Abstract: Dual phase steels (DPS)s have a microstructure
consisting of a hard second phase called Martensite in the soft Ferrite
matrix. In recent years, there has been interest in dual-phase steels,
because the application of these materials has made significant usage;
particularly in the automotive sector Composite microstructure of
(DPS)s exhibit interesting characteristic mechanical properties such
as continuous yielding, low yield stress to tensile strength
ratios(YS/UTS), and relatively high formability; which offer
advantages compared with conventional high strength low alloy
steels(HSLAS). The research dealt with the characterization of
damage in (DPS)s. In this study by review the mechanisms of failure
due to volume fraction of martensite second phase; a new method is
introduced to identifying the mechanisms of failure in the various
phases of these types of steels. In this method the acoustic emission
(AE) technique was used to detect damage progression. These failure
mechanisms consist of Ferrite-Martensite interface decohesion and/or
martensite phase fracture. For this aim, dual phase steels with
different volume fraction of martensite second phase has provided by
various heat treatment methods on a low carbon steel (0.1% C), and
then AE monitoring is used during tensile test of these DPSs. From
AE measurements and an energy ratio curve elaborated from the
value of AE energy (it was obtained as the ratio between the strain
energy to the acoustic energy), that allows detecting important
events, corresponding to the sudden drops. These AE signals events
associated with various failure mechanisms are classified for ferrite
and (DPS)s with various amount of Vm and different martensite
morphology. It is found that AE energy increase with increasing Vm.
This increasing of AE energy is because of more contribution of
martensite fracture in the failure of samples with higher Vm. Final
results show a good relationship between the AE signals and the
mechanisms of failure.
Abstract: Road signs are the elements of roads with a lot of
influence in driver-s behavior. So that signals can fulfill its function,
they must overcome visibility and durability requirements,
particularly needed at night, when the coefficient of retroreflection
becomes a decisive factor in ensuring road safety. Accepting that the
visibility of the signage has implications for people-s safety, we
understand the importance to fulfill its function: to foster the highest
standards of service and safety in drivers. The usual conditions of
perception of any sign are determined by: age of the driver, reflective
material, luminosity, vehicle speed and emplacement. In this way,
this paper evaluates the different signals to increase the safety road.
Abstract: One of the most important requirements for the
operation and planning activities of an electrical utility is the
prediction of load for the next hour to several days out, known as
short term load forecasting. This paper presents the development of
an artificial neural network based short-term load forecasting model.
The model can forecast daily load profiles with a load time of one
day for next 24 hours. In this method can divide days of year with
using average temperature. Groups make according linearity rate of
curve. Ultimate forecast for each group obtain with considering
weekday and weekend. This paper investigates effects of temperature
and humidity on consuming curve. For forecasting load curve of
holidays at first forecast pick and valley and then the neural network
forecast is re-shaped with the new data. The ANN-based load models
are trained using hourly historical. Load data and daily historical
max/min temperature and humidity data. The results of testing the
system on data from Yazd utility are reported.
Abstract: The halophilic proteinase showed a maximal activity
at 50°C and pH 9~10, in 20% NaCl and was highly stabilized by
NaCl. It was able to hydrolyse natural actomyosin (NAM), collagen
and anchovy protein. For NAM hydrolysis, the myosin heavy chain
was completely digested by halophilic proteinase as evidenced by the
lowest band intensity remaining, but partially hydrolysed actin. The
SR5-3 proteinase was also capable hydrolyzing two major
components of collagen, β- and α-compounds, effectively. The
degree of hydrolysis (DH) of the halophilic proteinase and
commercial proteinases (Novozyme, Neutrase, chymotrypsin and
Flavourzyme) on the anchovy protein, were compared, and it was
found that the proteinase showed a greater degree of hydrolysis
towards anchovy protein than that from commercial proteinases. DH
of halophilic proteinase was sharply enhanced according to the
increase in the concentration of enzyme from 0.035 U to 0.105 U.
The results warranting that the acceleration of the production of fish
sauce with higher quality, may be achieved by adding of the
halophilic proteinase from this bacterium.
Abstract: As seen in literature, about 70% of the improvement initiatives fail, and a significant number do not even get started. This paper analyses the problem of failing initiatives on Software Process Improvement (SPI), and proposes good practices supported by motivational tools that can help minimizing failures. It elaborates on the hypothesis that human factors are poorly addressed by deployers, especially because implementation guides usually emphasize only technical factors. This research was conducted with SPI deployers and analyses 32 SPI initiatives. The results indicate that although human factors are not commonly highlighted in guidelines, the successful initiatives usually address human factors implicitly. This research shows that practices based on human factors indeed perform a crucial role on successful implantations of SPI, proposes change management as a theoretical framework to introduce those practices in the SPI context and suggests some motivational tools based on SPI deployers experience to support it.
Abstract: This paper presents the applicability of artificial
neural networks for 24 hour ahead solar power generation forecasting
of a 20 kW photovoltaic system, the developed forecasting is suitable
for a reliable Microgrid energy management. In total four neural
networks were proposed, namely: multi-layred perceptron, radial
basis function, recurrent and a neural network ensemble consisting in
ensemble of bagged networks. Forecasting reliability of the proposed
neural networks was carried out in terms forecasting error
performance basing on statistical and graphical methods. The
experimental results showed that all the proposed networks achieved
an acceptable forecasting accuracy. In term of comparison the neural
network ensemble gives the highest precision forecasting comparing
to the conventional networks. In fact, each network of the ensemble
over-fits to some extent and leads to a diversity which enhances the
noise tolerance and the forecasting generalization performance
comparing to the conventional networks.
Abstract: Online news websites are one of the main and wide areas of Mass Media. Since the nineties several Jordanian newspapers were introduced to the World Wide Web to reach various and large numbers of audiances. Examples of these newspapers that have online version are Al-Rai, Ad-Dustor and AlGhad. Other pure online news websites include Ammon and Rum. The main aim of this study is to evaluate online newspaper websites using two assessment measures; usability and web content. This aim is achieved by using a questionnaire based evaluation which is based on the definition of usability and web content in the ISO document as the standard number 9241-part 11. The results are obtained based on 204 audiences- responses. The results of the research showed that the usability factor is relatively good for all Jordanian online newspapers whereas the web content factor is moderate.
Abstract: The building sector is the largest energy consumer and
CO2 emitter in the European Union (EU) and therefore the active
reduction of energy consumption and elimination of energy wastage
are among the main goals in it. Healthy housing and energy
efficiency are affected by many factors which set challenges to
monitoring, control and research of indoor air quality (IAQ) and
energy consumption, especially in old buildings. These challenges
include measurement and equipment costs, for example.
Additionally, the measurement results are difficult to interpret and
their usage in the ventilation control is also limited when taking into
account the energy efficiency of housing at the same time. The main
goal of this study is to develop a cost-effective building monitoring
and control system especially for old buildings. The starting point or
keyword of the development process is a wireless system; otherwise
the installation costs become too high. As the main result, this paper
describes an idea of a wireless building monitoring and control
system. The first prototype of the system has been installed in 10
residential buildings and in 10 school buildings located in the City of
Kuopio, Finland.
Abstract: This paper presents a watermarking protocol able to
solve the well-known “customer-s right problem" and “unbinding
problem". In particular, the protocol has been purposely designed
to be adopted in a web context, where users wanting to buy digital
contents are usually neither provided with digital certificates issued
by certification authorities (CAs) nor able to autonomously perform
specific security actions. Furthermore, the protocol enables users to
keep their identities unexposed during web transactions as well as
allows guilty buyers, i.e. who are responsible distributors of illegal
replicas, to be unambiguously identified. Finally, the protocol has
been designed so that web content providers (CPs) can exploit
copyright protection services supplied by web service providers (SPs)
in a security context. Thus, CPs can take advantage of complex
services without having to directly implement them.
Abstract: This work relates the development of an optical fiber
(OF) sensor for the detection and quantification of single walled
carbon nanotubes in aqueous solutions. The developed OF displays a
compact design, it requires less expensive materials and equipment
as well as low volume of sample (0.2 mL). This methodology was
also validated by the comparison of its analytical performance with
that of a standard methodology based on ultraviolet-visible
spectroscopy. The developed OF sensor follows the general SDS
calibration proposed for OF sensors as a more suitable calibration
fitting compared with classical calibrations.
Abstract: Article devoted to the development of technologies
for medicine and agroecology by using plant organelle – spherosome.
Technological method of purification and isolation of this organelle
by using novel nanostructured carbon sorbent – “nanocarbosorb"
ARK type are presented. Also the methods of preparation of
nanocontainers based on using of spherosome with loaded isosorbide
dinitrate, piroxicam or diclofenak are exhibited. We found that the
spherosome could be applied for ecological aims as bioregulator and
also as biosensor for determination of ammonia ions in water
reservoirs at concentration range 1mM to 100mM.
Abstract: Dispersions of casein micelles (CM) were studied at a
constant protein concentration of 5 wt % in high NaCl environment
ranging from 0% to 12% by Dynamic light scattering (DLS) and
Fourier Transform Infrared (FTIR). The rehydration profiles obtained
were interpreted in term of wetting, swelling and dispersion stages by
using a turbidity method. Two behaviours were observed depending
on the salt concentration. The first behaviour (low salt concentration)
presents a typical rehydration profile with a significant change
between 3 and 6% NaCl indicating quick wetting, swelling and long
dispersion stage. On the opposite, the dispersion stage of the second
behaviour (high salt concentration) was significantly shortened
indicating a strong modification of the protein backbone. A salt
increase result to a destabilization of the micelle and the formation of
mini-micelles more or less aggregated indicating an average micelles
size ranging from 100 to 200 nm. For the first time, the estimations
of secondary structural elements (irregular, ß-sheet, α-helix and turn)
by the Amide III assignments were correlated with results from
Amide I.
Abstract: There is growing interest in biodiesel (fatty acid
methyl ester or FAME) because of the similarity in its properties
when compared to those of diesel fuels. Diesel engines operated on
biodiesel have lower emissions of carbon monoxide, unburned
hydrocarbons, particulate matter, and air toxics than when operated
on petroleum-based diesel fuel. Production of fatty acid methyl ester
(FAME) from rapeseed (nonedible oil) fatty acid distillate having
high free fatty acids (FFA) was investigated in this work. Conditions
for esterification process of rapeseed oil were 1.8 % H2SO4 as
catalyst, MeOH/oil of molar ratio 2 : 0.1 and reaction temperature
65 °C, for a period of 3h. The yield of methyl ester was > 90 % in 1
h.
The amount of FFA was reduced from 93 wt % to less than 2 wt %
at the end of the esterification process. The FAME was pureed by
neutralization with 1 M sodium hydroxide in water solution at a
reaction temperature of 62 °C. The final FAME product met with the
biodiesel quality standard, and ASTM D 6751.
Abstract: Detection of squirrel cage induction motor (SCIM) broken bars has long been an important but difficult job in the detection area of motor faults. Early detection of this abnormality in the motor would help to avoid costly breakdowns. A new detection method based on particle swarm optimization (PSO) is presented in this paper. Stator current in an induction motor will be measured and characteristic frequency components of faylted rotor will be detected by minimizing a fitness function using pso. Supply frequency and side band frequencies and their amplitudes can be estimated by the proposed method. The proposed method is applied to a faulty motor with one and two broken bars in different loading condition. Experimental results prove that the proposed method is effective and applicable.
Abstract: This research investigates the suitability of fuel oil in
improving gypseous soil. A detailed laboratory tests were carried-out
on two soils (soil I with 51.6% gypsum content, and soil II with
26.55%), where the two soils were obtained from Al-Therthar site
(Al-Anbar Province-Iraq).
This study examines the improvement of soil properties using the
gypsum material which is locally available with low cost to minimize
the effect of moisture on these soils by using the fuel oil. This study
was conducted on two models of the soil gypsum, from the Tharthar
area. The first model was sandy soil with Gypsum content of (51.6%)
and the second is clayey soil and the content of Gypsum is (26.55%).
The program included tests measuring the permeability and
compressibility of the soil and their collapse properties. The shear
strength of the soil and the amounts of weight loss of fuel oil due to
drying had been found. These tests have been conducted on the
treated and untreated soils to observe the effect of soil treatment on
the engineering properties when mixed with varying degrees of fuel
oil with the equivalent of the water content.
The results showed that fuel oil is a good material to modify the
basic properties of the gypseous soil of collapsibility and
permeability, which are the main problems of this soil and retained
the soil by an appropriate amount of the cohesion suitable for
carrying the loads from the structure.
Abstract: This paper analyzes the extent to which the justices of
the U.S. Supreme Court cast votes that support the positions of the
president, or more generally the Executive Branch. Can presidents
count on such deference from those justices they nominate or those
whom are nominated by other presidents of the same party? Or, do
the justices demonstrate judicial independence and impartiality such
that they are not so predisposed to vote in favor of arguments of their
nominating president-s party? The results suggest that while in
general the justices do not exhibit any marked tendency to partisan
support of presidents, more recent and conservative Supreme Court
justices are significantly more likely to support Republican
presidents.
Abstract: Virtual Assembly (VA) is one of the key technologies
in advanced manufacturing field. It is a promising application of
virtual reality in design and manufacturing field. It has drawn much
interest from industries and research institutes in the last two decades.
This paper describes a process for integrating an interactive Virtual
Reality-based assembly simulation of a digital mockup with the
CAD/CAM infrastructure. The necessary hardware and software
preconditions for the process are explained so that it can easily be
adopted by non VR experts. The article outlines how assembly
simulation can improve the CAD/CAM procedures and structures;
how CAD model preparations have to be carried out and which
virtual environment requirements have to be fulfilled. The issue of
data transfer is also explained in the paper. The other challenges and
requirements like anti-aliasing and collision detection have also been
explained. Finally, a VA simulation has been carried out for a ball
valve assembly and a car door assembly with the help of Vizard
virtual reality toolkit in a semi-immersive environment and their
performance analysis has been done on different workstations to
evaluate the importance of graphical processing unit (GPU) in the
field of VA.
Abstract: This paper presents the result of three senior capstone
projects at the Department of Computer Engineering, Prince of
Songkla University, Thailand. These projects focus on developing an
examination management system for the Faculty of Engineering in
order to manage the examination both the examination room
assignments and the examination proctor assignments in each room.
The current version of the software is a web-based application. The
developed software allows the examination proctors to select their
scheduled time online while each subject is assigned to each available
examination room according to its type and the room capacity. The
developed system is evaluated using real data by prospective users of
the system. Several suggestions for further improvements are given
by the testers. Even though the features of the developed software are
not superior, the developing process can be a case study for a projectbased
teaching style. Furthermore, the process of developing this
software can show several issues in developing an educational
support application.
Abstract: This paper presents an optimal design of linear phase
digital high pass finite impulse response (FIR) filter using Improved
Particle Swarm Optimization (IPSO). In the design process, the filter
length, pass band and stop band frequencies, feasible pass band and
stop band ripple sizes are specified. FIR filter design is a multi-modal
optimization problem. An iterative method is introduced to find the
optimal solution of FIR filter design problem. Evolutionary
algorithms like real code genetic algorithm (RGA), particle swarm
optimization (PSO), improved particle swarm optimization (IPSO)
have been used in this work for the design of linear phase high pass
FIR filter. IPSO is an improved PSO that proposes a new definition
for the velocity vector and swarm updating and hence the solution
quality is improved. A comparison of simulation results reveals the
optimization efficacy of the algorithm over the prevailing
optimization techniques for the solution of the multimodal, nondifferentiable,
highly non-linear, and constrained FIR filter design
problems.
Abstract: As known, the guard wires of overhead high voltage
are usually grounded through the grounding systems of support and
of the terminal stations. They do affect the zero sequence impedance
value of the line, Z0, which is generally, calculated assuming that the
wires guard are at ground potential. In this way it is not considered
the effect of the resistances of earth of supports and stations. In this
work is formed a formula for the calculation of Z0 which takes
account of said resistances. Is also proposed a method of calculating
the impedance zero sequence overhead lines in which, in various
sections or spans, the guard wires are connected to the supports, or
isolated from them, or are absent. Parametric analysis is given for
lines 220 kV and 400 kV, which shows the extent of the errors made
with traditional methods of calculation.