Abstract: This study was to investigate the performance of
hybrid solvents blended between primary, secondary, or tertiary
amines and piperazine (PZ) for CO2 removal from flue gas in terms
of CO2 absorption capacity and regeneration efficiency at 90 oC.
Alkanolamines used in this work were monoethanolamine (MEA),
diethanolamine (DEA), and triethanolamine (TEA). The CO2
absorption was experimentally examined under atmospheric pressure
and room temperature. The results show that MEA blend with PZ
provided the maximum CO2 absorption capacity of 0.50 mol
CO2/mol amine while TEA provided the minimum CO2 absorption
capacity of 0.30 mol CO2/mol amine. TEA was easier to regenerate
for both first cycle and second cycle with less loss of absorption
capacity. The regeneration efficiency of TEA was 95.09 and 92.89 %,
for the first and second generation cycles, respectively.
Abstract: with increasing circuits- complexity and demand to
use portable devices, power consumption is one of the most
important parameters these days. Full adders are the basic block of
many circuits. Therefore reducing power consumption in full adders
is very important in low power circuits. One of the most powerconsuming
modules in full adders is XOR/XNOR circuit. This paper
presents two new full adders based on two new logic approaches. The
proposed logic approaches use one XOR or XNOR gate to implement
a full adder cell. Therefore, delay and power will be decreased. Using
two new approaches and two XOR and XNOR gates, two new full
adders have been implemented in this paper. Simulations are carried
out by HSPICE in 0.18μm bulk technology with 1.8V supply voltage.
The results show that the ten-transistors proposed full adder has 12%
less power consumption and is 5% faster in comparison to MB12T
full adder. 9T is more efficient in area and is 24% better than similar
10T full adder in term of power consumption. The main drawback of
the proposed circuits is output threshold loss problem.
Abstract: The malfunction of thermal protection system (TPS) caused by aerodynamic heating is a latent trouble to aircraft structure safety. Accurately predicting the structure temperature field is quite important for the TPS design of hypersonic vehicle. Since Thornton’s work in 1988, the coupled method of aerodynamic heating and heat transfer has developed rapidly. However, little attention has been paid to the influence of structural deformation on aerodynamic heating and structural temperature field. In the flight, especially the long-endurance flight, the structural deformation, caused by the aerodynamic heating and temperature rise, has a direct impact on the aerodynamic heating and structural temperature field. Thus, the coupled interaction cannot be neglected. In this paper, based on the method of static aero-thermo-elasticity, considering the influence of aero-thermo-elasticity deformation, the aerodynamic heating and heat transfer coupled results of hypersonic vehicle wing model were calculated. The results show that, for the low-curvature region, such as fuselage or center-section wing, structure deformation has little effect on temperature field. However, for the stagnation region with high curvature, the coupled effect is not negligible. Thus, it is quite important for the structure temperature prediction to take into account the effect of elastic deformation. This work has laid a solid foundation for improving the prediction accuracy of the temperature distribution of aircraft structures and the evaluation capacity of structural performance.
Abstract: Distance education program is a dimension of contemporary and new education technologies. Concepts and applications in this field are the results of a series of educational demands and developments in various communication and education technologies. Distance education applications have some conceptual bases. These are creating new education opportunities, realizing work-education unity, getting democratic in education, lifelong education, tendency to individual matters, effective use of institutions, integration of technology and education, tendency to individual and social needs, taking three dimensional integration as the main principle (publishing, printed materials and face to face education), reaching maximum mass, individual and mass education integrity and education demand and financial matters balance. Economics, Business Administration and Open Education faculties, which have been giving education within Anadolu University since 1982 in Turkey, are carrying on education with nearly 1.000.000 students. The aim of this study is to determine organizational commitment levels of students who have been studying at Anadolu University Economics, Business Administration and Open Education faculties in the scope of affective, continuance and nominative commitment in Allen&Meyer model. In the study, organizational commitment of the Economics, Business Administration and Open Education faculty students, who are receiving education by means of distance education, to their faculties is dealt after introducing Anadolu University Distance Education system which gives higher education via distance education method in Turkey. In order to increase the success level of faculties it is required for students to have high level of organizational commitment to their faculties. A questionnaire has been applied by using “Organizational Commitment Scale", developed by Meyer&Allen to determine organizational commitments of Economics, Business Administration and Open Education students. Organizational commitment is dealt with as affective, continuance and nominative commitment. The questionnaire was applied face to face to randomly chosen 500 students living in Eskişehir and the data was downloaded to the computer by using SPSS program and the results were analyzed in terms of demographic features (gender, age, marital status, years of study, work and income level) of students by using frequency test, ttest and ANOVA test. As a result of these analyses, when the comments of Open Education Faculty students on levels of affective, continuance and nominative commitment to their faculties were examined, it has been revealed that continuance commitment level has the highest rate. Among the female participants; continuance commitment is high in the age range of 30-40, for normative commitment it is 17-22. However no dominant age range was defined for affective commitment. Regarding the marital status; continuance commitment average is higher among married participants; but nominative affective commitment average is higher among single participants. As to the years of study, affective and continuance commitment is higher among senior students while normative commitment is higher among junior students. Moreover; in terms of continuance, affective and normative commitment, those who do not work and have low income have higher level of all there commitment types than those who work and have relatively high income.
Abstract: The practical implementation of audio-video coupled speech recognition systems is mainly limited by the hardware complexity to integrate two radically different information capturing devices with good temporal synchronisation. In this paper, we propose a solution based on a smart CMOS image sensor in order to simplify the hardware integration difficulties. By using on-chip image processing, this smart sensor can calculate in real time the X/Y projections of the captured image. This on-chip projection reduces considerably the volume of the output data. This data-volume reduction permits a transmission of the condensed visual information via the same audio channel by using a stereophonic input available on most of the standard computation devices such as PC, PDA and mobile phones. A prototype called VMIKE (Visio-Microphone) has been designed and realised by using standard 0.35um CMOS technology. A preliminary experiment gives encouraged results. Its efficiency will be further investigated in a large variety of applications such as biometrics, speech recognition in noisy environments, and vocal control for military or disabled persons, etc.
Abstract: This paper presents the simulation of fragmentation
warhead using a hydrocode, Autodyn. The goal of this research is to
determine the lethal range of such a warhead. This study investigates
the lethal range of warheads with and without steel balls as
preformed fragments. The results from the FE simulation, i.e. initial
velocities and ejected spray angles of fragments, are further processed
using an analytical approach so as to determine a fragment hit density
and probability of kill of a modelled warhead. In order to simulate a
plenty of preformed fragments inside a warhead, the model requires
expensive computation resources. Therefore, this study attempts to
model the problem in an alternative approach by considering an
equivalent mass of preformed fragments to the mass of warhead
casing. This approach yields approximately 7% and 20% difference
of fragment velocities from the analytical results for one and two
layers of preformed fragments, respectively. The lethal ranges of the
simulated warheads are 42.6 m and 56.5 m for warheads with one and
two layers of preformed fragments, respectively, compared to 13.85
m for a warhead without preformed fragment. These lethal ranges are
based on the requirement of fragment hit density. The lethal ranges
which are based on the probability of kill are 27.5 m, 61 m and 70 m
for warheads with no preformed fragment, one and two layers of
preformed fragments, respectively.
Abstract: This paper presents a new feature based dense stereo
matching algorithm to obtain the dense disparity map via dynamic
programming. After extraction of some proper features, we use some
matching constraints such as epipolar line, disparity limit, ordering
and limit of directional derivative of disparity as well. Also, a coarseto-
fine multiresolution strategy is used to decrease the search space
and therefore increase the accuracy and processing speed. The
proposed method links the detected feature points into the chains and
compares some of the feature points from different chains, to
increase the matching speed. We also employ color stereo matching
to increase the accuracy of the algorithm. Then after feature
matching, we use the dynamic programming to obtain the dense
disparity map. It differs from the classical DP methods in the stereo
vision, since it employs sparse disparity map obtained from the
feature based matching stage. The DP is also performed further on a
scan line, between any matched two feature points on that scan line.
Thus our algorithm is truly an optimization method. Our algorithm
offers a good trade off in terms of accuracy and computational
efficiency. Regarding the results of our experiments, the proposed
algorithm increases the accuracy from 20 to 70%, and reduces the
running time of the algorithm almost 70%.
Abstract: White rust, caused by Albugo candida, is the most
destructive foliar diseases of persian cress, Lepidium sativum in Iran.
Application of fungicide is the most common method for the disease
control. However, regarding the problems created by synthetic
pesticides application, environmentally safe methods are needed to
replace chemical pesticides. In this study, the antifungal activity of
plant natural extracts was investigated for their ability to inhibit
zoospore release from sporangia of A. candida. The crude extract of
46 plants was obtained using methanol. The inhibitory effect of the
extracts was examined by mixing the plant extracts with a
zoosporangial suspension of A. candida (1×106 spore/ml) at three
concentrations, 250, 100 and 50 ppm. The experiments were
conducted in a completely randomized design, with three replicates.
The results of the experiment showed that three out of 46 plants
species, including, Rhus coriaria, Anagallis arvensis and Mespilus
germanica were completely inhibit zoospore release from
zoosporangia of Albugo candida at concentration of 50 ppm.
Abstract: Y chromosome microdeletions are the most common
genetic cause of male infertility and screening for these
microdeletions in azoospermic or severely oligospermic men is now
standard practice. Analysis of the Y chromosome in men with
azoospermia or severe oligozoospermia has resulted in the
identification of three regions in the euchromatic part of the long arm
of the human Y chromosome (Yq11) that are frequently deleted in
men with otherwise unexplained spermatogenic failure. PCR analysis
of microdeletions in the AZFa, AZFb and AZFc regions of the
human Y chromosome is an important screening tool. The aim of this
study was to analyse the type of microdeletions in men with fertility
disorders in Slovakia. We evaluated 227 patients with azoospermia
and with normal karyotype. All patient samples were analyzed
cytogenetically. For PCR amplification of sequence-tagged sites
(STS) of the AZFa, AZFb and AZFc regions of the Y chromosome
was used Devyser AZF set. Fluorescently labeled primers for all
markers in one multiplex PCR reaction were used and for automated
visualization and identification of the STS markers we used genetic
analyzer ABi 3500xl (Life Technologies). We reported 13 cases of
deletions in the AZF region 5,73%. Particular types of deletions were
recorded in each region AZFa,b,c .The presence of microdeletions in
the AZFc region was the most frequent. The study confirmed that
percentage of microdeletions in the AZF region is low in Slovak
azoospermic patients, but important from a prognostic view.
Abstract: Eutrophication of surface water is one of the most
widespread environmental problems at present. Large number of
pilgrims and tourists visit sacred artificial tank known as “Brahma
Sarover” located at Kurukshetra, India to take holy dip and perform
religious ceremonies. The sources of pollutants include impurities in
feed water, mass bathing, religious offerings and windblown
particulate matter. Studies so far have focused mainly on assessing
water quality for bathing purpose by using physico-chemical and
bacteriological parameters. No effort has been made to assess nutrient
concentration and trophic status of the tank to take more appropriate
measures for improving water quality on long term basis. In the
present study, total nitrogen, total phosphorous and chlorophyll a
measurements have been done to assess the nutrient level and trophic
status of the tank. The results show presence of high concentration of
nutrients and Chlorophyll a indicating mesotrophic and eutrophic
state of the tank. Phosphorous has been observed as limiting nutrient
in the tank water.
Abstract: Biodiesel production with used frying by
transesterification reaction with methanol, using a commercial
kaolinite thermally-activated solid acid catalyst was investigated.
The surface area, the average pore diameter and pore volume of the
kaolinite catalyst were 10 m2/g, 13.0 nm and 30 mm3/g, respectively.
The optimal conditions for the transesterification reaction were
determined to be oil/methanol, in a molar ratio 1:31, temperature 160
ºC and catalyst concentration of 3% (w/w). The yield of fatty acids
methyl esters (FAME) was 92.4% after 2 h of reaction. This method
of preparation of biodiesel can be a positive alternative for utilizing
used frying corn oil for feedstock of biodiesel combined with the
inexpensive catalyst.
Abstract: Mining tailings represent a generating source of rich heavy metal material with a potential danger the public health and the environment, since these metals, under certain conditions, can leach and contaminate aqueous systems that serve like supplying potable water sources. The strategy for this work is based on the observation, experimentation and the simulation that can be obtained by binding real answers of the hydrodynamic behavior of metals leached from mining tailings, and the applied mathematics that provides the logical structure to decipher the individual effects of the general physicochemical phenomenon. The case of study presented herein focuses on mining tailings deposits located in Monte San Nicolas, Guanajuato, Mexico, an abandoned mine. This was considered the contamination source that under certain physicochemical conditions can favor the metal leaching, and its transport towards aqueous systems. In addition, the cartography, meteorology, geology and the hydrodynamics and hydrological characteristics of the place, will be helpful in determining the way and the time in which these systems can interact. Preliminary results demonstrated that arsenic presents a great mobility, since this one was identified in several superficial aqueous systems of the micro watershed, as well as in sediments in concentrations that exceed the established maximum limits in the official norms. Also variations in pH and potential oxide-reduction were registered, conditions that favor the presence of different species from this element its solubility and therefore its mobility.
Abstract: Drilling of glass sheets with different thicknesses have
been carried out by Abrasive Jet Machining process (AJM) in order
to determine its machinability under different controlling parameters
of the AJM process. The present study has been introduced a
mathematical model and the obtained results have been compared
with that obtained from other models published earlier [1-6]. The
experimental results of the present work are used to discuss the
validity of the proposed model as well as the other models.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: The mixed oxide nuclear fuel (MOX) of U and Pu contains several percent of fission products and minor actinides, such as neptunium, americium and curium. It is important to determine accurately the decay heat from Curium isotopes as they contribute significantly in the MOX fuel. This heat generation can cause samples to melt very quickly if excessive quantities of curium are present. In the present paper, we introduce a new approach that can predict the decay heat from curium isotopes. This work is a part of the project funded by King Abdulaziz City of Science and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, and take place in King Abdulaziz University (KAU), Saudi Arabia. The approach is based on the numerical solution of coupled linear differential equations that describe decays and buildups of many nuclides to calculate the decay heat produced after shutdown. Results show the consistency and reliability of the approach applied.
Abstract: For over a decade, the Pulse Coupled Neural Network
(PCNN) based algorithms have been successfully used in image
interpretation applications including image segmentation. There are
several versions of the PCNN based image segmentation methods,
and the segmentation accuracy of all of them is very sensitive to the
values of the network parameters. Most methods treat PCNN
parameters like linking coefficient and primary firing threshold as
global parameters, and determine them by trial-and-error. The
automatic determination of appropriate values for linking coefficient,
and primary firing threshold is a challenging problem and deserves
further research. This paper presents a method for obtaining global as
well as local values for the linking coefficient and the primary firing
threshold for neurons directly from the image statistics. Extensive
simulation results show that the proposed approach achieves
excellent segmentation accuracy comparable to the best accuracy
obtainable by trial-and-error for a variety of images.
Abstract: This study realizes an empirical investigation of main factors to develop an accounting career, stereotypes on accountants and accounting and perceptions on future career path for a sample of master students in accounting. The research provides some insight into what master students consider when choosing their future career paths. The most important two reasons chosen by students were “career opportunities" and “future earnings. They see accounting as structured, governed by conformity, requiring skills in working with numbers, monotonous, accurate, more efficient than effective but also absorbing, interesting and involving a certain degree of novelty. Although these students plan to start their careers in a multinational or accounting/audit firm, most of those plan to leave after five years. It resulted that women value more flexibility and time requiring special attention in retention policies practiced by firms.
Abstract: The problem of robust disturbance rejection (RDR) using a proportional state feedback controller is studied for the case of Left Invertible MIMO generalized state space linear systems with nonlinear uncertain structure. Sufficient conditions for the problem to have a solution are established. The set of all proportional feedback controllers solving the problem subject to these conditions is analytically determined.
Abstract: Three strains of Vibrio parahaemolyticus (690, BCRC
13023 and BCRC 13025) implicated in food poisoning outbreaks in
Taiwan were subjected to acid adaptation at pH 5.5 for 90 min. The
growth behaviors of acid-adapted and non-adapted V.
parahaemolyticus in the media supplemented with various nitrogen
and carbon sources were investigated. The effects of acid adaptation
on the thermostable direct hemolysin (TDH) secretion and fatty acid
profiles of V. parahaemolyticus were also examined. Results showed
that acid-adapted and non-adapted V. parahaemolyticus 690, BCRC
13023 and BCRC 13025 grew similarly in TSB-3% NaCl and basal
media supplemented with various carbon and nitrogen sources during
incubation period. Higher TDH secretion was noted with V.
parahaemolyticus 690 among the three strains. However, acid-adapted
strains produced less amounts of TDH than non-adapted strains when
they were grown in TSB-3% NaCl. Additionally, acid adaptation
increased the ratio of SFA/USFA in cells of V. parahaemolyticus
strains.
Abstract: One of the main research directions in CAD/CAM
machining area is the reducing of machining time.
The feedrate scheduling is one of the advanced techniques that
allows keeping constant the uncut chip area and as sequel to keep
constant the main cutting force. They are two main ways for feedrate
optimization. The first consists in the cutting force monitoring, which
presumes to use complex equipment for the force measurement and
after this, to set the feedrate regarding the cutting force variation. The
second way is to optimize the feedrate by keeping constant the
material removal rate regarding the cutting conditions.
In this paper there is proposed a new approach using an extended
database that replaces the system model.
The feedrate scheduling is determined based on the identification
of the reconfigurable machine tool, and the feed value determination
regarding the uncut chip section area, the contact length between tool
and blank and also regarding the geometrical roughness.
The first stage consists in the blank and tool monitoring for the
determination of actual profiles. The next stage is the determination
of programmed tool path that allows obtaining the piece target
profile.
The graphic representation environment models the tool and blank
regions and, after this, the tool model is positioned regarding the
blank model according to the programmed tool path. For each of
these positions the geometrical roughness value, the uncut chip area
and the contact length between tool and blank are calculated. Each of
these parameters are compared with the admissible values and
according to the result the feed value is established.
We can consider that this approach has the following advantages:
in case of complex cutting processes the prediction of cutting force is
possible; there is considered the real cutting profile which has
deviations from the theoretical profile; the blank-tool contact length
limitation is possible; it is possible to correct the programmed tool
path so that the target profile can be obtained.
Applying this method, there are obtained data sets which allow the
feedrate scheduling so that the uncut chip area is constant and, as a
result, the cutting force is constant, which allows to use more
efficiently the machine tool and to obtain the reduction of machining
time.