Abstract: Resistance spot welding process comprises of electric,
thermal and mechanical phenomenon, which makes this process
complex and highly non-linear and thus, it becomes difficult to model
it. In order to obtain good weld nugget during spot welding, hit and
trial welds are usually done which is very costly. Therefore the
numerical simulation research has been conducted to understand the
whole process. In this paper three different cases were analyzed by
varying the tip contact area and it was observed that, with the
variation of tip contact area the nugget formation at the faying
surface is affected. The tip contact area of the welding electrode
becomes large with long welding cycles. Therefore in order to
maintain consistency of nugget formation during the welding process,
the current compensation in control feedback is required. If the
contact area of the welding electrode tip is reduced, a large amount of
current flows through the faying surface, as a result of which
sputtering occurs.
Abstract: The dominant judgment for earthquake damaged reinforced concrete (RC) structures is to rebuild them with the new ones. Consequently, this paper estimates if there is chance to repair earthquake RC beams and obtain economical contribution to modern day society. Therefore, the totally damaged (damaged in shear under cyclic load) reinforced concrete (RC) beams repaired and strengthened by externally bonded carbon fibre reinforced polymer (CFRP) strips in this study. Four specimens, apart from the reference beam, were separated into two distinct groups. Two experimental beams in the first group primarily tested up to failure then appropriately repaired and strengthened with CFRP strips. Two undamaged specimens from the second group were not repaired but strengthened by the identical strengthening scheme as the first group for comparison. This study studies whether earthquake damaged RC beams that have been repaired and strengthened will validate similar strength and behavior to equally strengthened, undamaged RC beams. Accordingly, a strength correspondence according to strengthened specimens was acquired for the repaired and strengthened specimens. Test results confirmed that repair and strengthening, which were estimated in the experimental program, were effective for the specimens with the cracking patterns considered in the experimental program.
Abstract: The aged are faced with increasing risk for falls. The
aged have the easily fragile bones than others. When falls have
occurred, it is important to detect this emergency state because such
events often lead to more serious illness or even death. A
implementation of PDA system, for detection of emergency situation,
was developed using 3-axis accelerometer in this paper as follows.
The signals were acquired from the 3-axis accelerometer, and then
transmitted to the PDA through Bluetooth module. This system can
classify the human activity, and also detect the emergency state like
falls. When the fall occurs, the system generates the alarm on the
PDA. If a subject does not respond to the alarm, the system determines
whether the current situation is an emergency state or not, and then
sends some information to the emergency center in the case of urgent
situation. Three different studies were conducted on 12 experimental
subjects, with results indicating a good accuracy. The first study was
performed to detect the posture change of human daily activity. The
second study was performed to detect the correct direction of fall. The
third study was conducted to check the classification of the daily
physical activity. Each test was lasted at least 1 min. in third study.
The output of acceleration signal was compared and evaluated by
changing a various posture after attaching a 3-axis accelerometer
module on the chest. The newly developed system has some important
features such as portability, convenience and low cost. One of the
main advantages of this system is that it is available at home
healthcare environment. Another important feature lies in low cost to
manufacture device. The implemented system can detect the fall
accurately, so will be widely used in emergency situation.
Abstract: Base on extenics theory, the statistical physical and mechanical properties from laboratory experiments are used to evaluate the bearing capacity of lateritic soil foundation. The properties include water content, bulk density, liquid limit, cohesion, and so on. The matter-element and the dependent function are defined. Then the synthesis dependent degree and the final grade index are calculated. The results show that predicted outcomes can be matched with the in-situ test data, and a evaluate grade associate with bearing capacity can be deduced. The results provide guidance to assess and determine the bearing capacity grade of lateritic soil foundation.
Abstract: Mathematical models of dynamics employing exterior calculus are mathematical representations of the same unifying principle; namely, the description of a dynamic system with a characteristic differential one-form on an odd-dimensional differentiable manifold leads, by analysis with exterior calculus, to a set of differential equations and a characteristic tangent vector (vortex vector) which define transformations of the system. Using this principle, a mathematical model for economic growth is constructed by proposing a characteristic differential one-form for economic growth dynamics (analogous to the action in Hamiltonian dynamics), then generating a pair of characteristic differential equations and solving these equations for the rate of economic growth as a function of labor and capital. By contracting the characteristic differential one-form with the vortex vector, the Lagrangian for economic growth dynamics is obtained.
Abstract: We report a lithography-free approach to fabricate the
biomimetics, quasi-beehive Si nanostructures (QBSNs), on
Si-substrates. The self-assembled SiGe nanoislands via the strain
induced surface roughening (Asaro-Tiller-Grinfeld instability) during
in-situ annealing play a key role as patterned sacrifice regions for
subsequent reactive ion etching (RIE) process performed for
fabricating quasi-beehive nanostructures on Si-substrates. As the
measurements of field emission, the bare QBSNs show poor field
emission performance, resulted from the existence of the native oxide
layer which forms an insurmountable barrier for electron emission. In
order to dramatically improve the field emission characteristics, the
platinum nanopillars (Pt-NPs) were deposited on QBSNs to form
Pt-NPs/QBSNs heterostructures. The turn-on field of Pt-NPs/QBSNs
is as low as 2.29 V/μm (corresponding current density of 1 μA/cm2),
and the field enhancement factor (β-value) is significantly increased to
6067. More importantly, the uniform and continuous electrons excite
light emission, due to the surrounding filed emitters from
Pt-NPs/QBSNs, can be easily obtained. This approach does not require
an expensive photolithographic process and possesses great potential
for applications.
Abstract: The purpose of this study is to derive parameters
estimating for the Lyman–Kutcher–Burman (LKB) normal tissue
complication probability (NTCP) model using analysis of scintigraphy
assessments and quality of life (QoL) measurement questionnaires for
the parotid gland (xerostomia). In total, 31 patients with
head-and-neck (HN) cancer were enrolled. Salivary excretion factor
(SEF) and EORTC QLQ-H&N35 questionnaires datasets are used for
the NTCP modeling to describe the incidence of grade 4 xerostomia.
Assuming that n= 1, NTCP fitted parameters are given as TD50= 43.6
Gy, m= 0.18 in SEF analysis, and as TD50= 44.1 Gy, m= 0.11 in QoL
measurements, respectively. SEF and QoL datasets can validate the
Quantitative Analyses of Normal Tissue Effects in the Clinic
(QUANTEC) guidelines well, resulting in NPV-s of 100% for the both
datasets and suggests that the QUANTEC 25/20Gy gland-spared
guidelines are suitable for clinical used for the HN cohort to
effectively avoid xerostomia.
Abstract: Bicycle configuration is not as large as those of motorcycles or automobiles, while it indeed composes a complicated dynamic system. People-s requirements on comfortability, controllability and safety grow higher as the research and development technologies improve. The shock absorber affects the vehicle suspension performances enormously. The absorber takes the vibration energy and releases it at a suitable time, keeping the wheel under a proper contact condition with road surface, maintaining the vehicle chassis stability. Suspension design for mountain bicycles is more difficult than that of city bikes since it encounters dynamic variations on road and loading conditions. Riders need a stiff damper as they exert to tread on the pedals when climbing, while a soft damper when they descend downhill. Various switchable shock absorbers are proposed in markets, however riders have to manually switch them among soft, hard and lock positions. This study proposes a novel design of the bicycle shock absorber, which provides automatic smooth tuning of the damping coefficient, from a predetermined lower bound to theoretically unlimited. An automatic quick releasing valve is involved in this design so that it can release the peak pressure when the suspension fork runs into a square-wave type obstacle and prevent the chassis from damage, avoiding the rider skeleton from injury. This design achieves the automatic tuning process by innovative plunger valve and fluidic passage arrangements without any electronic devices. Theoretical modelling of the damper and spring are established in this study. Design parameters of the valves and fluidic passages are determined. Relations between design parameters and shock absorber performances are discussed in this paper. The analytical results give directions to the shock absorber manufacture.
Abstract: Data of wave height and wind speed were collected
from three existing oil fields in South China Sea – offshore
Peninsular Malaysia, Sarawak and Sabah regions. Extreme values
and other significant data were employed for analysis. The data were
recorded from 1999 until 2008. The results show that offshore
structures are susceptible to unacceptable motions initiated by wind
and waves with worst structural impacts caused by extreme wave
heights. To protect offshore structures from damage, there is a need
to quantify descriptive statistics and determine spectra envelope of
wind speed and wave height, and to ascertain the frequency content
of each spectrum for offshore structures in the South China Sea
shallow waters using measured time series. The results indicate that
the process is nonstationary; it is converted to stationary process by
first differencing the time series. For descriptive statistical analysis,
both wind speed and wave height have significant influence on the
offshore structure during the northeast monsoon with high mean wind
speed of 13.5195 knots ( = 6.3566 knots) and the high mean wave
height of 2.3597 m ( = 0.8690 m). Through observation of the
spectra, there is no clear dominant peak and the peaks fluctuate
randomly. Each wind speed spectrum and wave height spectrum has
its individual identifiable pattern. The wind speed spectrum tends to
grow gradually at the lower frequency range and increasing till it
doubles at the higher frequency range with the mean peak frequency
range of 0.4104 Hz to 0.4721 Hz, while the wave height tends to
grow drastically at the low frequency range, which then fluctuates
and decreases slightly at the high frequency range with the mean
peak frequency range of 0.2911 Hz to 0.3425 Hz.
Abstract: The uses of road map in daily activities are numerous
but it is a hassle to construct and update a road map whenever there
are changes. In Universiti Malaysia Sarawak, research on Automatic
Road Extraction (ARE) was explored to solve the difficulties in
updating road map. The research started with using Satellite Image
(SI), or in short, the ARE-SI project. A Hybrid Simple Colour Space
Segmentation & Edge Detection (Hybrid SCSS-EDGE) algorithm
was developed to extract roads automatically from satellite-taken
images. In order to extract the road network accurately, the satellite
image must be analyzed prior to the extraction process. The
characteristics of these elements are analyzed and consequently the
relationships among them are determined. In this study, the road
regions are extracted based on colour space elements and edge details
of roads. Besides, edge detection method is applied to further filter
out the non-road regions. The extracted road regions are validated by
using a segmentation method. These results are valuable for building
road map and detecting the changes of the existing road database.
The proposed Hybrid Simple Colour Space Segmentation and Edge
Detection (Hybrid SCSS-EDGE) algorithm can perform the tasks
fully automatic, where the user only needs to input a high-resolution
satellite image and wait for the result. Moreover, this system can
work on complex road network and generate the extraction result in
seconds.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.
Abstract: SQL injection on web applications is a very popular
kind of attack. There are mechanisms such as intrusion detection
systems in order to detect this attack. These strategies often rely on
techniques implemented at high layers of the application but do not
consider the low level of system calls. The problem of only
considering the high level perspective is that an attacker can
circumvent the detection tools using certain techniques such as URL
encoding. One technique currently used for detecting low-level
attacks on privileged processes is the tracing of system calls. System
calls act as a single gate to the Operating System (OS) kernel; they
allow catching the critical data at an appropriate level of detail. Our
basic assumption is that any type of application, be it a system
service, utility program or Web application, “speaks” the language of
system calls when having a conversation with the OS kernel. At this
level we can see the actual attack while it is happening. We conduct
an experiment in order to demonstrate the suitability of system call
analysis for detecting SQL injection. We are able to detect the attack.
Therefore we conclude that system calls are not only powerful in
detecting low-level attacks but that they also enable us to detect highlevel
attacks such as SQL injection.
Abstract: A new, simple and highly sensitive kinetic
spectrophotometric method was developed for the determination of
trace amounts of Ru(III) in the range of 0.06-20 ng/ml .The method
is based on the inhibitory effect of ruthenium(III) on the oxidation of
Rhodamine B by bromate in acidic and micellar medium. The
reaction was monitored spectrophotometrically by measuring the
decreasing in absorbance of Rhodamine B at 554 nm with a fixedtime
method..The limit of detection is 0.04 ng/ml Ru(III).The relative
standard deviation of 5 and 10 ng/ml Ru(III) was 2.3 and 2.7 %,
respectively. The method was applied to the determination of
ruthenium in real water samples
Abstract: This paper proposes a robot able to climb Columns.
This robot is not dependent on the diameter and material of the
columns. Some climbing robots have been designed up to now but
Koala robot was designed and fabricated for climbing columns
exclusively. Simple kinematics of climbing in the nature inspired us
to design this robot. We used two linear mechanisms to grip the
column. The gripper consists of a DC motor and a power screw
mechanism with a linear bushing as a guide. This mechanism
provides enough force to grip the column. In addition we needed an
actuator for climbing the column; hence, two pneumatic jacks were
used. All the mechanical parts were designed according to the
exerted forces and operational condition. The prototype can be
simply installed and controlled on the column by an inexperienced
operator. This robot is intended for inspection and surveillance of
pipes in oil industries and power poles in electric industries.
Abstract: In order to implement flexibility as well as survivable
capacities over passive optical network (PON), a new automatic
random fault-recovery mechanism with array-waveguide-grating
based (AWG-based) optical switch (OSW) is presented. Firstly,
wavelength-division-multiplexing and optical code-division
multiple-access (WDM/OCDMA) scheme are configured to meet the
various geographical locations requirement between optical network
unit (ONU) and optical line terminal (OLT). The AWG-base optical
switch is designed and viewed as central star-mesh topology to
prohibit/decrease the duplicated redundant elements such as fiber and
transceiver as well. Hence, by simple monitoring and routing switch
algorithm, random fault-recovery capacity is achieved over
bi-directional (up/downstream) WDM/OCDMA scheme. When error
of distribution fiber (DF) takes place or bit-error-rate (BER) is higher
than 10-9 requirement, the primary/slave AWG-based OSW are
adjusted and controlled dynamically to restore the affected ONU
groups via the other working DFs immediately.
Abstract: Stress Concentration Factors are significant in
machine design as it gives rise to localized stress when any change in
the design of surface or abrupt change in the cross section occurs.
Almost all machine components and structural members contain
some form of geometrical or microstructural discontinuities. These
discontinuities are very dangerous and lead to failure. So, it is very
much essential to analyze the stress concentration factors for critical
applications like Turbine Rotors. In this paper Finite Element
Analysis (FEA) with extremely fine mesh in the vicinity of the
blades of Steam Turbine Rotor is applied to determine stress
concentration factors. A model of Steam Turbine Rotor is shown in
Fig. 1.
Abstract: According to the theory of capital structure, this paper uses principal component analysis and linear regression analysis to study the relationship between the debt characteristics of the private listed companies in Jiangsu Province and their business performance. The results show that the average debt ratio of the 29 private listed companies selected from the sample is lower. And it is found that for the sample whose debt ratio is lower than 80%, its debt ratio is negatively related to corporate performance, while for the sample whose debt ratio is beyond 80%, the relationship of debt financing and enterprise performance shows the different trends. The conclusions reflect the drawbacks may exist that the debt ratio is relatively low and having not take full advantage of debt governance effect of the private listed companies in Jiangsu Province.
Abstract: In this paper, the Lennard -Jones potential is applied
to molecules of liquid argon as well as its vapor and platinum as solid
surface in order to perform a non-equilibrium molecular dynamics
simulation to study the microscopic aspects of liquid-vapor-solid
interactions. The channel is periodic in x and y directions and along z
direction it is bounded by atomic walls. It was found that density of
the liquids near the solid walls fluctuated greatly and that the
structure was more like a solid than a liquid. This indicates that the
interactions of solid and liquid molecules are very strong. The
resultant surface tension, liquid density and vapor density are found
to be well predicted when compared with the experimental data for
argon. Liquid and vapor densities were found to depend on the cutoff
radius which induces the use of P3M (particle-particle particle-mesh)
method which was implemented for evaluation of force and surface
tension.
Abstract: Reliable information about tool temperature
distribution is of central importance in metal cutting. In this study,
tool-chip interface temperature was determined in cutting of ST37
steel workpiece by applying HSS as the cutting tool in dry turning.
Two different approaches were implemented for temperature
measuring: an embedded thermocouple (RTD) in to the cutting tool
and infrared (IR) camera. Comparisons are made between
experimental data and results of MSC.SuperForm and FLUENT
software.
An investigation of heat generation in cutting tool was performed
by varying cutting parameters at the stable cutting tool geometry and
results were saved in a computer; then the diagrams of tool
temperature vs. various cutting parameters were obtained. The
experimental results reveal that the main factors of the increasing
cutting temperature are cutting speed (V ), feed rate ( S ) and depth
of cut ( h ), respectively. It was also determined that simultaneously
change in cutting speed and feed rate has the maximum effect on
increasing cutting temperature.
Abstract: This paper gives a novel method for improving
classification performance for cancer classification with very few
microarray Gene expression data. The method employs classification
with individual gene ranking and gene subset ranking. For selection
and classification, the proposed method uses the same classifier. The
method is applied to three publicly available cancer gene expression
datasets from Lymphoma, Liver and Leukaemia datasets. Three
different classifiers namely Support vector machines-one against all
(SVM-OAA), K nearest neighbour (KNN) and Linear Discriminant
analysis (LDA) were tested and the results indicate the improvement
in performance of SVM-OAA classifier with satisfactory results on
all the three datasets when compared with the other two classifiers.