Abstract: Palladium-catalyzed hydrodechlorination is a
promising alternative for the treatment of environmentally relevant
water bodies, such as groundwater, contaminated with chlorinated
organic compounds (COCs). In the aqueous phase
hydrodechlorination of COCs, Pd-based catalysts were found to have
a very high catalytic activity. However, the full utilization of the
catalyst-s potential is impeded by the sensitivity of the catalyst to
poisoning and deactivation induced by reduced sulfur compounds
(e.g. sulfides). Several regenerants have been tested before to recover
the performance of sulfide-fouled Pd catalyst. But these only
delivered partial success with respect to re-establishment of the
catalyst activity. In this study, the deactivation behaviour of
Pd/Al2O3 in the presence of sulfide was investigated. Subsequent to
total deactivation the catalyst was regenerated in the aqueous phase
using potassium permanganate. Under neutral pH condition,
oxidative regeneration with permanganate delivered a slow recovery
of catalyst activity. However, changing the pH of the bulk solution to
acidic resulted in the complete recovery of catalyst activity within a
regeneration time of about half an hour. These findings suggest the
superiority of permanganate as regenerant in re-activating Pd/Al2O3
by oxidizing Pd-bound sulfide.
Abstract: In this study, an ablation, mechanical and thermal properties of a rocket motor insulation from phenolic/ fiber matrix composites forming a laminate with different fiber between fiberglass and locally available synthetic fibers. The phenolic/ fiber matrix composites was mechanics and thermal properties by means of tensile strength, ablation, TGA and DSC. The design of thermal insulation involves several factors.Determined the mechanical properties according to MIL-I-24768: Density >1.3 g/cm3, Tensile strength >103 MPa and Ablation
Abstract: IP multicasting is a key technology for many existing and emerging applications on the Internet. Furthermore, with increasing popularity of wireless devices and mobile equipment, it is necessary to determine the best way to provide this service in a wireless environment. IETF Mobile IP, that provides mobility for hosts in IP networks, proposes two approaches for mobile multicasting, namely, remote subscription (MIP-RS) and bi-directional tunneling (MIP-BT). In MIP-RS, a mobile host re-subscribes to the multicast groups each time it moves to a new foreign network. MIP-RS suffers from serious packet losses while mobile host handoff occurs. In MIP-BT, mobile hosts send and receive multicast packets by way of their home agents (HAs), using Mobile IP tunnels. Therefore, it suffers from inefficient routing and wastage of system resources. In this paper, we propose a protocol called Mobile Multicast support using Old Foreign Agent (MMOFA) for Mobile Hosts. MMOFA is derived from MIP-RS and with the assistance of Mobile host's Old foreign agent, routes the missing datagrams due to handoff in adjacent network via tunneling. Also, we studied the performance of the proposed protocol by simulation under ns-2.27. The results demonstrate that MMOFA has optimal routing efficiency and low delivery cost, as compared to other approaches.
Abstract: Several models have been introduced so far for single
electron box, SEB, which all of them were restricted to DC response
and or low temperature limit. In this paper we introduce a new time
dependent, high temperature analytical model for SEB for the first
time. DC behavior of the introduced model will be verified against
SIMON software and its time behavior will be verified against a
newly published paper regarding step response of SEB.
Abstract: In this paper, a methodology of a model based on
predicting the tool forces oblique machining are introduced by
adopting the orthogonal technique. The applied analytical calculation
is mostly based on Devries model and some parts of the methodology
are employed from Amareggo-Brown model. Model validation is
performed by comparing experimental data with the prediction results
on machining titanium alloy (Ti-6Al-4V) based on micro-cutting tool
perspective. Good agreements with the experiments are observed. A
detailed friction form that affected the tool forces also been examined
with reasonable results obtained.
Abstract: Multiprocessor task scheduling is a NP-hard problem and Genetic Algorithm (GA) has been revealed as an excellent technique for finding an optimal solution. In the past, several methods have been considered for the solution of this problem based on GAs. But, all these methods consider single criteria and in the present work, minimization of the bi-criteria multiprocessor task scheduling problem has been considered which includes weighted sum of makespan & total completion time. Efficiency and effectiveness of genetic algorithm can be achieved by optimization of its different parameters such as crossover, mutation, crossover probability, selection function etc. The effects of GA parameters on minimization of bi-criteria fitness function and subsequent setting of parameters have been accomplished by central composite design (CCD) approach of response surface methodology (RSM) of Design of Experiments. The experiments have been performed with different levels of GA parameters and analysis of variance has been performed for significant parameters for minimisation of makespan and total completion time simultaneously.
Abstract: Post growth annealing of solution grown ZnO
nanowire array is performed under controlled oxygen ambience. The
role of annealing over surface defects and their consequence on
dark/photo-conductivity and photosensitivity of nanowire array is
investigated. Surface defect properties are explored using various
measurement tools such as contact angle, photoluminescence, Raman
spectroscopy and XPS measurements. The contact angle of the NW
films reduces due to oxygen annealing and nanowire film surface
changes from hydrophobic (96°) to hydrophilic (16°). Raman and
XPS spectroscopy reveal that oxygen annealing improves the crystal
quality of the nanowire films. The defect band emission intensity
(relative to band edge emission, ID/IUV) reduces from 1.3 to 0.2 after
annealing at 600 °C at 10 SCCM flow of oxygen. An order
enhancement in dark conductivity is observed in O2 annealed
samples, while photoconductivity is found to be slightly reduced due
to lower concentration of surface related oxygen defects.
Abstract: Gas hydrates can agglomerate and block multiphase oil and gas pipelines when water is present at hydrate forming conditions. Using "Cold Flow Technology", the aim is to condition gas hydrates so that they can be transported as a slurry mixture without a risk of agglomeration. During the pipeline shut down however, hydrate particles may settle in bends and build hydrate plugs. An experimental setup has been designed and constructed to study the flow of such plugs at start up operations. Experiments have been performed using model fluid and model hydrate particles. The propagations of initial plugs in a bend were recorded with impedance probes along the pipe. The experimental results show a dispersion of the plug front. A peak in pressure drop was also recorded when the plugs were passing the bend. The evolutions of the plugs have been simulated by numerical integration of the incompressible mass balance equations, with an imposed mixture velocity. The slip between particles and carrier fluid has been calculated using a drag relation together with a particle-fluid force balance.
Abstract: Shear-layer instabilities of a pulsed stack-issued
transverse jet were studied experimentally in a wind tunnel. Jet
pulsations were induced by means of acoustic excitation. Streak
pictures of the smoke-flow patterns illuminated by the laser-light sheet
in the median plane were recorded with a high-speed digital camera.
Instantaneous velocities of the shear-layer instabilities in the flow were
digitized by a hot-wire anemometer. By analyzing the streak pictures
of the smoke-flow visualization, three characteristic flow modes,
synchronized flapping jet, transition, and synchronized shear-layer
vortices, are identified in the shear layer of the pulsed stack-issued
transverse jet at various excitation Strouhal numbers. The shear-layer
instabilities of the pulsed stack-issued transverse jet are synchronized
by acoustic excitation except for transition mode. In transition flow
mode, the shear-layer vortices would exhibit a frequency that would be
twice as great as the acoustic excitation frequency.
Abstract: Compacted clay liners (CCLs) are the main materials
used in waste disposal landfills due to their low permeability. In this
study, the effect on the shear resistant of clays with inorganic salt
solutions as permeate fluid was experimentally investigated. For this
purpose, NaCl inorganic salt solution at concentrations of 2, 5, 10%
and deionized water were used. Laboratory direct shear and Vane
shear tests were conducted on three compacted clays with low,
medium and high plasticity. Results indicated that the solutions type
and its concentration affect the shear properties of the mixture. In the
light of this study, the influence magnitude of these inorganic salts in
varies concentrations in different clays were determined and more
suitable compacted clay with the compare of plasticity were found.
Abstract: Bluetooth is a personal wireless communication
technology and is being applied in many scenarios. It is an emerging
standard for short range, low cost, low power wireless access
technology. Current existing MAC (Medium Access Control)
scheduling schemes only provide best-effort service for all masterslave
connections. It is very challenging to provide QoS (Quality of
Service) support for different connections due to the feature of
Master Driven TDD (Time Division Duplex). However, there is no
solution available to support both delay and bandwidth guarantees
required by real time applications. This paper addresses the issue of
how to enhance QoS support in a Bluetooth piconet. The Bluetooth
specification proposes a Round Robin scheduler as possible solution
for scheduling the transmissions in a Bluetooth Piconet. We propose
an algorithm which will reduce the bandwidth waste and enhance the
efficiency of network. We define token counters to estimate traffic of
real-time slaves. To increase bandwidth utilization, a back-off
mechanism is then presented for best-effort slaves to decrease the
frequency of polling idle slaves. Simulation results demonstrate that
our scheme achieves better performance over the Round Robin
scheduling.
Abstract: A novel sponge submerged membrane bioreactor
(SSMBR) was developed to effectively remove organics and
nutrients from wastewater. Sponge is introduced within the SSMBR
as a medium for the attached growth of biomass. This paper evaluates
the effects of new and acclimatized sponges for dissolved organic
carbon (DOC) removal from wastewater at different mixed liquor
suspended solids- (MLSS) concentration of the sludge. It was
observed in a series of experimental studies that the acclimatized
sponge performed better than the new sponge whilst the optimum
DOC removal could be achieved at 10g/L of MLSS with the
acclimatized sponge. Moreover, the paper analyses the relationships
between the MLSSsponge/MLSSsludge and the DOC removal efficiency
of SSMBR. The results showed a non-linear relationship between the
biomass parameters of the sponge and the sludge, and the DOC
removal efficiency of SSMBR. A second-order polynomial function
could reasonably represent these relationships.
Abstract: In this paper, the signal transmission analysis of the
semicircle-shaped via structure for the differential pairs is presented in
the frequency range up to 10 GHz. In order to improve the signal
transmission properties in the differential pairs, single via is separated
centrally into two semicircle-shaped sections, which are
interconnected with the traces of differential pairs respectively. This
via structure make possible to route differential pairs using only one
via. In addition, it can improve impedance discontinuity around its
region and then enhance the signal transmission properties in the
differential pairs. The electrical analysis such as S-parameter
calculation and eye diagram simulation has been performed to
investigate the improvement of the signal transmission property in the
differential pairs with new via structure.
Abstract: In this paper we study a system composed by carbon
nanotube (CNT) and bundle of carbon nanotube (BuCNT) interacting
with a specific fatty acid as molecular probe. Full system is
represented by open nanotube (or nanotubes) and the linoleic acid
(LA) relaxing due the interaction with CNT and BuCNT. The LA has
in his form an asymmetric shape with COOH termination provoking
a close BuCNT interaction mainly by van der Waals force field. The
simulations were performed by classical molecular dynamics with
standard parameterizations.
Our results show that these BuCNT and CNT are dynamically
stable and it shows a preferential interaction position with LA
resulting in three features: (i) when the LA is interacting with CNT
and BuCNT (including both termination, CH2 or COOH), the LA is
repelled; (ii) when the LA terminated with CH2 is closer to open
extremity of BuCNT, the LA is also repelled by the interaction
between them; and (iii) when the LA terminated with COOH is
closer to open extremity of BuCNT, the LA is encapsulated by the
BuCNT. These simulations are part of a more extensive work on
searching efficient selective molecular devices and could be useful to
reach this goal.
Abstract: The development of the signal compression
algorithms is having compressive progress. These algorithms are
continuously improved by new tools and aim to reduce, an average,
the number of bits necessary to the signal representation by means of
minimizing the reconstruction error. The following article proposes
the compression of Arabic speech signal by a hybrid method
combining the wavelet transform and the linear prediction. The
adopted approach rests, on one hand, on the original signal
decomposition by ways of analysis filters, which is followed by the
compression stage, and on the other hand, on the application of the
order 5, as well as, the compression signal coefficients. The aim of
this approach is the estimation of the predicted error, which will be
coded and transmitted. The decoding operation is then used to
reconstitute the original signal. Thus, the adequate choice of the
bench of filters is useful to the transform in necessary to increase the
compression rate and induce an impercevable distortion from an
auditive point of view.
Abstract: The fluid mechanics principle is used extensively in
designing axial flow fans and their associated equipment. This paper presents a computational fluid dynamics (CFD) modeling of air flow
distribution from a radiator axial flow fan used in an acid pump truck Tier4 (APT T4) Repower. This axial flow fan augments the transfer
of heat from the engine mounted on the APT T4.
CFD analysis was performed for an area weighted average static pressure difference at the inlet and outlet of the fan. Pressure contours, velocity vectors, and path lines were plotted for detailing
the flow characteristics for different orientations of the fan blade. The results were then compared and verified against known theoretical observations and actual experimental data. This study
shows that a CFD simulation can be very useful for predicting and understanding the flow distribution from a radiator fan for further
research work.
Abstract: In this paper, cloud resource broker using goalbased
request in medical application is proposed. To handle recent
huge production of digital images and data in medical informatics
application, the cloud resource broker could be used by medical
practitioner for proper process in discovering and selecting correct
information and application. This paper summarizes several
reviewed articles to relate medical informatics application with
current broker technology and presents a research work in applying
goal-based request in cloud resource broker to optimize the use of
resources in cloud environment. The objective of proposing a new
kind of resource broker is to enhance the current resource
scheduling, discovery, and selection procedures. We believed that
it could help to maximize resources allocation in medical
informatics application.
Abstract: The social force model which belongs to the
microscopic pedestrian studies has been considered as the supremacy
by many researchers and due to the main feature of reproducing the
self-organized phenomena resulted from pedestrian dynamic. The
Preferred Force which is a measurement of pedestrian-s motivation to
adapt his actual velocity to his desired velocity is an essential term on
which the model was set up. This Force has gone through stages of
development: first of all, Helbing and Molnar (1995) have modeled
the original force for the normal situation. Second, Helbing and his
co-workers (2000) have incorporated the panic situation into this
force by incorporating the panic parameter to account for the panic
situations. Third, Lakoba and Kaup (2005) have provided the
pedestrians some kind of intelligence by incorporating aspects of the
decision-making capability. In this paper, the authors analyze the
most important incorporations into the model regarding the preferred
force. They make comparisons between the different factors of these
incorporations. Furthermore, to enhance the decision-making ability
of the pedestrians, they introduce additional features such as the
familiarity factor to the preferred force to let it appear more
representative of what actually happens in reality.
Abstract: This article proposes an Ant Colony Optimization
(ACO) metaheuristic to minimize total makespan for scheduling a set
of jobs and assign workers for uniformly related parallel machines.
An algorithm based on ACO has been developed and coded on a
computer program Matlab®, to solve this problem. The paper
explains various steps to apply Ant Colony approach to the problem
of minimizing makespan for the worker assignment & jobs
scheduling problem in a parallel machine model and is aimed at
evaluating the strength of ACO as compared to other conventional
approaches. One data set containing 100 problems (12 Jobs, 03
machines and 10 workers) which is available on internet, has been
taken and solved through this ACO algorithm. The results of our
ACO based algorithm has shown drastically improved results,
especially, in terms of negligible computational effort of CPU, to
reach the optimal solution. In our case, the time taken to solve all 100
problems is even lesser than the average time taken to solve one
problem in the data set by other conventional approaches like GA
algorithm and SPT-A/LMC heuristics.
Abstract: The objective of this paper is to analyze the
performance of a double-sided axial flux permanent magnet
brushless DC (AFPM BLDC) motor with two-phase winding.
To study the motor operation, a mathematical dynamic model
has been proposed for motor, which became the basis for
simulations that were performed using MATLAB/SIMULINK
software package. The results of simulations were presented
in form of the waveforms of selected quantities and the
electromechanical characteristics performed by the motor. The
calculation results show that the two-phase motor version
develops smooth torque and reaches high efficiency. The twophase
motor can be applied where more smooth torque is
required. Finally a study on the influence of switching angle
on motor performance shows that when advance switching
technique is used, the motor operates with the highest
efficiency.