Abstract: In the context of sensor networks, where every few
dB saving counts, the novel node cooperation schemes are reviewed
where MIMO techniques play a leading role. These methods could be
treated as joint approach for designing physical layer of their
communication scenarios. Then we analyzed the BER performance
of transmission diversity schemes under a general fading channel
model and proposed a power allocation strategy to the transmitting
sensor nodes. This approach is then compared to an equal-power
assignment method and its performance enhancement is verified by
the simulation. Another key point of the contribution lies in the
combination of optimal power allocation and sensor nodes-
cooperation in a transmission diversity regime (MISO). Numerical
results are given through figures to demonstrate the optimality and
efficiency of proposed combined approach.
Abstract: The paper introduces and discusses definitions and concepts from the supplier relationship management area. This review has the goal to provide readers with the basic conditions to understand the market mechanisms and the technological developments of the SRM market. Further on, the work gives a picture of the actual business environment in which the SRM vendors are in, and the main trends in the field, based on the main SRM functionalities i.e. e-Procurement, e-Sourcing and Supplier Enablement, which indicates users and software providers the future technological developments and practises that will take place in this area in the next couple of years.
Abstract: The development and extension of large cities induced
a need for shallow tunnel in soft ground of building areas. Estimation
of ground settlement caused by the tunnel excavation is important
engineering point. In this paper, prediction of surface subsidence
caused by tunneling in one section of seventh line of Tehran subway
is considered. On the basis of studied geotechnical conditions of the
region, tunnel with the length of 26.9km has been excavated applying
a mechanized method using an EPB-TBM with a diameter of 9.14m.
In this regard, settlement is estimated utilizing both analytical and
numerical finite element method. The numerical method shows that
the value of settlement in this section is 5cm. Besides, the analytical
consequences (Bobet and Loganathan-Polous) are 5.29 and 12.36cm,
respectively. According to results of this study, due tosaturation of
this section, there are good agreement between Bobet and numerical
methods. Therefore, tunneling processes in this section needs a
special consolidation measurement and support system before the
passage of tunnel boring machine.
Abstract: Coated tool inserts can be considered as the backbone
of machining processes due to their wear and heat resistance.
However, defects of coating can degrade the integrity of these inserts
and the number of these defects should be minimized or eliminated if
possible. Recently, the advancement of coating processes and
analytical tools open a new era for optimizing the coating tools.
First, an overview is given regarding coating technology for cutting
tool inserts. Testing techniques for coating layers properties, as well
as the various coating defects and their assessment are also surveyed.
Second, it is introduced an experimental approach to examine the
possible coating defects and flaws of worn multicoated carbide
inserts using two important techniques namely scanning electron
microscopy and atomic force microscopy. Finally, it is
recommended a simple procedure for investigating manufacturing
defects and flaws of worn inserts.
Abstract: This paper presents a design and prototype
implementation of new home automation system that uses WiFi
technology as a network infrastructure connecting its parts. The
proposed system consists of two main components; the first part is
the server (web server), which presents system core that manages,
controls, and monitors users- home. Users and system administrator
can locally (LAN) or remotely (internet) manage and control system
code. Second part is hardware interface module, which provides
appropriate interface to sensors and actuator of home automation
system. Unlike most of available home automation system in the
market the proposed system is scalable that one server can manage
many hardware interface modules as long as it exists on WiFi
network coverage. System supports a wide range of home
automation devices like power management components, and
security components. The proposed system is better from the
scalability and flexibility point of view than the commercially
available home automation systems.
Abstract: This paper introduces and studies new indexing techniques for content-based queries in images databases. Indexing is the key to providing sophisticated, accurate and fast searches for queries in image data. This research describes a new indexing approach, which depends on linear modeling of signals, using bases for modeling. A basis is a set of chosen images, and modeling an image is a least-squares approximation of the image as a linear combination of the basis images. The coefficients of the basis images are taken together to serve as index for that image. The paper describes the implementation of the indexing scheme, and presents the findings of our extensive evaluation that was conducted to optimize (1) the choice of the basis matrix (B), and (2) the size of the index A (N). Furthermore, we compare the performance of our indexing scheme with other schemes. Our results show that our scheme has significantly higher performance.
Abstract: Training neural networks to capture an intrinsic
property of a large volume of high dimensional data is a difficult
task, as the training process is computationally expensive. Input
attributes should be carefully selected to keep the dimensionality of
input vectors relatively small.
Technical indexes commonly used for stock market prediction
using neural networks are investigated to determine its effectiveness
as inputs. The feed forward neural network of Levenberg-Marquardt
algorithm is applied to perform one step ahead forecasting of
NASDAQ and Dow stock prices.
Abstract: In this paper, the decomposition-aggregation method
is used to carry out connective stability criteria for general linear
composite system via aggregation. The large scale system is
decomposed into a number of subsystems. By associating directed
graphs with dynamic systems in an essential way, we define the
relation between system structure and stability in the sense of
Lyapunov. The stability criteria is then associated with the stability
and system matrices of subsystems as well as those interconnected
terms among subsystems using the concepts of vector differential
inequalities and vector Lyapunov functions. Then, we show that the
stability of each subsystem and stability of the aggregate model
imply connective stability of the overall system. An example is
reported, showing the efficiency of the proposed technique.
Abstract: Air emissions from waste treatment plants often
consist of a combination of Volatile Organic Compounds (VOCs)
and odors. Hydrogen sulfide is one of the major odorous gases
present in the waste emissions coming from municipal wastewater
treatment facilities. Hydrogen sulfide (H2S) is odorous, highly toxic
and flammable. Exposure to lower concentrations can result in eye
irritation, a sore throat and cough, shortness of breath, and fluid in
the lungs. Biofiltration has become a widely accepted technology for
treating air streams containing H2S. When compared with other nonbiological
technologies, biofilter is more cost-effective for treating large
volumes of air containing low concentrations of biodegradable compounds.
Optimization of biofilter media is essential for many reasons such as:
providing a higher surface area for biofilm growth, low pressure drop,
physical stability, and good moisture retention. In this work, a novel
biofilter media is developed and tested at a pumping station of a
municipality located in the United Arab Emirates (UAE). The
media is found to be very effective (>99%) in removing H2S
concentrations that are expected in pumping stations under steady
state and shock loading conditions.
Abstract: Society has grown to rely on Internet services, and the
number of Internet users increases every day. As more and more
users become connected to the network, the window of opportunity
for malicious users to do their damage becomes very great and
lucrative. The objective of this paper is to incorporate different
techniques into classier system to detect and classify intrusion from
normal network packet. Among several techniques, Steady State
Genetic-based Machine Leaning Algorithm (SSGBML) will be used
to detect intrusions. Where Steady State Genetic Algorithm (SSGA),
Simple Genetic Algorithm (SGA), Modified Genetic Algorithm and
Zeroth Level Classifier system are investigated in this research.
SSGA is used as a discovery mechanism instead of SGA. SGA
replaces all old rules with new produced rule preventing old good
rules from participating in the next rule generation. Zeroth Level
Classifier System is used to play the role of detector by matching
incoming environment message with classifiers to determine whether
the current message is normal or intrusion and receiving feedback
from environment. Finally, in order to attain the best results,
Modified SSGA will enhance our discovery engine by using Fuzzy
Logic to optimize crossover and mutation probability. The
experiments and evaluations of the proposed method were performed
with the KDD 99 intrusion detection dataset.
Abstract: The rapid urbanization of cities has a bane in the form
road accidents that cause extensive damage to life and limbs. A
number of location based factors are enablers of road accidents in the
city. The speed of travel of vehicles is non-uniform among locations
within a city. In this study, the perception of vehicle users is captured
on a 10-point rating scale regarding the degree of variation in speed
of travel at chosen locations in the city. The average rating is used to
cluster locations using fuzzy c-means clustering and classify them as
low, moderate and high speed of travel locations. The high speed of
travel locations can be classified proactively to ensure that accidents
do not occur due to the speeding of vehicles at such locations. The
advantage of fuzzy c-means clustering is that a location may be a
part of more than one cluster to a varying degree and this gives a
better picture about the location with respect to the characteristic
(speed of travel) being studied.
Abstract: This paper proposes a method of adaptively generating a gait pattern of biped robot. The gait synthesis is based on human's gait pattern analysis. The proposed method can easily be applied to generate the natural and stable gait pattern of any biped robot. To analyze the human's gait pattern, sequential images of the human's gait on the sagittal plane are acquired from which the gait control values are extracted. The gait pattern of biped robot on the sagittal plane is adaptively generated by a genetic algorithm using the human's gait control values. However, gait trajectories of the biped robot on the sagittal plane are not enough to construct the complete gait pattern because the biped robot moves on 3-dimension space. Therefore, the gait pattern on the frontal plane, generated from Zero Moment Point (ZMP), is added to the gait one acquired on the sagittal plane. Consequently, the natural and stable walking pattern for the biped robot is obtained.
Abstract: In this paper we analyze the core issues affecting
software architecture in enterprise projects where a large number of
people at different backgrounds are involved and complex business,
management and technical problems exist. We first give general
features of typical enterprise projects and then present foundations of
software architectures. The detailed analysis of core issues affecting
software architecture in software development phases is given. We
focus on three main areas in each development phase: people,
process, and management related issues, structural (product) issues,
and technology related issues. After we point out core issues and
problems in these main areas, we give recommendations for
designing good architecture. We observed these core issues and the
importance of following the best software development practices and
also developed some novel practices in many big enterprise
commercial and military projects in about 10 years of experience.
Abstract: An electrocardiogram (ECG) feature extraction system
based on the calculation of the complex resonance frequency
employing Prony-s method is developed. Prony-s method is applied
on five different classes of ECG signals- arrhythmia as a finite sum
of exponentials depending on the signal-s poles and the resonant
complex frequencies. Those poles and resonance frequencies of the
ECG signals- arrhythmia are evaluated for a large number of each
arrhythmia. The ECG signals of lead II (ML II) were taken from
MIT-BIH database for five different types. These are the ventricular
couplet (VC), ventricular tachycardia (VT), ventricular bigeminy
(VB), and ventricular fibrillation (VF) and the normal (NR). This
novel method can be extended to any number of arrhythmias.
Different classification techniques were tried using neural networks
(NN), K nearest neighbor (KNN), linear discriminant analysis (LDA)
and multi-class support vector machine (MC-SVM).
Abstract: Condition monitoring of electrical power equipment
has attracted considerable attention for many years. The aim of this
paper is to use Labview with Fuzzy Logic controller to build a
simulation system to diagnose transformer faults and monitor its
condition. The front panel of the system was designed using
LabVIEW to enable computer to act as customer-designed
instrument. The dissolved gas-in-oil analysis (DGA) method was
used as technique for oil type transformer diagnosis; meanwhile
terminal voltages and currents analysis method was used for dry type
transformer. Fuzzy Logic was used as expert system that assesses all
information keyed in at the front panel to diagnose and predict the
condition of the transformer. The outcome of the Fuzzy Logic
interpretation will be displayed at front panel of LabVIEW to show
the user the conditions of the transformer at any time.
Abstract: In this paper, creep constitutive equations of base
(Parent) and weld materials of the weldment for cold-drawn 304L
stainless steel have been obtained experimentally. For this purpose,
test samples have been generated from cold drawn bars and weld
material according to the ASTM standard. The creep behavior and
properties have been examined for these materials by conducting uniaxial
creep tests. Constant temperatures and constant load uni-axial
creep tests have been carried out at two high temperatures, 680 and
720 oC, subjected to constant loads, which produce initial stresses
ranging from 240 to 360 MPa. The experimental data have been used
to obtain the creep constitutive parameters using numerical
optimization techniques.
Abstract: The segmentation of endovascular tools in fluoroscopy images can be accurately performed automatically or by minimum user intervention, using known modern techniques. It has been proven in literature, but no clinical implementation exists so far because the computational time requirements of such technology have not yet been met. A classical segmentation scheme is composed of edge enhancement filtering, line detection, and segmentation. A new method is presented that consists of a vector that propagates in the image to track an edge as it advances. The filtering is performed progressively in the projected path of the vector, whose orientation allows for oriented edge detection, and a minimal image area is globally filtered. Such an algorithm is rapidly computed and can be implemented in real-time applications. It was tested on medical fluoroscopy images from an endovascular cerebral intervention. Ex- periments showed that the 2D tracking was limited to guidewires without intersection crosspoints, while the 3D implementation was able to cope with such planar difficulties.
Abstract: Applicability of tuning the controller gains for Stewart manipulator using genetic algorithm as an efficient search technique is investigated. Kinematics and dynamics models were introduced in detail for simulation purpose. A PD task space control scheme was used. For demonstrating technique feasibility, a Stewart manipulator numerical-model was built. A genetic algorithm was then employed to search for optimal controller gains. The controller was tested onsite a generic circular mission. The simulation results show that the technique is highly convergent with superior performance operating for different payloads.
Abstract: Radio-frequency identification has entered as a beneficial means with conforming GS1 standards to provide the best solutions in the manufacturing area. It competes with other automated identification technologies e.g. barcodes and smart cards with regard to high speed scanning, reliability and accuracy as well. The purpose of this study is to improve production line-s performance by implementing RFID system in the manufacturing area on the basis of radio-frequency identification (RFID) system by 3D modeling in the program Cinema 4D R13 which provides obvious graphical scenes for users to portray their applications. Finally, with regard to improving system performance, it shows how RFID appears as a well-suited technology in a comparison of the barcode scanner to handle different kinds of raw materials in the production line base on logical process.
Abstract: In this study we applied thermal lens (TL) technique
to study the effect of size on thermal diffusivity of cadmium sulphide
(CdS) nanofluid prepared by using γ-radiation method containing
particles with different sizes. In TL experimental set up a diode laser
of wavelength 514 nm and intensity stabilized He-Ne laser were used
as the excitation source and the probe beam respectively,
respectively. The experimental results showed that the thermal
diffusivity value of CdS nanofluid increases when the of particle size
increased.