Abstract: Polyurethanes (PURs) are very versatile polymeric
materials with a wide range of physical and chemical properties.
PURs have desirable properties such as high abrasion resistance, tear
strength, shock absorption, flexibility and elasticity. Although they
have relatively poor thermal stability, this can be improved by using
treated clay. Polyurethane/clay nanocomposites have been
synthesized from renewable sources. A polyol for the production of
polyurethane by reaction with an isocyanate was obtained by the
synthesis of palm oil-based oleic acid with glycerol. Dodecylbenzene
sulfonic acid (DBSA) was used as catalyst and emulsifier. The
unmodified clay (kunipia-F) was treated with cetyltrimethyl
ammonium bromide (CTAB-mont) and octadodecylamine (ODAmont).
The d-spacing in CTAB-mont and ODA-mont were 1.571 nm
and 1.798 nm respectively and larger than that of the pure-mont
(1.142 nm). The organoclay was completely intercalated in the
polyurethane, as confirmed by a wide angle x-ray diffraction
(WAXD) pattern.
The results showed that adding clay demonstrated better thermal
stability in comparison with the virgin polyurethane. Onset
degradation of pure PU is at 200oC, and is lower than that of the
CTAB-mont PU and ODA-mont PU which takes place at about
318oC and 330oC, respectively. The mechanical properties (including
the dynamic mechanical properties) of pure polyurethane (PU) and
PU/clay nanocomposites, were measured. The modified organoclay
had a remarkably beneficial effect on the strength and elongation at
break of the nanocomposites, which both increased with increasing
clay content with the increase of the tensile strength of more than
214% and 267% by the addition of only 5 wt% of the
montmorillonite CTAB-mont PU and ODA-mont PU, respectively.
Abstract: Nonlinear finite element method and Serendipity eight
nodes element are used for determining of ground surface settlement
due to tunneling. Linear element with elastic behavior is used for
modeling of lining. Modified Generalized plasticity model with nonassociated
flow rule is applied for analysis of a tunnel in Sao Paulo –
Brazil. The tunnel had analyzed by Lades- model with 16 parameters.
In this work modified Generalized Plasticity is used with 10
parameters, also Mohr-Coulomb model is used to analysis the tunnel.
The results show good agreement with observed results of field data
by modified Generalized Plasticity model than other models. The
obtained result by Mohr-Coulomb model shows less settlement than
other model due to excavation.
Abstract: Development of intelligent assembly cell conception includes new solution kind of how to create structures of automated and flexible assembly system. The current trend of the final product quality increasing is affected by time analysis of the entire manufacturing process. The primary requirement of manufacturing is to produce as many products as soon as possible, at the lowest possible cost, but of course with the highest quality. Such requirements may be satisfied only if all the elements entering and affecting the production cycle are in a fully functional condition. These elements consist of sensory equipment and intelligent control elements that are essential for building intelligent manufacturing systems. Intelligent behavior of the system as the control system will repose on monitoring of important parameters of the system in the real time. Intelligent manufacturing system itself should be a system that can flexibly respond to changes in entering and exiting the process in interaction with the surroundings.
Abstract: The paper presents the case study of hazard
identification and sensitivity of potential resource of emergency
water supply as part of the application of methodology classifying
the resources of drinking water for emergency supply of population.
The case study has been carried out on a selected resource of
emergency water supply in one region of the Czech Republic. The
hazard identification and sensitivity of potential resource of
emergency water supply is based on a unique procedure and
developed general registers of selected types of hazards and
sensitivities. The registers have been developed with the help of the
“Fault Tree Analysis” method in combination with the “What if
method”. The identified hazards for the assessed resource include
hailstorms and torrential rains, drought, soil erosion, accidents of
farm machinery, and agricultural production. The developed registers
of hazards and vulnerabilities and a semi-quantitative assessment of
hazards for individual parts of hydrological structure and
technological elements of presented drilled wells are the basis for a
semi-quantitative risk assessment of potential resource of emergency
supply of population and the subsequent classification of such
resource within the system of crisis planning.
Abstract: The results obtained after incorporating the competence “creativity" to the subject Technical Drawing of the first course of the Degree in Forestry, Technical University of Madrid, are presented in this study.At first, learning activities which could serve two functions at the same time -developing students- creativity and developing other specific competences of the subject- were considered. Besides, changes in the assessment procedure were made and a method which analyzes two aspects of the assessment of the competence creativity was established. On the one hand, the products are evaluated by analyzing the outcomes obtained by students in the essays suggested and by establishing a parameter to assess the creativity expressed in those essays. On the other, an assessment of the student is directly carried out through a psychometric test which has been previously chosen by the team.Moreover, these results can be applied to similar or could be of general application.
Abstract: Genetic algorithms (GAs) have been widely used for
global optimization problems. The GA performance depends highly
on the choice of the search space for each parameter to be optimized.
Often, this choice is a problem-based experience. The search space
being a set of potential solutions may contain the global optimum
and/or other local optimums. A bad choice of this search space
results in poor solutions. In this paper, our approach consists in
extending the search space boundaries during the GA optimization,
only when it is required. This leads to more diversification of GA
population by new solutions that were not available with fixed search
space boundaries. So, these dynamic search spaces can improve the
GA optimization performances. The proposed approach is applied to
power system stabilizer optimization for multimachine power system
(16-generator and 68-bus). The obtained results are evaluated and
compared with those obtained by ordinary GAs. Eigenvalue analysis
and nonlinear system simulation results show the effectiveness of the
proposed approach to damp out the electromechanical oscillation and
enhance the global system stability.
Abstract: We summarize information that facilitates choosing an ontology language for knowledge intensive applications. This paper is a short version of the ontology language state-of-the-art and evolution analysis carried out for choosing an ontology language in the IST Esperonto project. At first, we analyze changes and evolution that took place in the filed of Semantic Web languages during the last years, in particular, around the ontology languages of the RDF/S and OWL family. Second, we present current trends in development of Semantic Web languages, in particular, rule support extensions for Semantic Web languages and emerging ontology languages such as WSMO languages.
Abstract: Industrial surveys shows that manufacturing
companies define the qualities of thermal removing process based on
the dimension and physical appearance of the cutting material
surface. Therefore, the roughness of the surface area of the material
cut by the plasma arc cutting process and the rate of the removed
material by the manual plasma arc cutting machine was importantly
considered. Plasma arc cutter Selco Genesis 90 was used to cut
Standard AISI 1017 Steel of 200 mm x100 mm x 6 mm manually
based on the selected parameters setting. The material removal rate
(MRR) was measured by determining the weight of the specimens
before and after the cutting process. The surface roughness (SR)
analysis was conducted using Mitutoyo CS-3100 to determine the
average roughness value (Ra). Taguchi method was utilized to
achieve optimum condition for both outputs studied. The
microstructure analysis in the region of the cutting surface is
performed using SEM. The results reveal that the SR values are
inversely proportional to the MRR values. The quality of the surface
roughness depends on the dross peak that occurred after the cutting
process.
Abstract: Dual bell nozzle is a promising one among the altitude
adaptation nozzle concepts, which offer increased nozzle
performance in rocket engines. Its advantage is the simplicity it offers
due to the absence of any additional mechanical device or movable
parts. Hence it offers reliability along with improved nozzle
performance as demanded by future launch vehicles. Among other
issues, the flow transition to the extension nozzle of a dual bell
nozzle is one of the major issues being studied in the development of
dual bell nozzle. A parameter named over-expansion factor, which
controls the value of the wall inflection angle, has been reported to
have substantial influence in this transition process. This paper
studies, through CFD and cold flow experiments, the effect of overexpansion
factor on flow transition in dual bell nozzles.
Abstract: In this paper, we propose an improved fast search
algorithm using combined histogram features and temporal division
method for short MPEG video clips from large video database. There
are two types of histogram features used to generate more robust
features. The first one is based on the adjacent pixel intensity
difference quantization (APIDQ) algorithm, which had been reliably
applied to human face recognition previously. An APIDQ histogram is
utilized as the feature vector of the frame image. Another one is
ordinal feature which is robust to color distortion. Combined with
active search [4], a temporal pruning algorithm, fast and robust video
search can be realized. The proposed search algorithm has been
evaluated by 6 hours of video to search for given 200 MPEG video
clips which each length is 30 seconds. Experimental results show the
proposed algorithm can detect the similar video clip in merely 120ms,
and Equal Error Rate (ERR) of 1% is achieved, which is more
accurately and robust than conventional fast video search algorithm.
Abstract: The use of e-business in small and medium-sized
enterprises (SMEs) has been recently received an enormous attention
in information systems research by both academic and practitioners.
With the adoption of new and efficient technologies to enhance
businesses, Thai SMEs should be able to compete worldwide.
Unfortunately, most of the owners are not used to new technologies.
It is clear that most Thai SMEs prefer to work manually rather than
electronically. This paper aims to provide a fundamental conceptual
framework for E-business adoption by Thai SMEs. Rooted in
Knowledge transfer model, several factors are identified, which drive
and enable e-business adoption. By overlooking the benefits
associated with implementing new technologies, it is difficult for
Thai SMEs to perform well enough to compete globally. The paper
also helps Thai SMEs to understand factors related to E-business
adoption.
Abstract: This paper addresses linear quadratic regulation (LQR)
for variable speed variable pitch wind turbines. Because of the
inherent nonlinearity of wind turbine, a set of operating conditions is
identified and then a LQR controller is designed for each operating
point. The feedback controller gains are then interpolated linearly to
get control law for the entire operating region. Besides, the
aerodynamic torque and effective wind speed are estimated online to
get the gain-scheduling variable for implementing the controller. The
potential of the method is verified through simulation with the help of
MATLAB/Simulink and GH Bladed. The performance and
mechanical load when using LQR are also compared with that when
using PI controller.
Abstract: Environmental contamination is a common problem in ex-industrial and industrial sites. This article gives a brief description of general applied environmental investigation methodologies and possible remediation applications in Latvia. Most of contaminated areas are situated in former and active industrial, military areas and ports. Industrial and logistic activities very often have been with great impact for more than hundred years thus the contamination level with heavy metals, hydrocarbons, pesticides, persistent organic pollutants is high and is threatening health and environment in general. 242 territories now are numbered as contaminated and fixed in the National Register of contaminated territories in Latvia. Research and remediation of contamination in densely populated areas are of important environmental policy domain. Four different investigation case studies of contaminated areas are given describing the history of use, environmental quality assessment as well as planned environmental management actions. All four case study locations are situated in Riga - the capital of the Republic of Latvia. The aim of this paper is to analyze the situation and problems with management of contaminated areas in Latvia, give description of field research methods and recommendations for remediation industry based on scientific data and innovations.
Abstract: The peel of dragon fruit is a byproduct left over after consuming. Normally, the use of plants as antioxidant source must be dried before further process. Therefore, the aim of this study is interesting to dry the peel by heat pump dryer (45 ºC) and fluidized bed dryer (110 º C) compared with the sun drying method. The sample with initial moisture content of about 85-91% wet basis was dried down to about 10% wet basis where it took 620 and 25 min for heat pump dryer and fluidized bed dryer, respectively. However, the sun drying took about 900 min to dry the peel. After that, sample was evaluated antioxidant activity, -carotene and betalains contents. The results found that the antioxidant activity and betalains contents of dried peel obtained from heat pump and fluidized bed dryings were significantly higher than that sun drying (p 0.05). Moreover, the drying by heat pump provided the highest -carotene content.
Abstract: We present a novel scheme to recognize isolated speech
signals using certain statistical parameters derived from those signals.
The determination of the statistical estimates is based on extracted
signal information rather than the original signal information in
order to reduce the computational complexity. Subtle details of
these estimates, after extracting the speech signal from ambience
noise, are first exploited to segregate the polysyllabic words from
the monosyllabic ones. Precise recognition of each distinct word is
then carried out by analyzing the histogram, obtained from these
information.
Abstract: In this study the elastic-plastic stress distribution in
weld-bonded joint, fabricated from austenitic stainless steel (AISI
304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011,
subjected to axial loading is investigated. This is needed to improve
design procedures and welding codes, and saving efforts in the
cumbersome experiments and analysis. Therefore, a complete 3-D
finite element modelling and analysis of spot welded, bonded and
weld-bonded joints under axial loading conditions is carried out. A
comprehensive systematic experimental program is conducted to
determine many properties and quantities, of the base metals and the
adhesive, needed for FE modelling, such like the elastic – plastic
properties, modulus of elasticity, fracture limit, the nugget and heat
affected zones (HAZ) properties, etc. Consequently, the finite
element models developed, for each case, are used to evaluate
stresses distributions across the entire joint, in both the elastic and
plastic regions. The stress distribution curves are obtained,
particularly in the elastic regions and found to be consistent and in
excellent agreement with the published data. Furthermore, the
stresses distributions are obtained in the weld-bonded joint and
display the best results with almost uniform smooth distribution
compared to spot and bonded cases. The stress concentration peaks at
the edges of the weld-bonded region, are almost eliminated resulting
in achieving the strongest joint of all processes.
Abstract: Evolvable hardware (EHW) refers to a selfreconfiguration
hardware design, where the configuration is under
the control of an evolutionary algorithm (EA). A lot of research has
been done in this area several different EA have been introduced.
Every time a specific EA is chosen for solving a particular problem,
all its components, such as population size, initialization, selection
mechanism, mutation rate, and genetic operators, should be selected
in order to achieve the best results. In the last three decade a lot of
research has been carried out in order to identify the best parameters
for the EA-s components for different “test-problems". However
different researchers propose different solutions. In this paper the
behaviour of mutation rate on (1+λ) evolution strategy (ES) for
designing logic circuits, which has not been done before, has been
deeply analyzed. The mutation rate for an EHW system modifies
values of the logic cell inputs, the cell type (for example from AND
to NOR) and the circuit output. The behaviour of the mutation has
been analyzed based on the number of generations, genotype
redundancy and number of logic gates used for the evolved circuits.
The experimental results found provide the behaviour of the mutation
rate to be used during evolution for the design and optimization of
logic circuits. The researches on the best mutation rate during the last
40 years are also summarized.
Abstract: A model of (4, 4) single-walled boron-nitride nanotube as a representative of armchair boron-nitride nanotubes studied. At first the structure optimization performed and then Nuclear Magnetic Resonance parameters (NMR) by Density Functional Theory (DFT) method at 11B and 15N nuclei calculated. Resulted parameters evaluation presents electrostatic environment heterogeneity along the nanotube and especially at the ends but the nuclei in a layer feel the same electrostatic environment. All of calculations carried out using Gaussian 98 Software package.
Abstract: In this paper we present the modeling, design, and
experimental testing of a nerve cuff multi-electrode system for
diameter-selective vagus nerve stimulation.
The multi-electrode system contained ninety-nine platinum
electrodes embedded within a self-curling spiral silicone sheet. The
electrodes were organized in a matrix having nine parallel groups,
each containing eleven electrodes.
Preliminary testing of the nerve cuff was performed in an isolated
segment of a swinish left cervical vagus nerve. For selective vagus
nerve stimulation, precisely defined current quasitrapezoidal,
asymmetric and biphasic stimulating pulses were applied to
preselected locations along the left vagus segment via appointed
group of three electrodes within the cuff. Selective stimulation was
obtained by anodal block. However, these pulses may not be safe for
a long-term application because of a frequently used high imbalance
between the cathodic and anodic part of the stimulating pulse.
Preliminary results show that the cuff was capable of exciting A
and B-fibres, and, that for a certain range of parameters used in
stimulating pulses, the contribution of A-fibres to the CAP was
slightly reduced and the contribution of B-fibres was slightly larger.
Results also showed that measured CAPs are not greatly
influenced by the imbalance between a charge Qc injected in cathodic
and Qa in anodic phase of quasitrapezoidal, asymmetric and biphasic
pulses.
Abstract: This paper proposes a VPN Accelerator Board
(VPN-AB), a virtual private network (VPN) protocol designed for
trust channel security system (TCSS). TCSS supports safety
communication channel between security nodes in internet. It
furnishes authentication, confidentiality, integrity, and access control
to security node to transmit data packets with IPsec protocol. TCSS
consists of internet key exchange block, security association block,
and IPsec engine block. The internet key exchange block negotiates
crypto algorithm and key used in IPsec engine block. Security
Association blocks setting-up and manages security association
information. IPsec engine block treats IPsec packets and consists of
networking functions for communication. The IPsec engine block
should be embodied by H/W and in-line mode transaction for high
speed IPsec processing. Our VPN-AB is implemented with high speed
security processor that supports many cryptographic algorithms and
in-line mode. We evaluate a small TCSS communication environment,
and measure a performance of VPN-AB in the environment. The
experiment results show that VPN-AB gets a performance throughput
of maximum 15.645Gbps when we set the IPsec protocol with
3DES-HMAC-MD5 tunnel mode.