Abstract: The major objective of this study is to understand the
potential of a newly fabricated equipment to study the thermal
properties of nonwoven textile fabrics treated with aerogel at subzero
temperatures. Thermal conductivity was calculated by using the
empirical relation Fourier’s law, The relationship between the
thermal conductivity and thermal resistance of the samples were
studied at various environmental temperatures (which was set in the
clima temperature system between +25oC to -25oC). The newly
fabricated equipment was found to be a suitable for measuring at
subzero temperatures. This field of measurements is being developed
and will be the subject of further research which will be more suitable
for measurement of the various thermal characteristics.
Abstract: Cyclic delay diversity (CDD) is a simple technique to
intentionally increase frequency selectivity of channels for orthogonal
frequency division multiplexing (OFDM).This paper proposes a residual
carrier frequency offset (RFO) estimation scheme for OFDMbased
broadcasting system using CDD. In order to improve the RFO
estimation, this paper addresses a decision scheme of the amount of
cyclic delay and pilot pattern used to estimate the RFO. By computer
simulation, the proposed estimator is shown to benefit form propoerly
chosen delay parameter and perform robustly.
Abstract: White scar oyster (Crassostrea belcheri) is often eaten
raw and being the leading vehicle for foodborne disease, especially
Salmonella Weltevreden which exposed the prominent and most
resistant to radiation. Gamma irradiation at a low dose of 1 kGy was
enough to eliminate S. Weltevreden contaminated in oyster meat at a
level up to 5 log CFU/g while it still retain the raw characteristics and
equivalent sensory quality as the non-irradiated one. Process
development of ready-to-eat chilled oyster meat was conducted by
shucking the meat, individually packed in plastic bags, subjected to 1
kGy gamma radiation at chilled condition and then stored in 4oC
refrigerated temperature. Microbiological determination showed the
absence of S. Weltevreden (5 log CFU/g initial inoculated) along the
whole storage time of 30 days. Sensory evaluation indicated the
decreasing in sensory scores along storage time which determining
the product shelf life to be 18 days compared to 15 days of nonirradiated
one. The most advantage of developed process was to
provide the safe raw oyster to consumers and in addition sensory
quality retained and 3-day extension shelf life also exist.
Abstract: The huge development of new technologies and the
apparition of open communication system more and more
sophisticated create a new challenge to protect digital content from
piracy. Digital watermarking is a recent research axis and a new
technique suggested as a solution to these problems. This technique
consists in inserting identification information (watermark) into
digital data (audio, video, image, databases...) in an invisible and
indelible manner and in such a way not to degrade original medium-s
quality. Moreover, we must be able to correctly extract the
watermark despite the deterioration of the watermarked medium (i.e
attacks). In this paper we propose a system for watermarking satellite
images. We chose to embed the watermark into frequency domain,
precisely the discrete wavelet transform (DWT). We applied our
algorithm on satellite images of Tunisian center. The experiments
show satisfying results. In addition, our algorithm showed an
important resistance facing different attacks, notably the compression
(JEPG, JPEG2000), the filtering, the histogram-s manipulation and
geometric distortions such as rotation, cropping, scaling.
Abstract: Firstly, this study briefly presents the current situation that there exists a vast gap between current Chinese and Japanese seismic design specification for bridge pile foundation in liquefiable and liquefaction-induced lateral spreading ground; The Chinese and Japanese seismic design method and technical detail for bridge pile foundation in liquefying and lateral spreading ground are described and compared systematically and comprehensively, the methods of determining coefficient of subgrade reaction and its reduction factor as well as the computing mode of the applied force on pile foundation due to liquefaction-induced lateral spreading soil in Japanese design specification are especially introduced. Subsequently, the comparison indicates that the content of Chinese seismic design specification for bridge pile foundation in liquefiable and liquefaction-induced lateral spreading ground, just presenting some qualitative items, is too general and lacks systematicness and maneuverability. Finally, some defects of seismic design specification in China are summarized, so the improvement and revision of specification in the field turns out to be imperative for China, some key problems of current Chinese specifications are generalized and the corresponding improvement suggestions are proposed.
Abstract: The author present PID controller design for
following control of hard disk drive by characteristic ratio assignment
method. The study in this paper concerns design of a PID controller
which sufficiently robust to the disturbances and plant perturbations
on following control of hard disk drive. Characteristic Ratio
Assignment (CRA) is shown to be an efficient control technique to
serve this requirement. The controller design by CRA is based on the
choice of the coefficients of the characteristic polynomial of the
closed loop system according to the convenient performance criteria
such as equivalent time constant and ration of characteristic
coefficient. Hence, in this study, CRA method is applied in PID
controller design for following control of hard disk drive. Matlab
simulation results shown that CRA design is fairly stable and robust
whilst giving the convenience in controller-s parameters adjustment.
Abstract: In recent years, we see an increase of interest for efficient tracking systems in surveillance applications. Many of the proposed techniques are designed for static cameras environments. When the camera is moving, tracking moving objects become more difficult and many techniques fail to detect and track the desired targets. The problem becomes more complex when we want to track a specific object in real-time using a moving Pan and Tilt camera system to keep the target within the image. This type of tracking is of high importance in surveillance applications. When a target is detected at a certain zone, the possibility of automatically tracking it continuously and keeping it within the image until action is taken is very important for security personnel working in very sensitive sites. This work presents a real-time tracking system permitting the detection and continuous tracking of targets using a Pan and Tilt camera platform. A novel and efficient approach for dealing with occlusions is presented. Also a new intelligent forget factor is introduced in order to take into account target shape variations and avoid learning non desired objects. Tests conducted in outdoor operational scenarios show the efficiency and robustness of the proposed approach.
Abstract: With the drastically growth in optical communication
technology, a lossless, low-crosstalk and multifunction optical switch
is most desirable for large-scale photonic network. To realize such a
switch, we have introduced the new architecture of optical switch
that embedded many functions on single device. The asymmetrical
architecture of OXADM consists of 3 parts; selective port, add/drop
operation, and path routing. Selective port permits only the interest
wavelength pass through and acts as a filter. While add and drop
function can be implemented in second part of OXADM architecture.
The signals can then be re-routed to any output port or/and perform
an accumulation function which multiplex all signals onto single path
and then exit to any interest output port. This will be done by path
routing operation. The unique features offered by OXADM has
extended its application to Fiber to-the Home Technology (FTTH),
here the OXADM is used as a wavelength management element in
Optical Line Terminal (OLT). Each port is assigned specifically with
the operating wavelengths and with the dynamic routing management
to ensure no traffic combustion occurs in OLT.
Abstract: In this paper we have proposed a novel dynamic least cost multicast routing protocol using hybrid genetic algorithm for IP networks. Our protocol finds the multicast tree with minimum cost subject to delay, degree, and bandwidth constraints. The proposed protocol has the following features: i. Heuristic local search function has been devised and embedded with normal genetic operation to increase the speed and to get the optimized tree, ii. It is efficient to handle the dynamic situation arises due to either change in the multicast group membership or node / link failure, iii. Two different crossover and mutation probabilities have been used for maintaining the diversity of solution and quick convergence. The simulation results have shown that our proposed protocol generates dynamic multicast tree with lower cost. Results have also shown that the proposed algorithm has better convergence rate, better dynamic request success rate and less execution time than other existing algorithms. Effects of degree and delay constraints have also been analyzed for the multicast tree interns of search success rate.
Abstract: The nanofiber sheet of Multiwall Cabon Nanotube
(MWCNTs)/Polyacylonitile (PAN) composites was fabricated from
electrospun nanofiber. Firstly the surface of MWCNTs was
chemically modified, comparing two different techniques consisting
of admicellar polymerization and functionalization to improve the
dispersion and prevent the aggregation in the PAN matrix. The
modified MWCNTs were characterized by the dispersion in
dimethylformamide (DMF) solvent, Laser particle size, and FTRaman.
Lastly, DSC, SEM and mechanical properties of the
nanofiber sheet were examined. The results show that the mechanical
properties of the nanofiber sheet prepared from admicellar
polymerization-modified MWCNTs were higher than those of the
others.
Abstract: Effective cooling of electronic equipment has emerged
as a challenging and constraining problem of the new century. In the
present work the feasibility and effectiveness of jet impingement
cooling on electronics were investigated numerically and
experimentally. Studies have been conducted to see the effect of the
geometrical parameters such as jet diameter (D), jet to target
spacing (Z) and ratio of jet spacing to jet diameter (Z/D) on the heat
transfer characteristics. The values of Reynolds numbers considered
are in the range 7000 to 42000. The results obtained from the
numerical studies are validated by conducting experiments. From the
studies it is found that the optimum value of Z/D ratio is 5. For a
given Reynolds number, the Nusselt number increases by about 28%
if the diameter of the nozzle is increased from 1mm to 2mm.
Correlations are proposed for Nusselt number in terms of Reynolds
number and these are valid for air as the cooling medium.
Abstract: Field mapping activity for an active volcano mainly in
the Torrid Zone is usually hampered by several problems such as steep
terrain and bad atmosphere conditions. In this paper we present a
simple solution for such problem by a combination Synthetic Aperture
Radar (SAR) and geostatistical methods. By this combination, we
could reduce the speckle effect from the SAR data and then estimate
roughness distribution of the pyroclastic flow deposits. The main
purpose of this study is to detect spatial distribution of new pyroclastic
flow deposits termed as P-zone accurately using the β°data from two
RADARSAT-1 SAR level-0 data. Single scene of Hyperion data and
field observation were used for cross-validation of the SAR results.
Mt. Merapi in central Java, Indonesia, was chosen as a study site and
the eruptions in May-June 2006 were examined. The P-zones were
found in the western and southern flanks. The area size and the longest
flow distance were calculated as 2.3 km2 and 6.8 km, respectively. The
grain size variation of the P-zone was mapped in detail from fine to
coarse deposits regarding the C-band wavelength of 5.6 cm.
Abstract: Phase locked loops (PLL) and delay locked loops (DLL) play an important role in establishing coherent references (phase of carrier and symbol timing) in digital communication systems. Fully digital receiver including digital carrier synchronizer and symbol timing synchronizer fulfils the conditions for universal multi-mode communication receiver with option of symbol rate setting over several digit places and long-term stability of requirement parameters. Afterwards it is necessary to realize PLL and DLL in synchronizer in digital form and to approach to these subsystems as a discrete representation of analog template. Analysis of discrete phase locked loop (DPLL) or discrete delay locked loop (DDLL) and technique to determine their characteristics based on analog (continuous-time) template is performed in this posed paper. There are derived transmission response and error function for 1st order discrete locked loop and resulting equations and graphical representations for 2nd order one. It is shown that the spectrum translation due to sampling takes effect at frequency characteristics computing for specific values of loop parameters.
Abstract: Fully customized hardware based technology provides high performance and low power consumption by specializing the tasks in hardware but lacks design flexibility since any kind of changes require re-design and re-fabrication. Software based solutions operate with software instructions due to which a great flexibility is achieved from the easy development and maintenance of the software code. But this execution of instructions introduces a high overhead in performance and area consumption. In past few decades the reconfigurable computing domain has been introduced which overcomes the traditional trades-off between flexibility and performance and is able to achieve high performance while maintaining a good flexibility. The dramatic gains in terms of chip performance and design flexibility achieved through the reconfigurable computing systems are greatly dependent on the design of their computational units being integrated with reconfigurable logic resources. The computational unit of any reconfigurable system plays vital role in defining its strength. In this research paper an RFU based computational unit design has been presented using the tightly coupled, multi-threaded reconfigurable cores. The proposed design has been simulated for VLIW based architectures and a high gain in performance has been observed as compared to the conventional computing systems.
Abstract: Semantic Web services will enable the semiautomatic
and automatic annotation, advertisement, discovery,
selection, composition, and execution of inter-organization business
logic, making the Internet become a common global platform where
organizations and individuals communicate with each other to carry
out various commercial activities and to provide value-added
services. There is a growing consensus that Web services alone will
not be sufficient to develop valuable solutions due the degree of
heterogeneity, autonomy, and distribution of the Web. This paper
deals with two of the hottest R&D and technology areas currently
associated with the Web – Web services and the Semantic Web. It
presents the synergies that can be created between Web Services and
Semantic Web technologies to provide a new generation of eservices.
Abstract: Image data holds a large amount of different context
information. However, as of today, these resources remain largely
untouched. It is thus the aim of this paper to present a basic technical
framework which allows for a quick and easy exploitation of context
information from image data especially by non-expert users.
Furthermore, the proposed framework is discussed in detail
concerning important social and ethical issues which demand special
requirements in system design. Finally, a first sensor prototype is
presented which meets the identified requirements. Additionally,
necessary implications for the software and hardware design of the
system are discussed, rendering a sensor system which could be
regarded as a good, acceptable and justifiable technical and thereby
enabling the extraction of context information from image data.
Abstract: Process-oriented software development is a new
software development paradigm in which software design is modeled
by a business process which is in turn translated into a process
execution language for execution. The building blocks of this
paradigm are software units that are composed together to work
according to the flow of the business process. This new paradigm
still exhibits the characteristic of the applications built with the
traditional software component technology. This paper discusses an
approach to apply a traditional technique for software component
fabrication to the design of process-oriented software units, called
process components. These process components result from
decomposing a business process of a particular application domain
into subprocesses, and these process components can be reused to
design the business processes of other application domains. The
decomposition considers five managerial goals, namely cost
effectiveness, ease of assembly, customization, reusability, and
maintainability. The paper presents how to design or decompose
process components from a business process model and measure
some technical features of the design that would affect the
managerial goals. A comparison between the measurement values
from different designs can tell which process component design is
more appropriate for the managerial goals that have been set. The
proposed approach can be applied in Web Services environment
which accommodates process-oriented software development.
Abstract: This paper presents preliminary results of a
technology assessment analysis for the use of high pressure treatment
(HPT) on Halloumi cheese. In particular, it presents the importance
of this traditional Cyprus cheese to the island-s economy, explains its
production process, and gives a brief introduction to HPT and its
application on cheese. More importantly, it offers preliminary results
of HPT of Halloumi samples and a preliminary economic feasibility
study on the financial implications of the introduction of such
technology.
Abstract: Microwave energy is a superior alternative to several other thermal treatments. Extraction techniques are widely employed for the isolation of bioactive compounds and vegetable oils from oil seeds. Among the different and new available techniques, microwave pretreatment of seeds is a simple and desirable method for production of high quality vegetable oils. Microwave pretreatment for oil extraction has many advantages as follow: improving oil extraction yield and quality, direct extraction capability, lower energy consumption, faster processing time and reduced solvent levels compared with conventional methods. It allows also for better retention and availability of desirable nutraceuticals, such as phytosterols and tocopherols, canolol and phenolic compounds in the extracted oil such as rapeseed oil. This can be a new step to produce nutritional vegetable oils with improved shelf life because of high antioxidant content.
Abstract: Support Vector Machine (SVM) is a recent class of statistical classification and regression techniques playing an increasing role in applications to detection problems in various engineering problems, notably in statistical signal processing, pattern recognition, image analysis, and communication systems. In this paper, SVM is applied to an infrared (IR) binary communication system with different types of channel models including Ricean multipath fading and partially developed scattering channel with additive white Gaussian noise (AWGN) at the receiver. The structure and performance of SVM in terms of the bit error rate (BER) metric is derived and simulated for these channel stochastic models and the computational complexity of the implementation, in terms of average computational time per bit, is also presented. The performance of SVM is then compared to classical binary signal maximum likelihood detection using a matched filter driven by On-Off keying (OOK) modulation. We found that the performance of SVM is superior to that of the traditional optimal detection schemes used in statistical communication, especially for very low signal-to-noise ratio (SNR) ranges. For large SNR, the performance of the SVM is similar to that of the classical detectors. The implication of these results is that SVM can prove very beneficial to IR communication systems that notoriously suffer from low SNR at the cost of increased computational complexity.