Abstract: Films of pure tin oxide SnO2 and in presence of
antimony atoms (SnO2-Sb) deposited onto glass substrates have
shown a sufficiently high energy gap to be transparent in the visible
region, a high electrical mobility and a carrier concentration which
displays a good electrical conductivity [1]. In this work, the effects of
polycrystalline silicon substrate on the optical properties of pure and
Sb doped tin oxide is investigated.
We used the APCVD (atmospheric pressure chemical vapour
deposition) technique, which is a low-cost and simple technique,
under nitrogen ambient, for growing this material. A series of SnO2
and SnO2-Sb have been deposited onto polycrystalline silicon
substrates with different contents of antimony atoms at the same
conditions of deposition (substrate temperature, flow oxygen,
duration and nitrogen atmosphere of the reactor). The effect of the
substrate in terms of morphology and nonlinear optical properties,
mainly the reflectance, was studied. The reflectance intensity of the
device, compared to the reflectance of tin oxide films deposited
directly on glass substrate, is clearly reduced on the overall
wavelength range. It is obvious that the roughness of the poly-c
silicon plays an important role by improving the reflectance and
hence the optical parameters.
A clear shift in the minimum of the reflectance upon doping level
is observed. This minimum corresponds to strong free carrier
absorption, resulting in different plasma frequency. This effect is
followed by an increase in the reflectance depending of the antimony
doping. Applying the extended Drude theory to the combining
optical and electrical obtained results these effects are discussed.
Abstract: Wireless Mesh Networks (WMNs) are an emerging
technology for last-mile broadband access. In WMNs, similar to ad
hoc networks, each user node operates not only as a host but also as a
router. User packets are forwarded to and from an Internet-connected
gateway in multi-hop fashion. The WMNs can be integrated with
other networking technologies i.e. ad hoc networks, to implement a
smooth network extension. The meshed topology provides good
reliability and scalability, as well as low upfront investments. Despite
the recent start-up surge in WMNs, much research remains to be
done in standardizing the functional parameters of WMNs to fully
exploit their full potential. An edifice of the security concerns of
these networks is authentication of a new client joining an integrated
ad hoc network and such a scenario will require execution of a multihop
authentication technique. Our endeavor in this paper is to
introduce a secure authentication technique, with light over-heads
that can be conveniently implemented for the ad-hoc nodes forming
clients of an integrated WMN, thus facilitating their inter-operability.
Abstract: In this paper, the test purpose will be to assess
whether or not the accelerated model proposed by Eyring will be able
to translate results for the shape and scale parameters of an
underlying Weibull model, obtained under two accelerating using
conditions, to expected normal using condition results for these
parameters. The product being analyzed is a new type of insulate
fluid, and the accelerating factor is the voltage stresses applied to the
fluid at two different levels (30KV and 40KV). The normal operating
voltage is 25KV. In this case, it was possible to test the insulate fluid
at normal voltage using condition. Both results for the two
parameters of the Weibull model, obtained under normal using
condition and translated from accelerated using conditions to normal
conditions, will be compared to each other to assess the accuracy of
the Eyring model when the accelerating factor is only the voltage
stress.
Abstract: This paper presents an application of the improved
QFD method for determining the specifications of kitchen utensils
rack. By using the improved method, the subjective nature in original
QFD was reduced; particularly in defining the relationship between
customer requirement and engineering characteristics. The regression
analysis that was used for obtaining the relationship functions
between customer requirement and engineering characteristics also
accommodated the inaccurateness of the competitive assessment
results. The improved method which is represented in the form of a
mathematical model had become a formal guidance to allocate the
resource for improving the specifications of kitchen utensils rack.
The specifications obtained had led to the achievement of the highest
feasible customer satisfaction.
Abstract: The aim of this study was to trace the effects of growth environment on the behaviour of fattening pigs in the farm and outside it. Behavioral manifestations of pigs reared in pens with enriched environment (A lot, n: 22) were different from those of pigs reared in pens with arid environment (B lot, n: 17) in shelter and when the movement to be loaded. Pigs of B lot spent more time on the move (31%) compared to group A pigs (13%), and manifested more aggressive behavior when they were loaded. Salivary cortisol levels also showed high values for pigs in B lot after being removed from their growth environment, as compared to its concentration for A lot pigs. The enriched environment for pigs may determine different responses of behavior. Pigs raised in arid environment, were easier to loaded than pigs reared in enriched environment, but they responded to mixing and loading stress, through increases in cortisol concentrations and impaired behavioral manifestations.
Abstract: The Beshar River is one aquatic ecosystem,which is
affected by pollutants. This study was conducted to evaluate the
effects of human activities on the water quality of the Beshar river.
This river is approximately 190 km in length and situated at the
geographical positions of 51° 20' to 51° 48' E and 30° 18' to 30° 52'
N it is one of the most important aquatic ecosystems of Kohkiloye
and Boyerahmad province next to the city of Yasuj in southern Iran.
The Beshar river has been contaminated by industrial, agricultural
and other activities in this region such as factories, hospitals,
agricultural farms, urban surface runoff and effluent of wastewater
treatment plants. In order to evaluate the effects of these pollutants
on the quality of the Beshar river, five monitoring stations were
selected along its course. The first station is located upstream of
Yasuj near the Dehnow village; stations 2 to 4 are located east, south
and west of city; and the 5th station is located downstream of Yasuj.
Several water quality parameters were sampled. These include pH,
dissolved oxygen, biological oxygen demand (BOD), temperature,
conductivity, turbidity, total dissolved solids and discharge or flow
measurements. Water samples from the five stations were collected
and analysed to determine the following physicochemical
parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5, COD during 2008
to 2009. The study shows that the BOD5 value of station 1 is at a
minimum (1.5 ppm) and increases downstream from stations 2 to 4 to
a maximum (7.2 ppm), and then decreases at station 5. The DO
values of station 1 is a maximum (9.55 ppm), decreases downstream
to stations 2 - 4 which are at a minimum (3.4 ppm), before increasing
at station 5. The amount of BOD and TDS are highest at the 4th
station and the amount of DO is lowest at this station, marking the
4th station as more highly polluted than the other stations. The
physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Abstract: It is hard to percept the interaction process with machines when visual information is not available. In this paper, we have addressed this issue to provide interaction through visual techniques. Posture recognition is done for American Sign Language to recognize static alphabets and numbers. 3D information is exploited to obtain segmentation of hands and face using normal Gaussian distribution and depth information. Features for posture recognition are computed using statistical and geometrical properties which are translation, rotation and scale invariant. Hu-Moment as statistical features and; circularity and rectangularity as geometrical features are incorporated to build the feature vectors. These feature vectors are used to train SVM for classification that recognizes static alphabets and numbers. For the alphabets, curvature analysis is carried out to reduce the misclassifications. The experimental results show that proposed system recognizes posture symbols by achieving recognition rate of 98.65% and 98.6% for ASL alphabets and numbers respectively.
Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: This paper considers the problem of scheduling maintenance actions for identical aircraft gas turbine engines. Each one of the turbines consists of parts which frequently require replacement. A finite inventory of spare parts is available and all parts are ready for replacement at any time. The inventory consists of both new and refurbished parts. Hence, these parts have different field lives. The goal is to find a replacement part sequencing that maximizes the time that the aircraft will keep functioning before the inventory is replenished. The problem is formulated as an identical parallel machine scheduling problem where the minimum completion time has to be maximized. Two models have been developed. The first one is an optimization model which is based on a 0-1 linear programming formulation, while the second one is an approximate procedure which consists in decomposing the problem into several two-machine subproblems. Each subproblem is optimally solved using the first model. Both models have been implemented using Lingo and have been tested on two sets of randomly generated data with up to 150 parts and 10 turbines. Experimental results show that the optimization model is able to solve only instances with no more than 4 turbines, while the decomposition procedure often provides near-optimal solutions within a maximum CPU time of 3 seconds.
Abstract: The aim of this work was to study the in vitro effects
of δ-lactam 1 and its 4-chlorophenyl derivative 2, on the proliferative
responses of human lymphocytes and Th1 and Th2 cytokine
secretion. The possible protective role of vitamin E on intracellular
stress oxidative induced by these compounds was also investigated.
Peripheral blood lymphocytes were isolated using differential
centrifugation on a density gradient of Histopaque. They were
cultured with mitogen concanavalin A, vitamin E (10 μM) and with
different concentrations of the compounds 1 and 2 (0.1 to 10 μM).
Proliferation (MTT assay), IL-2, INFγ and IL-4 (Elisa kits),
intracellular superoxide anion were determined. 1 and 2 were
immunostimulant and increased cytokine secretion with a shift away
from Th1 response to Th2. These properties were however
accompanied by an increase in intracellular oxidative stress. The
presence of vitamin E exhibited protective effects by reducing δ-
lactam-induced superoxide anion generation in lymphocytes.
Abstract: This paper presents the experimental results on effect of applied voltage stress frequency to the occurrence of electrical treeing in 22 kV cross linked polyethylene (XLPE) insulated cable.Hallow disk of XLPE insulating material with thickness 5 mm taken from unused high voltage cable was used as the specimen in this study. Stainless steel needle was inserted gradually into the specimen to give a tip to earth plane electrode separation of 2.50.2 mm at elevated temperature 105-110°C. The specimen was then annealed for 5 minute to minimize any mechanical stress build up around the needle-plane region before it was cooled down to room temperature. Each specimen were subjected to the same applied voltage stress level at 8 kV AC rms, with various frequency, 50, 100, 500, 1000 and 2000 Hz. Initiation time, propagation speed and pattern of electrical treeing were examined in order to study the effect of applied voltage stress frequency. By the experimental results, initial time of visible treeing decreases with increasing in applied voltage frequency. Also, obviously, propagation speed of electrical treeing increases with increasing in applied voltage frequency.Furthermore, two types of electrical treeing, bush-like and branch-like treeing were observed.The experimental results confirmed the effect of voltage stress frequency as well.
Abstract: Image watermarking has proven to be quite an
efficient tool for the purpose of copyright protection and
authentication over the last few years. In this paper, a novel image
watermarking technique in the wavelet domain is suggested and
tested. To achieve more security and robustness, the proposed
techniques relies on using two nested watermarks that are embedded
into the image to be watermarked. A primary watermark in form of a
PN sequence is first embedded into an image (the secondary
watermark) before being embedded into the host image. The
technique is implemented using Daubechies mother wavelets where
an arbitrary embedding factor α is introduced to improve the
invisibility and robustness. The proposed technique has been applied
on several gray scale images where a PSNR of about 60 dB was
achieved.
Abstract: Oral health is particular important to the hospitalized
patients with chronic schizophrenia for an extreme high potential of the respiratory infections. Due to the degeneration of physical capability, patients of this kind typically fall dependent in the activity of daily living (ADL). A very high percentage of patients had dental
problems of which mostly could be easily avoid by easy regular tooth brushing. Purpose of the project is to develop a mechanism in helping the schizophrenia patients in rebuilding a tooth-cleaning habit. The
project observed and evaluated the tooth-cleaning behavior of 100
male patients in a psychiatric hospital, and found the majority of them
ignored such an activity in a three-month period of time. In the meantime, the primary care-givers were not aware or not convinced
the importance of such a need of dental hygiene, and thus few if any
tooth cleaning training or knowledge on dental hygiene were given to
the patients. The project then developed a program based on the numerous observations and discussions. The improvement program
included patients- group education, care-givers- training, and a
tool-kit for tooth-brush holding was erected. The project launched
with some incentive package. The outcomes were encouraging with
87% of the patients had rebuilt their tooth-brushing habits against
previous 22%, and the tooth cleaning kits were 100% kept against 22%
in the past. This project had significantly improved the oral health of
the patients. The project, included the procedure and the tool-kit
holder specific for this purpose, was a good examples for psychiatric
hospitals.
Abstract: This paper presents features that characterize power
quality disturbances from recorded voltage waveforms using wavelet
transform. The discrete wavelet transform has been used to detect
and analyze power quality disturbances. The disturbances of interest
include sag, swell, outage and transient. A power system network has
been simulated by Electromagnetic Transients Program. Voltage
waveforms at strategic points have been obtained for analysis, which
includes different power quality disturbances. Then wavelet has been
chosen to perform feature extraction. The outputs of the feature
extraction are the wavelet coefficients representing the power quality
disturbance signal. Wavelet coefficients at different levels reveal the
time localizing information about the variation of the signal.
Abstract: In this paper motion analysis on a winding
stair-climbing is investigated using our proposed rotational arm type
of robotic wheelchair. For now, the robotic wheelchair is operated in
an open mode to climb winding stairs by a dynamic turning, therefore,
the dynamics model is required to ensure a passenger-s safety.
Equations of motion based on the skid-steering analysis are developed
for the trajectory planning and motion analysis on climbing winding
stairs. Since the robotic wheelchair must climb a winding staircase
stably, the winding trajectory becomes a constraint equation to be
followed, and the Baumgarte-s method is used to solve for the
constrained dynamics equations. Experimental results validate the
behavior of the prototype as it climbs a winding stair.
Abstract: Solar energy has a major role in renewable energy
resources. Solar Cell as a basement of solar system has attracted lots
of research. To conduct a study about solar energy system, an
authenticated model is required. Diode base PV models are widely
used by researchers. These models are classified based on the number
of diodes used in them. Single and two-diode models are well
studied. Single-diode models may have two, three or four elements.
In this study, these solar cell models are examined and the simulation
results are compared to each other. All PV models are re-designed in
the Matlab/Simulink software and they examined by certain test
conditions and parameters. This paper provides comparative studies
of these models and it tries to compare the simulation results with
manufacturer-s data sheet to investigate model validity and accuracy.
The results show a four- element single-diode model is accurate and
has moderate complexity in contrast to the two-diode model with
higher complexity and accuracy
Abstract: In this paper, a novel wave equation for electromagnetic
waves in a medium having anisotropic permittivity has been derived
with the help of Maxwell-s curl equations. The x and y components
of the Maxwell-s equations are written with the permittivity () being
a 3 × 3 symmetric matrix. These equations are solved for Ex , Ey,
Hx, Hy in terms of Ez, Hz, and the partial derivatives. The Z
components of the Maxwell-s curl are then used to arrive to the
generalized Helmholtz equations for Ez and Hz.
Abstract: The main objectives of this study are to inspect and
identify any damage of jaimusi highway prestressed concrete bridge
after repair and strengthening of damaged structural members and to
evaluate the performance of the bridge structural members by
adopting static load test. Inspection program after repair and
strengthening includes identifying and evaluating the structural
members of bridge such as T-shape cantilever structure, hanging
beams, corbels, external tendons, anchor beams, sticking steel plate,
and piers. The results of inspection show that the overall state of the
bridge structural member after repair and strengthening is good. The
results of rebound test of concrete strength show that the average
strength of concrete is 46.31Mpa. Whereas, the average value of
concrete strength of anchor beam is 49.82Mpa. According to the
results of static load test, the experimental values are less than
theoretical values of internal forces, deflection, and strain, indicating
that the stiffness of the experimental structure, overall deformation
and integrity satisfy the designed standard and the working
performance is good, and the undertaking capacity has a certain
surplus. There is not visible change in the length and width of cracks
and there are not new cracks under experimental load.
Abstract: Environment today is featured with aging population,
increasing prevalence of chronic disease and complex of medical
treatment. Safe use of pharmaceutics relied very much on the efforts
made by both the health- related organizations and as well as the
government agencies. As far as the specialization concern in providing
health services to the patients, the government actively issued and
implemented the divisions of medical treatment and pharmaceutical to
improve the quality of care and to reduce medication errors and ensure
public health. Pharmaceutical sub-sector policy has been implemented
for 13 years. This study attempts to explore the factors that affect the
patients- behavior intention of refilling a prescription from a NHIB
pharmacy. Samples were those patients refilling their prescriptions
with the case NHIB pharmacies. A self-administered questionnaire
was used to collect respondents- information while the patients or
family members visit the pharmacy for the refilling. 1,200
questionnaires were dispatched in 37 pharmacies that randomly
selected from Pingtung City, Dongkang, Chaozhou, Hengchun areas.
732 responses were gained with 604 valid samples for further analyses.
Results of data analyses indicated that respondents- attitude,
subjective norm, perceived behavior control and behavior intentions
toward refilling behavior varied from some demographic variables to
another. This research also suggested adding actual behavior, either by
a self-report or observed, into the research.
Abstract: Yam starch obtained from the water yam (munlued)
by the wet milling process was studied for some physicochemical
properties. Yam starch film was prepared by casting using glycerol as
a plasticizer. The effect of different glycerol (1.30, 1.65 and
2.00g/100g of filmogenic solution) and starch concentrations (3.30,
3.65 and 4.00g /100g of filmogenic solution) were evaluated on some
characteristics of the film. The temperature for obtaining the
gelatinized starch solution was 70-80°C and then dried at 45°C for 4
hours. The resulting starch from munlued granular morphology was
triangular and the average size of the granule was 26.68 μm. The
amylose content by colorimetric method was 26 % and the gelatinize
temperature was 70-80°C. The appearance of the film was smooth,
transparent, and glossy with average moisture content of 25.96% and
thickness of 0.01mm. Puncture deformation and flexibility increased
with glycerol content. The starch and glycerol concentration were a
significant factor of the yam starch film characteristics. Yam starch
film can be described as a biofilm providing many applications and
developments with the advantage of biodegradability.