Abstract: The Bangalore City is facing the acute problem of
pollution in the atmosphere due to the heavy increase in the traffic
and developmental activities in recent years. The present study is an
attempt in the direction to assess trend of the ambient air quality
status of three stations, viz., AMCO Batteries Factory, Mysore Road,
GRAPHITE INDIA FACTORY, KHB Industrial Area, Whitefield
and Ananda Rao Circle, Gandhinagar with respect to some of the
major criteria pollutants such as Total Suspended particular matter
(SPM), Oxides of nitrogen (NOx), and Oxides of sulphur (SO2). The
sites are representative of various kinds of growths viz., commercial,
residential and industrial, prevailing in Bangalore, which are
contributing to air pollution. The concentration of Sulphur Dioxide
(SO2) at all locations showed a falling trend due to use of refined
petrol and diesel in the recent years. The concentration of Oxides of
nitrogen (NOx) showed an increasing trend but was within the
permissible limits. The concentration of the Suspended particular
matter (SPM) showed the mixed trend. The correlation between
model and observed values is found to vary from 0.4 to 0.7 for SO2,
0.45 to 0.65 for NOx and 0.4 to 0.6 for SPM. About 80% of data is
observed to fall within the error band of ±50%. Forecast test for the
best fit models showed the same trend as actual values in most of the
cases. However, the deviation observed in few cases could be
attributed to change in quality of petro products, increase in the
volume of traffic, introduction of LPG as fuel in many types of
automobiles, poor condition of roads, prevailing meteorological
conditions, etc.
Abstract: The objective of this work is to investigate the
turbulent reacting flow in a three dimensional combustor with
emphasis on the effect of inlet swirl flow through a numerical
simulation. Flow field is analyzed using the SIMPLE method which is
known as stable as well as accurate in the combustion modeling, and
the finite volume method is adopted in solving the radiative transfer
equation. In this work, the thermal and flow characteristics in a three
dimensional combustor by changing parameters such as equivalence
ratio and inlet swirl angle have investigated. As the equivalence ratio
increases, which means that more fuel is supplied due to a larger inlet
fuel velocity, the flame temperature increases and the location of
maximum temperature has moved towards downstream. In the mean
while, the existence of inlet swirl velocity makes the fuel and
combustion air more completely mixed and burnt in short distance.
Therefore, the locations of the maximum reaction rate and temperature
were shifted to forward direction compared with the case of no swirl.
Abstract: Due to the increasing and varying risks that economic units face with, derivative instruments gain substantial importance, and trading volumes of derivatives have reached very significant level. Parallel with these high trading volumes, researchers have developed many different models. Some are parametric, some are nonparametric. In this study, the aim is to analyse the success of artificial neural network in pricing of options with S&P 100 index options data. Generally, the previous studies cover the data of European type call options. This study includes not only European call option but also American call and put options and European put options. Three data sets are used to perform three different ANN models. One only includes data that are directly observed from the economic environment, i.e. strike price, spot price, interest rate, maturity, type of the contract. The others include an extra input that is not an observable data but a parameter, i.e. volatility. With these detail data, the performance of ANN in put/call dimension, American/European dimension, moneyness dimension is analyzed and whether the contribution of the volatility in neural network analysis make improvement in prediction performance or not is examined. The most striking results revealed by the study is that ANN shows better performance when pricing call options compared to put options; and the use of volatility parameter as an input does not improve the performance.
Abstract: Information is increasing in volumes; companies are overloaded with information that they may lose track in getting the intended information. It is a time consuming task to scan through each of the lengthy document. A shorter version of the document which contains only the gist information is more favourable for most information seekers. Therefore, in this paper, we implement a text summarization system to produce a summary that contains gist information of oil and gas news articles. The summarization is intended to provide important information for oil and gas companies to monitor their competitor-s behaviour in enhancing them in formulating business strategies. The system integrated statistical approach with three underlying concepts: keyword occurrences, title of the news article and location of the sentence. The generated summaries were compared with human generated summaries from an oil and gas company. Precision and recall ratio are used to evaluate the accuracy of the generated summary. Based on the experimental results, the system is able to produce an effective summary with the average recall value of 83% at the compression rate of 25%.
Abstract: Fly ash is a significant waste that is released of
thermal power plants and defined as very fine particles that are drifted upward with up taken by the flue gases due to the burning of
used coal [1]. The fly-ash is capable of removing organic
contaminants in consequence of high carbon content, a large surface area per unit volume and contained heavy metals. Therefore, fly ash
is used as an effective coagulant and adsorbent by pelletization [2, 3].
In this study, the possibility of use of fly ash taken from Turkey like low-cost adsorbent for adsorption of zinc ions found in waste
water was investigated. The fly ash taken from Turkey was pelletized with bentonite and molass to evaluate the adsorption capaticity. For
this purpose; analyses such as sieve analysis, XRD, XRF, FTIR and SEM were performed. As a result, it was seen that pellets prepared
from fly ash, bentonite and molass would be used for zinc adsorption.
Abstract: Increasing growth of information volume in the
internet causes an increasing need to develop new (semi)automatic
methods for retrieval of documents and ranking them according to
their relevance to the user query. In this paper, after a brief review
on ranking models, a new ontology based approach for ranking
HTML documents is proposed and evaluated in various
circumstances. Our approach is a combination of conceptual,
statistical and linguistic methods. This combination reserves the
precision of ranking without loosing the speed. Our approach
exploits natural language processing techniques to extract phrases
from documents and the query and doing stemming on words. Then
an ontology based conceptual method will be used to annotate
documents and expand the query. To expand a query the spread
activation algorithm is improved so that the expansion can be done
flexible and in various aspects. The annotated documents and the
expanded query will be processed to compute the relevance degree
exploiting statistical methods. The outstanding features of our
approach are (1) combining conceptual, statistical and linguistic
features of documents, (2) expanding the query with its related
concepts before comparing to documents, (3) extracting and using
both words and phrases to compute relevance degree, (4) improving
the spread activation algorithm to do the expansion based on
weighted combination of different conceptual relationships and (5)
allowing variable document vector dimensions. A ranking system
called ORank is developed to implement and test the proposed
model. The test results will be included at the end of the paper.
Abstract: The objective of the present study was to evaluate the
potential of hollow microneedles for enhancing the transdermal
delivery of Bovine Serum Albumin (MW~66,000 Da)-Fluorescein
Isothiocyanate (BSA-FITC) conjugate, a hydrophilic large molecular
compound. Moreover, the effect of different formulations was
evaluated. The series of binary mixtures composed of propylene
glycol (PG) and pH 7.4 phosphate buffer solution (PBS) was
prepared and used as a medium for BSA-FITC. The results showed
that there was no permeation of BSA-FITC solution across the
neonatal porcine skin without using hollow microneedles, whereas
the cumulative amount of BSA-FITC released at 8 h through the
neonatal porcine skin was about 60-70% when using hollow
microneedles. Furthermore, the results demonstrated that the higher
volume of PG in binary mixtures injected, the lower cumulative
amount of BSA-FITC released and release rate of BSA-FITC from
skin. These release profiles of BSA-FITC in binary mixtures were
expressed by Fick-s law of diffusion. These results suggest the
utilization of hollow microneedle to enhance transdermal delivery of
protein and provide useful information for designing an effective
hollow microneedle system.
Abstract: If price and quantity are the fundamental building
blocks of any theory of market interactions, the importance of trading
volume in understanding the behavior of financial markets is clear.
However, while many economic models of financial markets have
been developed to explain the behavior of prices -predictability,
variability, and information content- far less attention has been
devoted to explaining the behavior of trading volume. In this article,
we hope to expand our understanding of trading volume by
developing a new measure of herding behavior based on a cross
sectional dispersion of volumes betas. We apply our measure to the
Toronto stock exchange using monthly data from January 2000 to
December 2002. Our findings show that the herd phenomenon
consists of three essential components: stationary herding, intentional
herding and the feedback herding.
Abstract: Science and technology of ultrasonic is widely used in
recent years for industrial and medicinal application. The acoustical
properties of 2-mercapto substituted pyrimidines viz.,2- Mercapto-4-
(2’,4’ –dichloro phenyl) – 6-(2’ – hydroxyl -4’ –methyl-5’ –
chlorophenyl) pyrimidine and 2 –Mercapto – 4-(4’ –chloro phenyl) –
6-(2’ – hydroxyl -4’ –methyl-5’ –chlorophenyl) pyrimidine have been
investigated from the ultrasonic velocity and density measurements at
different concentration and different % in dioxane-water mixture at
305K. The adiabatic compressibility (βs), acoustic impedance (Z),
intermolecular free length (Lf), apparent molar volume(ϕv) and
relative association (RA) values have been calculated from the
experimental data of velocity and density measurement at
concentration range of 0.01- 0.000625 mol/lit and 70%,75% and 80%
dioxane water mixture. These above parameters are used to discuss
the structural and molecular interactions.
Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: In the present study, the pressure drop and laminar convection heat transfer characteristics of nanofluids in microchannel heat sink with square duct are numerically investigated. The water based nanofluids created with Al2O3 and CuO particles in four different volume fractions of 0%, 0.5%, 1%, 1.5% and 2% are used to analyze their effects on heat transfer and the pressure drop. Under the laminar, steady-state flow conditions, the finite volume method is used to solve the governing equations of heat transfer. Mixture Model is considered to simulate the nanofluid flow. For verification of used numerical method, the results obtained from numerical calculations were compared with the results in literature for both pure water and the nanofluids in different volume fractions. The distributions of the particles in base fluid are assumed to be uniform. The results are evaluated in terms of Nusselt number, the pressure drop and heat transfer enhancement. Analysis shows that the nanofluids enhance heat transfer while the Reynolds number and the volume fractions are increasing. The best overall enhancement was obtained at φ=%2 and Re=100 for CuO-water nanofluid.
Abstract: The article deals with development, design and
implementation of a mathematical model of the human respiratory
system. The model is designed in order to simulate distribution of
important intrapulmonary parameters along the bronchial tree such as
pressure amplitude, tidal volume and effect of regional mechanical
lung properties upon the efficiency of various ventilatory techniques.
Therefore exact agreement of the model structure with the lung
anatomical structure is required. The model is based on the lung
morphology and electro-acoustic analogy is used to design the
model.
Abstract: To successfully provide a fast FIR filter with FTT algorithms, overlapped-save algorithms can be used to lower the computational complexity and achieve the desired real-time processing. As the length of the input block increases in order to improve the efficiency, a larger volume of zero padding will greatly increase the computation length of the FFT. In this paper, we use the overlapped block digital filtering to construct a parallel structure. As long as the down-sampling (or up-sampling) factor is an exact multiple lengths of the impulse response of a FIR filter, we can process the input block by using a parallel structure and thus achieve a low-complex fast FIR filter with overlapped-save algorithms. With a long filter length, the performance and the throughput of the digital filtering system will also be greatly enhanced.
Abstract: Hot Mix Asphalt (HMA) is one of the most
commonest constructed asphalts in Iran and the quality control of
constructed roads with HMA have been always paid due attention by
researchers. The quality control of constructed roads with this
method is being usually carried out by measuring volumetric
parameters of HMA marshall samples. One of the important
parameters that has a critical role in changing these volumetric
parameters is “compaction temperature"; which as a result of its
changing, volumetric parameters of Marshall Samples and
subsequently constructed asphalt is encountered with variations. In
this study, considering the necessity of preservation of the
compaction temperature, the effect of various temperatures on Hot
Mix Asphalt (HMA) samples properties has been evaluated. As well,
to evaluate the effect of this parameter on different grading, two
different grading (Top coat index grading and binder index grading)
have been used and samples were compacted at 5 various
temperatures.
Abstract: Significant changes in oil and gas drilling have
emphasized the need to verify the integrity and reliability of drill
stem components. Defects are inevitable in cast components,
regardless of application; but if these defects go undetected, any
severe defect could cause down-hole failure.
One such defect is shrinkage porosity. Castings with lower level
shrinkage porosity (CB levels 1 and 2) have scattered pores and do
not occupy large volumes; so pressure testing and helium leak testing
(HLT) are sufficient for qualifying the castings. However, castings
with shrinkage porosity of CB level 3 and higher, behave erratically
under pressure testing and HLT making these techniques insufficient
for evaluating the castings- integrity.
This paper presents a case study to highlight how the radiography
technique is much more effective than pressure testing and HLT.
Abstract: Web 2.0 (social networking, blogging and online
forums) can serve as a data source for social science research because
it contains vast amount of information from many different users.
The volume of that information has been growing at a very high rate
and becoming a network of heterogeneous data; this makes things
difficult to find and is therefore not almost useful. We have proposed
a novel theoretical model for gathering and processing data from
Web 2.0, which would reflect semantic content of web pages in
better way. This article deals with the analysis part of the model and
its usage for content analysis of blogs. The introductory part of the
article describes methodology for the gathering and processing data
from blogs. The next part of the article is focused on the evaluation
and content analysis of blogs, which write about specific trend.
Abstract: Pressure driven microscale gas flow-separation has
been investigated by solving the compressible Navier-Stokes (NS)
system of equations. A two dimensional explicit finite volume (FV)
compressible flow solver has been developed using modified
advection upwind splitting methods (AUSM+) with no-slip/first
order Maxwell-s velocity slip conditions to predict the flowseparation
behavior in microdimensions. The effects of scale-factor
of the flow geometry and gas species on the microscale gas flowseparation
have been studied in this work. The intensity of flowseparation
gets reduced with the decrease in scale of the flow
geometry. In reduced dimension, flow-separation may not at all be
present under similar flow conditions compared to the larger flow
geometry. The flow-separation patterns greatly depend on the
properties of the medium under similar flow conditions.
Abstract: The peng-Robinson (PR), a cubic equation of state (EoS), is extended to polymers by using a single set of energy (A1, A2, A3) and co-volume (b) parameters per polymer fitted to experimental volume data. Excellent results for the volumetric behavior of the 11 polymer up to 2000 bar pressure are obtained. The EoS is applied to the correlation and prediction of Henry constants in polymer solutions comprising three polymer and many nonpolar and polar solvents, including supercritical gases. The correlation achieved with two adjustable parameter is satisfactory compared with the experimental data. As a result, the present work provides a simple and useful model for the prediction of Henry's constant for polymer containing systems including those containing polar, nonpolar and supercritical fluids.
Abstract: This study presents the numerical simulation of
optimum pin-fin heat sink with air impinging cooling by using
Taguchi method. 9 L ( 4 3 ) orthogonal array is selected as a plan for
the four design-parameters with three levels. The governing
equations are discretized by using the
control-volume-based-finite-difference method with a power-law
scheme on the non-uniform staggered grid. We solved the coupling of
the velocity and the pressure terms of momentum equations using
SIMPLEC algorithm. We employ the k −ε two-equations
turbulence model to describe the turbulent behavior. The parameters
studied include fin height H (35mm-45mm), inter-fin spacing a , b ,
and c (2 mm-6.4 mm), and Reynolds number ( Re = 10000- 25000).
The objective of this study is to examine the effects of the fin
spacings and fin height on the thermal resistance and to find the
optimum group by using the Taguchi method. We found that the fin
spacings from the center to the edge of the heat sink gradually
extended, and the longer the fin’s height the better the results. The
optimum group is 3 1 2 3 H a b c . In addition, the effects of parameters are
ranked by importance as a , H , c , and b .
Abstract: Discharges in hydrogen, ignited by wire explosion, with current amplitude up to 1.5 MA were investigated. Channel diameter oscillations were observed on the photostreaks. Voltage and current curves correlated with the photostreaks. At initial gas pressure of 5-35 MPa the oscillation period was proportional to square root of atomic number of the initiating wire material. These oscillations were associated with aligned magnetic and gas-kinetic pressures. At initial pressure of 80-160 MPa acoustic pressure fluctuations on the discharge chamber wall were increased up to 150 MPa and there were the growth of voltage fluctuations on the discharge gap up to 3 kV simultaneously with it. In some experiments it was observed abrupt increase in the oscillation amplitude, which can be caused by the resonance of the acoustic oscillations in discharge chamber volume and the oscillations connected with alignment of the gaskinetic pressure and the magnetic pressure, as far as frequencies of these oscillations are close to each other in accordance with the estimates and the experimental data. Resonance of different type oscillations can produce energy density increasing in the discharge channel. Thus, the appropriate initial conditions in the experiment allow to increase the energy density in the discharge channel