Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: Research results and optimal parameters investigation
of laser cut and profiling of diamond and quartz substrates by
femtosecond laser pulses are presented. Profiles 10 μm in width, ~25
μm in depth and several millimeters long were made. Investigation of
boundaries quality has been carried out with the use of AFM
«Vecco». Possibility of technological formation of profiles and
micro-holes in diamond and quartz substrates with nanometer-scale
boundaries is shown. Experimental results of multilayer dielectric
cover treatment are also presented. Possibility of precise upper layer
(thickness of 70–140 nm) removal is demonstrated. Processes of thin
metal film (60 nm and 350 nm thick) treatment are considered.
Isolation tracks (conductance ~ 10-11 S) 1.6–2.5 μm in width in
conductive metal layers are formed.
Abstract: In this survey the process of crack propagation at the
toe of concrete gravity dam is investigated by applying principals
and criteria of linear elastic fracture mechanic. Simulating process of
earthquake conditions for three models of dam with different
geometrical condition, in empty reservoir under plain stress is
calculated through special fracture mechanic software FRANNC2D
[1] for determining fracture mechanic criteria. The outcomes showed
that in spite of the primary expectations, the simultaneous existence
of fillet in both toe and heel area (model 3), the rate of maximum
principal stress has not been decreased; however, even the maximum
principal stress has increased, so it caused stress intensity factors
increase which is undesirable. On the other hand, the dam with heel
fillet has shown the best attitude and it is because of items like
decreasing the rates of maximum and minimum principal stresses and
also is related to decreasing the rates of stress intensity factors for 1st
& 2nd modes of the model.
Abstract: In recent years Malaysia has included renewable
energy as an alternative fuel to help in diversifying the country-s
energy reliance on oil, natural gas, coal and hydropower with
biomass and solar energy gaining priority. The scope of this paper is
to look at the designing procedures and analysis of a solar thermal
parabolic trough concentrator by simulation utilizing meteorological
data in several parts of Malaysia. Parameters which include the
aperture area, the diameter of the receiver and the working fluid may
be varied to optimize the design. Aperture area is determined by
considering the width and the length of the concentrator whereas the
geometric concentration ratio (CR) is obtained by considering the
width and diameter of the receiver. Three types of working fluid are
investigated. Theoretically, concentration ratios can be very high in
the range of 10 to 40 000 depending on the optical elements used and
continuous tracking of the sun. However, a thorough analysis is
essential as discussed in this paper where optical precision and
thermal analysis must be carried out to evaluate the performance of
the parabolic trough concentrator as the theoretical CR is not the only
factor that should be considered.
Abstract: For smaller mechatronic device, especially for micro
Electronic system, a micro machining is a must. However, most
investigations on vibration of a mill have been limited to the
traditional type mill. In this article, vibration and dynamic
characteristics of a micro mill were investigated in this study. The
trend towards higher precision manufacturing technology requires
producing miniaturized components. To improve micro-milled
product quality, obtain a higher production rate and avoid milling
breakage, the dynamic characteristics of micro milling must be
studied. A stepped pre-twisted mill is used to simulate the micro mill.
The finite element analysis is employed in this work. The flute length
and diameter effects of the micro mill are considered. It is clear that
the effects of micro mill shape parameters on vibration in a micro mill
are significant.
Abstract: Observations show that power plant efficiency
decreases in hot summer days. Water droplet injection in air
condensers is suggested in order to decrease the inlet air temperature.
Nozzle arrangement, injected water flow rate and droplets diameter
effects on evaporation rate and the resulting air temperature are
investigated using numerical simulation. Decreasing the diameter of
injected droplets and increasing the number of injecting nozzles,
decreases the outlet air temperature. Also a more uniform air
temperature can be obtained using more injecting nozzles. Numerical
results are in good agreement with analytical results.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: In the article the remains of the base of the minaret,
found in 2009 at the medieval fortress shakhristan Aktobe, which is
located along the courses of the rivers Balta and Aksu. The minaret,
which consists of two parts: the stylobate in the pit and base part
refers to the XI-XII centuries. The preserved height of the building is
3.6 meters. Volume stylobat quadrangular minaret, the corners of
which are aimed at the four corners of the world amounts to 8,65 x8,
5 m, height – 2.6 m. Diameter octagonal upper cap of 7.85 m and a
height of preserved – 1 m. This minaret is of particular importance
among the historical and architectural monuments of Kazakhstan, as
it is so far the only minaret belonging to Karakhanid epoch in which
Islam was the state religion.
Abstract: Tubular linear induction motor (TLIM) can be used as a capsule pump in a large pneumatic capsule pipeline (PCP) system. Parametric performance evaluation of the designed 1-meter diameter PCP-TLIM system yields encouraging results for practical implementation. The capsule thrust and speed inside the TLIM pump can be calculated from the combination of the PCP fluid mechanics and the TLIM equations. The TLIM equivalent circuits derived from those of the conventional three-phase induction motor are used as a model to predict the static test results of a small-scale PCP-TLIM system. In this paper, additional dynamic tests are performed on the same small-scale PCP-TLIM system with two capsules of different diameters. The behaviors of the capsule inside the pump are observed and analyzed. The dynamic performances from the dynamic tests are compared with the theoretical predictions based on the TLIM equivalent circuit model.
Abstract: Heat transfer from two cam shape cylinder in tandem
arrangement had been studied numerically.
The distance between the centers of cylinders (L) is allowed to
vary to change the longitudinal pitch ratio (L/Deq). The equivalent
diameter of the cylinder (Deq) is 27.6 mm and longitudinal pitch ratio
varies in range 2
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: Silver nanoparticles were prepared by chemical reduction method. Silver nitrate was taken as the metal precursor and hydrazine hydrate as a reducing agent. The formation of the silver nanoparticles was monitored using UV-Vis absorption spectroscopy. The UV-Vis spectroscopy revealed the formation of silver nanopart├¡cles by exhibing the typical surface plasmon absorption maxima at 418-420 nm from the UV–Vis spectrum. Comparison of theoretical (Mie light scattering theory) and experimental results showed that diameter of silver nanoparticles in colloidal solution is about 60 nm. We have used energy-dispersive spectroscopy (EDX), X-ray diffraction (XRD), transmission electron microscopy (TEM) and, UV–Vis spectroscopy to characterize the nanoparticles obtained. The energy-dispersive spectroscopy (EDX) of the nanoparticles dispersion confirmed the presence of elemental silver signal no peaks of other impurity were detected. The average size and morphology of silver nanoparticles were determined by transmission electron microscopy (TEM). TEM photographs indicate that the nanopowders consist of well dispersed agglomerates of grains with a narrow size distribution (40 and 60 nm), whereas the radius of the individual particles are between 10 and 20 nm. The synthesized nanoparticles have been structurally characterized by X-ray diffraction and transmission high-energy electron diffraction (HEED). The peaks in the XRD pattern are in good agreement with the standard values of the face-centered-cubic form of metallic silver (ICCD-JCPDS card no. 4-0787) and no peaks of other impurity crystalline phases were detected. Additionally, the antibacterial activity of the nanopart├¡culas dispersion was measured by Kirby-Bauer method. The nanoparticles of silver showed high antimicrobial and bactericidal activity against gram positive bacteria such as Escherichia Coli, Pseudimonas aureginosa and staphylococcus aureus which is a highly methicillin resistant strain.
Abstract: In order to survive in a rapidly changing business environment, Malaysian business firms must improve their own business practices and procedures. This paper describes the impact of Critical Success Factors (CSFs) during the Enterprise Resource Planning (ERP) system implementations using the responses from 151 organizations that completed or are in the process of completing an ERP implementation and identifying the key benefits of ERP implementation in the firm. The importance of these factors was investigated within Malaysian companies using questionnaire survey method. Our results provide advice to management on how best to utilize their limited resources to choose those CSFs that are most likely to have an impact upon the implementation of the ERP system.
Abstract: In this paper we present the modeling, design, and
experimental testing of a nerve cuff multi-electrode system for
diameter-selective vagus nerve stimulation.
The multi-electrode system contained ninety-nine platinum
electrodes embedded within a self-curling spiral silicone sheet. The
electrodes were organized in a matrix having nine parallel groups,
each containing eleven electrodes.
Preliminary testing of the nerve cuff was performed in an isolated
segment of a swinish left cervical vagus nerve. For selective vagus
nerve stimulation, precisely defined current quasitrapezoidal,
asymmetric and biphasic stimulating pulses were applied to
preselected locations along the left vagus segment via appointed
group of three electrodes within the cuff. Selective stimulation was
obtained by anodal block. However, these pulses may not be safe for
a long-term application because of a frequently used high imbalance
between the cathodic and anodic part of the stimulating pulse.
Preliminary results show that the cuff was capable of exciting A
and B-fibres, and, that for a certain range of parameters used in
stimulating pulses, the contribution of A-fibres to the CAP was
slightly reduced and the contribution of B-fibres was slightly larger.
Results also showed that measured CAPs are not greatly
influenced by the imbalance between a charge Qc injected in cathodic
and Qa in anodic phase of quasitrapezoidal, asymmetric and biphasic
pulses.
Abstract: The expression of LFA-1 diverges from the
physiological condition, thus active targeting carrier can provide the
benefits from difference into LFA-1 expression in various conditions.
Here, the selectivity of cIBR-conjugated nanoparticles (cIBR-NPs),
in terms of uptake, was investigated using PBMCs, Mixed PBMCMolt-
3 cells and Molt-3 cells. The expressions of LFA-1 on Molt-3
cells, from flow cytometry and Western blot, possessed the highest
level whereas PBMCs showed the lowest level. The kinetic uptake
profiles of cIBR-NPs were obtained by flow cytometry, which the
degree of cellular uptake presented a similar trend with the level of
LFA-1 indicating the influence of LFA-1 expression on the cellular
uptake of cIBR-NPs. The conformation of LFA-1 had a slight effect
on the cellular uptake of cIBR-NPs. Overall we demonstrated that
cIBR-NPs enhanced cellular uptake and improved the selectivity of
drug carriers to LFA-1 on the leukemia cells, which related with the
order of LFA-1 expression.
Abstract: This paper deals with analysis of flexural stiffness,
indentation and their energies in three point loading of sandwich
beams with composite faces from Eglass/epoxy and cores from
Polyurethane or PVC. Energy is consumed in three stages of
indentation in laminated beam, indentation of sandwich beam and
bending of sandwich beam. Theory of elasticity is chosen to present
equations for indentation of laminated beam, then these equations
have been corrected to offer better results. An analytical model has
been used assuming an elastic-perfectly plastic compressive behavior
of the foam core. Classical theory of beam is used to describe three
point bending. Finite element (FE) analysis of static indentation
sandwich beams is performed using the FE code ABAQUS. The
foam core is modeled using the crushable foam material model and
response of the foam core is experimentally characterized in uniaxial
compression.
Three point bending and indentation have been done
experimentally in two cases of low velocity and higher velocity
(quasi-impact) of loading. Results can describe response of beam in
terms of core and faces thicknesses, core material, indentor diameter,
energy absorbed, and length of plastic area in the testing. The
experimental results are in good agreement with the analytical and
FE analyses. These results can be used as an introduction for impact
loading and energy absorbing of sandwich structures.
Abstract: Gas hydrates form when a number of factors co-exist:
free water, hydrocarbon gas, cold temperatures and high pressures are typical of the near mud-line conditions in a deepwater drilling
operation. Subsequently, when drilling with water based muds, particularly on exploration wells, the risk of hydrate formation
associated with a gas influx is high. The consequences of gas hydrate
formation while drilling are severe, and as such, every effort should be made to ensure the risk of hydrate formation is either eliminated
or significantly reduced. Thermodynamic inhibitors are used to reduce the free water content of a drilling mud, and thus suppress the
hydrate formation temperature. Very little experimental work has
been performed by oil and gas research companies on the evaluation
of gas hydrate formation in a water-based drilling mud. The main
objective of this paper is to investigate the experimental gas hydrate
formation for a mixture of methane, carbon dioxide & nitrogen in a
water-based drilling mud with or without presence of different
concentrations of thermodynamic inhibitors including pure salt and a
combination of salt with methanol or ethylene glycol at different
concentrations in a static loop apparatus. The experiments were
performed using a static loop apparatus consisting of a 2.4307 cm
inside diameter and 800 cm long pipe. All experiments were conducted at 2200 psia. The temperature in the loop was decreased at
a rate of 3.33 °F/h from initial temperature of 80 °F.
Abstract: In an effort to understand the preliminary effects of aerodynamic stress on alveolar epithelial cells, we developed a multifluidic cell culture platform capable of supporting alveolar cultures at an air-liquid interface under constant air flow and exposure to varying pressure stimuli on the apical side while providing nourishment on the basolateral plane. Our current study involved utilizing the platform to study the effect of basement membrane coating and addition of dexamethasone on cellular response to pressure in A549 and H441 alveolar epithelial cells.
Abstract: Competitive relationships among Bradyrhizobium
japonicum USDA serogroup 123, 122 and 138 were screened versus
the standard commercial soybean variety Williams and two
introductions P1 377578 "671" in a field trial. Displacement of strain
123 by an effective strain should improved N2 fixation. Root nodules
were collected and strain occupancy percentage was determined
using strain specific fluorescent antibodies technique. As anticipated
the strain USDA 123 dominated 92% of nodules due to the high
affinity between the host and the symbiont. This dominance was
consistent and not changed materially either by inoculation practice
or by introducing new strainan. The interrelationship between the
genotype Williams and serogroup 122 & 138 was found very weak
although the cell density of the strain in the rhizosphere area was
equal. On the other hand, the nodule occupancy of genotypes 671 and
166 with rhizobia serogroup 123 was almost diminished to zero. .
The data further exhibited that the genotypes P1 671 and P1 166 have
high affinity to colonize with strains 122 and 138 whereas Williams
was highly promiscuous to strain 123.
Abstract: Square pipes (pipes with square cross sections) are
being used for various industrial objectives, such as machine
structure components and housing/building elements. The utilization
of them is extending rapidly and widely. Hence, the out-put of those
pipes is increasing and new application fields are continually
developing.
Due to various demands in recent time, the products have to
satisfy difficult specifications with high accuracy in dimensions. The
reshaping process design of pipes with square cross sections;
however, is performed by trial and error and based on expert-s
experience.
In this paper, a computer-aided simulation is developed based on
the 2-D elastic-plastic method with consideration of the shear
deformation to analyze the reshaping process. Effect of various
parameters such as diameter of the circular pipe and mechanical
properties of metal on product dimension and quality can be
evaluated by using this simulation. Moreover, design of reshaping
process include determination of shrinkage of cross section,
necessary number of stands, radius of rolls and height of pipe at each
stand, are investigated. Further, it is shown that there are good
agreements between the results of the design method and the
experimental results.