Abstract: The use of solar energy as a source for pumping water
is one of the promising areas in the photovoltaic (PV) application.
The energy of photovoltaic pumping systems (PVPS) can be widely
improved by employing an MPPT algorithm. This will lead
consequently to maximize the electrical motor speed of the system.
This paper presents a modified incremental conductance (IncCond)
MPPT algorithm with direct control method applied to a standalone
PV pumping system. The influence of the algorithm parameters on
system behavior is investigated and compared with the traditional
(INC) method. The studied system consists of a PV panel, a DC-DC
boost converter, and a PMDC motor-pump. The simulation of the
system by MATLAB-SIMULINK is carried out. Simulation results
found are satisfactory.
Abstract: In this study, static and dynamic responses of a typical
reinforced concrete solid slab, designed to British Standard (BS 8110:
1997) and under self and live loadings for dance halls are reported.
Linear perturbation analysis using finite element method was
employed for modal, impulse loading and frequency response
analyses of the slab under the aforementioned loading condition.
Results from the static and dynamic analyses, comprising of the slab
fundamental frequencies and mode shapes, dynamic amplification
factor, maximum deflection, stress distributions among other
valuable outcomes are presented and discussed. These were gauged
with the limiting provisions in the design code with a view of
justifying valid optimization objective function for the structure that
can ensure both adequate strength and economical section for large
clear span slabs. This is necessary owing to the continued increase in
cost of erecting building structures and the squeeze on public finance
globally.
Abstract: The education sector is constantly faced with rapid
changes in technologies in terms of ensuring that the curriculum is up
to date and in terms of making sure that students are aware of these
technological changes. This challenge can be seen as the motivation
for this study, which is to examine the factors affecting computing
students’ awareness of the latest Information Technologies (ICTs).
The aim of this study is divided into two sub-objectives which are:
the selection of relevant theories and the design of a conceptual
model to support it as well as the empirical testing of the designed
model. The first objective is achieved by a review of existing
literature on technology adoption theories and models. The second
objective is achieved using a survey of computing students in the four
universities of the KwaZulu-Natal province of South Africa. Data
collected from this survey is analyzed using Statistical package for
the Social Science (SPSS) using descriptive statistics, ANOVA and
Pearson correlations. The main hypothesis of this study is that there is
a relationship between the demographics and the prior conditions of
the computing students and their awareness of general ICT trends and
of Digital Switch Over (DSO) a new technology which involves the
change from analog to digital television broadcasting in order to
achieve improved spectrum efficiency. The prior conditions of the
computing students that were considered in this study are students’
perceived exposure to career guidance and students’ perceived
curriculum currency. The results of this study confirm that gender,
ethnicity, and high school computing course affect students’
perceived curriculum currency while high school location affects
students’ awareness of DSO. The results of this study also confirm
that there is a relationship between students prior conditions and their
awareness of general ICT trends and DSO in particular.
Abstract: Radio Frequency Identification (RFID) has become a
key technology in the emerging concept of Internet of Things (IoT).
Naturally, business applications would require the deployment of
various RFID systems developed by different vendors that use
different data formats and structures. This heterogeneity poses a
challenge in developing real-life IoT systems with RFID, as
integration is becoming very complex and challenging. Semantic
integration is a key approach to deal with this challenge. To do so,
ontology for RFID systems need to be developed in order to
annotated semantically RFID systems, and hence, facilitate their
integration. Accordingly, in this paper, we propose ontology for
RFID systems. The proposed ontology can be used to semantically
enrich RFID systems, and hence, improve their usage and reasoning.
Abstract: The purpose of this paper is to contribute to the
enhancement of a hydroelectric plant protection by coordinating
protection measures / existing security and introducing new measures
under a risk management process. In addition, plan identifies key
critical elements of a hydroelectric plant, from its level vulnerabilities
and threats it is subjected to in order to achieve the necessary
protection measures to reduce the level of risk.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.
Abstract: This paper is meant to analyze the ranking of
University of Malaysia Terengganu, UMT’s website in the World
Wide Web. There are only few researches have been done on
comparing the ranking of universities’ websites so this research will
be able to determine whether the existing UMT’s website is serving
its purpose which is to introduce UMT to the world. The ranking is
based on hub and authority values which are accordance to the
structure of the website. These values are computed using two websearching
algorithms, HITS and SALSA. Three other universities’
websites are used as the benchmarks which are UM, Harvard and
Stanford. The result is clearly showing that more work has to be done
on the existing UMT’s website where important pages according to
the benchmarks, do not exist in UMT’s pages. The ranking of UMT’s
website will act as a guideline for the web-developer to develop a
more efficient website.
Abstract: This study presents experimental and optimization of
nanoparticle mass concentration and heat input based on the total
thermal resistance (Rth) of loop heat pipe (LHP), employed for PCCPU
cooling. In this study, silica nanoparticles (SiO2) in water with
particle mass concentration ranged from 0% (pure water) to 1% is
considered as the working fluid within the LHP. The experimental
design and optimization is accomplished by the design of
experimental tool, Response Surface Methodology (RSM). The
results show that the nanoparticle mass concentration and the heat
input have significant effect on the Rth of LHP. For a given heat
input, the Rth is found to decrease with the increase of the
nanoparticle mass concentration up to 0.5% and increased thereafter.
It is also found that the Rth is decreased when the heat input is
increased from 20W to 60W. The results are optimized with the
objective of minimizing the Rth, using Design-Expert software, and
the optimized nanoparticle mass concentration and heat input are
0.48% and 59.97W, respectively, the minimum thermal resistance
being 2.66 (ºC/W).
Abstract: Excessive fretting wear at the taper-trunnion junction
(trunnionosis) apparently contributes to the high failure rates of hip
implants. Implant wear and corrosion lead to the release of metal
particulate debris and subsequent release of metal ions at the tapertrunnion
surface. This results in a type of metal poisoning referred to
as metallosis. The consequences of metal poisoning include;
osteolysis (bone loss), osteoarthritis (pain), aseptic loosening of the
prosthesis and revision surgery. Follow up after revision surgery,
metal debris particles are commonly found in numerous locations. Background: A stable connection between the femoral ball head
(taper) and stem (trunnion) is necessary to prevent relative motions
and corrosion at the taper junction. Hence, the importance of
component assembly cannot be over-emphasized. Therefore, the aim
of this study is to determine the influence of head-stem junction
assembly by press fitting and the subsequent
disengagement/disassembly on the connection strength between the
taper ball head and stem. Methods: CoCr femoral heads were assembled with High stainless
hydrogen steel stem (trunnion) by Push-in i.e. press fit; and
disengaged by pull-out test. The strength and stability of the two
connections were evaluated by measuring the head pull-out forces
according to ISO 7206-10 standards. Findings: The head-stem junction strength linearly increases with
assembly forces.
Abstract: Polycyclic Aromatic Hydrocarbons (PAHs) are
formed mainly because of incomplete combustion of organic
materials during industrial, domestic activities or natural occurrence.
Their toxicity and contamination of terrestrial and aquatic ecosystem
have been established. However, with limited validity index, previous
research has focused on PAHs isomer pair ratios of variable
physicochemical properties in source identification. The objective of
this investigation was to determine the empirical validity of Pearson
Correlation Coefficient (PCC) and Cluster Analysis (CA) in PAHs
source identification along soil samples of different land uses.
Therefore, 16 PAHs grouped, as Endocrine Disruption Substances
(EDSs) were determined in 10 sample stations in top and sub soils
seasonally. PAHs was determined the use of Varian 300 gas
chromatograph interfaced with flame ionization detector. Instruments
and reagents used are of standard and chromatographic grades
respectively. PCC and CA results showed that the classification of
PAHs along pyrolitic and petrogenic organics used in source
signature is about the predominance PAHs in environmental matrix.
Therefore, the distribution of PAHs in the studied stations revealed
the presence of trace quantities of the vast majority of the sixteen
PAHs, which may ultimately inhabit the actual source signature
authentication. Therefore, factors to be considered when evaluating
possible sources of PAHs could be; type and extent of bacterial
metabolism, transformation products/substrates, and environmental
factors such as salinity, pH, oxygen concentration, nutrients, light
intensity, temperature, co-substrates, and environmental medium are
hereby recommended as factors to be considered when evaluating
possible sources of PAHs.
Abstract: Novel wind-lens turbine designs can augment power
output. Vacuum-Assisted Resin Transfer Molding (VARTM) is used
to form large and complex structures from a Carbon Fiber Reinforced
Polymer (CFRP) composite. Typically, wind-lens turbine structures
are fabricated in segments, and then bonded to form the final structure.
This paper introduces five new adhesive joints, divided into two
groups: one is constructed between dry carbon and CFRP fabrics, and
the other is constructed with two dry carbon fibers. All joints and
CFRP fabrics were made in our laboratory using VARTM
manufacturing techniques. Specimens were prepared for tensile testing
to measure joint performance. The results showed that the second
group of joints achieved a higher tensile strength than the first group.
On the other hand, the tensile fracture behavior of the two groups
showed the same pattern of crack originating near the joint ends
followed by crack propagation until fracture.
Abstract: Well logging records can help to answer many
questions from a wide range of special interested information and
basic petrophysical properties to formation evaluation of oil and gas
reservoirs. The accurate calculations of porosity in carbonate
reservoirs are the most challenging aspects of the well logging
analysis. Many equations have been developed over the years based
on known physical principles or on empirically derived relationships,
which are used to calculate porosity, estimate lithology, and water
saturation; however these parameters are calculated from well logs by
using modern technique in a current study. Nasiriya oil field is one of
the giant oilfields in the Middle East, and the formation under study
is the Mishrif carbonate formation which is the shallowest
hydrocarbon bearing zone in this oilfield. Neurolog software was
used to digitize the scanned copies of the available logs.
Environmental corrections had been made as per Schlumberger charts
2005, which supplied in the Interactive Petrophysics software. Three
saturation models have been used to calculate water saturation of
carbonate formations, which are simple Archie equation, Dual water
model, and Indonesia model. Results indicate that the Mishrif
formation consists mainly of limestone, some dolomite, and shale.
The porosity interpretation shows that the logging tools have a good
quality after making the environmental corrections. The average
formation water saturation for Mishrif formation is around 0.4-
0.6.This study is provided accurate behavior of petrophysical
properties with depth for this formation by using modern software.
Abstract: This paper addresses the problem of offline path
planning for Unmanned Aerial Vehicles (UAVs) in complex threedimensional
environment with obstacles, which is modelled by 3D
Cartesian grid system. Path planning for UAVs require the
computational intelligence methods to move aerial vehicles along the
flight path effectively to target while avoiding obstacles. In this paper
Modified Particle Swarm Optimization (MPSO) algorithm is applied
to generate the optimal collision free 3D flight path for UAV. The
simulations results clearly demonstrate effectiveness of the proposed
algorithm in guiding UAV to the final destination by providing
optimal feasible path quickly and effectively.
Abstract: In this study, the three-dimensional cavitating
turbulent flow in a complete Francis turbine is simulated using
mixture model for cavity/liquid two-phase flows. Numerical analysis
is carried out using ANSYS CFX software release 12, and standard k-ε
turbulence model is adopted for this analysis. The computational
fluid domain consist of spiral casing, stay vanes, guide vanes, runner
and draft tube. The computational domain is discretized with a threedimensional
mesh system of unstructured tetrahedron mesh. The
finite volume method (FVM) is used to solve the governing equations
of the mixture model. Results of cavitation on the runner’s blades
under three different boundary conditions are presented and
discussed. From the numerical results it has been found that the
numerical method was successfully applied to simulate the cavitating
two-phase turbulent flow through a Francis turbine, and also
cavitation is clearly predicted in the form of water vapor formation
inside the turbine. By comparison the numerical prediction results
with a real runner; it’s shown that the region of higher volume
fraction obtained by simulation is consistent with the region of runner
cavitation damage.
Abstract: Paper deals with the modeling and simulation of energy consumption and GHG production of two different modes of regional passenger transport – road and railway. These two transport modes use the same type of fuel – diesel. Modeling and simulation of the energy consumption in transport is often used due to calculation satisfactory accuracy and cost efficiency. Paper deals with the calculation based on EN standards and information collected from technical information from vehicle producers and characteristics of tracks. Calculation included maximal theoretical capacity of bus and train and real passenger’s measurement from operation. Final energy consumption and GHG production is calculated by using software simulation. In evaluation of the simulation is used system “well to wheel”.
Abstract: The paper is focused to the evaluation railway tracks
in the Slovakia by using Multi-Criteria method. Evaluation of railway
tracks has important impacts for the assessment of investment in
technical equipment. Evaluation of railway tracks also has an
important impact for the allocation of marshalling yards. Marshalling
yards are in transport model as centers for the operation assigned
catchment area. This model is one of the effective ways to meet the
development strategy of the European Community's railways. By
applying this model in practice, a transport company can guarantee a
higher quality of service and then expect an increase in performance.
The model is also applicable to other rail networks. This model
supplements a theoretical problem of train formation problem of new
ways of looking at evaluation of factors affecting the organization of
wagon flows.
Abstract: Distance learning systems offer useful methods of
learning and usually contain a final course test or another form of
test. The paper proposes a web application for evaluating tests using
an expert system in distance learning systems. The proposed web
application is appropriate for didactic tests or tests with results for
subsequent studying follow-up courses. The web application works
with test questions and uses an expert system and LFLC tool for test
evaluation. After test evaluation, the results are visualized and shown
to the student.
Abstract: The article includes the results and conclusions from
empirical researches that had been done. The research focuses on the
impact of investments made in small and medium-sized enterprises
financed from EU funds on the competitiveness of these companies.
The researches includes financial results in sales revenue and net
income, expenses, and many other new products/services on offer,
higher quality products and services, more modern methods of
production, innovation in management processes, increase in the
number of customers, increase in market share, increase in
profitability of production and provision of services. The main
conclusions are that, companies with direct investments under this
measure shall apply the modern methods of production. The
consequence of this is to increase the quality of our products and
services. Furthermore, both small and medium-sized enterprises have
introduced new products and services. Investments were carried out,
thus enabling better work organization in enterprises. Entrepreneurs
would guarantee higher quality of service, which would result in
better relationships with their customers, what is more, noting the rise
in number of clients. More than half of the companies indicated that
the investments contributed to the increase in market share. Same
thing as for market reach and brand recognition of particular
company. An interesting finding is that, investments in small
enterprises were more effective than medium-sized enterprises.
Abstract: This study aimed to 1) develop pre-service teachers’
leadership skills through camp-based learning, and 2) develop preservice
teachers’ teamwork skills through camp-based learning. An
applied research methodology was used. The target group was
derived from a purposive selection. It involved 32 fourth-year
students in Early Childhood Education Program enrolling a course
entitled Seminar in Early Childhood Education provided during
second semester of academic year 2013. The treatment was camp-based
learning activities which applied a PDCA process including
four stages: 1) plan, 2) do, 3) check, and 4) act. Research instruments
were a learning camp program, a camp-based learning management
plan, a 5-level assessment form for leadership skills and a 5-level
assessment form for assessing teamwork skills. Data were analyzed
using descriptive statistics. Results were: 1) pre-service teachers’
leadership skills yielded the before treatment average score at x= 3.4,
S.D.=0.6 2and the after-treatment average score at x 4.29 , S.D.=0.66
pre-service teachers’ teamwork skills yielded the before-treatment
average score at x=3.31, S.D.=0.60 and the after-treatment average
score at x=4.42, S.D.=0.66 Both differences were statistically
significant at the .05 level. Thus, the pre-service teachers’ leadership
and teamwork skills were significantly improved through the camp-based
learning approach.