Abstract: The surface water used in this study was collected from the Chao Praya River at the lower part at the Nonthaburi bridge. It was collected and used throughout the experiment. TOC (also known as DOC) in the range between 2.5 to 5.6 mg/l were investigated in this experiment. The use of conventional treatment methods such as FeCl3 and PAC showed that TOC removal was 65% using FeCl3 and 78% using PAC (powder activated carbon). The advanced oxidation process alone showed only 35% removal of TOC. Coupling advanced oxidation with a small amount of PAC (0.05g/L) increased efficiency by upto 55%. The combined BAC with advanced oxidation process and small amount of PAC demonstrated the highest efficiency of up to 95% of TOC removal and lower sludge production compared with other methods.
Abstract: The paper deals with the effect of ion nitriding and
carbonitriding on fatigue strength of steel parts under the fretting
conditions. Instrumented fatigue tests were carried out on surface
treated flat bars from EA1N and EA4T steels with different strength.
The chosen surfacing decrease importantly an unfavorable fretting
effect. Nitridation suppressed the unfavorable effect of fretting
almost entirely, while the influence of carbonitridation was less
striking. The results were compared with those ones obtained on bars
without surfacing. The causes of favorable influence of surfacing are
discussed.
Abstract: The Euler-s equation of motion is extended to include
the viscosity stress tensor leading to the formulation of Navier–
Stokes type equation. The latter is linearized and applied to
investigate the rotational motion or vorticity in a viscous fluid.
Relations for the velocity of viscous waves and attenuation parameter
are obtained in terms of viscosity (μ) and the density (¤ü) of the fluid.
μ and ¤ü are measured experimentally as a function of temperature for
two different samples of light and heavy crude oil. These data
facilitated to determine the activation energy, velocity of viscous
wave and the attenuation parameter. Shear wave velocity in heavy oil
is found to be much larger than the light oil, whereas the attenuation
parameter in heavy oil is quite low in comparison to light one. The
activation energy of heavy oil is three times larger than light oil.
Abstract: The implementation of Super-Ultra Low Emission
Vehicle standards requires more efficient exhaust gas purification. To
increase the efficiency of exhaust gas purification, an the adsorbent
capable of holding hydrocarbons up to 250-300 ОС should be
developed. The possibility to design such adsorbents by modification
of zeolites of mordenite type, ZSM-5 and NaY, using different
metals cations has been studied.
It has been shown that introducing Cr, Cs, Zn, Ni, Co, Li, Mn in
zeolites results in modification of the toluene TPD and toluene
sorption capacity.
5%LiZSM-5 zeolite exhibits the most attractive TPD curve, with
toluene desorption temperature ranging from 250 to 350ОС. The
sorption capacity of 5%Li-ZSM-5 is 0.4 mmol/g. NaY zeolite has the
highest sorption capacity, up to 2 mmol/g, and holds toluene up to
350ОС, but at 120ОС toluene desorption starts, which is not desirable,
since the adsorbent of cold start hydrocarbons should retain them
until 250-300ОС. Therefore 5%LiZSM-5 zeolite was found to be the
most promising to control the cold-start hydrocarbon emissions
among the samples studied.
Abstract: In this paper, optimal generation expansion planning (GEP) is investigated considering purchase prices, profits of independent power producers (IPPs) and reliability criteria using a new method based on hybrid coded Genetic Algorithm (GA) and Particle Swarm Optimization (PSO). In this approach, optimal purchase price of each IPP is obtained by HCGA and reliability criteria are calculated by PSO technique. It should be noted that reliability criteria and the rate of carbon dioxide (CO2) emission have been considered as constraints of the GEP problem. Finally, the proposed method has been tested on the case study system. The results evaluation show that the proposed method can simply obtain optimal purchase prices of IPPs and is a fast method for calculation of reliability criteria in expansion planning. Also, considering the optimal purchase prices and profits of IPPs in generation expansion planning are caused that the expansion costs are decreased and the problem is solved more exactly.
Abstract: The abundance and availability of rice husk, an agricultural waste, make them as a good source for precursor of activated carbon. In this work, rice husk-based activated carbons were prepared via base treated chemical activation process prior the carbonization process. The effect of carbonization temperatures (400, 600 and 800oC) on their pore structure was evaluated through morphology analysis using scanning electron microscope (SEM). Sample carbonized at 800oC showed better evolution and development of pores as compared to those carbonized at 400 and 600oC. The potential of rice husk-based activated carbon as an alternative adsorbent was investigated for the removal of Ni(II), Zn(II) and Pb(II) from single metal aqueous solution. The adsorption studies using rice husk-based activated carbon as an adsorbent were carried out as a function of contact time at room temperature and the metal ions were analyzed using atomic absorption spectrophotometer (AAS). The ability to remove metal ion from single metal aqueous solution was found to be improved with the increasing of carbonization temperature. Among the three metal ions tested, Pb(II) ion gave the highest adsorption on rice husk-based activated carbon. The results obtained indicate the potential to utilize rice husk as a promising precursor for the preparation of activated carbon for removal of heavy metals.
Abstract: Due to the call of global warming effects, city planners aim at actions for reducing carbon emission. One of the approaches is to promote the usage of public transportation system toward the transit-oriented-development. For example, rapid transit system in Taipei city and Kaohsiung city are opening. However, until November 2008 the average daily patronage counted only 113,774 passengers at Kaohsiung MRT systems, much less than which was expected. Now the crucial questions: how the public transport competes with private transport? And more importantly, what factors would enhance the use of public transport? To give the answers to those questions, our study first applied regression to analyze the factors attracting people to use public transport around cities in the world. It is shown in our study that the number of MRT stations, city population, cost of living, transit fare, density, gasoline price, and scooter being a major mode of transport are the major factors. Subsequently, our study identified successful and unsuccessful cities in regard of the public transport usage based on the diagnosis of regression residuals. Finally, by comparing transportation strategies adopted by those successful cities, our conclusion stated that Kaohsiung City could apply strategies such as increasing parking fees, reducing parking spaces in downtown area, and reducing transfer time by providing more bus services and public bikes to promote the usage of public transport.
Abstract: Bacterial magnetic nanoparticles have great useful potential in biotechnological and biomedical applications. In this study, a liquid growth medium was modified for cultivation a fastidious magnetotactic bacterium that has been isolated from Anzali
lagoon, Iran in our previous research. These modifications include
change in vitamin, mineral, carbon sources and etcetera. In our
experience, the serum bottles and designed air-tight laboratory bottles
were used to create microaerobic conditions in order to development
of a method for scale-up experiment. This information may serve as a
guide to green chemistry based biological protocols for the synthesis
of magnetic nanoparticles with control over the chemical
composition, morphology and size.
Abstract: In order to compare the performance of the carbon dioxide and HFC-125 heat pumps for medium-and high-temperature heating, both heat pump cycles were optimized using a simulation method. To fairly compare the performance of the cycles by using different working fluids, each cycle was optimized from the viewpoint of heating COP by two design parameters. The first is the gas cooler exit temperature and the other is the ratio of the overall heat conductance of the gas cooler to the combined overall heat conductance of the gas cooler and the evaporator. The inlet and outlet temperatures of secondary fluid of the gas cooler were fixed at 40/90°C and 40/150°C.The results shows that the HFC-125 heat pump has 6% higher heating COP than carbon dioxide heat pump when the heat sink exit temperature is fixed at 90ºC, while the latter outperforms the former when the heat sink exit temperature is fixed at 150ºC under the simulation conditions considered in the present study.
Abstract: Microbial oil was produced by soil isolated
oleaginous yeast YU5/2 in flask-batch fermentation. The yeast was
identified by molecular genetics technique based on sequence
analysis of the variable D1/D2 domain of the large subunit (26S)
ribosomal DNA and it was identified as Torulaspora globosa. T.
globosa YU5/2 supported maximum values of 0.520 g/L/d, 0.472 g
lipid/g cells, 4.16 g/L, and 0.156 g/L/d for volumetric lipid
production rate, and specific yield of lipid, lipid concentration, and
specific rate of lipid production respectively, when culture was
performed in nitrogen-limiting medium supplemented with 80g/L
glucose. Among the carbon sources tested, maximum cell yield
coefficient (YX/S, g/L), maximum specific yield of lipid (YP/X, g
lipid/g cells) and volumetric lipid production rate (QP, g/L/d) were
found of 0.728, 0.237, and 0.619, respectively, using sweet potato
tubers hydrolysates as carbon source.
Abstract: Stress-strain curve of inter-tube connected carbon nanotube (CNT) reinforced polymer composite under axial loading generated from molecular dynamics simulation is presented. Comparison of the response to axial mechanical loading between this composite system with composite systems reinforced by long, continuous CNTs (replicated via periodic boundary conditions) and short, discontinuous CNTs has been made. Simulation results showed that the inter-tube connection improved the mechanical properties of short discontinuous CNTs dramatically. Though still weaker than long CNT/polymer composite, more remarkable increase in the stiffness relative to the polymer was observed in the inter-tube connected CNT/polymer composite than in the discontinuous CNT/polymer composite. The manually introduced bridge break process resulted in a stress-strain curve of ductile fracture mode, which is consistent with the experimental result.
Abstract: The paper presents the results of microhardness and
microstructure of low carbon steel surface melted using carbon
dioxide laser with a wavelength of 10.6μm and a maximum output
power of 2000W. The processing parameters such as the laser power,
and the scanning rate were investigated in this study. After surface
melting two distinct regions formed corresponding to the melted zone
MZ, and the heat affected zone HAZ. The laser melted region
displayed a cellular fine structures while the HAZ displayed
martensite or bainite structure. At different processing parameters,
the original microstructure of this steel (Ferrite+Pearlite) has been
transformed to new phases of martensitic and bainitic structures. The
fine structure and the high microhardness are evidence of the high
cooling rates which follow the laser melting. The melting pool and
the transformed microstructure in the laser surface melted region of
carbon steel showed clear dependence on laser power and scanning
rate.
Abstract: Most buildings have been using anchor bolts
commonly for installing outdoor advertising structures. Anchor bolts
of common carbon steel are widely used and often installed
indiscriminately by inadequate installation standards. In the area
where strong winds frequently blow, falling accidents of outdoor
advertising structures can occur and cause a serious disaster, which is
very dangerous and to be prevented. In this regard, the development of
high-performance anchor bolts is urgently required. In the present
study, 25Cr-8Ni-1.5Si-1Mn-0.4C alloy was produced by traditional
vacuum induction melting (VIM) for the application of anchor bolt.
The alloy composition is revealed as a duplex microstructure from
thermodynamic phase analysis by FactSage® and confirmed by
metallographic experiment. Addition of Nitrogen to the alloy was
found to reduce the ferritic phase domain and significantly increase the
hardness and the tensile strength. Microstructure observation revealed
mixed structure of austenite and ferrite with fine carbide distributed
along the grain and phase boundaries.
Abstract: The photochemical and photo-Fenton oxidation of 1,3-dichloro-2-propanol was performed in a batch reactor, at room temperature, using UV radiation, H2O2 as oxidant, and Fenton-s reagent. The effect of the oxidative agent-s initial concentration was investigated as well as the effect of the initial concentration of Fe(II) by following the target compound degradation, the total organic carbon removal and the chloride ion production. Also, from the kinetic analysis conducted and proposed reaction scheme it was deduced that the addition of Fe(II) significantly increases the production and the further oxidation of the chlorinated intermediates.
Abstract: A new dual-fluid concept was studied that could eventually find application for cold-gas propulsion for small space satellites or other constant flow applications. In basic form, the concept uses two different refrigerant working fluids, each having a different saturation vapor pressure. The higher vapor pressure refrigerant remains in the saturation phase and is used to pressurize the lower saturation vapor pressure fluid (the propellant) which remains in the compressed liquid phase. A demonstration thruster concept based on this principle was designed and built to study its operating characteristics. An automotive-type electronic fuel injector was used to meter and deliver the propellant. Ejected propellant mass and momentum were measured for several combinations of refrigerants and hydrocarbon fluids. The thruster has the advantage of delivering relatively large total impulse at low tank pressure within a small volume.
Abstract: Fruits and vegetables are the essentials of a healthy
diet, mainly because of their antioxidant properties contributing to
disease blockage especially for some certain types of cancer. Being a
favourite fruit, citrus are produced for economic and commercial
purposes worldwide. Particularly, lemon fruit (Citrus limon L.), has
an important place in export products of Turkey. Lemon has a great
importance on human nutrition with regard to being a source of
nutrients, flavonoids, vitamin C and minerals. It is used for food
flavouring and pickling and also processed for lemonade. By
processing citrus into fruit juices, consumption may increase and also
become easier. Like many fruits and vegetables lemons are cheap and
abundant during harvesting period, while they are quite expensive in
other seasons. Lemon juice and concentrate production allows
consumers to get benefits from lemon fruit in any time of the year.
Lemonade is getting in to the focus of consumers’ attention
preferring non-carbonated drinks. The demand of healthy, convenient
functional foods affects consumer trends through innovative
products. For this reason, lemonade could be enriched with different
natural herb extracts such as ginger (Zingiber officinale), linden (Tilia
cordata), and mint (Mentha piperita).
Abstract: Nuclear matrix protein 22 (NMP22) is a FDA approved
biomarker for bladder cancer. The objective of this study is to develop
a simple NMP22 immumosensor (NMP22-IMS) for accurate
measurement of NMP22. The NMP22-IMS was constructed with
NMP22 antibody immobilized on screen-printed carbon electrodes.
The construction procedures and antibody immobilization are simple.
Results showed that the NMP22-IMS has an excellent (r2³0.95)
response range (20 – 100 ng/mL). In conclusion, a simple and reliable
NMP22-IMS was developed, capable of precisely determining urine
NMP22 level.
Abstract: Chemical and physical functionalization of multiwalled
carbon nanotubes (MWCNT) has been commonly practiced to
achieve better dispersion of carbon nanotubes (CNTs) in polymer
matrix. This work describes various functionalization methods (acidtreatment,
non-ionic surfactant treatment with TritonX-100),
fabrication of MWCNT/PP nanocomposites via melt blending and
characterization of mechanical properties. Microscopy analysis
(FESEM, TEM, XPS) showed effective purification of MWCNTs
under acid treatment, and better dispersion under both chemical and
physical functionalization techniques combined, in their respective
order. Tensile tests showed increase in tensile strength for the
nanocomposites that contain MWCNTs up to 2 wt%. A decrease in
tensile strength was seen in samples that contain 4 wt% of MWCNTs
for both raw and Triton X-100 functionalized, signifying MWCNT
degradation/rebundling at composition with higher content of
MWCNTs. For the acid-treated MWCNTs, however, the tensile
results showed slight improvement even at 4wt%, indicating effective
dispersion of MWCNTs.
Abstract: The elimimation of mefenamic acid has been carried
out by photolysis, ozonation, adsorption onto activated carbon (AC)
and combinations of the previous single systems (O3+AC and
O3+UV). The results obtained indicate that mefenamic acid is not
photo-reactive, showing a relatively low quantum yield of the order
of 6 x 10-4 mol Einstein-1. Application of ozone to mefenamic
aqueous solutions instantaneously eliminates the pharmaceutical,
achieving simultaneously a 40% of mineralization. Addition of AC to
the ozonation process does not enhance the process, moreover,
mineralization is completely inhibited if compared to results obtained
by single ozonation. The combination of ozone and UV radiation led
to the best results in terms of mineralization (60% after 120 min).
Abstract: The effects of divers carbon substrates were
investigated for the tabtoxin production of an isolated pathogenic
Pseudomonas syringae pv. tabaci, the causal agent of wildfire of
tobacco and are discussed in relation to the bacterium growth. The
isolated organism was grown in batch culture on Woolley's
medium (28°C, 200 rpm, during 5 days). The growth has been
measured by the optical density (OD) at 620 nm and the tabtoxin
production quantified by Escherichia coli (K-12) bioassay
technique. The growth and the tabtoxin production were both
influenced by the substrates (sugars, amino acids, organic acids)
used, each, as a sole carbon source and as a supplement for the
same amino acids. The most significant quantities of tabtoxin were
obtained in presence of some amino acids used as sole carbon
source and/or as supplement.