Abstract: Supermarkets are the most electricity-intensive type of
commercial buildings. The unsuitable indoor environment of a
supermarket provided by abnormal HVAC operations incurs waste
energy consumption in refrigeration systems. This current study
briefly describes significantly solid backgrounds and proposes easyto-
use analysis terminology for investigating the impact of HVAC
operations on refrigeration power consumption using the field-test
data obtained from building automation system (BAS). With solid
backgrounds and prior knowledge, expected energy interactions
between HVAC and refrigeration systems are proposed through
Pearson’s correlation analysis (R value) by considering correlations
between equipment power consumption and dominantly independent
variables (driving force conditions).The R value can be conveniently
utilized to evaluate how strong relations between equipment
operations and driving force parameters are. The calculated R values
obtained from field data are compared to expected ranges of R values
computed by energy interaction methodology. The comparisons can
separate the operational conditions of equipment into faulty and
normal conditions. This analysis can simply investigate the condition
of equipment operations or building sensors because equipment could
be abnormal conditions due to routine operations or faulty
commissioning processes in field tests. With systematically solid and
easy-to-use backgrounds of interactions provided in the present
article, the procedures can be utilized as a tool to evaluate the proper
commissioning and routine operations of HVAC and refrigeration
systems to detect simple faults (e.g. sensors and driving force
environment of refrigeration systems and equipment set-point) and
optimize power consumption in supermarket buildings. Moreover,
the analysis will be used to further study the FDD research for
supermarkets in future.
Abstract: In this paper a scheme is proposed for generating
a programmable current reference which can be implemented
in the CMOS technology. The current can be varied over a
wide range by changing an external voltage applied to one
of the control gates of FGMOS (Floating Gate MOSFET).
For a range of supply voltages and temperature, CMOS
current reference is found to be dependent, this dependence
is compensated by subtracting two current outputs with the
same dependencies on the supply voltage and temperature.
The system performance is found to improve with the
use of FGMOS. Mathematical analysis of the proposed
circuit is done to establish supply voltage and temperature
independence. Simulation and performance evaluation of the
proposed current reference circuit is done using TANNER
EDA Tools. The current reference shows the supply and
temperature dependencies of 520 ppm/V and 312 ppm/oC,
respectively. The proposed current reference can operate down
to 0.9 V supply.
Abstract: This paper presents the design analysis of saddle
support of a horizontal pressure vessel. Since saddle have the vital
role to support the pressure vessel and to maintain its stability, it
should be designed in such a way that it can afford the vessel load
and internal pressure of the vessel due to liquid contained in the
vessel. A model of horizontal pressure vessel and saddle support is
created in ANSYS. Stresses are calculated using mathematical
approach and ANSYS software. The analysis reveals the zone of high
localized stress at the junction part of the pressure vessel and saddle
support due to operating conditions. The results obtained by both the
methods are compared with allowable stress value for safe designing.
Abstract: FengShui, an old Chinese discipline, dates back to
more than 5000 years, is one of the design principles that aim at
creating habitable and sustainable spaces in harmony with nature by
systematizing data within its own structure. Having emerged from
Chinese mysticism and embodying elements of faith in its principles,
FengShui argues that the positive energy in the environment channels
human behavior and psychology. This argument is supported with the
thesis of quantum physics that ‘everything is made up of energy’ and
gains an important place.
In spaces where living and working take place with several
principles and systematized rules, FengShui promises a happier, more
peaceful and comfortable life by influencing human psychology, acts,
and soul as well as the professional and social life of the individual.
Observing these design properties in houses, workplaces, offices, the
environment, and daily life as a design paradigm is significant. In this
study, how FengShui, a Central Asian culture emanated from Chinese
mysticism, shapes design and how it is used as an element of
sustainable design will be explained.
Abstract: Stochastic User Equilibrium (SUE) model is a widely
used traffic assignment model in transportation planning, which is
regarded more advanced than Deterministic User Equilibrium (DUE)
model. However, a problem exists that the performance of the SUE
model depends on its error term parameter. The objective of this
paper is to propose a systematic method of determining the
appropriate error term parameter value for the SUE model. First, the
significance of the parameter is explored through a numerical
example. Second, the parameter calibration method is developed
based on the Logit-based route choice model. The calibration process
is realized through multiple nonlinear regression, using sequential
quadratic programming combined with least square method. Finally,
case analysis is conducted to demonstrate the application of the
calibration process and validate the better performance of the SUE
model calibrated by the proposed method compared to the SUE
models under other parameter values and the DUE model.
Abstract: This paper considers the characterization of a complex
electromagnetic environment due to multiple sources of
electromagnetic radiation as a five-dimensional surface which can be
described by a set of several surface sections including: instant EM
field intensity distribution maps at a given frequency and altitude,
instantaneous spectrum at a given location in space and the time
evolution of the electromagnetic field spectrum at a given point in
space. This characterization if done over time can enable the
exposure levels of Radio Frequency Radiation at every point in the
analysis area to be determined and results interpreted based on
comparison of the determined RFR exposure level with the safe
guidelines for general public exposure given by recognized body
such as the International commission on non-ionizing radiation
protection (ICNIRP), Institute of Electrical and Electronic Engineers
(IEEE), the National Radiation Protection Authority (NRPA).
Abstract: The systematic evaluation of manufacturing
technologies with regard to the potential for product designing
constitutes a major challenge. Until now, conventional evaluation
methods primarily consider the costs of manufacturing technologies.
Thus, the potential of manufacturing technologies for achieving
additional product design features is not completely captured. To
compensate this deficit, final evaluations of new technologies are
mainly intuitive in practice. Therefore, an additional evaluation
dimension is needed which takes the potential of manufacturing
technologies for specific realizable product designs into account. In
this paper, we present the approach of an evaluation method for
selecting manufacturing technologies with regard to their potential
for product designing. This research is done within the Fraunhofer
innovation cluster »AdaM« (Adaptive Manufacturing) which targets
the development of resource efficient and adaptive manufacturing
technology processes for complex turbomachinery components.
Abstract: This paper involved the performance of a hightemperature
X-Ray powder diffraction analysis (XRD) of a sample of
chemical gypsum generated in the production of titanium white; this
gypsum originates by neutralizing highly acidic water with limestone
suspension. Specifically, it was gypsum formed in the first stage of
neutralization when the resulting material contains, apart from
gypsum, a number of waste products resulting from the
decomposition of ilmenite by sulphuric acid. So it can be described as
red titanogypsum. By conducting the experiment using XRD
apparatus Bruker D8 Advance with a Cu anode (λkα=1.54184 Å)
equipped with high-temperature chamber Anton Paar HTK 16, it was
possible to identify clearly in the sample each phase transition in the
system of CaSO4·xH2O.
Abstract: Caused by shorter product life cycles and higher
product variety the importance of production ramp ups is increasing.
Even though companies are aware of that fact, up to 40% of the ramp
up projects still miss technical and economical requirements. The
success of a ramp up depends on the planning of human factors,
organizational aspects and technological solutions. Since only partly
considered in scientific literature, this paper lays its focus on the
human factor during production ramp up. There are only incoherent
methods which address the problems in this area. A systematic and
holistic method to improve the capabilities of the employees during
ramp up is missing. The Harada Method is a relatively young
approach for developing highly-skilled workers. It consists of
different worksheets which help employees to set guidelines and
reach overall objectives. This approach is going to be transferred into
a tool for ramp up management.
Abstract: Diabetes is a growing health problem in worldwide.
Especially, the patients with Type 1 diabetes need strict glycemic
control because they have deficiency of insulin production. This
paper attempts to control blood glucose based on body mathematical
body model. The Bergman minimal mathematical model is used to
develop the nonlinear controller. A novel back-stepping based sliding
mode control (B-SMC) strategy is proposed as a solution that
guarantees practical tracking of a desired glucose concentration. In
order to show the performance of the proposed design, it is compared
with conventional linear and fuzzy controllers which have been done
in previous researches. The numerical simulation result shows the
advantages of sliding mode back stepping controller design to linear
and fuzzy controllers.
Abstract: The mathematical analysis on radiation obtained and
the development of the solar photovoltaic (PV) array groundwater
pumping is needed in the rural areas of Thohoyandou for sizing and
power performance subject to the climate conditions within the area.
A simple methodology approach is developed for the directed
coupled solar, controller and submersible ground water pump system.
The system consists of a PV array, pump controller and submerged
pump, battery backup and charger controller. For this reason, the
theoretical solar radiation is obtained for optimal predictions and
system performance in order to achieve different design and
operating parameters. Here the examination of the PV schematic
module in a Direct Current (DC) application is used for obtainable
maximum solar power energy for water pumping. In this paper, a
simple efficient photovoltaic water pumping system is presented with
its theoretical studies and mathematical modeling of photovoltaics
(PV) system.
Abstract: The assessment of the risk posed by a borrower to a
lender is one of the common problems that financial institutions have
to deal with. Consumers vying for a mortgage are generally
compared to each other by the use of a number called the Credit
Score, which is generated by applying a mathematical algorithm to
information in the applicant’s credit report. The higher the credit
score, the lower the risk posed by the candidate, and the better he is
to be taken on by the lender. The objective of the present work is to
use fuzzy logic and linguistic rules to create a model that generates
Credit Scores.
Abstract: The main objective of this study was to identify
factors and conditions that motivated and encouraged students
towards the math class and the factors that made this class an
attractive and lovely one. To do this end, questionnaires consisting of
15 questions were distributed among 85 math teachers working in
schools of Zahedan. Having collected and reviewed these
questionnaires, it was shown that doing activity in math class
(activity of students while teaching) and previous math teachers'
behaviors have had much impact on encouraging the students
towards mathematics. Separation of educational classroom of
mathematics from the main classroom (which is decorated with crafts
created by students themselves with regard to math book including
article, wall newspaper, figures and formulas), peers, size and
appearance of math book, first grade teachers in each educational
level, among whom the Elementary first grade teachers had more
importance and impact, were among the most influential and
important factors in this regard. Then, school environment, family,
conducting research related to mathematics, its application in daily
life and other courses and studying the history of mathematics were
categorized as important factors that would increase the students’
interest in mathematics.
Abstract: Kinematic data wisely correlate vector quantities in
space to scalar parameters in time to assess the degree of symmetry
between the intact limb and the amputated limb with respect to a
normal model derived from the gait of control group participants.
Furthermore, these particular data allow a doctor to preliminarily
evaluate the usefulness of a certain rehabilitation therapy.
Kinetic curves allow the analysis of ground reaction forces (GRFs)
to assess the appropriateness of human motion.
Electromyography (EMG) allows the analysis of the fundamental
lower limb force contributions to quantify the level of gait
asymmetry. However, the use of this technological tool is expensive
and requires patient’s hospitalization. This research work suggests
overcoming the above limitations by applying artificial neural
networks.
Abstract: Composite materials have important assets compared
to traditional materials. They bring many functional advantages:
lightness, mechanical resistance and chemical, etc. In the present
study we examine the effect of a circular central notch and a precrack
on the tensile fracture of two woven composite materials. The tensile
tests were applied to a standardized specimen, notched and a
precarcked (orientation of the crack 0°, 45° and 90°). These tensile
tests were elaborated according to an experimental planning design of
the type 23.31 requiring 24 experiments with three repetitions. By the
analysis of regression, we obtained a mathematical model describing
the maximum load according to the influential parameters (hole
diameter, precrack length, angle of a precrack orientation). The
specimens precracked at 90° have a better behavior than those having
a precrack at 45° and still better than those having of the precracks
oriented at 0°. In addition the maximum load is inversely
proportional to the notch size.
Abstract: This paper presents a 3D guidance scheme for
Unmanned Aerial Vehicles (UAVs). The proposed guidance scheme
is based on the sliding mode approach using nonlinear sliding
manifolds. Generalized 3D kinematic equations are considered
here during the design process to cater for the coupling between
longitudinal and lateral motions. Sliding mode based guidance
scheme is then derived for the multiple-input multiple-output
(MIMO) system using the proposed nonlinear manifolds. Instead of
traditional sliding surfaces, nonlinear sliding surfaces are proposed
here for performance and stability in all flight conditions. In the
reaching phase control inputs, the bang-bang terms with signum
functions are accompanied with proportional terms in order to reduce
the chattering amplitudes. The Proposed 3D guidance scheme is
implemented on a 6-degrees-of-freedom (6-dof) simulation of a UAV
and simulation results are presented here for different 3D trajectories
with and without disturbances.
Abstract: The importance of the formal specification in the
software life cycle is barely concealing to anyone. Formal
specifications use mathematical notation to describe the properties of
information system precisely, without unduly constraining the way in
how these properties are achieved. Having a correct and quality
software specification is not easy task. This study concerns with how
a group of rectifiers can communicate with each other and work to
prepare and produce a correct formal software specification. WBCS
has been implemented based mainly in the proposed supported
cooperative work model and a survey conducted on the existing Webbased
collaborative writing tools. This paper aims to assess the
feasibility of executing the web-based collaboration process using
WBCS. The purpose of conducting this test is to test the system as a
whole for functionality and fitness for use based on the evaluation
test plan.
Abstract: Among all FACTS devices, the unified power flow
controller (UPFC) is considered to be the most versatile device.
This is due to its capability to control all the transmission system
parameters (impedance, voltage magnitude, and phase angle). With
the growing interest in UPFC, the attention to develop a mathematical
model has increased. Several models were introduced for UPFC in
literature for different type of studies in power systems. In this paper
a novel comparison study between two dynamic models of UPFC
with their proposed control strategies.
Abstract: This work proposes a fuzzy methodology to support
the investment decisions. While choosing among competitive
investment projects, the methodology makes ranking of projects
using the new aggregation OWA operator – AsPOWA, presented in
the environment of possibility uncertainty. For numerical evaluation
of the weighting vector associated with the AsPOWA operator the
mathematical programming problem is constructed. On the basis of
the AsPOWA operator the projects’ group ranking maximum criteria
is constructed. The methodology also allows making the most
profitable investments into several of the project using the method
developed by the authors for discrete possibilistic bicriteria problems.
The article provides an example of the investment decision-making
that explains the work of the proposed methodology.
Abstract: Azadirachta excelsa or locally known as sentang are
frequently used as a traditional medicine by diabetes patients in
Malaysia. However, less attention has been given to their toxicity
effect. Thus, the study is an attempt to examine the protective effect
of A. excelsa on the pancreas and to determine possible toxicity
mediated by the extract. Diabetes was induced experimentally in rats
by high-fat-diet for 16 weeks followed by intraperitoneal injection of
streptozotocin at dosage of 35 mg/kg of body weight. Declination of
the fasting blood glucose level was observed after continuous
administration of A. excelsa for 14 days twice daily. This is due to the
refining structure of the pancreas. However, surprisingly, the plant
extract reduced the leukocytes, erythrocytes, hemoglobin, MCHC and
lymphocytes. In addition, the rat treated with the plant extract
exhibited increment in AST and eosinocytes level. Overall, the
finding shows that A. excelsa possesses antidiabetic activity by
improving the structure of pancreatic islet of Langerhans but
involved in ameliorating of hematology and biochemical parameters.