Abstract: In the present study, two TRIP-assisted steels were designated as A (having no Cr and Cu content) and B (having higher Ni, Cr and Cu content) heat treated under different conditions, and the correlation between its heat treatment, microstructure and properties were investigated. Micro structural examination was carried out by optical microscope and scanning electron microscope after electrolytic etching. Non-destructive electrochemical and ultrasonic testing on two TRIP-assisted steels was used to find out corrosion and mechanical properties of different alter microstructure phase’s steels. Furthermore, micro structural studies accompanied by the evaluation of mechanical properties revealed that steels having martensite phases with higher corrosive and hardness value were less sound velocity and also steel’s microstructure having finer grains that was more grain boundary was less corrosion resistance. Steel containing more Cu, Ni and Cr was less corrosive compared to other steels having same processing or microstructure.
Abstract: The objective of the present study was to evaluate the novel nanomagnetic beads based–latex agglutination assay (NMB-LAT) as a simple test for diagnosis of S. haematobium as well as standardize the novel nanomagnetic beads based –ELISA (NMB-ELISA). According to urine examination this study included 85 S. haematobium infected patients, 30 other parasites infected patients and 25 negative control samples. The sensitivity of novel NMB-LAT was 82.4% versus 96.5% and 88.2% for NMB-ELISA and currently used sandwich ELISA respectively. The specificity of NMB-LAT was 83.6% versus 96.3% and 87.3% for NMB-ELISA and currently used sandwich ELISA respectively. In conclusion, the novel NMB-ELISA is a valuable applicable diagnostic technique for diagnosis of human schistosomiasis haematobium. The novel NMB-ELISA assay is a suitable applicable diagnostic method in field survey especially when followed by ELISA as a confirmatory test in query false negative results. Trials are required to increase the sensitivity and specificity of NMB-ELISA assay.
Abstract: The controller is used to improve the dynamic performance of DC-DC converter by achieving a robust output voltage against load disturbances. This paper presents the performance of PI and Fuzzy controller for a phase- shifted zero-voltage switched full-bridge PWM (ZVS FB- PWM) converters with a closed loop control. The proposed converter is regulated with minimum overshoot and good stability. In this paper phase-shift control method is used as an effective tool to reduce switching losses and duty cycle losses. A 1kW/100KHz dc/dc converter is simulated and analyzed using MATLAB. The circuit is simulated for static and dynamic load (DC motor). It has been observed that performance of converter with fuzzy controller is better than that of PI controller. An efficiency comparison of the converter with a reported topology has also been carried out.
Abstract: Microarrays are made it possible to simultaneously monitor the expression profiles of thousands of genes under various experimental conditions. It is used to identify the co-expressed genes in specific cells or tissues that are actively used to make proteins. This method is used to analysis the gene expression, an important task in bioinformatics research. Cluster analysis of gene expression data has proved to be a useful tool for identifying co-expressed genes, biologically relevant groupings of genes and samples. In this work K-Means algorithms has been applied for clustering of Gene Expression Data. Further, rough set based Quick reduct algorithm has been applied for each cluster in order to select the most similar genes having high correlation. Then the ACV measure is used to evaluate the refined clusters and classification is used to evaluate the proposed method. They could identify compact clusters with feature selection method used to genes are selected.
Abstract: Sea level rise threatens to increase the impact of future
storms and hurricanes on coastal communities. Accurate sea level
change prediction and supplement is an important task in determining
constructions and human activities in coastal and oceanic areas. In
this study, support vector machines (SVM) is proposed to predict
daily tidal levels along the Jeddah Coast, Saudi Arabia. The optimal
parameter values of kernel function are determined using a genetic
algorithm. The SVM results are compared with the field data and
with back propagation (BP). Among the models, the SVM is superior
to BPNN and has better generalization performance.
Abstract: In recent years, a reconstruction project for sewer
pipelines has been progressing in Japan with the aim of renewing old
sewer culverts. However, it is difficult to secure a sufficient base area
for shafts in an urban area because many streets are narrow with a
complex layout. As a result, construction in such urban areas is
generally very demanding.
In urban areas, there is a strong requirement for a safe, reliable and
economical construction method that does not disturb the public’s
daily life and urban activities. With this in mind, we developed a new
construction method called the “shield switching type micro-tunneling
method,” which integrates the micro-tunneling method and shield
method.
In this method, pipeline is constructed first for sections that are
gently curved or straight using the economical micro-tunneling
method, and then the method is switched to the shield method for
sections with a sharp curve or a series of curves without establishing
an intermediate shaft.
This paper provides the information, features and construction
examples of this newly developed method.
Abstract: By planning this experimental work to investigate the effect of zeolitic waste on rheological and technological properties of self-compacting fiber reinforced concrete, we had an intention to draw attention to the environmental factor. Large amount of zeolitic waste, as secondary raw materials are not in use properly and large amount of it is collected without a clear view of its usage in future. The principal aim of this work is to assure, that zeolitic waste admixture takes positive effect to the self-compacting fiber reinforced concrete mixes stability, flowability and other properties by using the experimental research methods. In addition to that a research on cement and zeolitic waste mortars were implemented to clarify the effect of zeolitic waste on properties of cement paste and stone. Primary studies indicates that zeolitic waste characterizes clear pozzolanic behavior, do not deteriorate and in some cases ensure positive rheological and mechanical characteristics of self-compacting concrete mixes.
Abstract: Silica fume, also known as microsilica (MS) or
condensed silica fume is a by-product of the production of silicon
metal or ferrosilicon alloys. Silica fume is one of the most effective
pozzolanic additives which could be used for ultrahigh performance
and other types of concrete. Despite the fact, however is not entirely
clear, which amount of silica fume is most optimal for UHPC. Main
objective of this experiment was to find optimal amount of silica
fume for UHPC with and without thermal treatment, when different
amount of quartz powder is substituted by silica fume. In this work
were investigated four different composition of UHPC with different
amount of silica fume. Silica fume were added 0, 10, 15 and 20% of
cement (by weight) to UHPC mixture. Optimal amount of silica fume
was determined by slump, viscosity, qualitative and quantitative
XRD analysis and compression strength tests methods.
Abstract: Thewake flow behind two yawed side-by-sidecircular
cylinders is investigated using athree-dimensional vorticity probe.
Four yaw angles (α), namely, 0°, 15°, 30° and 45° and twocylinder
spacing ratios T*
of 1.7 and 3.0 were tested. For T*
= 3.0, there exist
two vortex streets and the cylinders behave as independent and
isolated ones. The maximum contour value of the coherent streamwise
vorticity ~* ωx
is only about 10% of that of the spanwise vorticity ~* ωz
.
With the increase of α,
~* ωx
increases whereas ~* ωz
decreases. At α =
45°, ~* ωx
is about 67% of ~* ωz
.For T* = 1.7, only a single peak is
detected in the energy spectrum. The spanwise vorticity contours have
an organized pattern only at α = 0°. The maximum coherent vorticity
contours of ~* ω x
and ~* ωz
for T*
= 1.7 are about 30% and 7% of those
for T*
= 3.0.The independence principle (IP)in terms of Strouhal
numbers is applicable in both wakes when α< 40°.
Abstract: A design problem of non-uniform circular antenna arrays for maximum reduction of both the side lobe level (SLL) and first null beam width (FNBW) is dealt with. This problem is modeled as a simple optimization problem. The method of Firefly algorithm (FFA) is used to determine an optimal set of current excitation weights and antenna inter-element separations that provide radiation pattern with maximum SLL reduction and much improvement on FNBW as well. Circular array antenna laid on x-y plane is assumed. FFA is applied on circular arrays of 8-, 10-, and 12- elements. Various simulation results are presented and hence performances of side lobe and FNBW are analyzed. Experimental results show considerable reductions of both the SLL and FNBW with respect to those of the uniform case and some standard algorithms GA, PSO and SA applied to the same problem.
Abstract: In Line start permanent magnet synchronous motor, eccentricity is a common fault that can make it necessary to remove the motor from the production line. However, because the motor may be inaccessible, diagnosing the fault is not easy. This paper presents an FEM that identifies different models, static eccentricity, dynamic eccentricity, and mixed eccentricity, at no load and full load. The method overcomes the difficulty of applying FEMs to transient behavior. It simulates motor speed, torque and flux density distribution along the air gap for SE,DE, and ME. This paper represents the various effects of different eccentricitiestypes on the transient performance.
Abstract: Compatibility between sulfonated acetone- formalehyde superplasticizer (SAF) and copolymer-based grinding aids (GA) were studied by fluidity, Zeta potential, setting time of cement pasts, initial slump and slump flow of concrete and compressive strength of concrete. ESEM, MIP, and XRD were used to investigate the changing of microstructure of interior concrete. The results indicated that GA could noticeably enhance the dispersion ability of SAF. It was found that better fluidity and slump-keeping ability of cement paste were obtained in the case of GA. In addition, GA together with SAF had a certain retardation effect on hydration of cement paste. With increasing of the GA dosage, the dispersion ability and retardation effect of admixture increased. The compressive strength of the sample made with SAF and GA after 28 days was higher than that of the control sample made only with SAF. The initial slump and slump flow of concrete increased by 10.0% and 22.9%, respectively, while 0.09 wt.% GA was used. XRD examination indicated that new products were not found in the case of GA. In addition, more dense arrangement of hydrates and lower porosity of the specimen were observed by ESEM and MIP, which contributed to higher compressive strength.
Abstract: An experimental study was conducted to investigate the effect of hooked-end steel fibers on the flexural behavior of normal and high strength concrete matrices. The fibers content appropriate for the concrete matrices investigated was also determined based on flexural tests on standard prisms. Parameters investigated include: matrix compressive strength ranging from 45 MPa to 70 MPa, corresponding to normal and high strength concrete matrices respectively; fibers volume fraction including 0, 0.5%, 0.76% and 1%, equivalent to 0, 40, 60, and 80 kg/m3 of hooked-end steel fibers respectively. Test results indicated that flexural strength and toughness of normal and high strength concrete matrices were significantly improved with the increase in the fibers content added; whereas a slight improvement in compressive strength was observed for the same matrices. Furthermore, the test results indicated that the effect of increasing the fibers content was more pronounced on increasing the flexural strength of high strength concrete than that of normal concrete.
Abstract: In this research, the capability of neural networks in
modeling and learning complicated and nonlinear relations has been
used to develop a model for the prediction of changes in the diameter
of bubbles in pool boiling distilled water. The input parameters used
in the development of this network include element temperature, heat
flux, and retention time of bubbles. The test data obtained from the
experiment of the pool boiling of distilled water, and the
measurement of the bubbles form on the cylindrical element. The
model was developed based on training algorithm, which is
typologically of back-propagation type. Considering the correlation
coefficient obtained from this model is 0.9633. This shows that this
model can be trusted for the simulation and modeling of the size of
bubble and thermal transfer of boiling.
Abstract: In this research, the changes in bubbles diameter and
number that may occur due to the change in heat flux of pure water
during pool boiling process. For this purpose, test equipment was
designed and developed to collect test data. The bubbles were graded
using Caliper Screen software. To calculate the growth and
nucleation rates of bubbles under different fluxes, population balance
model was employed. The results show that the increase in heat flux
from q=20 kw/m2 to q= 102 kw/m2 raised the growth and nucleation
rates of bubbles.
Abstract: In this study, two kinds of nondestructive evaluation
(NDE) techniques (rebound hardness and ultrasonic pulse velocity
methods) are investigated for the effective maintenance of underwater
concrete structures. A new methodology to estimate the underwater
concrete strengths more effectively, named “artificial neural network
(ANN) – based concrete strength estimation with the combination of
rebound hardness and ultrasonic pulse velocity methods” is proposed
and verified throughout a series of experimental works.
Abstract: Service quality is the highest requirement by users,
especially for the service in electronic government. During the past
decades, it has become a major area of academic investigation.
Considering this issue, there are a lot of researches that evaluated the
dimensions and e-service contexts. This study also identified the
dimensions of service quality, but focuses on a new concept and
provides a new methodology in developing measurement scales of
e-service quality such as information quality, service quality and
organization quality. Finally, this study will suggest a key factor to
evaluate e-government service quality better.
Abstract: The efficiency of heavy metals removal from sewage
sludge in bioleaching processes with heterotrophic, chemoautotrophic
(sulphur-oxidizing) sludge cenoses and chemical leaching (in
distilled water, weakly acidic or alkaline medium) was compared.
The efficacy of heavy metals removal from sewage sludge varies
from 83 % (Zn) up to 14 % (Cr) and follows the order: Zn > Mn > Cu
> Ni > Co > Pb > Cr. The advantages of metals bioleaching process
at heterotrophic metabolism were shown. A new process for
bioconversation of sewage sludge into fertilizer at middle
temperatures after partial heavy metals removal was developed. This
process is based on enhancing vital ability of heterotrophic
microorganisms by adding easily metabolized nutrients and synthesis
of metabolites by growing sludge cenoses. These metabolites possess
the properties of heavy metals extractants and flocculants which
provide the enhancement of sludge flocks sedimentation. The process
results in biomineral fertilizer of prolonged action with immobilized
sludge bioelements. The fertilizer satisfies the EU limits for the
sewage sludge of agricultural utilization. High efficiency of the
biomineral fertilizer obtained has been demonstrated in vegetation
experiments.
Abstract: Bone Anchored Hearing Implants (BAHI) are
routinely used in patients with conductive or mixed hearing loss, e.g.
if conventional air conduction hearing aids cannot be used. New
sound processors and new fitting software now allow the adjustment
of parameters such as loudness compression ratios or maximum
power output separately. Today it is unclear, how the choice of these
parameters influences aided speech understanding in BAHI users.
In this prospective experimental study, the effect of varying the
compression ratio and lowering the maximum power output in a
BAHI were investigated.
Twelve experienced adult subjects with a mixed hearing loss
participated in this study. Four different compression ratios (1.0; 1.3;
1.6; 2.0) were tested along with two different maximum power output
settings, resulting in a total of eight different programs. Each
participant tested each program during two weeks. A blinded Latin
square design was used to minimize bias.
For each of the eight programs, speech understanding in quiet and
in noise was assessed. For speech in quiet, the Freiburg number test
and the Freiburg monosyllabic word test at 50, 65, and 80 dB SPL
were used. For speech in noise, the Oldenburg sentence test was
administered.
Speech understanding in quiet and in noise was improved
significantly in the aided condition in any program, when compared
to the unaided condition. However, no significant differences were
found between any of the eight programs. In contrast, on a subjective
level there was a significant preference for medium compression
ratios of 1.3 to 1.6 and higher maximum power output.
Abstract: In this paper the intelligent control of full automatic car wash using a programmable logic controller (PLC) has been investigated and designed to do all steps of carwashing. The Intelligent control of full automatic carwash has the ability to identify and profile the geometrical dimensions of the vehicle chassis. Vehicle dimension identification is an important point in this control system to adjust the washing brushes position and time duration. The study also tries to design a control set for simulating and building the automatic carwash. The main purpose of the simulation is to develop criteria for designing and building this type of carwash in actual size to overcome challenges of automation. The results of this research indicate that the proposed method in process control not only increases productivity, speed, accuracy and safety but also reduce the time and cost of washing based on dynamic model of the vehicle. A laboratory prototype based on an advanced intelligent control has been built to study the validity of the design and simulation which it’s appropriate performance confirms the validity of this study.