Abstract: Effect of sprue/metal head height on mould filling,
microstructure and mechanical properties of TWDI casting is studied.
Results show that metal/sprue height of 50 mm is not sufficient to
push the melt through the gating channel, but as it is increased from
100-350 mm, proper mould filling is achieved. However at higher
heights between 200 mm and 350 mm, defects associated with
incomplete solidification, carbide precipitation and turbulent flow are
evident. This research shows that superior UTS, hardness, nodularity
and nodule count are obtained at 100 mm sprue height.
Abstract: This paper presents results of compressive strength,
capillary water absorption, and density tests conducted on concrete
containing recycled aggregate (RCA) which is obtained from
structural waste generated by the construction industry in Turkey. In
the experiments, 0%, 15%, 30%, 45% and 60% of the normal
(natural) coarse aggregate was replaced by the recycled aggregate.
Maximum aggregate particle sizes were selected as 16 mm, 22,4 mm
and 31,5 mm; and 0,06%, 0,13% and 0,20% of air-entraining agent
(AEA) were used in mixtures. Fly ash and superplasticizer were used
as a mineral and chemical admixture, respectively. The same type
(CEM I 42.5) and constant dosage of cement were used in the study.
Water/cement ratio was kept constant as 0.53 for all mixture. It was
concluded that capillary water absorption, compressive strength, and
density of concrete decreased with increasing RCA ratio. Increasing
in maximum aggregate particle size and amount of AEA also affect
the properties of concrete significantly.
Abstract: An Acoustic Micro-Energy Harvester (AMEH) is
developed to convert wasted acoustical energy into useful electrical
energy. AMEH is mathematically modeled using Lumped Element
Modelling (LEM) and Euler-Bernoulli beam (EBB) modelling. An
experiment is designed to validate the mathematical model and assess
the feasibility of AMEH. Comparison of theoretical and experimental
data on critical parameter value such as Mm, Cms, dm and Ceb showed
the variances are within 1% to 6%, which is reasonably acceptable.
Then, AMEH undergoes bandwidth tuning for performance
optimization. The AMEH successfully produces 0.9V/(m/s^2) and
1.79μW/(m^2/s^4) at 60Hz and 400kΩ resistive load which only
show variances about 7% compared to theoretical data. At 1g and
60Hz resonance frequency, the averaged power output is about
2.2mW which fulfilled a range of wireless sensors and
communication peripherals power requirements. Finally, the design
for AMEH is assessed, validated and deemed as a feasible design.
Abstract: This study investigates the effects of the lead angle
and chip thickness variation on surface roughness during the
machining of compacted graphite iron using ceramic cutting tools
under dry cutting conditions. Analytical models were developed for
predicting the surface roughness values of the specimens after the
face milling process. Experimental data was collected and imported
to the artificial neural network model. A multilayer perceptron model
was used with the back propagation algorithm employing the input
parameters of lead angle, cutting speed and feed rate in connection
with chip thickness. Furthermore, analysis of variance was employed
to determine the effects of the cutting parameters on surface
roughness. Artificial neural network and regression analysis were
used to predict surface roughness. The values thus predicted were
compared with the collected experimental data, and the
corresponding percentage error was computed. Analysis results
revealed that the lead angle is the dominant factor affecting surface
roughness. Experimental results indicated an improvement in the
surface roughness value with decreasing lead angle value from 88° to
45°.
Abstract: Based on Business and Consumer Survey (BCS) data,
the European Commission (EC) regularly publishes the monthly
Economic Sentiment Indicator (ESI) for each EU member state. ESI
is conceptualized as a leading indicator, aimed ad tracking the overall
economic activity. In calculating ESI, the EC employs arbitrarily
chosen weights on 15 BCS response balances. This paper raises the
predictive quality of ESI by applying nonlinear programming to find
such weights that maximize the correlation coefficient of ESI and
year-on-year GDP growth. The obtained results show that the highest
weights are assigned to the response balances of industrial sector
questions, followed by questions from the retail trade sector. This
comes as no surprise since the existing literature shows that the
industrial production is a plausible proxy for the overall Croatian
economic activity and since Croatian GDP is largely influenced by
the aggregate personal consumption.
Abstract: Food poisoning and infection by bacteria are of public
health significance to both developing and developed countries.
Samples of ogi (akamu) prepared from white and yellow variety of
maize sold in Uturu and Okigwe were analyzed together with the
laboratory prepared ogi for bacterial quality using the standard
microbiological methods. The analyses showed that both white and
yellow variety had total bacterial counts (cfu/g) of 4.0 ×107 and 3.9 x
107 for the laboratory prepared ogi while the commercial ogi had 5.2
x 107 and 4.9 x107, 4.9 x107 and 4.5 x107, 5.4 x107 and 5.0 x107 for
Eke-Okigwe, Up-gate and Nkwo-Achara market respectively. The
Staphylococcal counts ranged from 2.0 x 102 to 5.0 x102 and 1.0 x
102 to 4.0 x102 for the white and yellow variety from the different
markets while Staphylococcal growth was not recorded on the
laboratory prepared ogi. The laboratory prepared ogi had no Coliform
growth while the commercially prepared ogi had counts of 0.5 x103
to 1.6 x 103 for white variety and 0.3 x 103 to 1.1 x103 for yellow
variety respectively. The Lactic acid bacterial count of 3.5x106 and
3.0x106 was recorded for the laboratory ogi while the commercially
prepared ogi ranged from 3.2x106 to 4.2x106 (white variety) and 3.0
x106 to 3.9 x106 (yellow). The presence of bacteria isolates from the
commercial and laboratory fermented ogi showed that Lactobacillus
sp, Leuconostoc sp and Citrobacter sp were present in all the
samples, Micrococcus sp and Klebsiella sp were isolated from Eke-
Okigwe and ABSU-up-gate markets varieties respectively, E. coli
and Staphylococcus sp were present in Eke-Okigwe and Nkwo-
Achara markets while Salmonella sp were isolated from the three
markets. Hence, there are chances of contracting food borne diseases
from commercially prepared ogi. Therefore, there is the need for
sanitary measures in the production of fermented cereals so as to
minimize the rate of food borne pathogens during processing and
storage.
Abstract: Waste Load Allocation (WLA) strategies usually
intend to find economic policies for water resource management.
Water quality trading (WQT) is an approach that uses discharge
permit market to reduce total environmental protection costs. This
primarily requires assigning discharge limits known as total
maximum daily loads (TMDLs). These are determined by monitoring
organizations with respect to the receiving water quality and
remediation capabilities. The purpose of this study is to compare two
approaches of TMDL assignment for WQT policy in small catchment
area of Haraz River, in north of Iran. At first, TMDLs are assigned
uniformly for the whole point sources to keep the concentrations of
BOD and dissolved oxygen (DO) at the standard level at checkpoint
(terminus point). This was simply simulated and controlled by
Qual2kw software. In the second scenario, TMDLs are assigned
using multi objective particle swarm optimization (MOPSO) method
in which the environmental violation at river basin and total treatment
costs are minimized simultaneously. In both scenarios, the equity
index and the WLA based on trading discharge permits (TDP) are
calculated. The comparative results showed that using economically
optimized TMDLs (2nd scenario) has slightly more cost savings rather
than uniform TMDL approach (1st scenario). The former annually
costs about 1 M$ while the latter is 1.15 M$. WQT can decrease
these annual costs to 0.9 and 1.1 M$, respectively. In other word,
these approaches may save 35 and 45% economically in comparison
with command and control policy. It means that using multi objective
decision support systems (DSS) may find more economical WLA,
however its outcome is not necessarily significant in comparison with
uniform TMDLs. This may be due to the similar impact factors of
dischargers in small catchments. Conversely, using uniform TMDLs
for WQT brings more equity that makes stakeholders not feel that
much envious of difference between TMDL and WQT allocation. In
addition, for this case, determination of TMDLs uniformly would be
much easier for monitoring. Consequently, uniform TMDL for TDP
market is recommended as a sustainable approach. However,
economical TMDLs can be used for larger watersheds.
Abstract: This work consists of a numerical simulation of
convective heat transfer in a vertical plane channel filled with a heat
generating porous medium, in the absence of local thermal
equilibrium. The walls are maintained to a constant temperature and
the inlet velocity is uniform. The dynamic range is described by the
Darcy-Brinkman model and the thermal field by two energy
equations model. A dimensionless formulation is developed for
performing a parametric study based on certain dimensionless groups
such as, the Biot interstitial number, the thermal conductivity ratio
and the volumetric heat generation, q '''. The governing equations are
solved using the finite volume method, gave rise to a multitude of
results concerning in particular the thermal field in the porous
channel and the existence or not of the local thermal equilibrium.
Abstract: Due to the resultant leachate from waste
decomposition in landfills has polluter potential hundred times
greater than domestic sewage, this is considered a problem related to
the depreciation of environment requiring pre-disposal treatment.In
seeking to improve this situation, this project proposes the treatment
of landfill leachate using natural fibers intercropped with advanced
oxidation processes. The selected natural fibers were palm, coconut
and banana fiber.These materials give sustainability to the project
because, besides having adsorbent capacity, are often part of waste
discarded. The study was conducted in laboratory scale.In trials, the
effluents were characterized as Chemical Oxygen Demand (COD),
Turbidity and Color. The results indicate that is technically
promising since that there were extremely oxidative conditions, the
use of certain natural fibers in the reduction of pollutants in leachate
have been obtained results of COD removals between 67.9% and
90.9%, Turbidity between 88.0% and 99.7% and Color between
67.4% and 90.4%.The expectation generated is to continue evaluating
the association of efficiency of other natural fibers with other landfill
leachate treatment processes.
Abstract: Psyllium gum alone and in combination with
sunflower oil was investigated as a possible alternative edible coating
for improvement of quality and shelf life of fresh-cut papaya.
Different concentrations including 0.5, 1 and 1.5 percent of psyllium
gum were used for coating of fresh-cut papaya. In some samples,
refined sunflower oil was used as a lipid component to increase the
effectiveness of coating in terms of water barrier properties. Soya
lecithin was used as an emulsifier in coatings containing oil.
Pretreatment with 1% calcium chloride was given to maintain the
firmness of fresh-cut papaya cubes. 1% psyllium gum coating was
found to yield better results. Further, addition of oil helped to
maintain the quality and acted as a barrier to water vapour, therefore,
minimizing the weight loss.
Abstract: The elastic properties and fracture of two-dimensional
graphene were calculated purely from the atomic bonding (stretching
and bending) based on molecular mechanics method. Considering the
representative unit cell of graphene under various loading conditions,
the deformations of carbon bonds and the variations of the interlayer
distance could be realized numerically under the geometry constraints
and minimum energy assumption. In elastic region, it was found that
graphene was in-plane isotropic. Meanwhile, the in-plane deformation
of the representative unit cell is not uniform along armchair direction
due to the discrete and non-uniform distributions of the atoms. The
fracture of graphene could be predicted using fracture criteria based on
the critical bond length, over which the bond would break. It was
noticed that the fracture behavior were directional dependent, which
was consistent with molecular dynamics simulation results.
Abstract: A comparison of activity and stability of the as-formed
Pt/C, Pt-Co and Pt-Pd/C electrocatalysts, prepared by a combined
approach of impregnation and seeding, was performed. According to
the activity test in a single Proton Exchange Membrane (PEM) fuel
cell, the Oxygen Reduction Reaction (ORR) activity of the Pt-M/C
electrocatalyst was slightly lower than that of Pt/C. The j0.9 V and
E10 mA/cm2 of the as-prepared electrocatalysts increased in the order of
Pt/C > Pt-Co/C > Pt-Pd/C. However, in the medium-to-high current
density region, Pt-Pd/C exhibited the best performance. With regard to
their stability in a 0.5 M H2SO4 electrolyte solution, the
electrochemical surface area decreased as the number of rounds of
repetitive potential cycling increased due to the dissolution of the
metals within the catalyst structure. For long-term measurement, Pt-
Pd/C was the most stable than the other three electrocatalysts.
Abstract: This work studies the effect of chemical composition
on the activity and selectivity of γ–alumina supported CuO/
MnO2/Cr2O3 catalysts toward deep oxidation of CO, dimethyl ether
(DME) and methanol. The catalysts were prepared by impregnation
of the support with an aqueous solution of copper nitrate, manganese
nitrate and CrO3 under different conditions. Thermal, XRD and TPR
analysis were performed. The catalytic measurements of single
compounds oxidation were carried out on continuous flow equipment
with a four-channel isothermal stainless steel reactor. Flow-line
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions that mimic closely the industrial
ones was used. The reactant and product gases were analyzed by
means of on-line gas chromatographs.
On the basis of XRD analysis it can be concluded that the active
component of the mixed Cu-Mn-Cr/γ–alumina catalysts consists of at
least six compounds – CuO, Cr2O3, MnO2, Cu1.5Mn1.5O4,
Cu1.5Cr1.5O4 and CuCr2O4, depending on the Cu/Mn/Cr molar ratio.
Chemical composition strongly influences catalytic properties, this
influence being quite variable with regards to the different processes.
The rate of CO oxidation rapidly decrease with increasing of
chromium content in the active component while for the DME was
observed the reverse trend. It was concluded that the best
compromise are the catalysts with Cu/(Mn + Cr) molar ratio 1:5 and
Mn/Cr molar ratio from 1:3 to 1:4.
Abstract: This paper aims to study the effect of cold work
condition on the microstructure of Cu-1.5wt%Ti, and Cu-3.5wt%Ti
and hence mechanical properties. The samples under investigation
were machined, and solution heat treated. X-ray diffraction technique
is used to identify the different phases present after cold deformation
by compression and also different heat treatment and also measuring
the relative quantities of phases present. The metallographic
examination is used to study the microstructure of the samples. The
hardness measurements were used to indicate the change in
mechanical properties. The results are compared with the mechanical
properties obtained by previous workers. Experiments on cold
compression followed by aging of Cu-Ti alloys have indicated that
the most efficient hardening of the material results from continuous
precipitation of very fine particles within the matrix. These particles
were reported to be β`-type, Cu4Ti phase. The β`-β transformation
and particles coarsening within the matrix as well as long grain
boundaries were responsible for the overaging of Cu-1.5wt%Ti and
Cu-3.5wt%Ti alloys. It is well known that plate-like particles are β –
type, Cu3Ti phase. Discontinuous precipitation was found to start at
the grain boundaries and expand into grain interior. At the higher
aging temperature, a classic Widmanstätten morphology forms giving
rise to a coarse microstructure comprised of α and the equilibrium
phase β. Those results were confirmed by X-ray analysis, which
found that a few percent of Cu3Ti, β precipitates are formed during
aging at high temperature for long time for both Cu- Ti alloys (i.e.
Cu-1.5wt%Ti and Cu-3.5wt%Ti).
Abstract: Evidence shows that start-ups success is positively
correlated with the launch of the first product. However, new ventures
are seldom able to acquire abundant resources for new product
development (NPD), which means that entrepreneurs may depend on
personal creativity instead of physical investments to achieve and
accelerate innovation speed. This study accentuates the role of
entrepreneurial bricolage, which defined as making do by applying
combinations of the resources at hand to new problems and
opportunities, in the relations of creative self-efficacy and innovation
speed. This study uses the multiple regression analysis to test the
hypotheses in a sample of 203 start-ups operating in various creative
markets in Taiwan. Results reveal that creative self-efficacy is
positively and directly associated with innovation speed, whereas
entrepreneurial bricolage plays a full mediator. These findings offer
important theoretical and practical implications.
Abstract: Amoxicillin is an antibiotic which is widely used to
treat various infections in both human beings and animals. However,
when amoxicillin is released into the environment, it is a major
problem. Amoxicillin causes bacterial resistance to these drugs and
failure of treatment with antibiotics. Liquid membrane is of great
interest as a promising method for the separation and recovery of the
target ions from aqueous solutions due to the use of carriers for the
transport mechanism, resulting in highly selectivity and rapid
transportation of the desired metal ions. The simultaneous processes
of extraction and stripping in a single unit operation of liquid
membrane system are very interesting. Therefore, it is practical to
apply liquid membrane, particularly the HFSLM for industrial
applications as HFSLM is proved to be a separation process with
lower capital and operating costs, low energy and extractant with
long life time, high selectivity and high fluxes compared with solid
membranes. It is a simple design amenable to scaling up for industrial
applications. The extraction and recovery for (Amoxicillin) through
the hollow fiber supported liquid membrane (HFSLM) using
aliquat336 as a carrier were explored with the experimental data. The
important variables affecting on transport of amoxicillin viz.
extractant concentration and operating time were investigated. The
highest AMOX- extraction percentages of 85.35 and Amoxicillin
stripping of 80.04 were achieved with the best condition at 6 mmol/L
[aliquat336] and operating time 100 min. The extraction reaction
order (n) and the extraction reaction rate constant (kf) were found to
be 1.00 and 0.0344 min-1, respectively.
Abstract: In this work new macroporous Ni electrodes modified
with Au nanoparticles for hydrogen production have been developed.
The supporting macroporous Ni electrodes have been obtained by
means of the electrodeposition at high current densities. Then, the Au
nanoparticles were synthesized and added to the electrode surface.
The electrocatalytic behaviour of the developed electrocatalysts was
studied by means of pseudo-steady-state polarization curves,
electrochemical impedance spectroscopy (EIS) and hydrogen
discharge curves. The size of the Au synthetized nanoparticles shows
a monomodal distribution, with a very sharp band between 10 and 50
nm. The characteristic parameters d10, d50 and d90 were 14, 20 and
31 nm respectively. From Tafel polarization data has been concluded
that the Au nanoparticles improve the catalytic activity of the
developed electrodes towards the HER respect to the macroporous Ni
electrodes. EIS permits to obtain the electrochemically active area by
means of the roughness factor value. All the developed electrodes
show roughness factor values in the same order of magnitude. From
the activation energy results it can be concluded that the Au
nanoparticles improve the intrinsic catalytic activity of the
macroporous Ni electrodes.
Abstract: In this paper, the energy saving and human thermal
comfort in a typical office room are investigated. The impact of a
combined system of exhaust inlet air with light slots located at the
ceiling level in a room served by displacement ventilation system is
numerically modelled. Previous experimental data are used to
validate the Computational Fluid Dynamic (CFD) model. A case
study of simulated office room includes two seating occupants, two
computers, two data loggers and four lamps. The combined system is
located at the ceiling level above the heat sources. A new method of
calculation for the cooling coil load in Stratified Air Distribution
(STRAD) system is used in this study. The results show that 47.4%
energy saving of space cooling load can be achieved by combing the
exhaust inlet air with light slots at the ceiling level above the heat
sources.
Abstract: In this paper, the cable model of dendrites have been
considered. The dendrites are cylindrical cables of various segments
having variable length and reducing radius from start point at synapse
and end points. For a particular event signal being received by a
neuron in response only some dendrite are active at a particular
instance. Initial current signals with different current flows in
dendrite are assumed. Due to overlapping and coupling of active
dendrite, they induce currents in the dendrite segments of each other
at a particular instance. But how these currents are induced in the
various segments of active dendrites due to coupling between these
dendrites, It is not presented in the literature. Here the paper presents
a model for induced currents in active dendrite segments due to
mutual coupling at the starting instance of an activity in dendrite. The
model is as discussed further.
Abstract: This paper presents a rheological model for producing
shape-memory thermoplastic polymers. Shape-memory occurs as a
result of internal rearrangement of the structural elements of a
polymer. A non-linear viscoelastic model was developed that allows
qualitative and quantitative prediction of the stress-strain behavior of
shape-memory polymers during heating. This research was done to
develop a technique to determine the maximum possible change in
size of shape-memory products during heating. The rheological
model used in this work was particularly suitable for defining process
parameters and constructive parameters of the processing equipment.