values is found to vary from 0.4 to 0.7 for SO2,
0.45 to 0.65 for NOx and 0.4 to 0.6 for SPM. About 80% of data is
observed to fall within the error band of ±50%. Forecast test for the
best fit models showed the same trend as actual values in most of the
cases. However, the deviation observed in few cases could be
attributed to change in quality of petro products, increase in the
volume of traffic, introduction of LPG as fuel in many types of
automobiles, poor condition of roads, prevailing meteorological
conditions, etc.
Abstract: In this paper we analyze the core issues affecting
software architecture in enterprise projects where a large number of
people at different backgrounds are involved and complex business,
management and technical problems exist. We first give general
features of typical enterprise projects and then present foundations of
software architectures. The detailed analysis of core issues affecting
software architecture in software development phases is given. We
focus on three main areas in each development phase: people,
process, and management related issues, structural (product) issues,
and technology related issues. After we point out core issues and
problems in these main areas, we give recommendations for
designing good architecture. We observed these core issues and the
importance of following the best software development practices and
also developed some novel practices in many big enterprise
commercial and military projects in about 10 years of experience.
Abstract: This is a survey research using quantitative and qualitative methodology. There were three objectives: 1) To study participatory level of community in water and waste environment management. 2) To study the affecting factors for community participation in water and waste environment management in Ampawa District, Samut Songkram Province. 3) To search for the participatory patterns in water and waste management. The population sample for the quantitative research was 1,364 people living in Ampawa District. The methodology was simple random sampling. Research instrument was a questionnaire and the qualitative research used purposive sampling in 6 Sub Districts which are Ta Ka, Suanluang, Bangkae, Muangmai, Kwae-om, and Bangnanglee Sub District Administration Organization. Total population is 63. For data analysis, the study used content analysis from quantitative research to synthesize and build question frame from the content for interview and conducting focus group interview. The study found that the community participatory in the issue of level in water and waste management are moderate of planning, operation, and evaluation. The issue of being beneficial is at low level. Therefore, the overall participatory level of community in water and waste environment management is at a medium level. The factors affecting the participatory of community in water and waste management are age, the period dwelling in the community and membership in which the mean difference is statistic significant at 0.05 in area of operation, being beneficial, and evaluation. For patterns of community participation, there is the correlation with water and waste management in 4 concerns which are 1) Participation in planning 2) Participation in operation 3) Participation in being beneficial both directly and indirectly benefited 4) Participation in evaluation and monitoring. The recommendation from this study is the need to create conscious awareness in order to increase participation level of people by organizing activities that promote participation with volunteer spirit. Government should open opportunities for people to participate in sharing ideas and create the culture of living together with equality which would build more concrete participation.
Abstract: Mobile IPv6 (MIPv6) describes how mobile node can change its point of attachment from one access router to another. As a demand for wireless mobile devices increases, many enhancements for macro-mobility (inter-domain) protocols have been proposed, designed and implemented in Mobile IPv6. Hierarchical Mobile IPv6 (HMIPv6) is one of them that is designed to reduce the amount of signaling required and to improve handover speed for mobile connections. This is achieved by introducing a new network entity called Mobility Anchor Point (MAP). This report presents a comparative study of the Hierarchical Mobility IPv6 and Mobile IPv6 protocols and we have narrowed down the scope to micro-mobility (intra-domain). The architecture and operation of each protocol is studied and they are evaluated based on the Quality of Service (QoS) parameter; handover latency. The simulation was carried out by using the Network Simulator-2. The outcome from this simulation has been discussed. From the results, it shows that, HMIPv6 performs best under intra-domain mobility compared to MIPv6. The MIPv6 suffers large handover latency. As enhancement we proposed to HMIPv6 to locate the MAP to be in the middle of the domain with respect to all Access Routers. That gives approximately same distance between MAP and Mobile Node (MN) regardless of the new location of MN, and possible shorter distance. This will reduce the delay since the distance is shorter. As a future work performance analysis is to be carried for the proposed HMIPv6 and compared to HMIPv6.
Abstract: Condition monitoring of electrical power equipment
has attracted considerable attention for many years. The aim of this
paper is to use Labview with Fuzzy Logic controller to build a
simulation system to diagnose transformer faults and monitor its
condition. The front panel of the system was designed using
LabVIEW to enable computer to act as customer-designed
instrument. The dissolved gas-in-oil analysis (DGA) method was
used as technique for oil type transformer diagnosis; meanwhile
terminal voltages and currents analysis method was used for dry type
transformer. Fuzzy Logic was used as expert system that assesses all
information keyed in at the front panel to diagnose and predict the
condition of the transformer. The outcome of the Fuzzy Logic
interpretation will be displayed at front panel of LabVIEW to show
the user the conditions of the transformer at any time.
Abstract: In this paper multivariable predictive PID controller has
been implemented on a multi-inputs multi-outputs control problem
i.e., quadruple tank system, in comparison with a simple multiloop
PI controller. One of the salient feature of this system is an
adjustable transmission zero which can be adjust to operate in both
minimum and non-minimum phase configuration, through the flow
distribution to upper and lower tanks in quadruple tank system.
Stability and performance analysis has also been carried out for this
highly interactive two input two output system, both in minimum
and non-minimum phases. Simulations of control system revealed
that better performance are obtained in predictive PID design.
Abstract: In current common research reports, salient regions
are usually defined as those regions that could present the main
meaningful or semantic contents. However, there are no uniform
saliency metrics that could describe the saliency of implicit image
regions. Most common metrics take those regions as salient regions,
which have many abrupt changes or some unpredictable
characteristics. But, this metric will fail to detect those salient useful
regions with flat textures. In fact, according to human semantic
perceptions, color and texture distinctions are the main characteristics
that could distinct different regions. Thus, we present a novel saliency
metric coupled with color and texture features, and its corresponding
salient region extraction methods. In order to evaluate the
corresponding saliency values of implicit regions in one image, three
main colors and multi-resolution Gabor features are respectively used
for color and texture features. For each region, its saliency value is
actually to evaluate the total sum of its Euclidean distances for other
regions in the color and texture spaces. A special synthesized image
and several practical images with main salient regions are used to
evaluate the performance of the proposed saliency metric and other
several common metrics, i.e., scale saliency, wavelet transform
modulus maxima point density, and important index based metrics.
Experiment results verified that the proposed saliency metric could
achieve more robust performance than those common saliency
metrics.
Abstract: The present paper presents a finite element model and
analysis for the interaction between a piezoresistive tactile sensor and
biological tissues. The tactile sensor is proposed for use in minimally
invasive surgery to deliver tactile information of biological tissues to
surgeons. The proposed sensor measures the relative hardness of soft
contact objects as well as the contact force. Silicone rubbers were
used as the phantom of biological tissues. Finite element analysis of
the silicone rubbers and the mechanical structure of the sensor were
performed using COMSOL Multiphysics (v3.4) environment. The
simulation results verify the capability of the sensor to be used to
differentiate between different kinds of silicone rubber materials.
Abstract: Complexity, as a theoretical background has made it
easier to understand and explain the features and dynamic behavior
of various complex systems. As the common theoretical background
has confirmed, borrowing the terminology for design from the
natural sciences has helped to control and understand urban
complexity. Phenomena like self-organization, evolution and
adaptation are appropriate to describe the formerly inaccessible
characteristics of the complex environment in unpredictable bottomup
systems. Increased computing capacity has been a key element in
capturing the chaotic nature of these systems.
A paradigm shift in urban planning and architectural design has
forced us to give up the illusion of total control in urban
environment, and consequently to seek for novel methods for
steering the development. New methods using dynamic modeling
have offered a real option for more thorough understanding of
complexity and urban processes. At best new approaches may renew
the design processes so that we get a better grip on the complex
world via more flexible processes, support urban environmental
diversity and respond to our needs beyond basic welfare by liberating
ourselves from the standardized minimalism.
A complex system and its features are as such beyond human
ethics. Self-organization or evolution is either good or bad. Their
mechanisms are by nature devoid of reason. They are common in
urban dynamics in both natural processes and gas. They are features
of a complex system, and they cannot be prevented. Yet their
dynamics can be studied and supported.
The paradigm of complexity and new design approaches has been
criticized for a lack of humanity and morality, but the ethical
implications of scientific or computational design processes have not
been much discussed. It is important to distinguish the (unexciting)
ethics of the theory and tools from the ethics of computer aided
processes based on ethical decisions. Urban planning and architecture
cannot be based on the survival of the fittest; however, the natural
dynamics of the system cannot be impeded on grounds of being
“non-human".
In this paper the ethical challenges of using the dynamic models
are contemplated in light of a few examples of new architecture and
dynamic urban models and literature. It is suggested that ethical
challenges in computational design processes could be reframed
under the concepts of responsibility and transparency.