Abstract: This paper considers the problem of finding low cost
chip set for a minimum cost partitioning of a large logic circuits. Chip
sets are selected from a given library. Each chip in the library has a
different price, area, and I/O pin. We propose a low cost chip set
selection algorithm. Inputs to the algorithm are a netlist and a chip
information in the library. Output is a list of chip sets satisfied with
area and maximum partitioning number and it is sorted by cost. The
algorithm finds the sorted list of chip sets from minimum cost to
maximum cost. We used MCNC benchmark circuits for experiments.
The experimental results show that all of chip sets found satisfy the
multiple partitioning constraints.
Abstract: The utilize of renewable energy sources becomes
more crucial and fascinatingly, wider application of renewable
energy devices at domestic, commercial and industrial levels is not
only affect to stronger awareness but also significantly installed
capacities. Moreover, biomass principally is in form of woods and
converts to be energy for using by humans for a long time.
Gasification is a process of conversion of solid carbonaceous fuel
into combustible gas by partial combustion. Many gasified models
have various operating conditions because the parameters kept in
each model are differentiated. This study applied the experimental
data including three inputs variables including biomass consumption;
temperature at combustion zone and ash discharge rate and gas flow
rate as only one output variable. In this paper, response surface
methods were applied for identification of the gasified system
equation suitable for experimental data. The result showed that linear
model gave superlative results.
Abstract: Experiments have been carried out at sub-critical
Reynolds number to investigate free-to-roll motions induced by
forebody and/or wings complex flow on a 30° swept back nonslender
wings-slender body-model for static and dynamic (pitch-up)
cases. For the dynamic (pitch-up) case it has been observed that roll
amplitude decreases and lag increases with increase in pitching
speed. Decrease in roll amplitude with increase in pitch rate is
attributed to low disturbing rolling moment due to weaker interaction
between forebody and wing flow components. Asymmetric forebody
vortices dominate and control the roll motion of the model in
dynamic case when non-dimensional pitch rate ≥ 1x10-2.
Effectiveness of the active control scheme utilizing rotating nose with
artificial tip perturbation is observed to be low in the angle of attack
region where the complex flow over the wings has contributions from
both forebody and wings.
Abstract: Prickly pear juice has received renewed attention with regard to the effects of processing and preservation on its sensory qualities (colour, taste, flavour, aroma, astringency, visual browning and overall acceptability). Juice was prepared by homogenizing fruit and treating the pulp with pectinase (Aspergillus niger). Juice treatments applied were sugar addition, acidification, heat-treatment, refrigeration, and freezing and thawing. Prickly pear pulp and juice had unique properties (low pH 3.88, soluble solids 3.68 oBrix and high titratable acidity 0.47). Sensory profiling and descriptive analyses revealed that non-treated juice had a bitter taste with high astringency whereas treated prickly pear was significantly sweeter. All treated juices had a good sensory acceptance with values approximating or exceeding 7. Regression analysis of the consumer sensory attributes for non-treated prickly pear juice indicated an overwhelming rejection, while treated prickly pear juice received overall acceptability. Thus, educed favourable sensory responses and may have positive implications for consumer acceptability.
Abstract: Fischer-Tropsch synthesis is one of the most
important catalytic reactions that convert the synthetic gas to light
and heavy hydrocarbons. One of the main issues is selecting the type
of reactor. The slurry bubble reactor is suitable choice for Fischer-
Tropsch synthesis because of its good qualification to transfer heat
and mass, high durability of catalyst, low cost maintenance and
repair. The more common catalysts for Fischer-Tropsch synthesis are
Iron-based and Cobalt-based catalysts, the advantage of these
catalysts on each other depends on which type of hydrocarbons we
desire to produce. In this study, Fischer-Tropsch synthesis is modeled
with Iron and Cobalt catalysts in a slurry bubble reactor considering
mass and momentum balance and the hydrodynamic relations effect
on the reactor behavior. Profiles of reactant conversion and reactant
concentration in gas and liquid phases were determined as the
functions of residence time in the reactor. The effects of temperature,
pressure, liquid velocity, reactor diameter, catalyst diameter, gasliquid
and liquid-solid mass transfer coefficients and kinetic
coefficients on the reactant conversion have been studied. With 5%
increase of liquid velocity (with Iron catalyst), H2 conversions
increase about 6% and CO conversion increase about 4%, With 8%
increase of liquid velocity (with Cobalt catalyst), H2 conversions
increase about 26% and CO conversion increase about 4%. With
20% increase of gas-liquid mass transfer coefficient (with Iron
catalyst), H2 conversions increase about 12% and CO conversion
increase about 10% and with Cobalt catalyst H2 conversions increase
about 10% and CO conversion increase about 6%. Results show that
the process is sensitive to gas-liquid mass transfer coefficient and
optimum condition operation occurs in maximum possible liquid
velocity. This velocity must be more than minimum fluidization
velocity and less than terminal velocity in such a way that avoid
catalysts particles from leaving the fluidized bed.
Abstract: Repetitive control and feedback dithering modulation
are applied to a single-phase voltage source inverter, with an aim to
eliminate harmonics and stabilize the inverter under load variations.
The proposed control and modulation scheme comprise multiple loops
of feedback, which helps improve inverter performance and
robustness. Experimental results show that the designed inverter
exhibits very low distortion at its output with THD of about 0.3%
under different load variations.
Abstract: This paper presents a robust method to detect obstacles in stereo images using shadow removal technique and color information. Stereo vision based obstacle detection is an algorithm that aims to detect and compute obstacle depth using stereo matching and disparity map. The proposed advanced method is divided into three phases, the first phase is detecting obstacles and removing shadows, the second one is matching and the last phase is depth computing. We propose a robust method for detecting obstacles in stereo images using a shadow removal technique based on color information in HIS space, at the first phase. In this paper we use Normalized Cross Correlation (NCC) function matching with a 5 × 5 window and prepare an empty matching table τ and start growing disparity components by drawing a seed s from S which is computed using canny edge detector, and adding it to τ. In this way we achieve higher performance than the previous works [2,17]. A fast stereo matching algorithm is proposed that visits only a small fraction of disparity space in order to find a semi-dense disparity map. It works by growing from a small set of correspondence seeds. The obstacle identified in phase one which appears in the disparity map of phase two enters to the third phase of depth computing. Finally, experimental results are presented to show the effectiveness of the proposed method.
Abstract: Intellectual capital measurement is a central aspect of knowledge management. The measurement and the evaluation of intangible assets play a key role in allowing an effective management of these assets as sources of competitiveness. For these reasons, managers and practitioners need conceptual and analytical tools taking into account the unique characteristics and economic significance of Intellectual Capital. Following this lead, we propose an efficiency and productivity analysis of Intellectual Capital, as a determinant factor of the company competitive advantage. The analysis is carried out by means of Data Envelopment Analysis (DEA) and Malmquist Productivity Index (MPI). These techniques identify Bests Practice companies that have accomplished competitive advantage implementing successful strategies of Intellectual Capital management, and offer to inefficient companies development paths by means of benchmarking. The proposed methodology is employed on the Biotechnology industry in the period 2007-2010.
Abstract: Nowadays there are several grid connected converter
in the grid system. These grid connected converters are generally the
converters of renewable energy sources, industrial four quadrant
drives and other converters with DC link. These converters are
connected to the grid through a three phase bridge. The standards
prescribe the maximal harmonic emission which could be easily
limited with high switching frequency. The increased switching
losses can be reduced to the half with the utilization of the wellknown
Flat-top modulation. The suggested control method is the
expansion of the Flat-top modulation with which the losses could be
also reduced to the half compared to the Flat-top modulation.
Comparing to traditional control these requirements can be
simultaneously satisfied much better with the DLF (DC Link
Floating) method.
Abstract: In this paper, an accurate theoretical analysis for the achievable average channel capacity (in the Shannon sense) per user of a hybrid cellular direct-sequence/fast frequency hopping code-division multiple-access (DS/FFH-CDMA) system operating in a Rayleigh fading environment is presented. The analysis covers the downlink operation and leads to the derivation of an exact mathematical expression between the normalized average channel capacity available to each system-s user, under simultaneous optimal power and rate adaptation and the system-s parameters, as the number of hops per bit, the processing gain applied, the number of users per cell and the received signal-tonoise power ratio over the signal bandwidth. Finally, numerical results are presented to illustrate the proposed mathematical analysis.
Abstract: This paper presents a new optimization technique based on quantum computing principles to solve a security constrained power system economic dispatch problem (SCED). The proposed technique is a population-based algorithm, which uses some quantum computing elements in coding and evolving groups of potential solutions to reach the optimum following a partially directed random approach. The SCED problem is formulated as a constrained optimization problem in a way that insures a secure-economic system operation. Real Coded Quantum-Inspired Evolution Algorithm (RQIEA) is then applied to solve the constrained optimization formulation. Simulation results of the proposed approach are compared with those reported in literature. The outcome is very encouraging and proves that RQIEA is very applicable for solving security constrained power system economic dispatch problem (SCED).
Abstract: This paper presents a hand vein authentication system
using fast spatial correlation of hand vein patterns. In order to
evaluate the system performance, a prototype was designed and a
dataset of 50 persons of different ages above 16 and of different
gender, each has 10 images per person was acquired at different
intervals, 5 images for left hand and 5 images for right hand. In
verification testing analysis, we used 3 images to represent the
templates and 2 images for testing. Each of the 2 images is matched
with the existing 3 templates. FAR of 0.02% and FRR of 3.00 %
were reported at threshold 80. The system efficiency at this threshold
was found to be 99.95%. The system can operate at a 97% genuine
acceptance rate and 99.98 % genuine reject rate, at corresponding
threshold of 80. The EER was reported as 0.25 % at threshold 77. We
verified that no similarity exists between right and left hand vein
patterns for the same person over the acquired dataset sample.
Finally, this distinct 100 hand vein patterns dataset sample can be
accessed by researchers and students upon request for testing other
methods of hand veins matching.
Abstract: The widely used Total Variation de-noising algorithm can preserve sharp edge, while removing noise. However, since fixed regularization parameter over entire image, small details and textures are often lost in the process. In this paper, we propose a modified Total Variation algorithm to better preserve smaller-scaled features. This is done by allowing an adaptive regularization parameter to control the amount of de-noising in any region of image, according to relative information of local feature scale. Experimental results demonstrate the efficient of the proposed algorithm. Compared with standard Total Variation, our algorithm can better preserve smaller-scaled features and show better performance.
Abstract: This study aimed to present the mechanical
performance evaluation of the dynamic hip screw (DHS) for
trochanteric fracture by means of finite element method. The
analyses were performed based on stainless steel and titanium
implant material definitions at various stages of bone healing and
including implant removal. The assessment of the mechanical
performance used two parameters, von Mises stress to evaluate the
strength of bone and implant and elastic strain to evaluate fracture
stability. The results show several critical aspects of dynamic hip
screw for trochanteric fracture stabilization. In the initial stage of
bone healing process, partial weight bearing should be applied to
avoid the implant failure. In the late stage of bone healing, stainless
steel implant should be removed.
Abstract: In this paper, we present an experimental testing for
a new algorithm that determines an optimal controller-s coefficients
for output variance reduction related to Linear Time Invariant (LTI)
Systems. The algorithm features simplicity in calculation, generalization
to minimal and non-minimal phase systems, and could be
configured to achieve reference tracking as well as variance reduction
after compromising with the output variance. An experiment of DCmotor
velocity control demonstrates the application of this new
algorithm in designing the controller. The results show that the
controller achieves minimum variance and reference tracking for a
preset velocity reference relying on an identified model of the motor.
Abstract: The distribution, enrichment, accumulation, and potential ecological risk of copper (Cu) in the surface sediments of northern Kaohsiung Harbor, Taiwan were investigated. Sediment samples from 12 locations of northern Kaohsiung Harbor were collected and characterized for Cu, aluminum, water content, organic matter, total nitrogen, total phosphorous, total grease and grain size. Results showed that the Cu concentrations varied from 6.9–244 mg/kg with an average of 109±66 mg/kg. The spatial distribution of Cu reveals that the Cu concentration is relatively high in the river mouth region, and gradually diminishes toward the harbor entrance region. This indicates that upstream industrial and municipal wastewater discharges along the river bank are major sources of Cu pollution. Results from the enrichment factor and geo-accumulation index analyses imply that the sediments collected from the river mouth can be characterized between moderate and moderately severe degree enrichment and between none to medium and moderate accumulation of Cu, respectively. However, results of potential ecological risk index indicate that the sediment has low ecological potential risk.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.
Abstract: Turkey has 72 % of total world boron reserves on the
basis of B2O3.Borates that is a refined form of boron minerals have a
wide range of applications. Zinc borates can be used as multifunctional
synergistic additives. The most important properties are
low solubility in water and high dehydration temperature. Zinc
borates dehydrate above 290°C and anhydrous zinc borate has
thermal resistance about 400°C. Zinc borates can be synthesized
using several methods such as hydrothermal and solid-state
processes. In this study, the solid-state method was applied between
500 and 800°C using the starting materials of ZnO and H3BO3 with
1:4 mole ratio. The reaction time was determined as 4 hours after
some preliminary experiments. After the synthesis, the crystal
structure and the morphology of the products were examined by XRay
Diffraction (XRD), Fourier Transform Infrared Spectroscopy
(FT-IR) and Raman Spectrometer. As a result the form of ZnB4O7
was synthesized with the highest crystal score at 800°C.
Abstract: Measurement of the COD of a spent caustic solution involves firstly digestion of a test sample with dichromate solution and secondly measurement of dichromate remained by titration by ferrous ammonium sulfate [FAS] to an end point. In this paper we study by a potentiometric end point with Ag/AgCl reference electrode and gold rode electrode. The potentiometric end point is sharp and easily identified especially for the samples with high turbidity and color that other methods such as colorimetric in this type of sample do not result in high precision. Because interim of titration responds quickly to potential changes within the [Cr+6/Cr+3& Fe+2/Fe+3] solution producing stable readings that is lead to accurate COD measurement. Finally results are compared with data determined using colorimetric method for standard samples. It is shown that the potentiometric end point titration with gold rode electrode can be used with equal or better facility
Abstract: The objective of this research is to calculate the
optimal inventory lot-sizing for each supplier and minimize the total
inventory cost which includes joint purchase cost of the products,
transaction cost for the suppliers, and holding cost for remaining
inventory. Genetic algorithms (GAs) are applied to the multi-product
and multi-period inventory lot-sizing problems with supplier
selection under storage space. Also a maximum storage space for the
decision maker in each period is considered. The decision maker
needs to determine what products to order in what quantities with
which suppliers in which periods. It is assumed that demand of
multiple products is known over a planning horizon. The problem is
formulated as a mixed integer programming and is solved with the
GAs. The detailed computation results are presented.