Abstract: The progress of industry integrated circuits in recent
years has been pushed by continuous miniaturization of transistors.
With the reduction of dimensions of components at 0.1 micron and
below, new physical effects come into play as the standard simulators
of two dimensions (2D) do not consider. In fact the third dimension
comes into play because the transverse and longitudinal dimensions
of the components are of the same order of magnitude. To describe
the operation of such components with greater fidelity, we must
refine simulation tools and adapted to take into account these
phenomena. After an analytical study of the static characteristics of
the component, according to the different operating modes, a
numerical simulation is performed of field-effect transistor with
submicron gate MESFET GaInP. The influence of the dimensions of
the gate length is studied. The results are used to determine the
optimal geometric and physical parameters of the component for their
specific applications and uses.
Abstract: The increasing demand of gallium, indium and
rare-earth elements for the production of electronics, e.g. solid
state-lighting, photovoltaics, integrated circuits, and liquid crystal
displays, will exceed the world-wide supply according to current
forecasts. Recycling systems to reclaim these materials are not yet in
place, which challenges the sustainability of these technologies. This
paper proposes a multispectral imaging system as a basis for a vision
based recognition system for valuable components of electronics
waste. Multispectral images intend to enhance the contrast of images
of printed circuit boards (single components, as well as labels) for
further analysis, such as optical character recognition and entire
printed circuit board recognition. The results show, that a higher
contrast is achieved in the near infrared compared to ultraviolett and
visible light.
Abstract: The spring-driven ball-type check valve is one of the
most important components of hydraulic systems: it controls the
position of the ball and prevents backward flow. To simplify the
structure, the spring must be eliminated, and to accomplish this, the
flow pattern and the behavior of the check ball in L-shaped pipe must
be determined. In this paper, we present a full-scale model of a check
ball made of acrylic resin, and we determine the relationship between
the initial position of the ball, the position and diameter of the inflow
port. The check flow rate increases in a standard center inflow model,
and it is possible to greatly decrease the check-flow rate by shifting the
inflow from the center.
Abstract: The development, operation and maintenance of
Integrated Waste Management Systems (IWMS) affects essentially
the sustainable concern of every region. The features of such systems
have great influence on all of the components of sustainability. In
order to reach the optimal way of processes, a comprehensive
mapping of the variables affecting the future efficiency of the system
is needed such as analysis of the interconnections among the
components and modeling of their interactions. The planning of a
IWMS is based fundamentally on technical and economical
opportunities and the legal framework. Modeling the sustainability
and operation effectiveness of a certain IWMS is not in the scope of
the present research. The complexity of the systems and the large
number of the variables require the utilization of a complex approach
to model the outcomes and future risks. This complex method should
be able to evaluate the logical framework of the factors composing
the system and the interconnections between them. The authors of
this paper studied the usability of the Fuzzy Cognitive Map (FCM)
approach modeling the future operation of IWMS’s. The approach
requires two input data set. One is the connection matrix containing
all the factors affecting the system in focus with all the
interconnections. The other input data set is the time series, a
retrospective reconstruction of the weights and roles of the factors.
This paper introduces a novel method to develop time series by
content analysis.
Abstract: Leukaemia is a blood cancer disease that contributes
to the increment of mortality rate in Malaysia each year. There are
two main categories for leukaemia, which are acute and chronic
leukaemia. The production and development of acute leukaemia cells
occurs rapidly and uncontrollable. Therefore, if the identification of
acute leukaemia cells could be done fast and effectively, proper
treatment and medicine could be delivered. Due to the requirement of
prompt and accurate diagnosis of leukaemia, the current study has
proposed unsupervised pixel segmentation based on clustering
algorithm in order to obtain a fully segmented abnormal white blood
cell (blast) in acute leukaemia image. In order to obtain the
segmented blast, the current study proposed three clustering
algorithms which are k-means, fuzzy c-means and moving k-means
algorithms have been applied on the saturation component image.
Then, median filter and seeded region growing area extraction
algorithms have been applied, to smooth the region of segmented
blast and to remove the large unwanted regions from the image,
respectively. Comparisons among the three clustering algorithms are
made in order to measure the performance of each clustering
algorithm on segmenting the blast area. Based on the good sensitivity
value that has been obtained, the results indicate that moving kmeans
clustering algorithm has successfully produced the fully
segmented blast region in acute leukaemia image. Hence, indicating
that the resultant images could be helpful to haematologists for
further analysis of acute leukaemia.
Abstract: An environmentally benign protocol for the one-pot,
three-component synthesis of Triazolo[1,2-a]indazole-1,3,8-trione
derivatives by condensation of dimedone, urazole and aromatic
aldehydes catalyzed by HClO4/SiO2 NPS as an ecofriendly catalyst
with high catalytic activity and reusability at 100ºC under solventfree
conditions is reported. The reaction proceeds to completion
within 20-30 min in 77-86% yield.
Abstract: Food is widely packaged with plastic materials to
prevent microbial contamination and spoilage. Ionizing radiation is
widely used to sterilize the food-packaging materials. Sterilization by
γ-radiation causes degradation such as embrittlement, stiffening,
softening, discoloration, odour generation, and decrease in molecular
weight. Many antioxidants can prevent γ-degradation but most of
them are toxic. The migration of antioxidants to its environment
gives rise to major concerns in case of food packaging plastics. In
this attempt, we have aimed to utilize synergistic mixtures of
stabilizers which are approved for food-contact applications.
Ethylene-propylene-diene terpolymer has been melt-mixed with
hindered amine stabilizers (HAS), phenolic antioxidants and organophosphites
(hydroperoxide decomposer). Results were discussed by
comparing the stabilizing efficiency of mixtures with and without
phenol system. Among phenol containing systems where we mostly
observed discoloration due to the oxidation of hindered phenol, the
combination of secondary HAS, tertiary HAS, organo-phosphite and
hindered phenol exhibited improved stabilization efficiency than
single or binary additive systems. The mixture of secondary HAS and
tertiary HAS, has shown antagonistic effect of stabilization.
However, the combination of organo-phosphite with secondary HAS,
tertiary HAS and phenol antioxidants have been found to give
synergistic even at higher doses of Gamma-irradiation. The effects
have been explained through the interaction between the stabilizers.
After γ-irradiation, the consumption of oligomeric stabilizer
significantly depends on the components of stabilization mixture. The
effect of the organo-phosphite antioxidant on the overall stability has
been discussed.
Abstract: Composite materials, due to their unique properties
such as high strength to weight ratio, corrosion resistance, and impact
resistance have huge potential as structural materials in automotive,
construction and transportation applications. However, these
properties often come at higher cost owing to complex design
methods, difficult manufacturing processes and raw material cost.
Traditionally, tapered laminated composite structures are
manufactured using autoclave manufacturing process by ply drop off
technique. Autoclave manufacturing though very powerful suffers
from high capital investment and higher energy consumption. As per
the current trends in composite manufacturing, Out of Autoclave
(OoA) processes are looked as emerging technologies for
manufacturing the structural composite components for aerospace
and defense applications. However, there is a need for improvement
among these processes to make them reliable and consistent. In this
paper, feasibility of using out of autoclave process to manufacture the
variable thickness cantilever beam is discussed. The minimum weight
design for the composite beam is obtained using constant stress beam
concept by tailoring the thickness of the beam. Ply drop off
techniques was used to fabricate the variable thickness beam from
glass/epoxy prepregs. Experiments were conducted to measure
bending stresses along the span of the cantilever beam at different
intervals by applying the concentrated load at the free end.
Experimental results showed that the stresses in the bean at different
intervals were constant. This proves the ability of OoA process to
manufacture the constant stress beam. Finite element model for the
constant stress beam was developed using commercial finite element
simulation software. It was observed that the simulation results
agreed very well with the experimental results and thus validated
design and manufacturing approach used.
Abstract: It is widely believed that mobile device is a promising technology for lending the opportunity for the third wave of electronic commerce. Mobile devices have changed the way companies do business. Many applications are under development or being incorporated into business processes. In this day, mobile applications are a vital component of any industry strategy.One of the greatest benefits of selling merchandise and providing services on a mobile application is that it widens a company’s customer base significantly.Mobile applications are accessible to interested customers across regional and international borders in different electronic business (e-business) area. But there is a dark side to this success story. The security risks associated with mobile devices and applications are very significant. This paper introduces a broad risk analysis for the various threats, vulnerabilities, and risks in mobile e-business applications and presents some important risk mitigation approaches. It reviews and compares two different frameworks for security assurance in mobile e-business applications. Based on the comparison, the paper suggests some recommendations for applications developers and business owners in mobile e-business application development process.
Abstract: Batteries of electric vehicles (BEV) are becoming
more attractive with the advancement of new battery technologies
and promotion of electric vehicles. BEV batteries are recharged on
board vehicles using either the grid (G2V for Grid to Vehicle) or
renewable energies in a stand-alone application (H2V for Home to
Vehicle). This paper deals with the modeling, sizing and control of a
photovoltaic stand-alone application that can charge the BEV at
home. The modeling approach and developed mathematical models
describing the system components are detailed. Simulation and
experimental results are presented and commented.
Abstract: Lightweight design represents an important key to
successful implementation of energy-saving, fuel-efficient and
environmentally friendly means of transport in the aerospace and
automotive industry. In this context the use of carbon fibre reinforced
plastics (CFRP) which are distinguished by their outstanding
mechanical properties at relatively low weight, promise significant
improvements. Due to the reduction of the total mass, with the
resulting lowered fuel or energy consumption and CO2 emissions
during the operational phase, commercial aircraft will increasingly be
made of CFRP. An auspicious technology for the efficient and
economic production of high performance thermoset composites and
hybrid structures for future lightweight applications is the
combination of carbon fibre sheet moulding compound, tailored
continuous carbon fibre reinforcements and metallic components in a
one-shot pressing and curing process. This paper deals with a hybrid
composite technology for aerospace industries, which was developed
with the help of a special innovation and development system.
Abstract: A Distributed Denial of Service (DDoS) attack is a
major threat to cyber security. It originates from the network layer or
the application layer of compromised/attacker systems which are
connected to the network. The impact of this attack ranges from the
simple inconvenience to use a particular service to causing major
failures at the targeted server. When there is heavy traffic flow to a
target server, it is necessary to classify the legitimate access and
attacks. In this paper, a novel method is proposed to detect DDoS
attacks from the traces of traffic flow. An access matrix is created
from the traces. As the access matrix is multi dimensional, Principle
Component Analysis (PCA) is used to reduce the attributes used for
detection. Two classifiers Naive Bayes and K-Nearest neighborhood
are used to classify the traffic as normal or abnormal. The
performance of the classifier with PCA selected attributes and actual
attributes of access matrix is compared by the detection rate and
False Positive Rate (FPR).
Abstract: In this paper we describe the Levenvberg-Marquardt
(LM) algorithm for identification and equalization of CDMA
signals received by an antenna array in communication channels.
The synthesis explains the digital separation and equalization of
signals after propagation through multipath generating intersymbol
interference (ISI). Exploiting discrete data transmitted and three
diversities induced at the reception, the problem can be composed
by the Block Component Decomposition (BCD) of a tensor of
order 3 which is a new tensor decomposition generalizing the
PARAFAC decomposition. We optimize the BCD decomposition by
Levenvberg-Marquardt method gives encouraging results compared to
classical alternating least squares algorithm (ALS). In the equalization
part, we use the Minimum Mean Square Error (MMSE) to perform
the presented method. The simulation results using the LM algorithm
are important.
Abstract: Presently, engine cooling pump is driven by toothed
belt. Therefore, the pump speed is dependent on engine speed which
varies their output. At normal engine operating conditions (Higher
RPM and low load, Higher RPM and high load), mechanical water
pumps in existing engines are inevitably oversized and so the use of
an electric water pump together with state-of-the-art thermal
management of the combustion engine has measurable advantages.
Demand-driven cooling, particularly in the cold-start phase, saves
fuel (approx 3 percent) and leads to a corresponding reduction in
emissions. The lack of dependence on a mechanical drive also results
in considerable flexibility in component packaging within the engine
compartment. This paper describes the testing and comparison of
existing mechanical water pump with that of the electric water pump.
When the existing mechanical water pump is replaced with the new
electric water pump the percentage gain in system efficiency is also
discussed.
Abstract: The most important component affecting the
efficiency of photovoltaic power systems are solar panels. In other
words, efficiency of these systems are significantly affected due to
the being low efficiency of solar panel. Thus, solar panels should be
operated under maximum power point conditions through a power
converter. In this study, design of boost converter has been carried
out with maximum power point tracking (MPPT) algorithm which is
incremental conductance (Inc-Cond). By using this algorithm,
importance of power converter in MPPT hardware design, impacts of
MPPT operation have been shown. It is worth noting that initial
operation point is the main criteria for determining the MPPT
performance. In addition, it is shown that if value of load resistance is
lower than critical value, failure operation is realized. For these
analyzes, direct duty control is used for simplifying the control.
Abstract: Currently, thorium fuel has been especially noticed
because of its proliferation resistance than long half-life alpha emitter
minor actinides, breeding capability in fast and thermal neutron flux
and mono-isotopic naturally abundant. In recent years, efficiency of
minor actinide burning up in PWRs has been investigated. Hence, a
minor actinide-contained thorium based fuel matrix can confront both
proliferation resistance and nuclear waste depletion aims. In the
present work, minor actinide depletion rate in a CANDU-type nuclear
core modeled using MCNP code has been investigated. The obtained
effects of minor actinide load as mixture of thorium fuel matrix on
the core neutronics has been studied with comparing presence and
non-presence of minor actinide component in the fuel matrix.
Depletion rate of minor actinides in the MA-contained fuel has been
calculated using different power loads. According to the obtained
computational data, minor actinide loading in the modeled core
results in more negative reactivity coefficients. The MA-contained
fuel achieves less radial peaking factor in the modeled core. The
obtained computational results showed 140 kg of 464 kg initial load
of minor actinide has been depleted in during a 6-year burn up in 10
MW power.
Abstract: Liposome plays an important role in medical and
pharmaceutical science as e.g. nano scale drug carriers. Liposomes
are vesicles of varying size consisting of a spherical lipid bilayer and
an aqueous inner compartment. Magnet-driven liposome used for the
targeted delivery of drugs to organs and tissues. These liposome
preparations contain encapsulated drug components and finely
dispersed magnetic particles.
Liposomes are vesicles of varying size consisting of a spherical
lipid bilayer and an aqueous inner compartment that are generated in
vitro. These are useful in terms of biocompatibility, biodegradability,
and low toxicity, and can control biodistribution by changing the size,
lipid composition, and physical characteristics. Furthermore,
liposomes can entrap both hydrophobic and hydrophilic drugs and are
able to continuously release the entrapped substrate, thus being useful
drug carriers. Magnetic liposomes (MLs) are phospholipid vesicles
that encapsulate magneticor paramagnetic nanoparticles. They are
applied as contrast agents for magnetic resonance imaging (MRI).
The biological synthesis of nanoparticles using plant extracts plays
an important role in the field of nanotechnology. Green-synthesized
magnetite nanoparticles-protein hybrid has been produced by treating
Iron (III) / Iron (II) chloride with the leaf extract of Datura inoxia.
The phytochemicals present in the leaf extracts act as a reducing as
well stabilizing agents preventing agglomeration, which include
flavonoids, phenolic compounds, cardiac glycosides, proteins and
sugars.
The magnetite nanoparticles-protein hybrid has been trapped
inside the aqueous core of the liposome prepared by reversed phase
evaporation (REV) method using oleic and linoleic acid which has
been shown to be driven under magnetic field confirming the
formation magnetic liposome (ML). Chemical characterization of
stealth magnetic liposome has been performed by breaking the
liposome and release of magnetic nanoparticles. The presence iron
has been confirmed by colour complex formation with KSCN and
UV-Vis study using spectrophotometer Cary 60, Agilent.
This magnet driven liposome using nanoparticles-protein hybrid
can be a smart vesicles for the targeted drug delivery.
Abstract: A field experiment was carried out at Arab El-
Awammer Research Station, Agric. Res. Center. Assiut Governorate
during summer seasons of 2013 and 2014. The present study assessed
the effect of cowpea with maize intercropping on yield and its
components. The experiment comprised of three treatments (sole
cowpea, sole maize and cowpea-maize intercrop). The experimental
design was a randomized complete block with four replications.
Results indicated that intercropped maize plants with cowpea,
exhibited greater potentiality and resulted in higher values of most of
the studied criteria viz., plant height, number of ears/plant, number of
rows/ear, number of grains/row, grains weight/ear, 100–grain weight
and straw and grain yields. Fresh and dry forage yields of cowpea
were lower in intercropping with maize than sole. Furthermore, the
combined of the two seasons revealed that the total Land Equivalent
Ratio (LER) between cowpea and maize was 1.65. The Aggressivity
(A) maize was 0.45 and cowpea was -0.45. This showed that maize
was the dominant crop, whereas cowpea was the dominated. The
Competitive Ratio (CR) indicated that maize more competitive than
cowpea, maize was 1.75 and cowpea was 0.57. The Actual Yield
Loss (AYL) maize was 0.05 and cowpea was -0.40. The Monetary
Advantage Index (MAI) was 2360.80.
Abstract: Near infrared (NIR) spectroscopy has always been of
great interest in the food and agriculture industries. The development
of prediction models has facilitated the estimation process in recent
years. In this study, 110 crude palm oil (CPO) samples were used to
build a free fatty acid (FFA) prediction model. 60% of the collected
data were used for training purposes and the remaining 40% used for
testing. The visible peaks on the NIR spectrum were at 1725 nm and
1760 nm, indicating the existence of the first overtone of C-H bands.
Principal component regression (PCR) was applied to the data in
order to build this mathematical prediction model. The optimal
number of principal components was 10. The results showed
R2=0.7147 for the training set and R2=0.6404 for the testing set.
Abstract: Axial flow fans, while incapable of developing high
pressures, they are well suitable for handling large volumes of air at
relatively low pressures. In general, they are low in cost and possess
good efficiency, and can have blades of airfoil shape. Axial flow fans
show good efficiencies, and can operate at high static pressures if
such operation is necessary. Our objective is to model and analyze
the flow through AXIAL FANS using CFD Software and draw
inference from the obtained results, so as to get maximum efficiency.
The performance of an axial fan was simulated using CFD and the
effect of variation of different parameters such as the blade number,
noise level, velocity, temperature and pressure distribution on the
blade surface was studied. This paper aims to present a final 3D CAD
model of axial flow fan. Adapting this model to the available
components in the market, the first optimization was done. After this
step, CFX flow solver is used to do the necessary numerical analyses
on the aerodynamic performance of this model. This analysis results
in a final optimization of the proposed 3D model which is presented
in this article.