Abstract: In this paper a controller for the pitch angle of an
aircraft regarding to the elevator deflection angle is designed.
The way how the elevator angle affects pitching motion of the
aircraft is pointed out, as well as, how a pitch controller can be
applied for the aircraft to reach certain pitch angle. In this digital
optimal system, the elevator deflection angle and pitching angle
of the plane are considered to be input and output respectively.
A single input single output (SISO) system is presented. A
digital pitch aircraft control is demonstrated. A simulation for
the whole system has been performed. The optimal control
weighting vectors, Q and R have been determined.
Abstract: The objective of the research was focused on the
design, development and evaluation of a sustainable web based
network system to be used as an interoperable environment for
University process workflow and document management. In this
manner the most of the process workflows in Universities can be
entirely realized electronically and promote integrated University.
Definition of the most used University process workflows enabled
creating electronic workflows and their execution on standard
workflow execution engines. Definition or reengineering of
workflows provided increased work efficiency and helped in having
standardized process through different faculties. The concept and the
process definition as well as the solution applied as Case study are
evaluated and findings are reported.
Abstract: The breakdown strength characteristic of Low Density
Polyethylene films (LDPE) under DC voltage application and the
effect of water absorption have been studied. Mainly, our experiment
was investigated under two conditions; dry and heavy water
absorption. Under DC ramp voltage, the result found that the
breakdown strength under heavy water absorption has a lower value
than dry condition. In order to clarify the effect, the temperature rise of
film was observed using non contact thermograph until the occurrence
of the electrical breakdown and the conduction current of the sample
was also measured in correlation with the thermograph measurement.
From the observations, it was shown that under the heavy water
absorption, the hot spot in the samples appeared at lower voltage. At
the same voltage the temperature of the hot spot and conduction
current was higher than that under the dry condition. The measurement
result has a good correlation between the existence of a critical field
for conduction current and thermograph observation. In case of the
heavy water absorption, the occurrence of the threshold field was
earlier than the dry condition as result lead to higher of conduction
current and the temperature rise appears after threshold field was
significantly increased in increasing of field. The higher temperature
rise was caused by the higher current conduction as the result the
insulation leads to breakdown to the lower field application.
Abstract: In this paper, the Gaussian type quadrature rules for fuzzy functions are discussed. The errors representation and convergence theorems are given. Moreover, four kinds of Gaussian type quadrature rules with error terms for approximate of fuzzy integrals are presented. The present paper complements the theoretical results of the paper by T. Allahviranloo and M. Otadi [T. Allahviranloo, M. Otadi, Gaussian quadratures for approximate of fuzzy integrals, Applied Mathematics and Computation 170 (2005) 874-885]. The obtained results are illustrated by solving some numerical examples.
Abstract: The purpose of the experiments described in this article was the comparison of integrated fixed film activated sludge (IFAS) and activated sludge (AS) system. The IFAS applied system consists of the cigarette filter rods (wasted filter in tobacco factories) as a biofilm carrier. The comparison with activated sludge was performed by two parallel treatment lines. Organic substance, ammonia and TP removal was investigated over four month period. Synthetic wastewater was prepared with ordinary tap water and glucose as the main sources of carbon and energy, plus balanced macro and micro nutrients. COD removal percentages of 94.55%, and 81.62% were achieved for IFAS and activated sludge system, respectively. Also, ammonia concentration significantly decreased by increasing the HRT in both systems. The average ammonia removal of 97.40 % and 96.34% were achieved for IFAS and activated sludge system, respectively. The removal efficiency of total phosphorus (TP-P) was 60.64%, higher than AS process by 56.63% respectively.
Abstract: Biological data has several characteristics that strongly differentiate it from typical business data. It is much more complex, usually large in size, and continuously changes. Until recently business data has been the main target for discovering trends, patterns or future expectations. However, with the recent rise in biotechnology, the powerful technology that was used for analyzing business data is now being applied to biological data. With the advanced technology at hand, the main trend in biological research is rapidly changing from structural DNA analysis to understanding cellular functions of the DNA sequences. DNA chips are now being used to perform experiments and DNA analysis processes are being used by researchers. Clustering is one of the important processes used for grouping together similar entities. There are many clustering algorithms such as hierarchical clustering, self-organizing maps, K-means clustering and so on. In this paper, we propose a clustering algorithm that imitates the ecosystem taking into account the features of biological data. We implemented the system using an Ant-Colony clustering algorithm. The system decides the number of clusters automatically. The system processes the input biological data, runs the Ant-Colony algorithm, draws the Topic Map, assigns clusters to the genes and displays the output. We tested the algorithm with a test data of 100 to1000 genes and 24 samples and show promising results for applying this algorithm to clustering DNA chip data.
Abstract: A simple method for the simultaneous determination
of hippuric acid and benzoic acid in urine using reversed-phase high
performance liquid chromatography was described. Chromatography
was performed on a Nova-Pak C18 (3.9 x 150 mm) column with a
mobile phase of mixed solution methanol: water: acetic acid
(20:80:0.2) and UV detection at 254 nm. The calibration curve was
linear within concentration range at 0.125 to 6.0 mg/ml of hippuric
acid and benzoic acid. The recovery, accuracy and coefficient
variance of hippuric acid were 104.54%, 0.2% and 0.2% respectively
and for benzoic acid were 98.48%, 1.25% and 0.60% respectively.
The detection limit of this method was 0.01ng/l for hippuric acid and
0.06ng/l for benzoic acid. This method has been applied to the
analysis of urine samples from the suspected of toluene abuser or
glue sniffer among secondary school students at Johor Bahru.
Abstract: Biodiesel is traditionally produced from oleaginous
plants. On the other hand, increasing biodiesel production from these
raw materials could create problems of food supply. Producing
biodiesel from microalgae could help to overcome this difficulty,
because microalgae are rich in lipids and do not compete for arable
lands. However, no studies had compared vegetable and microalgae
oil-based biodiesel in terms of yield, viscosity and heat of
combustion. In the present study, commercial canola and microalgae
oil were therefore transesterified with methanol under a homogenous
alkali catalyst (potassium hydroxide) at 100oC for 1h. The result
showed that microalgae-based oil has a higher yield in biodiesel with
89.7% (g biodiesel/g oil) and a lower kinematic viscosity (22oC) of
4.31 mm/s2 than canola oil.
Abstract: A generalized unified power quality conditioner
(GUPQC) by using three single-phase three-level voltage source
converters (VSCs) connected back-to-back through a common dc
link is proposed in this paper as a new custom power device for a
three-feeder distribution system. One of the converters is connected
in shunt with one feeder for mitigation of current harmonics and
reactive power compensation, while the other two VSCs are
connected in series with the other two feeders to maintain the load
voltage sinusoidal and at constant level. A new control scheme based
on synchronous reference frame is proposed for series converters.
The simulation analysis on compensation performance of GUPQC
based on PSCAD/EMTDC is reported.
Abstract: This paper presents a new algorithm for the channel estimation of the OFDM system based on a pilot signal for the new generation of high data rate communication systems. In orthogonal frequency division multiplexing (OFDM) systems over fast-varying fading channels, channel estimation and tracking is generally carried out by transmitting known pilot symbols in given positions of the frequency-time grid. In this paper, we propose to derive an improved algorithm based on the calculation of the mean and the variance of the adjacent pilot signals for a specific distribution of the pilot signals in the OFDM frequency-time grid then calculating of the entire unknown channel coefficients from the equation of the mean and the variance. Simulation results shows that the performance of the OFDM system increase as the length of the channel increase where the accuracy of the estimated channel will be increased using this low complexity algorithm, also the number of the pilot signal needed to be inserted in the OFDM signal will be reduced which lead to increase in the throughput of the signal over the OFDM system in compared with other type of the distribution such as Comb type and Block type channel estimation.
Abstract: Malting is usually carried out on intact barley seed,
while hull is still attached to it. In this study, oat grain with and
without hull was subjected to controlled germination to optimize its
enzymes activity, in such a way that lipase has the lowest and α-
amylase and proteinase the highest activities. Since pH has a great
impact on the activity of the enzymes, the pH of germination media
was set up to 3 to 8. In dehulled oats, lipase and α-amylase had the
lowest and highest activities in pHs 3 and 6, respectively whereas the
highest proteinase activity was evidenced at pH 7 and 4 in the oats
with and without hull respectively. While measurements indicated
that the effect of hull on the enzyme activities particularly in lipase
and amylase at each level of the pH are significantly different, the
best results were obtained in those samples in which their hull had
been removed. However, since the similar lipase activity in
germinated dehulled oat were recorded at the pHs 4 and 5, therefore
it was concluded that pH 5 in dehulled oat seed may provide the
optimum enzyme activity for all the enzymes.
Abstract: The techniques for estimating the adhesive and cohesive strength in high velocity oxy fuel (HVOF) thermal spray coatings have been discussed and compared. The development trend and the last investigation have been studied. We will focus on benefits and limitations of these methods in different process and materials.
Abstract: Poly (ethylene glycol) (PEG) molecules attached to surfaces have shown high potential as a protein repellent due to their flexibility and highly water solubility. A quartz crystal microbalance recording frequency and dissipation changes (QCM-D) has been used to study the adsorption from aqueous solutions, of lysozyme and α-lactalbumin proteins (the last with and without calcium) onto modified stainless steel surfaces. Surfaces were coated with poly(ethylene imine) (PEI) and silicate before grafting on PEG molecules. Protein adsorption was also performed on the bare stainless steel surface as a control. All adsorptions were conducted at 23°C and pH 7.2. The results showed that the presence of PEG molecules significantly reduced the adsorption of lysozyme and α- lactalbumin (with calcium) onto the stainless steel surface. By contrast, and unexpected, PEG molecules enhanced the adsorption of α-lactalbumin (without calcium). It is suggested that the PEG -α- lactalbumin hydrophobic interaction plays a dominant role which leads to protein aggregation at the surface for this latter observation. The findings also lead to the general conclusion that PEG molecules are not a universal protein repellent. PEG-on-PEI surfaces were better at inhibiting the adsorption of lysozyme and α-lactalbumin (with calcium) than with PEG-on-silicate surfaces.
Abstract: In this study, aeroelastic response and performance
analyses have been conducted for a 5MW-Class composite wind
turbine blade model. Advanced coupled numerical method based on
computational fluid dynamics (CFD) and computational flexible
multi-body dynamics (CFMBD) has been developed in order to
investigate aeroelastic responses and performance characteristics of
the rotating composite blade. Reynolds-Averaged Navier-Stokes
(RANS) equations with k-ω SST turbulence model were solved for
unsteady flow problems on the rotating turbine blade model. Also,
structural analyses considering rotating effect have been conducted
using the general nonlinear finite element method. A fully implicit
time marching scheme based on the Newmark direct integration
method is applied to solve the coupled aeroelastic governing equations
of the 3D turbine blade for fluid-structure interaction (FSI) problems.
Detailed dynamic responses and instantaneous velocity contour on the
blade surfaces which considering flow-separation effects were
presented to show the multi-physical phenomenon of the huge rotating
wind- turbine blade model.
Abstract: Maize and Indian mustard are significant crops in
semi-arid climate zones of India. Improved water management
requires precise scheduling of irrigation, which in turn requires an
accurate computation of daily crop evapotranspiration (ETc). Daily
crop evapotranspiration comes as a product of reference
evapotranspiration (ET0) and the growth stage specific crop
coefficients modified for daily variation. The first objective of
present study is to develop crop coefficients Kc for Maize and Indian
mustard. The estimated values of Kc for maize at the four crop
growth stages (initial, development, mid-season, and late season) are
0.55, 1.08, 1.25, and 0.75, respectively, and for Indian mustard the Kc
values at the four growth stages are 0.3, 0.6, 1.12, and 0.35,
respectively. The second objective of the study is to compute daily
crop evapotranspiration from ET0 and crop coefficients. Average
daily ETc of maize varied from about 2.5 mm/d in the early growing
period to > 6.5 mm/d at mid season. The peak ETc of maize is 8.3
mm/d and it occurred 64 days after sowing at the reproductive growth
stage when leaf area index was 4.54. In the case of Indian mustard,
average ETc is 1 mm/d at the initial stage, >1.8 mm/d at mid season
and achieves a peak value of 2.12 mm/d on 56 days after sowing.
Improved schedules of irrigation have been simulated based on daily
crop evapo-transpiration and field measured data. Simulation shows a
close match between modeled and field moisture status prevalent
during crop season.
Abstract: This paper proposes the method combining artificial
neural network (ANN) with particle swarm optimization (PSO) to
implement the maximum power point tracking (MPPT) by controlling
the rotor speed of the wind generator. First, the measurements of wind
speed, rotor speed of wind power generator and output power of wind
power generator are applied to train artificial neural network and to
estimate the wind speed. Second, the method mentioned above is
applied to estimate and control the optimal rotor speed of the wind
turbine so as to output the maximum power. Finally, the result reveals
that the control system discussed in this paper extracts the maximum
output power of wind generator within the short duration even in the
conditions of wind speed and load impedance variation.
Abstract: The experiment was then conducted to investigate the
effect of cassava peel addition in the concentrate on the performance
of lactating dairy cows. Twenty four Holstein Friesian crossbred
(>87.5% Holstein Friesian) lactating dairy cows in mid lactation;
averaging 12.2+2.1 kg of milk, 119+45 days in milk, 44.1+6.2
months old and 449+33 kg live weight, were stratified for milk yield,
days in milk, age, stage of lactation and body weight, and then
randomly allocated to three treatment groups. The first, second and
third groups were fed concentrates containing the respective cassava
peel, 0, 20 and 40%. All cows were fed ad libitum corn silage and
freely access to clean water. Dry matter intake, 4%FCM, milk
composition and body weight change were affected (P
Abstract: Information Technology (IT) projects are always
accompanied by various risks and because of high rate of failure in
such projects, managing risks in order to neutralize or at least
decrease their effects on the success of the project is strongly
essential. In this paper, fuzzy analytical hierarchy process (FAHP) is
exploited as a means of risk evaluation methodology to prioritize and
organize risk factors faced in IT projects. A real case of IT projects, a
project of design and implementation of an integrated information
system in a vehicle producing company in Iran is studied. Related
risk factors are identified and then expert qualitative judgments about
these factors are acquired. Translating these judgments to fuzzy
numbers and using them as an input to FAHP, risk factors are then
ranked and prioritized by FAHP in order to make project managers
aware of more important risks and enable them to adopt suitable
measures to deal with these highly devastative risks.
Abstract: This paper focuses on robust design and optimization
of industrial production wastes. Past literatures were reviewed to case
study Clamason Industries Limited (CIL) - a leading ladder-tops
manufacturer. A painstaking study of the firm-s practices at the shop
floor revealed that Over-production, Waiting time, Excess inventory,
and Defects are the major wastes that are impeding their progress and
profitability. Design expert8 software was used to apply Taguchi
robust design and response surface methodology in order to model,
analyse and optimise the wastes cost in CIL. Waiting time and overproduction
rank first and second in contributing to the costs of wastes
in CIL. For minimal wastes cost the control factors of overproduction,
waiting-time, defects and excess-inventory must be set at
0.30, 390.70, 4 and 55.70 respectively for CIL. The optimal value of
cost of wastes for the months studied was 22.3679. Finally, a
recommendation was made that for the company to enhance their
profitability and customer satisfaction, they must adopt the Shingeo
Shingo-s Single Minute Exchange of Dies (SMED), which will
immediately tackle the waste of waiting by drastically reducing their
setup time.
Abstract: This paper proposes a set of quasi-static mathematical
model of magnetic fields caused by high voltage conductors of
distribution transformer by using a set of second-order partial
differential equation. The modification for complex magnetic field
analysis and time-harmonic simulation are also utilized. In this
research, transformers were study in both balanced and unbalanced
loading conditions. Computer-based simulation utilizing the threedimensional
finite element method (3-D FEM) is exploited as a tool
for visualizing magnetic fields distribution volume a distribution
transformer. Finite Element Method (FEM) is one among popular
numerical methods that is able to handle problem complexity in
various forms. At present, the FEM has been widely applied in most
engineering fields. Even for problems of magnetic field distribution,
the FEM is able to estimate solutions of Maxwell-s equations
governing the power transmission systems. The computer simulation
based on the use of the FEM has been developed in MATLAB
programming environment.