Abstract: The wider growing Finite Element Method (FEM)
application is caused by its benefits of cost saving and environment
friendly. Also, by using FEM a deep understanding of certain
phenomenon can be achieved. This paper observed the role of
material properties and volumetric change when Solid State Phase
Transformation (SSPT) takes place in residual stress formation due to
a welding process of ferritic steels through coupled Thermo-
Metallurgy-Mechanical (TMM) analysis. The correctness of FEM residual stress prediction was validated by
experiment. From parametric study of the FEM model, it can be
concluded that the material properties change tend to over-predicts
residual stress in the weld center whilst volumetric change tend to
underestimates it. The best final result is the compromise of both by
incorporates them in the model which has a better result compared to
a model without SSPT.
Abstract: NiFe2O4 (nickel ferrite), ZnFe2O4 (zinc ferrite) and
Ni0.5Zn0.5Fe2O4 (nickel-zinc ferrite) were prepared by
mechanochemical route in a planetary ball mill starting from mixture
of the appropriate quantities of the Ni(OH)2/Fe(OH)3,
Zn(OH)2/Fe(OH)3 and Ni(OH)2/Zn(OH)2/Fe(OH)3 hydroxide
powders. In order to monitor the progress of chemical reaction and
confirm phase formation, powder samples obtained after 25 h, 18 h
and 10 h of milling were characterized by X-ray diffraction (XRD),
transmission electron microscopy (TEM), IR, Raman and Mössbauer
spectroscopy. It is shown that the soft mechanochemical method, i.e.
mechanochemical activation of hydroxides, produces high quality
single phase ferrite samples in much more efficient way. From the IR
spectroscopy of single phase samples it is obvious that energy of
modes depends on the ratio of cations. It is obvious that all samples
have more than 5 Raman active modes predicted by group theory in
the normal spinel structure. Deconvolution of measured spectra
allows one to conclude that all complex bands in the spectra are made
of individual peaks with the intensities that vary from spectrum to
spectrum. The deconvolution of Raman spectra allows to separate
contributions of different cations to a particular type of vibration and
to estimate the degree of inversion.
Abstract: Recent investigations have demonstrated the global
sea level rise due to climate change impacts. In this study, climate
changes study the effects of increasing water level in the strait of
Hormuz. The probable changes of sea level rise should be
investigated to employ the adaption strategies. The climatic output
data of a GCM (General Circulation Model) named CGCM3 under
climate change scenario of A1b and A2 were used. Among different
variables simulated by this model, those of maximum correlation
with sea level changes in the study region and least redundancy
among themselves were selected for sea level rise prediction by using
stepwise regression. One of models (Discrete Wavelet artificial
Neural Network) was developed to explore the relationship between
climatic variables and sea level changes. In these models, wavelet
was used to disaggregate the time series of input and output data into
different components and then ANN was used to relate the
disaggregated components of predictors and input parameters to each
other. The results showed in the Shahid Rajae Station for scenario
A1B sea level rise is among 64 to 75 cm and for the A2 Scenario sea
level rise is among 90 t0 105 cm. Furthermore, the result showed a
significant increase of sea level at the study region under climate
change impacts, which should be incorporated in coastal areas
management.
Abstract: In this glasshouse study, we developed a new imagebased
non-destructive technique for detecting leaf P status of
different crops such as cotton, tomato and lettuce. The plants were
grown on a nutrient solution containing different P concentrations,
e.g. 0%, 50% and 100% of recommended P concentration (P0 = no P,
L; P1 = 2.5 mL 10 L-1 of P and P2 = 5 mL 10 L-1 of P). After 7 weeks
of treatment, the plants were harvested and data on leaf P contents
were collected using the standard destructive laboratory method and
at the same time leaf images were collected by a handheld crop image
sensor. We calculated leaf area, leaf perimeter and RGB (red, green
and blue) values of these images. These data were further used in
linear discriminant analysis (LDA) to estimate leaf P contents, which
successfully classified these plants on the basis of leaf P contents.
The data indicated that P deficiency in crop plants can be predicted
using leaf image and morphological data. Our proposed nondestructive
imaging method is precise in estimating P requirements of
different crop species.
Abstract: The aim of the study is to improve the understanding
of latent and sensible thermal energy storage within a paraffin wax
media by an array of cylindrical tubes arranged both in in-line and
staggered layouts. An analytical and experimental study is carried out
in a horizontal shell-and-tube type system during melting process.
Pertamina paraffin-wax was used as a phase change material (PCM),
while the tubes are embedded in the PCM. From analytical study we
can obtain the useful information in designing a thermal energy
storage such as: the motion of interface, amount of material melted at
any time in the process, and the heat storage characteristic during
melting. The use of staggered tubes is proposed compared to in-line
layout in a heat exchanger as thermal storage. The experimental study
is used to verify the validity of the analytical predictions. From the
comparisons, the analytical and experimental data are in a good
agreement.
Abstract: Adoption of Information Systems (IS) is receiving
increasing attention such that its implications have been closely
monitored and studied by the IS management community, industry
and professional gatekeepers. Building on previous research
regarding the adoption of technology, this paper develops and
validates an integrated model of the adoption of mobile banking. The
model originates from the Technology Acceptance Model (TAM) and
the Theory of Planned Behaviour (TPB). This paper intends to offer a
preliminary scrutiny of the antecedents of the adoption of mobile
banking services in the context of a developing country. Data was
collected from Pakistan. The findings showed that an integrated TAM
and TPB model greatly explains the adoption intention of mobile
banking; and perceived behavioural control and its antecedents play a
significant role in predicting adoption Theoretical and managerial
implications of findings are presented and discussed.
Abstract: Prediction of maximum local scour is necessary for
the safety and economical design of the bridges. A number of
equations have been developed over the years to predict local scour
depth using laboratory data and a few pier equations have also been
proposed using field data. Most of these equations are empirical in
nature as indicated by the past publications. In this paper attempts
have been made to compute local depth of scour around bridge pier in
dimensional and non-dimensional form by using linear regression,
simple regression and SVM (Poly & Rbf) techniques along with few
conventional empirical equations. The outcome of this study suggests
that the SVM (Poly & Rbf) based modeling can be employed as an
alternate to linear regression, simple regression and the conventional
empirical equations in predicting scour depth of bridge piers. The
results of present study on the basis of non-dimensional form of
bridge pier scour indicate the improvement in the performance of
SVM (Poly & Rbf) in comparison to dimensional form of scour.
Abstract: This paper expands on the role of the professor by detailing the origins of the profession, adding some of the unique contributions of North American universities as well as some of the best practice recommendations to the unique tripartite role of the professor. It describes current challenges to the profession including the ever-controversial student rating of professors. It continues with the significance of empowerment to the role of the professor. It concludes with a predictive prescription for the future of the professoriate and the role of the university-level educational administrator toward that end.
Abstract: The critical concern of satellite operations is to ensure
the health and safety of satellites. The worst case in this perspective
is probably the loss of a mission, but the more common interruption
of satellite functionality can result in compromised mission
objectives. All the data acquiring from the spacecraft are known as
Telemetry (TM), which contains the wealth information related to the
health of all its subsystems. Each single item of information is
contained in a telemetry parameter, which represents a time-variant
property (i.e. a status or a measurement) to be checked. As a
consequence, there is a continuous improvement of TM monitoring
systems to reduce the time required to respond to changes in a
satellite's state of health. A fast conception of the current state of the
satellite is thus very important to respond to occurring failures.
Statistical multivariate latent techniques are one of the vital learning
tools that are used to tackle the problem above coherently.
Information extraction from such rich data sources using advanced
statistical methodologies is a challenging task due to the massive
volume of data. To solve this problem, in this paper, we present a
proposed unsupervised learning algorithm based on Principle
Component Analysis (PCA) technique. The algorithm is particularly
applied on an actual remote sensing spacecraft. Data from the
Attitude Determination and Control System (ADCS) was acquired
under two operation conditions: normal and faulty states. The models
were built and tested under these conditions, and the results show that
the algorithm could successfully differentiate between these
operations conditions. Furthermore, the algorithm provides
competent information in prediction as well as adding more insight
and physical interpretation to the ADCS operation.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive three phase inverter (TPI) for a photovoltaic
(PV) system at commercial level. The proposed model uses phase
locked loop (PLL) to synchronize the TPI with the power electric
grid (PEG) and performs MPC control in a dq reference frame. TPI
model consists of a boost converter (BC), maximum power point
tracking (MPPT) control, and a three-leg voltage source inverter
(VSI). The operational model of VSI is used to synthesize the
sinusoidal current and track the reference. The model is validated
using a 35.7 kW PV system in Matlab/Simulink. Implementation
results show simplicity and accuracy, as well as reliability of the
model.
Abstract: In this numerical study, effects of using Al2O3-water
nanofluid on the rate of heat transfer have been investigated. Physical
model is a square enclosure with insulated top and bottom horizontal
walls, while the vertical walls are kept at different constant
temperatures. Two appropriate models are used to evaluate the
viscosity and thermal conductivity of nanofluid. The governing
stream-vorticity equations are solved using a second order central
finite difference scheme, coupled to the conservation of mass and
energy. The study has been carried out for the nanoparticle diameter
30, 60 and 90 nm and the solid volume fraction 0 to 0.04. Results are
presented by average Nusselt number and normalized Nusselt number
in different range of φ and D for mixed convection dominated
regime. It is found that different heat transfer rate is predicted when
the effect of nanoparticle diameter is taken into account.
Abstract: This paper presents an extensive review of literature
relevant to the modelling techniques adopted in sediment yield and
hydrological modelling. Several studies relating to sediment yield are
discussed. Many research areas of sedimentation in rivers, runoff and
reservoirs are presented. Different types of hydrological models,
different methods employed in selecting appropriate models for
different case studies are analysed. Applications of evolutionary
algorithms and artificial intelligence techniques are discussed and
compared especially in water resources management and modelling.
This review concentrates on Genetic Programming (GP) and fully
discusses its theories and applications. The successful applications of
GP as a soft computing technique were reviewed in sediment
modelling. Some fundamental issues such as benchmark,
generalization ability, bloat, over-fitting and other open issues
relating to the working principles of GP are highlighted. This paper
concludes with the identification of some research gaps in
hydrological modelling and sediment yield.
Abstract: This paper integrates Octagon and Square Search
pattern (OCTSS) motion estimation algorithm into H.264/AVC
(Advanced Video Coding) video codec in Adaptive Group of Pictures
(AGOP) mode. AGOP structure is computed based on scene change
in the video sequence. Octagon and square search pattern block-based
motion estimation method is implemented in inter-prediction process
of H.264/AVC. Both these methods reduce bit rate and computational
complexity while maintaining the quality of the video sequence
respectively. Experiments are conducted for different types of video
sequence. The results substantially proved that the bit rate,
computation time and PSNR gain achieved by the proposed method
is better than the existing H.264/AVC with fixed GOP and AGOP.
With a marginal gain in quality of 0.28dB and average gain in bitrate
of 132.87kbps, the proposed method reduces the average computation
time by 27.31 minutes when compared to the existing state-of-art
H.264/AVC video codec.
Abstract: The need to save time and cost of soil testing at the
planning stage of road work has necessitated developing predictive
models. This study proposes a model for predicting the dry density of
lateritic soils stabilized with corn cob ash (CCA) and blended cement
- CCA. Lateritic soil was first stabilized with CCA at 1.5, 3.0, 4.5 and
6% of the weight of soil and then stabilized with the same
proportions as replacement for cement. Dry density, specific gravity,
maximum degree of saturation and moisture content were determined
for each stabilized soil specimen, following standard procedure.
Polynomial equations containing alpha and beta parameters for CCA
and blended CCA-cement were developed. Experimental values were
correlated with the values predicted from the Matlab curve fitting
tool, and the Solver function of Microsoft Excel 2010. The correlation
coefficient (R2) of 0.86 was obtained indicating that the model could
be accepted in predicting the maximum dry density of CCA stabilized
soils to facilitate quick decision making in roadworks.
Abstract: In the present study, analysis of heat transfer is carried
out in the slip flow region for the fluid flowing between two parallel
plates by employing the asymmetric heat fluxes at surface of the
plates. The flow is assumed to be hydrodynamically and thermally
fully developed for the analysis. The second order velocity slip and
viscous dissipation effects are considered for the analysis. Closed
form expressions are obtained for the Nusselt number as a function of
Knudsen number and modified Brinkman number. The limiting
condition of the present prediction for Kn = 0, Kn2 = 0, and Brq1 = 0
is considered and found to agree well with other analytical results.
Abstract: This article presents the main results of a numerical
investigation on the uncertainty of dynamic response of structures
with statistically correlated random damping Gamma distributed. A
computational method based on a Linear Statistical Model (LSM) is
implemented to predict second order statistics for the response of a
typical industrial building structure. The significance of random
damping with correlated parameters and its implications on the
sensitivity of structural peak response in the neighborhood of a
resonant frequency are discussed in light of considerable ranges of
damping uncertainties and correlation coefficients. The results are
compared to those generated using Monte Carlo simulation
techniques. The numerical results obtained show the importance of
damping uncertainty and statistical correlation of damping
coefficients when obtaining accurate probabilistic estimates of
dynamic response of structures. Furthermore, the effectiveness of the
LSM model to efficiently predict uncertainty propagation for
structural dynamic problems with correlated damping parameters is
demonstrated.
Abstract: Myocardial infarction is one of the leading causes of
death in the world. Some of these deaths occur even before the
patient reaches the hospital. Myocardial infarction occurs as a result
of impaired blood supply. Because the most of these deaths are due to
coronary artery disease, hence the awareness of the warning signs of
a heart attack is essential. Some heart attacks are sudden and intense,
but most of them start slowly, with mild pain or discomfort, then
early detection and successful treatment of these symptoms is vital to
save them. Therefore, importance and usefulness of a system
designing to assist physicians in early diagnosis of the acute heart
attacks is obvious. The main purpose of this study would be to enable patients to
become better informed about their condition and to encourage them
to seek professional care at an earlier stage in the appropriate
situations. For this purpose, the data were collected on 711 heart
patients in Iran hospitals. 28 attributes of clinical factors can be
reported by patients; were studied. Three logistic regression models
were made on the basis of the 28 features to predict the risk of heart
attacks. The best logistic regression model in terms of performance
had a C-index of 0.955 and with an accuracy of 94.9%. The variables,
severe chest pain, back pain, cold sweats, shortness of breath, nausea
and vomiting, were selected as the main features.
Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: An industrial system for the production of white
liquor of a paper industry, Klabin Paraná Papéis, formed by ten
reactors was modeled, simulated, and analyzed. The developed model
considered possible water losses by evaporation and reaction, in
addition to variations in volumetric flow of lime mud across the
reactors due to composition variations. The model predictions agreed
well with the process measurements at the plant and the results
showed that the slaking reaction is nearly complete at the third
causticizing reactor, while causticizing ends by the seventh reactor.
Water loss due to slaking reaction and evaporation occurs more
pronouncedly in the slaking reaction than in the final causticizing
reactors; nevertheless, the lime mud flow remains nearly constant
across the reactors.