Abstract: A conventional binding method for low power in a
high-level synthesis mainly focuses on finding an optimal binding for
an assumed input data, and obtains only one binding table. In this
paper, we show that a binding method which uses multiple binding
tables gets better solution compared with the conventional methods
which use a single binding table, and propose a dynamic bus binding
scheme for low power using multiple binding tables. The proposed
method finds multiple binding tables for the proper partitions of an
input data, and switches binding tables dynamically to produce the
minimum total switching activity. Experimental result shows that the
proposed method obtains a binding solution having 12.6-28.9%
smaller total switching activity compared with the conventional
methods.
Abstract: Blood pulse is an important human physiological signal commonly used for the understanding of the individual physical health. Current methods of non-invasive blood pulse sensing require direct contact or access to the human skin. As such, the performances of these devices tend to vary with time and are subjective to human body fluids (e.g. blood, perspiration and skin-oil) and environmental contaminants (e.g. mud, water, etc). This paper proposes a simulation model for the novel method of non-invasive acquisition of blood pulse using the disturbance created by blood flowing through a localized magnetic field. The simulation model geometry represents a blood vessel, a permanent magnet, a magnetic sensor, surrounding tissues and air in 2-dimensional. In this model, the velocity and pressure fields in the blood stream are described based on Navier-Stroke equations and the walls of the blood vessel are assumed to have no-slip condition. The blood assumes a parabolic profile considering a laminar flow for blood in major artery near the skin. And the inlet velocity follows a sinusoidal equation. This will allow the computational software to compute the interactions between the magnetic vector potential generated by the permanent magnet and the magnetic nanoparticles in the blood. These interactions are simulated based on Maxwell equations at the location where the magnetic sensor is placed. The simulated magnetic field at the sensor location is found to assume similar sinusoidal waveform characteristics as the inlet velocity of the blood. The amplitude of the simulated waveforms at the sensor location are compared with physical measurements on human subjects and found to be highly correlated.
Abstract: An optical fiber Fabry-Perot interferometer (FFPI) is
proposed and demonstrated for dynamic measurements in a
mechanical vibrating target. A polishing metal with a low reflectance
value adhered to a mechanical vibrator was excited via a function
generator at various excitation frequencies. Output interference
fringes were generated by modulating the reference and sensing
signal at the output arm. A fringe-counting technique was used for
interpreting the displacement information on the dedicated computer.
The fiber interferometer has been found the capability of the
displacement measurements of 1.28 μm – 96.01 μm. A commercial
displacement sensor was employed as a reference sensor for
investigating the measurement errors from the fiber sensor. A
maximum percentage measurement error of approximately 1.59 %
was obtained.
Abstract: The design of a modern aircraft is based on three pillars: theoretical results, experimental test and computational simulations.
As a results of this, Computational Fluid Dynamic (CFD) solvers are
widely used in the aeronautical field. These solvers require the correct
selection of many parameters in order to obtain successful results. Besides, the computational time spent in the simulation depends on
the proper choice of these parameters.
In this paper we create an expert system capable of making an
accurate prediction of the number of iterations and time required for the convergence of a computational fluid dynamic (CFD) solver.
Artificial neural network (ANN) has been used to design the expert system. It is shown that the developed expert system is capable of making an accurate prediction the number of iterations and time
required for the convergence of a CFD solver.
Abstract: Software estimation accuracy is among the greatest
challenges for software developers. This study aimed at building and
evaluating a neuro-fuzzy model to estimate software projects
development time. The forty-one modules developed from ten
programs were used as dataset. Our proposed approach is compared
with fuzzy logic and neural network model and Results show that the
value of MMRE (Mean of Magnitude of Relative Error) applying
neuro-fuzzy was substantially lower than MMRE applying fuzzy
logic and neural network.
Abstract: The authors present an algorithm for order reduction of linear dynamic systems using the combined advantages of stability equation method and the error minimization by Genetic algorithm. The denominator of the reduced order model is obtained by the stability equation method and the numerator terms of the lower order transfer function are determined by minimizing the integral square error between the transient responses of original and reduced order models using Genetic algorithm. The reduction procedure is simple and computer oriented. It is shown that the algorithm has several advantages, e.g. the reduced order models retain the steady-state value and stability of the original system. The proposed algorithm has also been extended for the order reduction of linear multivariable systems. Two numerical examples are solved to illustrate the superiority of the algorithm over some existing ones including one example of multivariable system.
Abstract: Analytical solution of the first-order and third-order
shear deformation theories are developed to study the free vibration
behavior of simply supported functionally graded plates. The
material properties of plate are assumed to be graded in the thickness
direction as a power law distribution of volume fraction of the
constituents. The governing equations of functionally graded plates
are established by applying the Hamilton's principle and are solved
by using the Navier solution method. The influence of side-tothickness
ratio and constituent of volume fraction on the natural
frequencies are studied. The results are validated with the known
data in the literature.
Abstract: The paper proposes an approach using genetic algorithm for computing the region based image similarity. The image is denoted using a set of segmented regions reflecting color and texture properties of an image. An image is associated with a family of image features corresponding to the regions. The resemblance of two images is then defined as the overall similarity between two families of image features, and quantified by a similarity measure, which integrates properties of all the regions in the images. A genetic algorithm is applied to decide the most plausible matching. The performance of the proposed method is illustrated using examples from an image database of general-purpose images, and is shown to produce good results.
Abstract: In this paper we compare the response of linear and
nonlinear neural network-based prediction schemes in prediction of
received Signal-to-Interference Power Ratio (SIR) in Direct
Sequence Code Division Multiple Access (DS/CDMA) systems. The
nonlinear predictor is Multilayer Perceptron MLP and the linear
predictor is an Adaptive Linear (Adaline) predictor. We solve the
problem of complexity by using the Minimum Mean Squared Error
(MMSE) principle to select the optimal predictors. The optimized
Adaline predictor is compared to optimized MLP by employing
noisy Rayleigh fading signals with 1.8 GHZ carrier frequency in an
urban environment. The results show that the Adaline predictor can
estimates SIR with the same error as MLP when the user has the
velocity of 5 km/h and 60 km/h but by increasing the velocity up-to
120 km/h the mean squared error of MLP is two times more than
Adaline predictor. This makes the Adaline predictor (with lower
complexity) more suitable than MLP for closed-loop power control
where efficient and accurate identification of the time-varying
inverse dynamics of the multi path fading channel is required.
Abstract: Reconfigurable optical add/drop multiplexers
(ROADMs) can be classified into three categories based on their
underlying switching technologies. Category I consists of a single
large optical switch; category II is composed of a number of small
optical switches aligned in parallel; and category III has a single
optical switch and only one wavelength being added/dropped. In this
paper, to evaluate the wavelength-routing capability of ROADMs of
category-II in dynamic optical networks,the dynamic traffic models
are designed based on Bernoulli, Poisson distributions for smooth
and regular types of traffic. Through Analytical and Simulation
results, the routing power of cat-II of ROADM networks for two
traffic models are determined.
Abstract: In this paper, we proposed a new routing protocol for
Unmanned Aerial Vehicles (UAVs) that equipped with directional
antenna. We named this protocol Directional Optimized Link State
Routing Protocol (DOLSR). This protocol is based on the well
known protocol that is called Optimized Link State Routing Protocol
(OLSR). We focused in our protocol on the multipoint relay (MPR)
concept which is the most important feature of this protocol. We
developed a heuristic that allows DOLSR protocol to minimize
the number of the multipoint relays. With this new protocol the
number of overhead packets will be reduced and the End-to-End
delay of the network will also be minimized. We showed through
simulation that our protocol outperformed Optimized Link State
Routing Protocol, Dynamic Source Routing (DSR) protocol and Ad-
Hoc On demand Distance Vector (AODV) routing protocol in
reducing the End-to-End delay and enhancing the overall
throughput. Our evaluation of the previous protocols was based
on the OPNET network simulation tool.
Abstract: Shortening of natural resources will impose greater
limitations of electric energy consumption in various fields including
water treatment technologies. Small water treatment installations
supplied with electric energy from solar sources are perfect example of
zero-emission technology. Possibility of solar energy application, as
one of the alternative energy resources for decontamination processes
is strongly dependent on geographical location. Various examples of
solar driven water purification systems are given and design of
solar-water treatment installation based on ozone for the geographical
conditions in Poland are presented.
Abstract: Off-grid Photovoltaic (PV) systems are empowering
technology in underdeveloped countries like Ethiopia where many
people live far away from the modern world. Where there is
relatively low energy consumption, providing energy from grid
systems is not commercially cost-effective. As a result, significant
people groups worldwide stay without access to electricity. One
remote village in northern Ethiopia was selected by the United
Nations for a pilot project to improve its living conditions. As part of
this comprehensive project, an intelligent charge controller circuit for
Off-grid PV systems was designed for the clinic in that village. In
this paper, design aspects of an intelligent charge controller unit and
its load driver circuits are discussed for an efficient utilization of PVbased
supply systems.
Abstract: In order to assess optical fiber reliability in different environmental and stress conditions series of testing are performed simulating overlapping of chemical and mechanical controlled varying factors. Each series of testing may be compared using statistical processing: i.e. Weibull plots. Due to the numerous data to treat, a software application has appeared useful to interpret selected series of experiments in function of envisaged factors. The current paper presents a software application used in the storage, modelling and interpretation of experimental data gathered from optical fibre testing. The present paper strictly deals with the software part of the project (regarding the modelling, storage and processing of user supplied data).
Abstract: In this paper a new robust and efficient algorithm to automatic text extraction from colored book and journal cover sheets is proposed. First, we perform wavelet transform. Next for edge detecting from detail wavelet coefficient, we use dynamic threshold. By blurring approximate coefficients with alternative heuristic thresholding, achieve effective edge,. Afterward, with ROI technique get binary image. Finally text boxes would be extracted with new projection profile.
Abstract: This paper describes the process used in the
automation of the Maritime UAV commands using the Kinect sensor.
The AR Drone is a Quadrocopter manufactured by Parrot [1] to be
controlled using the Apple operating systems such as iPhones and
Ipads. However, this project uses the Microsoft Kinect SDK and
Microsoft Visual Studio C# (C sharp) software, which are compatible
with Windows Operating System for the automation of the navigation
and control of the AR drone.
The navigation and control software for the Quadrocopter runs on
a windows 7 computer. The project is divided into two sections; the
Quadrocopter control system and the Kinect sensor control system.
The Kinect sensor is connected to the computer using a USB cable
from which commands can be sent to and from the Kinect sensors.
The AR drone has Wi-Fi capabilities from which it can be connected
to the computer to enable transfer of commands to and from the
Quadrocopter.
The project was implemented in C#, a programming language that
is commonly used in the automation systems. The language was
chosen because there are more libraries already established in C# for
both the AR drone and the Kinect sensor.
The study will contribute toward research in automation of
systems using the Quadrocopter and the Kinect sensor for navigation
involving a human operator in the loop. The prototype created has
numerous applications among which include the inspection of vessels
such as ship, airplanes and areas that are not accessible by human
operators.
Abstract: Contamination of heavy metals in tin tailings has
caused an interest in the scientific approach of their remediation. One
of the approaches is through phytoremediation, which is using tree
species to extract the heavy metals from the contaminated soils. Tin
tailings comprise of slime and sand tailings. This paper reports only
on the finding of the four timber species namely Acacia mangium,
Hopea odorata, Intsia palembanica and Swietenia macrophylla on
the removal of cadmium (Cd) and lead (Pb) from the slime tailings.
The methods employed for sampling and soil analysis are established
methods. Six trees of each species were randomly selected from a
0.25 ha plot for extraction and determination of their heavy metals.
The soil samples were systematically collected according to 5 x 5 m
grid from each plot. Results showed that the concentration of heavy
metals in soils and trees varied according to species. Higher
concentration of heavy metals was found in the stem than the
primary roots of all the species. A. Mangium accumulated the highest
total amount of Pb per hectare basis.
Abstract: In this paper we examine some properties of suborbital graphs for the congruence subgroup r 0 (N) . Then we give necessary and sufficient conditions for graphs to have triangels.
Abstract: This paper presents the simulation results of electric field and potential distributions along surface of silicone rubber polymer insulators under clean and various contamination conditions with/without water droplets. Straight sheds insulator having leakage distance 290 mm was used in this study. Two type of contaminants, playwood dust and cement dust, have been studied the effect of contamination on the insulator surface. The objective of this work is to comparison the effect of contamination on potential and electric field distributions along the insulator surface when water droplets exist on the insulator surface. Finite element method (FEM) is adopted for this work. The simulation results show that contaminations have no effect on potential distribution along the insulator surface while electric field distributions are obviously depended on contamination conditions.
Abstract: The present study aims to explore the role of parents'
ethnic socialization practices contributes to the ethnic identity
development, self-esteem and psychological adjustment of multi
ethnic children in Sabah, Malaysia. A total of 342 multi ethnic
children (age range = 10 years old to 14 years old; mean age = 12.65
years, SD = 0.88) and their parents participated in the present study.
The modified version of Multi group Ethnic Identity Measure
(MEIM), The Familial Ethnic Socialization Measure (FESM). The
Rosenberg Self-Esteem Scale (RSE) and Behavioral and Emotional
Rating Scale Edition 2 (BERS-2) were used in this study. The results
showed that: i) parents' ethnic socialization practice was a strong
predictor of ethnic identity development of multi ethnic children; ii)
parents' ethnic socialization practice also was a significant predictor
of self-esteem of multi ethnic children; iii) parents' ethnic
socialization practice was not a significant predictor of psychological
adjustment of multi ethnic children. The results of this study showed
the implications parents' ethnic socialization practices and ethnic
identity development in successful multi ethnic families.