Abstract: Based on a theoretical erbium-doped fiber amplifier
(EDFA) model, we have proposed an application of disturbance
observer(DOB) with proportional/integral/differential(PID) controller
to EDFA for minimizing gain-transient time of wavelength
-division-multiplexing (WDM) multi channels in optical amplifier in
channel add/drop networks. We have dramatically reduced the
gain-transient time to less than 30μsec by applying DOB with PID
controller to the control of amplifier gain. The proposed DOB-based
gain control algorithm for EDFA was implemented as a digital control
system using TI's DSP(TMS320C28346) chip and experimental
results of the system verify the excellent performance of the proposed
gain control methodology.
Abstract: The spectral action balance equation is an equation that
used to simulate short-crested wind-generated waves in shallow water
areas such as coastal regions and inland waters. This equation consists
of two spatial dimensions, wave direction, and wave frequency which
can be solved by finite difference method. When this equation with
dominating propagation velocity terms are discretized using central
differences, stability problems occur when the grid spacing is chosen
too coarse. In this paper, we introduce the splitting modified donorcell
scheme for avoiding stability problems and prove that it is
consistent to the modified donor-cell scheme with same accuracy. The
splitting modified donor-cell scheme was adopted to split the wave
spectral action balance equation into four one-dimensional problems,
which for each small problem obtains the independently tridiagonal
linear systems. For each smaller system can be solved by direct or
iterative methods at the same time which is very fast when performed
by a multi-cores computer.
Abstract: To successfully provide a fast FIR filter with FTT algorithms, overlapped-save algorithms can be used to lower the computational complexity and achieve the desired real-time processing. As the length of the input block increases in order to improve the efficiency, a larger volume of zero padding will greatly increase the computation length of the FFT. In this paper, we use the overlapped block digital filtering to construct a parallel structure. As long as the down-sampling (or up-sampling) factor is an exact multiple lengths of the impulse response of a FIR filter, we can process the input block by using a parallel structure and thus achieve a low-complex fast FIR filter with overlapped-save algorithms. With a long filter length, the performance and the throughput of the digital filtering system will also be greatly enhanced.
Abstract: This paper presents an integrated knowledge-based
approach to multi-scale modeling of aquatic systems, with a view to
enhancing predictive power and aiding environmental management
and policy-making. The basic phases of this approach have been
exemplified in the case of a bay in Saronicos Gulf (Attiki, Greece).
The results showed a significant problem with rising phytoplankton
blooms linked to excessive microbial growth, arisen mostly due to
increased nitrogen inflows; therefore, the nitrification/denitrification
processes of the benthic and water column sub-systems have
provided the quality variables to be monitored for assessing
environmental status. It is thereby demonstrated that the proposed
approach facilitates modeling choices and implementation option
decisions, while it provides substantial support for knowledge and
experience capitalization in long-term water management.
Abstract: Current tools for data migration between documentoriented
and relational databases have several disadvantages. We
propose a new approach for data migration between documentoriented
and relational databases. During data migration the relational
schema of the target (relational database) is automatically created
from collection of XML documents. Proposed approach is verified on
data migration between document-oriented database IBM Lotus/
Notes Domino and relational database implemented in relational
database management system (RDBMS) MySQL.
Abstract: When the profile information of an existing road is
missing or not up-to-date and the parameters of the vertical
alignment are needed for engineering analysis, the engineer has to recreate
the geometric design features of the road alignment using
collected profile data. The profile data may be collected using
traditional surveying methods, global positioning systems, or digital
imagery. This paper develops a method that estimates the parameters
of the geometric features that best characterize the existing vertical
alignments in terms of tangents and the expressions of the curve, that
may be symmetrical, asymmetrical, reverse, and complex vertical
curves. The method is implemented using an Excel-based
optimization method that minimizes the differences between the
observed profile and the profiles estimated from the equations of the
vertical curve. The method uses a 'wireframe' representation of the
profile that makes the proposed method applicable to all types of
vertical curves. A secondary contribution of this paper is to introduce
the properties of the equal-arc asymmetrical curve that has been
recently developed in the highway geometric design field.
Abstract: In this paper, real-coded genetic algorithm (RCGA) optimization technique has been applied for large-scale linear dynamic multi-input-multi-output (MIMO) system. The method is based on error minimization technique where the integral square error between the transient responses of original and reduced order models has been minimized by RCGA. The reduction procedure is simple computer oriented and the approach is comparable in quality with the other well-known reduction techniques. Also, the proposed method guarantees stability of the reduced model if the original high-order MIMO system is stable. The proposed approach of MIMO system order reduction is illustrated with the help of an example and the results are compared with the recently published other well-known reduction techniques to show its superiority.
Abstract: In ubiqutious healthcare environment, user's health data are transfered to the remote healthcare server by the user's wearable system or mobile phone. These collected user's health data should be managed and analyzed in the healthcare server, so that care giver or user can monitor user's physiological state. In this paper, we designed and developed the intelligent Healthcare Server to manage the user's health data using CDSS and ontology. Our system can analyze user's health data semantically using CDSS and ontology, and report the result of user's physiological raw data to the user and care giver.
Abstract: The primary education system in Indonesia involved the community recognized as the school committee, to take a part in the process of achieving the quality of education via the school facility performance, the low level of school committee involvement in the education system has become the issue in the development of education and reflected to the quality of education. This paper will discuss the conceptual framework and methodology for the performance of school committees within the management of school facilities in Batubara district of Indonesia. The concepts of Community based Facility Management (CbFM) and Logometrix are used as a basis to measure the school committee performance in order to address the needs of quality school management. The data will be taken from questionnaires distributed for those who work and use school facilities spread over seven sub district of Batubara, Indonesia. The result of this study is expected to provide a guide for evaluating the performance of existing school committee in improving the quality of education in Indonesia.
Abstract: To investigate effect of salt stress on Chlorophyll
fluorescence four cultivars (fong,star,chamran and kharchia) of wheat
(Triticum aestivum) plants subjected to salinity levels ( control,8,12
and 16 dsm-1 ) from one week after emergence to the end of stem
elongation under greenhouse condition . results showed that quantum
yield of photosystem II from light adopted leaves (ΦPSII),
Photochemical quenching (qP) ,quantum yield of dark adopted leaves
(fv/fm) and non photochemical quenching (NPq) were affected by
salt stress . Salinity levels affected photosynthetic rate. Star and fong
cultivars showed minimum and maximum levels of photosynthetic
rate in respectively. Minimum photosynthetic rate differences
between levels of salinity were shown in Kharchia. Shoot dry matter
of all cultivars decreased by increasing salinity levels. Results
showed that non photochemical quenching by salinity levels attribute
to the decreases in shoot dry matter.
Abstract: In this work Artificial Intelligence (AI) techniques like Fuzzy logic, Genetic Algorithms and Particle Swarm Optimization have been used to improve the performance of the Automatic Generation Control (AGC) system. Instead of applying Genetic Algorithms and Particle swarm optimization independently for optimizing the parameters of the conventional AGC with PI controller, an intelligent tuned Fuzzy logic controller (acting as the secondary controller in the AGC system) has been designed. The controller gives an improved dynamic performance for both hydrothermal and thermal-thermal power systems under a variety of operating conditions.
Abstract: Impinging jets are widely used in industrial cooling
systems for their high heat transfer characteristics at stagnation points.
However, the heat transfer characteristics are low in the downstream
direction. In order to improve the heat transfer coefficient further
downstream, investigations introducing ribs on jet-cooled flat plates
have been conducted. Most studies regarding the heat-transfer
enhancement using a rib-roughened wall have dealt with the rib pitch.
In this paper, we focused on the rib spacing and demonstrated that the
rib spacing must be more than 6 times the nozzle width to improve heat
transfer at Reynolds number Re=5.0×103 because it is necessary to
have enough space to allow reattachment of flow behind the first rib.
Abstract: In the real application of active control systems to
mitigate the response of structures subjected to sever external
excitations such as earthquake and wind induced vibrations, since the
capacity of actuators is limited then the actuators saturate. Hence, in
designing controllers for linear and nonlinear structures under sever
earthquakes, the actuator saturation should be considered as a
constraint. In this paper optimal design of active controllers for
nonlinear structures by considering the actuator saturation has been
studied. To this end a method has been proposed based on defining
an optimization problem which considers the minimizing of the
maximum displacement of the structure as objective when a limited
capacity for actuator has been used as a constraint in optimization
problem. To evaluate the effectiveness of the proposed method, a
single degree of freedom (SDF) structure with a bilinear hysteretic
behavior has been simulated under a white noise ground acceleration
of different amplitudes. Active tendon control mechanism, comprised
of pre-stressed tendons and an actuator, and extended nonlinear
Newmark method based instantaneous optimal control algorithm
have been used as active control mechanism and algorithm. To
enhance the efficiency of the controllers, the weights corresponding
to displacement, velocity, acceleration and control force in the
performance index have been found by using the Distributed Genetic
Algorithm (DGA). According to the results it has been concluded
that the proposed method has been effective in considering the
actuator saturation in designing optimal controllers for nonlinear
frames. Also it has been shown that the actuator capacity and the
average value of required control force are two important factors in
designing nonlinear controllers for considering the actuator
saturation.
Abstract: The successful use of CDMA technology is based on
the construction of large families of encoding sequences with good
correlation properties. This paper discusses PN sequence generation
based on Residue Arithmetic with an effort to improve the performance
of existing interference-limited CDMA technology for mobile
cellular systems. All spreading codes with residual number system
proposed earlier did not consider external interferences, multipath
propagation, Doppler effect etc. In literature the use of residual
arithmetic in DS-CDMA was restricted to encoding of already spread
sequence; where spreading of sequence is done by some existing
techniques. The novelty of this paper is the use of residual number
system in generation of the PN sequences which is used to spread
the message signal. The significance of cross-correlation factor in
alleviating multi-access interference is also discussed. The RNS based
PN sequence has superior performance than most of the existing
codes that are widely used in DS-CDMA applications. Simulation
results suggest that the performance of the proposed system is
superior to many existing systems.
Abstract: With the rapid expansion of city scale and the
excessive concentration of population, achieving relative equality of
extracurricular education resources and improving spatial service
performance of relevant facilities become necessary arduous tasks. In
urban space, extracurricular education facilities should offer better
service to its targeted area and promote the equality and efficiency of
education, which is accomplished by the allocation of facilities. Based
on questionnaire and survey for local students in Hangzhou City in
2009, this study classifies extracurricular education facilities in
meg-city and defines the equalization of these facilities. Then it is
suggested to establish extracurricular education facilities system
according to the development level of city and demands of local
students, and to introduce a spatial analysis method into urban
planning through the aspects of spatial distribution, travel cost and
spatial service scope. Finally, the practice of nine sub-districts of
Hangzhou is studied.
Abstract: Nowadays over-consumption of fossil energy in
buildings especially in residential buildings and also considering the
increase in populations, the crisis of energy shortage in a near future
is predictable. The recent performance of developed countries in
construction with the aim of decreasing fossil energies shows that
these countries have understood the incoming crisis and has taken
reasonable and basic actions in this regard. However, Iranian
architecture, with several thousands years of history, has acquired
and executed invaluable experiences in designing, adapting and
coordinating with the nature.
Architectural studies during the recent decades show that imitating
modern western architecture results in high energy wastage beside
the fact that it not reasonably adaptable and corresponded with the
habits and customs of people unlike the architecture in the past which
was compatible and adaptable with the climatic conditions and this
necessitates optimal using of renewable energies more than ever. This
paper studies problems of design, execution and living in today's
houses and reviews the characteristics of climatic elements paying
special attention to the performance of trombe wall and solar
greenhouse in traditional houses and offers some suggestions for
combining these two elements and a climatic strategy.
Abstract: This paper proposes view-point insensitive human
pose recognition system using neural network. Recognition system
consists of silhouette image capturing module, data driven database,
and neural network. The advantages of our system are first, it is
possible to capture multiple view-point silhouette images of 3D human
model automatically. This automatic capture module is helpful to
reduce time consuming task of database construction. Second, we
develop huge feature database to offer view-point insensitivity at pose
recognition. Third, we use neural network to recognize human pose
from multiple-view because every pose from each model have similar
feature patterns, even though each model has different appearance and
view-point. To construct database, we need to create 3D human model
using 3D manipulate tools. Contour shape is used to convert silhouette
image to feature vector of 12 degree. This extraction task is processed
semi-automatically, which benefits in that capturing images and
converting to silhouette images from the real capturing environment is
needless. We demonstrate the effectiveness of our approach with
experiments on virtual environment.
Abstract: We present a white LED-based optical wireless
communication systems for indoor ubiquitous sensor networks. Each
sensor node could access to the server through the PLC (Power Line
Communication)-Ethernet interface. The proposed system offers a
full-duplex wireless link by using different wavelengths to reduce the
inter-symbol interference between uplink and downlink. Through the
1-to-n optical wireless sensor network and PLC modem, the mobile
terminals send a temperature data to server. The data transmission
speed and distance are 115.2kbps and about 60cm, respectively.
Abstract: In this study, we used a two-stage process and
potassium hydroxide (KOH) to transform waste biomass (rice straw)
into activated carbon and then evaluated the adsorption capacity of the
waste for removing carbofuran from an aqueous solution. Activated
carbon was fast and effective for the removal of carbofuran because of
its high surface area. The native and carbofuran-loaded adsorbents
were characterized by elemental analysis. Different adsorption
parameters, such as the initial carbofuran concentration, contact time,
temperature and pH for carbofuran adsorption, were studied using a
batch system. This study demonstrates that rice straw can be very
effective in the adsorption of carbofuran from bodies of water.
Abstract: Biochemical Oxygen Demand (BOD) is a measure of
the oxygen used in bacteria mediated oxidation of organic substances
in water and wastewater. Theoretically an infinite time is required for
complete biochemical oxidation of organic matter, but the
measurement is made over 5-days at 20 0C or 3-days at 27 0C test
period with or without dilution. Researchers have worked to further
reduce the time of measurement.
The objective of this paper is to review advancement made in
BOD measurement primarily to minimize the time and negate the
measurement difficulties. Survey of literature review in four such
techniques namely BOD-BARTTM, Biosensors, Ferricyanidemediated
approach, luminous bacterial immobilized chip method.
Basic principle, method of determination, data validation and their
advantage and disadvantages have been incorporated of each of the
methods.
In the BOD-BARTTM method the time lag is calculated for the
system to change from oxidative to reductive state. BIOSENSORS
are the biological sensing element with a transducer which produces
a signal proportional to the analyte concentration. Microbial species
has its metabolic deficiencies. Co-immobilization of bacteria using
sol-gel biosensor increases the range of substrate. In ferricyanidemediated
approach, ferricyanide has been used as e-acceptor instead
of oxygen. In Luminous bacterial cells-immobilized chip method,
bacterial bioluminescence which is caused by lux genes was
observed. Physiological responses is measured and correlated to
BOD due to reduction or emission.
There is a scope to further probe into the rapid estimation of BOD.