Abstract: This paper deals with the optimal design of two-channel recursive parallelogram quadrature mirror filter (PQMF) banks. The analysis and synthesis filters of the PQMF bank are composed of two-dimensional (2-D) recursive digital all-pass filters (DAFs) with nonsymmetric half-plane (NSHP) support region. The design problem can be facilitated by using the 2-D doubly complementary half-band (DC-HB) property possessed by the analysis and synthesis filters. For finding the coefficients of the 2-D recursive NSHP DAFs, we appropriately formulate the design problem to result in an optimization problem that can be solved by using a weighted least-squares (WLS) algorithm in the minimax (L∞) optimal sense. The designed 2-D recursive PQMF bank achieves perfect magnitude response and possesses satisfactory phase response without requiring extra phase equalizer. Simulation results are also provided for illustration and comparison.
Abstract: This paper proposes method of diagnosing ball screw
preload loss through the Hilbert-Huang Transform （HHT） and
Multiscale entropy （MSE） process. The proposed method can
diagnose ball screw preload loss through vibration signals when the
machine tool is in operation. Maximum dynamic preload of 2 %, 4 %,
and 6 % ball screws were predesigned, manufactured, and tested
experimentally. Signal patterns are discussed and revealed using
Empirical Mode Decomposition（EMD）with the Hilbert Spectrum.
Different preload features are extracted and discriminated using HHT.
The irregularity development of a ball screw with preload loss is
determined and abstracted using MSE based on complexity
perception. Experiment results show that the proposed method can
predict the status of ball screw preload loss. Smart sensing for the
health of the ball screw is also possible based on a comparative
evaluation of MSE by the signal processing and pattern matching of
EMD/HHT. This diagnosis method realizes the purposes of prognostic
effectiveness on knowing the preload loss and utilizing convenience.
Abstract: Starting from the basic pillars of the supportability
analysis this paper queries its characteristics in LCI (Life Cycle
Integration) environment. The research methodology contents a
review of modern logistics engineering literature with the objective to
collect and synthesize the knowledge relating to standards of
supportability design in e-logistics environment. The results show
that LCI framework has properties which are in fully compatibility
with the requirement of simultaneous logistics support and productservice
bundle design. The proposed approach is a contribution to the
more comprehensive and efficient supportability design process.
Also, contributions are reflected through a greater consistency of
collected data, automated creation of reports suitable for different
analysis, as well as the possibility of their customization according
with customer needs. In addition to this, convenience of this approach
is its practical use in real time. In a broader sense, LCI allows
integration of enterprises on a worldwide basis facilitating electronic
business.
Abstract: This paper presents an assessment study conducted
among the distance learners in India. Open and distance learning
systems have traveled a long way since its inception and its journey
has witnessed the evolution and adoption of different generations of
technology. This study focuses on the distant learners in India.
Sampling for this study has been derived from the mass enrollment
from Tamil Nadu area, a southern state of India. Learners were
chosen from dual mode universities, private universities, Tamil Nadu
Open University and IGNOU. The main focus of the study is to
examine the coverage and appropriation of students support services
and learning aids. It explores two aspects: the facilities available and
the awareness and use of such services. It includes, self-learning
materials, face-to-face counseling, multimedia learning materials,
website, e-learning, radio and television services etc. While exploring
the student-s perspective on these learning aspects, it is important to
understand the perspectives of the teachers. Two different interests
are visible among the teachers. Majority of the teachers support faceto-
face counseling. However, the young teachers are in favour of
online learning and multimedia supports in teaching. Through the
awareness is somewhat high, the actual participation in online is very
low. This is due to the inadequate infrastructure as well as the
traditional attitudes of the teachers. Still the face-to-face sessions
remain popular than online.
Abstract: With the prevalence of computer and development of information technology, Geographic Information Systems (GIS) have long used for a variety of applications in electrical engineering. GIS are designed to support the analysis, management, manipulation and mapping of spatial data. This paper presents several usages of GIS in power utilities such as automated route selection for the construction of new power lines which uses a dynamic programming model for route optimization, load forecasting and optimizing planning of substation-s location and capacity with comprehensive algorithm which involves an accurate small-area electric load forecasting procedure and simulates the different cost functions of substations.
Abstract: In this paper, the application of the Mode Matching
(MM) method in the case of photonic crystal waveguide
discontinuities is presented. The structure under consideration is
divided into a number of cells, which supports a number of guided
and evanescent modes. These modes can be calculated numerically
by an alternative formulation of the plane wave expansion method
for each frequency. A matrix equation is then formed relating the
modal amplitudes at the beginning and at the end of the structure.
The theory is highly efficient and accurate and can be applied to
study the transmission sensitivity of photonic crystal devices due to
fabrication tolerances. The accuracy of the MM method is compared
to the Finite Difference Frequency Domain (FDFD) and the Adjoint
Variable Method (AVM) and good agreement is observed.
Abstract: The previous researches focused on the influence of
anthropogenic greenhouse gases exerting global warming, but not
consider whether desert sand may warm the planet, this could be
improved by accounting for sand's physical and geometric properties.
Here we show, sand particles (because of their geometry) at the desert
surface form an extended surface of up to 1 + π/4 times the planar area
of the desert that can contact sunlight, and at shallow depths of the
desert form another extended surface of at least 1 + π times the planar
area that can contact air. Based on this feature, an enhanced heat
exchange system between sunlight, desert sand, and air in the spaces
between sand particles could be built up automatically, which can
increase capture of solar energy, leading to rapid heating of the sand
particles, and then the heating of sand particles will dramatically heat
the air between sand particles. The thermodynamics of deserts may
thus have contributed to global warming, especially significant to
future global warming if the current desertification continues to
expand.
Abstract: This paper presents the automated methods employed
for extracting craniofacial landmarks in white light images as part of
a registration framework designed to support three neurosurgical
procedures. The intraoperative space is characterised by white light
stereo imaging while the preoperative plan is performed on CT scans.
The registration aims at aligning these two modalities to provide a
calibrated environment to enable image-guided solutions. The
neurosurgical procedures can then be carried out by mapping the
entry and target points from CT space onto the patient-s space. The
registration basis adopted consists of natural landmarks (eye corner
and ear tragus). A 5mm accuracy is deemed sufficient for these three
procedures and the validity of the selected registration basis in
achieving this accuracy has been assessed by simulation studies. The
registration protocol is briefly described, followed by a presentation
of the automated techniques developed for the extraction of the
craniofacial features and results obtained from tests on the AR and
FERET databases. Since the three targeted neurosurgical procedures
are routinely used for head injury management, the effect of
bruised/swollen faces on the automated algorithms is assessed. A
user-interactive method is proposed to deal with such unpredictable
circumstances.
Abstract: In this paper, the absorption and fluorescence
emission spectra of Yb:Y3Al5O12 (YAG)(25 at%) crystal as a disk
laser medium are measured at high temperature (300-450K). The
absorption and emission cross sections of Yb:YAG crystal are
determined using Reciprocity method. Temperature dependence of
941nm absorption cross section and 1031nm emission cross section
is extracted in the range of 300-450K. According to our experimental
results, an exponential temperature dependence between 300K and
450K is acquired for the 1031nm peak emission cross section and
also for 941nm peak absorption cross section of Yb:YAG crystal.
These results could be used for simulation and design of high power
highly doped Yb:YAG thin disk lasers.
Abstract: The relationship between different types of Molybdenum disulfide greases under extreme pressure loading and different speed situations have been studied using Design of Experiment (DOE) under 1200rpm steady state rotational speed and cyclic frequencies between 2400 and 1200rpm using a Plint machine software to set up the different rotational speed situations.
Research described here is aimed at providing good friction and wear performance while optimizing cyclic frequencies and MoS2 concentration due to the recent concern about grease behavior in extreme pressure applications. Extreme load of 785 Newton was used in conjunction with different cyclic frequencies (2400rpm -3.75min, 1200rpm -7.5min, 2400rpm -3.75min, 1200rpm -7.5min), to examine lithium based grease with and without MoS2 for equal number of revolutions, and a total run of 36000 revolutions; then compared to 1200rpm steady speed for the same total number of revolutions. 4 Ball wear tester was utilized to run large number of experiments randomly selected by the DOE software. The grease was combined with fine grade MoS2 or technical grade then heated to 750C and the wear scar width was collected at the end of each test. DOE model validation results verify that the data were very significant and can be applied to a wide range of extreme pressure applications. Based on simulation results and Scanning Electron images (SEM), it has been found that wear was largely dependent on the cyclic frequency condition. It is believed that technical grade MoS2 greases under faster cyclic speeds perform better and provides antiwear film that can resist extreme pressure loadings. Figures showed reduced wear scars width and improved frictional values.
Abstract: Recognizing human action from videos is an active
field of research in computer vision and pattern recognition. Human
activity recognition has many potential applications such as video
surveillance, human machine interaction, sport videos retrieval and
robot navigation. Actually, local descriptors and bag of visuals words
models achieve state-of-the-art performance for human action
recognition. The main challenge in features description is how to
represent efficiently the local motion information. Most of the
previous works focus on the extension of 2D local descriptors on 3D
ones to describe local information around every interest point. In this
paper, we propose a new spatio-temporal descriptor based on a spacetime
description of moving points. Our description is focused on an
Accordion representation of video which is well-suited to recognize
human action from 2D local descriptors without the need to 3D
extensions. We use the bag of words approach to represent videos.
We quantify 2D local descriptor describing both temporal and spatial
features with a good compromise between computational complexity
and action recognition rates. We have reached impressive results on
publicly available action data set
Abstract: Recent research has shown that milk proteins can
yield bioactive peptides with opioid, mineral binding,
cytomodulatory, antihypertensive, immunostimulating, antimicrobial
and antioxidative activity in the human body. Bioactive peptides are
encrypted in milk proteins and are only released by enzymatic
hydrolysis in vivo during gastrointestinal digestion, food processing
or by microbial enzymes in fermented products. At present
significant research is being undertaken on the health effects of
bioactive peptides. A variety of naturally formed bioactive peptides
have been found in fermented dairy products, such as yoghurt, sour
milk and cheese. In particular, antihypertensive peptides have been
identified in fermented milks, whey and ripened cheese. Some of
these peptides have been commercialized in the form of fermented
milks. Bioactive peptides have the potential to be used in the
formulation of health-enhancing nutraceuticals, and as potent drugs
with well defined pharmacological effects.
Abstract: Geosynthetics have proved to be suitable for
reinforced soil retaining walls. Based on the increasing uses of
geosynthetic reinforced soil systems in the regions, which bear
frequent earthquakes, the study of dynamic behavior of structures
seems necessary. Determining the reinforcement forces is; therefore,
one of the most important and main points of discussions in
designing retaining walls, by which we prevent from conservative
planning. Thus, this paper intended to investigate the effects of such
parameters as wall height, acceleration type, vertical spacing of
reinforcement, type of reinforcement and soil type on forces and
deformation through numerical modeling of the geosynthetic
reinforced soil retaining walls (GRSRW) under dynamic loading with
finite difference method by using FLAC. The findings indicate rather
positive results with each parameter.
Abstract: This paper proposes a neural network weights and
topology optimization using genetic evolution and the
backpropagation training algorithm. The proposed crossover and
mutation operators aims to adapt the networks architectures and
weights during the evolution process. Through a specific inheritance
procedure, the weights are transmitted from the parents to their
offsprings, which allows re-exploitation of the already trained
networks and hence the acceleration of the global convergence of the
algorithm. In the preprocessing phase, a new feature extraction
method is proposed based on Legendre moments with the Maximum
entropy principle MEP as a selection criterion. This allows a global
search space reduction in the design of the networks. The proposed
method has been applied and tested on the well known MNIST
database of handwritten digits.
Abstract: This work provides a practical method for the
development of rural road networks in rural areas of developing
countries. The proposed methodology enables to determine
obligatory points in the rural road network maximizing the number of
settlements that have access to basic services within a given
maximum distance. The proposed methodology is simple and
practical, hence, highly applicable to real-world scenarios, as
demonstrated in the definition of the road network for the rural areas
of Nepal.
Abstract: Mobile ad hoc network is a collection of mobile
nodes communicating through wireless channels without any
existing network infrastructure or centralized administration.
Because of the limited transmission range of wireless network
interfaces, multiple "hops" may be needed to exchange data
across the network. Consequently, many routing algorithms
have come into existence to satisfy the needs of
communications in such networks. Researchers have
conducted many simulations comparing the performance of
these routing protocols under various conditions and
constraints. One question that arises is whether speed of nodes
affects the relative performance of routing protocols being
studied. This paper addresses the question by simulating two
routing protocols AODV and DSDV. Protocols were
simulated using the ns-2 and were compared in terms of
packet delivery fraction, normalized routing load and average
delay, while varying number of nodes, and speed.
Abstract: Based on the combined shape feature and texture
feature, a fast object detection method with rotation invariant features
is proposed in this paper. A quick template matching scheme based
online learning designed for online applications is also introduced in
this paper. The experimental results have shown that the proposed
approach has the features of lower computation complexity and
higher detection rate, while keeping almost the same performance
compared to the HOG-based method, and can be more suitable for
run time applications.
Abstract: This paper describes topic of computer simulation with regard to the ground movement above an underground mine. Simulation made with software package ADINA for nonlinear elastic-plastic analysis with finite elements method. The one of representative profiles from Mine 'Stara Jama' in Zenica has been investigated. A collection and selection of both geo-mechanical data and geometric parameters of the mine was necessary for performing these simulations. Results of estimation have been compared with measured values (vertical displacement of surface), and then simulation performed with assumed dynamic and dimensions of excavation, over a period of time. Results are presented with bitmaps and charts.
Abstract: Design of a constant chord propeller is presented in
this paper in order to reduce propeller-s design procedure-s costs. The
design process was based on Lock and Goldstein-s techniques of
propeller design and analysis. In order to calculate optimum chord of
propeller, chord of a referential element is generalized as whole
blades chord. The design outcome which named CS-X-1 is modeled
& analyzed by CFD methods using K-ε: R.N.G turbulence model.
Convergence of results of two codes proved that outcome results of
design process are reliable. Design result is a two-blade propeller
with a total diameter of 1.1 meter, radial velocity of 3000 R.P.M,
efficiency above .75 and power coefficient near 1.05.
Abstract: The work describes the use of a synthetic transmit
aperture (STA) with a single element transmitting and all elements
receiving in medical ultrasound imaging. STA technique is a novel
approach to today-s commercial systems, where an image is acquired
sequentially one image line at a time that puts a strict limit on the
frame rate and the amount of data needed for high image quality. The
STA imaging allows to acquire data simultaneously from all
directions over a number of emissions, and the full image can be
reconstructed.
In experiments a 32-element linear transducer array with 0.48 mm
inter-element spacing was used. Single element transmission aperture
was used to generate a spherical wave covering the full image region.
The 2D ultrasound images of wire phantom are presented obtained
using the STA and commercial ultrasound scanner Antares to
demonstrate the benefits of the SA imaging.