Abstract: With continuous rise of oil price, how to develop alternative energy source has become a hot topic around the world. This study discussed the dynamic characteristics of an island power system operating under random wind speed lower than nominal wind
speeds of wind turbines. The system primarily consists of three diesel engine power generation systems, three constant-speed variable-pitch wind turbines, a small hydraulic induction generation system, and lumped static loads. Detailed models based on Matlab/Simulink were developed to cater for the dynamic behavior of the system. The results suggested this island power system can operate stably in this operational mode. This study can serve as an important reference for planning, operation, and further expansion of island power systems.
Abstract: The main goal of data mining is to extract accurate, comprehensible and interesting knowledge from databases that may be considered as large search spaces. In this paper, a new, efficient type of Genetic Algorithm (GA) called uniform two-level GA is proposed as a search strategy to discover truly interesting, high-level prediction rules, a difficult problem and relatively little researched, rather than discovering classification knowledge as usual in the literatures. The proposed method uses the advantage of uniform population method and addresses the task of generalized rule induction that can be regarded as a generalization of the task of classification. Although the task of generalized rule induction requires a lot of computations, which is usually not satisfied with the normal algorithms, it was demonstrated that this method increased the performance of GAs and rapidly found interesting rules.
Abstract: The focal spot of a high intensity focused ultrasound
transducer is small. To heat a large target volume, multiple treatment spots are required. If the power of each treatment spot is fixed, it could
results in insufficient heating of initial spots and over-heating of later ones, which is caused by the thermal diffusion. Hence, to produce a
uniform heated volume, the delivered energy of each treatment spot
should be properly adjusted. In this study, we proposed an iterative, extrapolation technique to adjust the required ultrasound energy of
each treatment spot. Three different scanning pathways were used to evaluate the performance of this technique. Results indicate that by using the proposed technique, uniform heating volume could be obtained.
Abstract: Traditional development of wireless sensor network
mote is generally based on SoC1 platform. Such method of
development faces three main drawbacks: lack of flexibility in terms
of development due to low resource and rigid architecture of SoC;
low capability of evolution and portability versus performance if
specific micro-controller architecture features are used; and the rapid
obsolescence of micro-controller comparing to the long lifetime of
power plants or any industrial installations. To overcome these
drawbacks, we have explored a new approach of development of
wireless sensor network mote using a hybrid FPGA technology. The
application of such approach is illustrated through the
implementation of an innovative wireless sensor network protocol
called OCARI.
Abstract: Verification of real-time software systems can be
expensive in terms of time and resources. Testing is the main method
of proving correctness but has been shown to be a long and time
consuming process. Everyday engineers are usually unwilling to
adopt formal approaches to correctness because of the overhead
associated with developing their knowledge of such techniques.
Performance modelling techniques allow systems to be evaluated
with respect to timing constraints. This paper describes PARTES, a
framework which guides the extraction of performance models from
programs written in an annotated subset of C.
Abstract: This paper describes the results of an extensive study
and comparison of popular hash functions SHA-1, SHA-256,
RIPEMD-160 and RIPEMD-320 with JERIM-320, a 320-bit hash
function. The compression functions of hash functions like SHA-1
and SHA-256 are designed using serial successive iteration whereas
those like RIPEMD-160 and RIPEMD-320 are designed using two
parallel lines of message processing. JERIM-320 uses four parallel
lines of message processing resulting in higher level of security than
other hash functions at comparable speed and memory requirement.
The performance evaluation of these methods has been done by using
practical implementation and also by using step computation
methods. JERIM-320 proves to be secure and ensures the integrity of
messages at a higher degree. The focus of this work is to establish
JERIM-320 as an alternative of the present day hash functions for the
fast growing internet applications.
Abstract: The present study focuses on methods allowing a convenient and quick calculation of the SIFs in order to predict the static adhesive strength of bonded joints. A new SIF calculation method is proposed, based on the stresses obtained from a FE model at a reference point located in the adhesive layer at equal distance of the free-edge and of the two interfaces. It is shown that, even limiting ourselves to the two main modes, i.e. the opening and the shearing modes, and using the values of the stresses resulting from a low detailed FE model, an efficient calculation of the peeling stress at adhesive-substrate corners can be obtained by this way. The proposed method is interesting in that it can be the basis of a prediction tool that will allow the designer to quickly evaluate the SIFs characterizing a particular application without developing a detailed analysis.
Abstract: Delivering streaming video over wireless is an
important component of many interactive multimedia applications
running on personal wireless handset devices. Such personal devices
have to be inexpensive, compact, and lightweight. But wireless
channels have a high channel bit error rate and limited bandwidth.
Delay variation of packets due to network congestion and the high bit
error rate greatly degrades the quality of video at the handheld
device. Therefore, mobile access to multimedia contents requires
video transcoding functionality at the edge of the mobile network for
interworking with heterogeneous networks and services. Therefore,
to guarantee quality of service (QoS) delivered to the mobile user, a
robust and efficient transcoding scheme should be deployed in
mobile multimedia transporting network. Hence, this paper
examines the challenges and limitations that the video transcoding
schemes in mobile multimedia transporting network face. Then
handheld resources, network conditions and content based mobile
and wireless video transcoding is proposed to provide high QoS
applications. Exceptional performance is demonstrated in the
experiment results. These experiments were designed to verify and
prove the robustness of the proposed approach. Extensive
experiments have been conducted, and the results of various video
clips with different bit rate and frame rate have been provided.
Abstract: In this paper, we studied some properties of geodesic on some open surfaces: Hyperboloid, Paraboloid and Funnel Surface. Geodesic equation in the v-Clairaut parameterization was calculated and reduced to definite integral. Some geodesics on some open surfaces as mention above were classified by Clairaut's relation.
Abstract: A self-compacting concrete (SCC) is the one that can
be placed in the form and can go through obstructions by its own
weight and without the need of vibration. Since its first development
in Japan in 1988, SCC has gained wider acceptance in Japan, Europe
and USA due to its inherent distinct advantages. Although there are
visible signs of its gradual acceptance in the North Africa through its
limited use in construction, Libya has yet to explore the feasibility
and applicability of SCC in new construction. The contributing
factors to this reluctance appear to be lack of any supportive
evidence of its suitability with local aggregates and the harsh
environmental conditions. The primary aim of this study is to explore
the feasibility of using SCC made with local aggregates of Eastern
Province of Libya by examining its basic properties characteristics.
This research consists of: (i) Development of a suitable mix for SCC
such as the effect of water to cement ratio, limestone and silica fume
that would satisfy the requirements of the plastic state; (ii) Casting of
concrete samples and testing them for compressive strength and unit
weight. Local aggregates, cement, admixtures and industrial waste
materials were used in this research.
The significance of this research lies in its attempt to provide
some performance data of SCC made in the Eastern Province of
Libya so as to draw attention to the possible use of SCC.
Abstract: The use of buffer thresholds, blocking and adequate
service strategies are well-known techniques for computer networks
traffic congestion control. This motivates the study of series queues
with blocking, feedback (service under Head of Line (HoL) priority
discipline) and finite capacity buffers with thresholds. In this paper,
the external traffic is modelled using the Poisson process and the
service times have been modelled using the exponential distribution.
We consider a three-station network with two finite buffers, for
which a set of thresholds (tm1 and tm2) is defined. This computer
network behaves as follows. A task, which finishes its service at
station B, gets sent back to station A for re-processing with
probability o. When the number of tasks in the second buffer exceeds
a threshold tm2 and the number of task in the first buffer is less than
tm1, the fed back task is served under HoL priority discipline. In
opposite case, for fed backed tasks, “no two priority services in
succession" procedure (preventing a possible overflow in the first
buffer) is applied. Using an open Markovian queuing schema with
blocking, priority feedback service and thresholds, a closed form
cost-effective analytical solution is obtained. The model of servers
linked in series is very accurate. It is derived directly from a twodimensional
state graph and a set of steady-state equations, followed
by calculations of main measures of effectiveness. Consequently,
efficient expressions of the low computational cost are determined.
Based on numerical experiments and collected results we conclude
that the proposed model with blocking, feedback and thresholds can
provide accurate performance estimates of linked in series networks.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: In this paper, the wear of high speed steel hobs during
hobbing has been studied. The wear mechanisms are strongly
influenced by the choice of cutting speed. At moderate and high
cutting speeds three major wear mechanisms were identified:
abrasion, mild adhesive and severe adhesive. The microstructure and
wear behavior of two high speed steel grades (M2 and ASP30) has
been compared. In contrast, a variation in chemical composition or
microstructure of HSS tool material generally did not change the
dominant wear mechanism. However, the tool material properties
determine the resistance against the operating wear mechanism and
consequently the tool life. The metallographic analysis and wear
measurement at the tip of hob teeth included scanning electron
microscopy and stereoscope microscopy. Roughness profilometery is
used for measuring the gear surface roughness.
Abstract: These days MANET is attracting much attention as
they are expected to gratefully influence communication between
wireless nodes. Along with this great strength, there is much more
chance of leave and being attacked by a malicious node. Due to this
reason much attention is given to the security and the private issue in
MANET. A lot of research in MANET has been doing. In this paper
we present the overview of MANET, the security issues of MANET,
IP configuration in MANET, the solution to puzzle out the security
issues and the simulation of the proposal idea. We add the method to
figure out the malicious nodes so that we can prevent the attack from
them. Nodes exchange the information about nodes to prevent DAD
attack. We can get 30% better performance than the previous
MANETConf.
Abstract: This paper considers H∞ performance for Markovian jump systems with Time-varying delays. The systems under consideration involve disturbance signal, Markovian switching and timevarying delays. By using a new Lyapunov-Krasovskii functional and a convex optimization approach, a delay-dependent stability condition in terms of linear matrix inequality (LMI) is addressed, which guarantee asymptotical stability in mean square and a prescribed H∞ performance index for the considered systems. Two numerical examples are given to illustrate the effectiveness and the less conservatism of the proposed main results. All these results are expected to be of use in the study of stochastic systems with time-varying delays.
Abstract: This paper describes Independent Component Analysis (ICA) based fixed-point algorithm for the blind separation of the convolutive mixture of speech, picked-up by a linear microphone array. The proposed algorithm extracts independent sources by non- Gaussianizing the Time-Frequency Series of Speech (TFSS) in a deflationary way. The degree of non-Gaussianization is measured by negentropy. The relative performances of algorithm under random initialization and Null beamformer (NBF) based initialization are studied. It has been found that an NBF based initial value gives speedy convergence as well as better separation performance
Abstract: The quantified residence time distribution (RTD)
provides a numerical characterization of mixing in a reactor, thus
allowing the process engineer to better understand mixing
performance of the reactor.This paper discusses computational
studies to investigate flow patterns in a two impinging streams
cyclone reactor(TISCR) . Flow in the reactor was modeled with
computational fluid dynamics (CFD). Utilizing the Eulerian-
Lagrangian approach, implemented in FLUENT (V6.3.22), particle
trajectories were obtained by solving the particle force balance
equations. From simulation results obtained at different Δts, the mean
residence time (tm) and the mean square deviation (σ2) were
calculated. a good agreement can be observed between predicted and
experimental data. Simulation results indicate that the behavior of
complex reactor systems can be predicted using the CFD technique
with minimum data requirement for validation.
Abstract: Firstly, research and development on RFID focuses on
manufacturing and retail sectors, because it can improve supply chain
efficiency. But, now a variety of field is considered the next research
area for Radio Frequency Identification (RFID). Although RFID is
infancy, RFID technology has great potential in power industry to
significantly reduce cost, and improve quality of power supply. To
complement the limitation of RFID, we adopt the WSN (Wireless
Sensor Network) technology. However, relevant experience is limited,
the challenge will be to derive requirement from business practice and
to determine whether it is possible or not. To explore this issue, we
conduct a case study on implementing power facility management
system using RFID/WSN in Korea Electric Power Corporation
(KEPCO). In this paper we describe requirement from power industry.
And we introduce design and implementation of the test bed.
Abstract: This paper presents a heuristic approach to solve the Generalized Assignment Problem (GAP) which is NP-hard. It is worth mentioning that many researches used to develop algorithms for identifying the redundant constraints and variables in linear programming model. Some of the algorithms are presented using intercept matrix of the constraints to identify redundant constraints and variables prior to the start of the solution process. Here a new heuristic approach based on the dominance property of the intercept matrix to find optimal or near optimal solution of the GAP is proposed. In this heuristic, redundant variables of the GAP are identified by applying the dominance property of the intercept matrix repeatedly. This heuristic approach is tested for 90 benchmark problems of sizes upto 4000, taken from OR-library and the results are compared with optimum solutions. Computational complexity is proved to be O(mn2) of solving GAP using this approach. The performance of our heuristic is compared with the best state-ofthe- art heuristic algorithms with respect to both the quality of the solutions. The encouraging results especially for relatively large size test problems indicate that this heuristic approach can successfully be used for finding good solutions for highly constrained NP-hard problems.
Abstract: A horizontal anaerobic digester was developed and
tested in pilot scale for Korean food waste with high water contents
(>80%). The hydrogen sulfide in the biogas was removed by a
biological desulfurization equipment integrated in the horizontal
digester. A mixer of the horizontal digester was designed to easily
remove the sediment in the bottom and scum layers on surface in the
digester. Experimental result for 120 days of operation of the pilot
plant showed a high removal efficiency of 81.2% for organic
substance and high stability during the whole operation period were
acquired. Also food waste was treated at high organic loading rates
over 4 kg•VS/m3∙day and a methane gas production rate of 0.62
m3/kg•VSremoved was accomplished.
The biological desulfurization equipment inside the horizontal
digester was proven to be an economic and effective method to reduce
the biogas desulfurization cost by removing hydrogen sulfide more
than 90% without external desulfurization equipments.