Abstract: Cavitation, usually known as a destructive
phenomenon, involves turbulent unsteady two-phase flow. Having
such features, cavitating flows have been turned to a challenging
topic in numerical studies and many researches are being done for
better understanding of bubbly flows and proposing solutions to
reduce its consequent destructive effects. Aeration may be regarded
as an effective protection against cavitation erosion in many
hydraulic structures, like gated tunnels. The paper concerns
numerical simulation of flow in discharge gated tunnel of a dam
using ing RNG k -ε model coupled with the volume of fluid (VOF)
method and the zone which is susceptible of cavitation inception in
the tunnel is predicted. In the second step, a vent is considered in the
mentioned zone for aeration and the numerical simulation is done
again to study the effects of aeration. The results show that aeration
is an impressively useful method to exclude cavitation in mentioned
tunnels.
Abstract: In the Lost Foam Casting process, melting point
temperature of metal, as well as volume and rate of the foam
degradation have significant effect on the mold filling pattern.
Therefore, gas generation capacity and gas gap length are two
important parameters for modeling of mold filling time of the lost
foam casting processes. In this paper, the gas gap length at the liquidfoam
interface for a low melting point (aluminum) alloy and a high
melting point (Carbon-steel) alloy are investigated by the
photography technique. Results of the photography technique
indicated, that the gas gap length and the mold filling time are
increased with increased coating thickness and density of the foam.
The Gas gap lengths measured in aluminum and Carbon-steel,
depend on the foam density, and were approximately 4-5 and 25-60
mm, respectively. By using a new system, the gas generation
capacity for the aluminum and steel was measured. The gas
generation capacity measurements indicated that gas generation in
the Aluminum and Carbon-steel lost foam casting was about 50 CC/g
and 3200 CC/g polystyrene, respectively.
Abstract: Ovshinsky initiated scientific research in the field of
amorphous and disordered materials that continues to this day. The
Ovshinsky Effect where the resistance of thin GST films is
significantly reduced upon the application of low voltage is of
fundamental importance in phase-change - random access memory
(PC-RAM) devices.GST stands for GdSbTe chalcogenide type
glasses.However, the Ovshinsky Effect is not without controversy.
Ovshinsky thought the resistance of GST films is reduced by the
redistribution of charge carriers; whereas, others at that time including
many PC-RAM researchers today argue that the GST resistance
changes because the GST amorphous state is transformed to the
crystalline state by melting, the heat supplied by external heaters. In
this controversy, quantum mechanics (QM) asserts the heat capacity of
GST films vanishes, and therefore melting cannot occur as the heat
supplied cannot be conserved by an increase in GST film
temperature.By precluding melting, QM re-opens the controversy
between the melting and charge carrier mechanisms. Supporting
analysis is presented to show that instead of increasing GST film
temperature, conservation proceeds by the QED induced creation of
photons within the GST film, the QED photons confined by TIR. QED
stands for quantum electrodynamics and TIR for total internal
reflection. The TIR confinement of QED photons is enhanced by the
fact the absorbedheat energy absorbed in the GST film is concentrated
in the TIR mode because of their high surface to volume ratio. The
QED photons having Planck energy beyond the ultraviolet produce
excitons by the photoelectric effect, the electrons and holes of which
reduce the GST film resistance.
Abstract: Stress analysis of functionally graded composite plates
composed of ceramic, functionally graded material and metal layers is
investigated using 3-D finite element method. In FGM layer, material
properties are assumed to be varied continuously in the thickness
direction according to a simple power law distribution in terms of the
volume fraction of a ceramic and metal. The 3-D finite element model
is adopted by using an 18-node solid element to analyze more
accurately the variation of material properties in the thickness
direction. Numerical results are compared for three types of materials.
In the analysis, the tensile and the compressive stresses are
summarized for various FGM thickness ratios, volume fraction
distributions, geometric parameters and mechanical loads.
Abstract: Accurate and comprehensive thermodynamic properties of pure and mixture of refrigerants are in demand by both producers and users of these materials. Information about thermodynamic properties is important initially to qualify potential candidates for working fluids in refrigeration machinery. From practical point of view, Refrigerants and refrigerant mixtures are widely used as working fluids in many industrial applications, such as refrigerators, heat pumps, and power plants The present work is devoted to evaluating seven cubic equations of state (EOS) in predicting gas and liquid phase volumetric properties of nine ozone-safe refrigerants both in super and sub-critical regions. The evaluations, in sub-critical region, show that TWU and PR EOS are capable of predicting PVT properties of refrigerants R32 within 2%, R22, R134a, R152a and R143a within 1% and R123, R124, R125, TWU and PR EOS's, from literature data are 0.5% for R22, R32, R152a, R143a, and R125, 1% for R123, R134a, and R141b, and 2% for R124. Moreover, SRK EOS predicts PVT properties of R22, R125, and R123 to within aforementioned errors. The remaining EOS's predicts volumetric properties of this class of fluids with higher errors than those above mentioned which are at most 8%.In general, the results are in favor of the preference of TWU and PR EOS over other remaining EOS's in predicting densities of all mentioned refrigerants in both super and sub critical regions. Typically, this refrigerant is known to offer advantages such as ozone depleting potential equal to zero, Global warming potential equal to 140, and no toxic.
Abstract: In this study, Friction Stir Processing (FSP) a recent grain refinement technique was employed to disperse micron-sized (2 *m) SiCp particles into aluminum alloy AA6063. The feasibility to fabricate bulk composites through FSP was analyzed and experiments were conducted at different traverse speeds and wider volumes of the specimens. Micro structural observation were carried out by employing optical microscopy test of the cross sections in both parallel and perpendicular to the tool traverse direction. Mechanical property including micro hardness was evaluated in detail at various regions on the specimen. The composites had an excellent bonding with aluminum alloy substrate and a significant increase of 30% in the micro hardness value of metal matrix composite (MMC) as to that of the base metal has observed. The observations clearly indicate that SiC particles were uniformly distributed within the aluminum matrix.
Abstract: Study is on the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. The effects of the FGM configuration are studied by studying the frequencies of FG cylindrical shells. In this case FG cylindrical shell has Nickel on its inner surface and stainless steel on its outer surface. The study is carried out based on third order shear deformation shell theory. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of configurations of the constituent materials on the frequencies. The properties are graded in the thickness direction according to the volume fraction power-law distribution. Results are presented on the frequency characteristics, the influence of the constituent various volume fractions on the frequencies.
Abstract: Titanium nitride (TiN) has been synthesized using the
sheet plasma negative ion source (SPNIS). The parameters used for
its effective synthesis has been determined from previous
experiments and studies. In this study, further enhancement of the
deposition rate of TiN synthesis and advancement of the SPNIS
operation is presented. This is primarily achieved by the addition of
Sm-Co permanent magnets and a modification of the configuration in
the TiN deposition process. The magnetic enhancement is aimed at
optimizing the sputtering rate and the sputtering yield of the process.
The Sm-Co permanent magnets are placed below the Ti target for
better sputtering by argon. The Ti target is biased from –250V to –
350V and is sputtered by Ar plasma produced at discharge current of
2.5–4A and discharge potential of 60–90V. Steel substrates of
dimensions 20x20x0.5mm3 were prepared with N2:Ar volumetric
ratios of 1:3, 1:5 and 1:10. Ocular inspection of samples exhibit
bright gold color associated with TiN. XRD characterization
confirmed the effective TiN synthesis as all samples exhibit the (200)
and (311) peaks of TiN and the non-stoichiometric Ti2N (220) facet.
Cross-sectional SEM results showed increase in the TiN deposition
rate of up to 0.35μm/min. This doubles what was previously obtained
[1]. Scanning electron micrograph results give a comparative
morphological picture of the samples. Vickers hardness results gave
the largest hardness value of 21.094GPa.
Abstract: Current trends in manufacturing are characterized by
production broadening, innovation cycle shortening, and the products
having a new shape, material and functions. The production strategy
focused on time needed change from the traditional functional
production structure to flexible manufacturing cells and lines.
Production by automated manufacturing system (AMS) is one of the
most important manufacturing philosophies in the last years. The
main goals of the project we are involved in lies on building a
laboratory in which will be located a flexible manufacturing system
consisting of at least two production machines with NC control
(milling machines, lathe). These machines will be linked to a
transport system and they will be served by industrial robots. Within
this flexible manufacturing system a station for the quality control
consisting of a camera system and rack warehouse will be also
located. The design, analysis and improvement of this manufacturing
system, specially with a special focus on the communication among
devices constitute the main aims of this paper. The key determining
factors for the manufacturing system design are: the product, the
production volume, the used machines, the disposable manpower, the
disposable infrastructure and the legislative frame for the specific
cases.
Abstract: This paper presents a CFD analysis of the flow around
a 30° inclined flat plate of infinite span. Numerical predictions have
been compared to experimental measurements, in order to assess the
potential of the finite volume code of determining the aerodynamic
forces acting on a flat plate invested by a fluid stream of infinite
extent.
Several turbulence models and spatial node distributions have
been tested and flow field characteristics in the neighborhood of the
flat plate have been numerically investigated, allowing the
development of a preliminary procedure to be used as guidance in
selecting the appropriate grid configuration and the corresponding
turbulence model for the prediction of the flow field over a twodimensional
inclined plate.
Abstract: In this work, we used the single Langmuir probe to
measure the plasma density distribution in an geometrically
asymmetric capacitive coupled plasma discharge system. Because of
the frame structure of powered electrode, the plasma density was not
homogeneous in the discharge volume. It was higher under the frame,
but lower in the centre. Finite element simulation results showed a
good agreement with the experiment results. To increase the electron
density in the central volume and improve the homogeneity of the
plasma, we added an auxiliary electrode, powered by DC voltage, in
the simulation geometry. The simulation results showed that the
auxiliary electrode could alter the potential distribution and improve
the density homogeneity effectively.
Abstract: In recent years linguistic research has turned
increasing attention to covert/overt strategies to modulate authorial
stance and positioning in scientific texts, and to the recipients'
response. This study discussed some theoretical implications of the
use of rhetoric in scientific communication and analysed qualitative
data from the authoritative The Cognitive Neurosciences III (2004)
volume. Its genre-identity, status and readability were considered, in
the social interactive context of contemporary disciplinary discourses
– in their polyphony of traditional and new, emerging genres.
Evidence was given of the ways its famous authors negotiate and
shape knowledge and research results – explicitly appraising team
work and promoting faith in the fast-paced progress of Cognitive
Neuroscience, also through experiential metaphors – by presenting a
set of examples, ordered according to their dominant rhetorical
quality.
Abstract: Natural pozzolan (NP) is one of the potential
prehistoric alternative binders in the construction industry. It has
been investigated as cement replacement in ordinary concrete by
several researchers for many purposes. Various supplementary
cementitious materials (SCMs) such as fly ash, limestone dust and
silica fume are widely used in the production of SCC; however,
limited studies to address the effect of NP on the properties of SCC
are documented. The current research is composed of different SCC
paste and concrete mixtures containing different replacement levels
of local NP as an alternative SCM. The effect of volume of paste
containing different amounts of local NP related to W/B ratio and
cement content on SCC fresh properties was assessed. The variations
in the fresh properties of SCC paste and concrete represented by
slump flow (flowability) and the flow rate were determined and
discussed. The results indicated that the flow properties of SCC paste
and concrete mixtures, at their optimized superplasticizer dosages,
were affected by the binder content of local NP and the total volume
fraction of SCC paste.
Abstract: The internet has become an attractive avenue for
global e-business, e-learning, knowledge sharing, etc. Due to
continuous increase in the volume of web content, it is not practically
possible for a user to extract information by browsing and integrating
data from a huge amount of web sources retrieved by the existing
search engines. The semantic web technology enables advancement
in information extraction by providing a suite of tools to integrate
data from different sources. To take full advantage of semantic web,
it is necessary to annotate existing web pages into semantic web
pages. This research develops a tool, named OWIE (Ontology-based
Web Information Extraction), for semantic web annotation using
domain specific ontologies. The tool automatically extracts
information from html pages with the help of pre-defined ontologies
and gives them semantic representation. Two case studies have been
conducted to analyze the accuracy of OWIE.
Abstract: Oxyleotris marmorata is considered as
undomesticated fish, and its culture occasionally faces a problem of
food deprivation. The present study aims to evaluate alteration of
hematological indices, blood chemical associated with liver function
during 4 weeks of fasting. A non-linear relationships between fasting
days and hematological parameters (red blood cell number; y = -
0.002x2 + 0.041x + 1.249; R2=0.915, P0.05), mean corpuscular
volume; y = -0.180x2 + 2.183x + 149.61; R2=0.732, P>0.05, mean
corpuscular hemoglobin; y = -0.041x2 + 0.862x + 29.864; R2=0.818,
P>0.05 and mean corpuscular hemoglobin concentration; y = -
0.044x2 + 0.711x + 21.580; R2=0.730, P>0.05) were demonstrated.
Significant change in hematocrit (Ht) during fasting period was
observed. Ht elevated sharply increase at the first weeks of fasting
period. Higher Ht also was detected during week 2-4 of fasting time.
The significant reduction of hepatosomatic index was observed (y = -
0.007x2 - 0.096x + 1.414; R2=0.968, P0.05, serum glutamic oxaloacetic transaminase;
y = 0.005x2 – 0.201x2 + 1.297x + 33.256; R2=1, P0.05). Taken together, prolonged fasting has
deleterious effects on hematological indices, liver mass and enzyme
associated in liver function. The marked adverse effects occurred
after the first week of fasting state.
Abstract: Analytical solution of the first-order and third-order
shear deformation theories are developed to study the free vibration
behavior of simply supported functionally graded plates. The
material properties of plate are assumed to be graded in the thickness
direction as a power law distribution of volume fraction of the
constituents. The governing equations of functionally graded plates
are established by applying the Hamilton's principle and are solved
by using the Navier solution method. The influence of side-tothickness
ratio and constituent of volume fraction on the natural
frequencies are studied. The results are validated with the known
data in the literature.
Abstract: Different numerical methods are employed and developed for simulating interfacial flows. A large range of applications belong to this group, e.g. two-phase flows of air bubbles in water or water drops in air. In such problems surface tension effects often play a dominant role. In this paper, various models of surface tension force for interfacial flows, the CSF, CSS, PCIL and SGIP models have been applied to simulate the motion of small air bubbles in water and the results were compared and reviewed. It has been pointed out that by using SGIP or PCIL models, we are able to simulate bubble rise and obtain results in close agreement with the experimental data.
Abstract: The aim of this study was to investigate the
effectiveness of anaerobic digestion for the treatment of wool
scouring wastes. The experiments design comprised three ratios of
waste (W) to seed(S) (W:S) of 25:75, 50:50 and 75:25, corresponding
to 1.9. 1.7 and 1.5g tCOD/g TS, respectively, with or without
chemicals addition. NH4Cl was added to the reactors as a source for
nitrogen to achieve C:N:P of 420:14:3. A cationic flocculent was
added at 0.5 and 0.75% to enhance flocculation of sludge. The results
showed that the reactors that received W:S at a ratio of 25:75
produced the largest volume of biogas. The final soluble COD
(sCOD) was below the limits for discharge to the sewer system.
Abstract: Nowadays, with the emerging of the new applications
like robot control in image processing, artificial vision for visual
servoing is a rapidly growing discipline and Human-machine
interaction plays a significant role for controlling the robot. This
paper presents a new algorithm based on spatio-temporal volumes for
visual servoing aims to control robots. In this algorithm, after
applying necessary pre-processing on video frames, a spatio-temporal
volume is constructed for each gesture and feature vector is extracted.
These volumes are then analyzed for matching in two consecutive
stages. For hand gesture recognition and classification we tested
different classifiers including k-Nearest neighbor, learning vector
quantization and back propagation neural networks. We tested the
proposed algorithm with the collected data set and results showed the
correct gesture recognition rate of 99.58 percent. We also tested the
algorithm with noisy images and algorithm showed the correct
recognition rate of 97.92 percent in noisy images.
Abstract: In the last two decades radiofrequency ablation (RFA)
has been considered a promising medical procedure for the treatment
of primary and secondary malignancies. However, the needle-based
electrodes so far developed for this kind of treatment are not suitable
for the thermal ablation of tumors located in hollow organs like
esophagus, colon or bile duct. In this work a tubular electrode
solution is presented. Numerical and experimental analyses were
performed to characterize the volume of the lesion induced. Results
show that this kind of electrode is a feasible solution and numerical
simulation might provide a tool for planning RFA procedure with
some accuracy.