Abstract: Biodiesel is traditionally produced from oleaginous
plants. On the other hand, increasing biodiesel production from these
raw materials could create problems of food supply. Producing
biodiesel from microalgae could help to overcome this difficulty,
because microalgae are rich in lipids and do not compete for arable
lands. However, no studies had compared vegetable and microalgae
oil-based biodiesel in terms of yield, viscosity and heat of
combustion. In the present study, commercial canola and microalgae
oil were therefore transesterified with methanol under a homogenous
alkali catalyst (potassium hydroxide) at 100oC for 1h. The result
showed that microalgae-based oil has a higher yield in biodiesel with
89.7% (g biodiesel/g oil) and a lower kinematic viscosity (22oC) of
4.31 mm/s2 than canola oil.
Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.
Abstract: Scouring around a bridge pier is a complex
phenomenon. More laboratory experiments are required to
understand the scour mechanism. This paper focused on time
development of local scour around piers and piles in semi integral
bridges. Laboratory data collected at Hydraulics Laboratory,
University of Malaya was analyzed for this purpose. Tests were
performed with two different uniform sediment sizes and five ranges
of flow velocities. Fine and coarse sediments were tested in the
flume. Results showed that scour depths for both pier and piles
increased with time up to certain levels and after that they became
almost constant. It had been found that scour depths increased when
discharges increased. Coarser sediment also produced lesser scouring
at the piers and combined piles.
Abstract: Female breast cancer is the second in frequency after cervical cancer. Surgery is the most common treatment for breast cancer, followed by chemotherapy as a treatment of choice. Although effective, it causes serious side effects. Controlled-release drug delivery is an alternative method to improve the efficacy and safety of the treatment. It can release the dosage of drug between the minimum effect concentration (MEC) and minimum toxic concentration (MTC) within tumor tissue and reduce the damage of normal tissue and the side effect. Because an in vivo experiment of this system can be time-consuming and labor-intensive, a mathematical model is desired to study the effects of important parameters before the experiments are performed. Here, we describe a 3D mathematical model to predict the release of doxorubicin from pluronic gel to treat human breast cancer. This model can, ultimately, be used to effectively design the in vivo experiments.
Abstract: We review a knowledge extractor model in
constructing 3G Killer Applications. The success of 3G is essential
for Government as it became part of Telecommunications National
Strategy. The 3G wireless technologies may reach larger area and
increase country-s ICT penetration. In order to understand future
customers needs, the operators require proper information
(knowledge) lying inside. Our work approached future customers as
complex system where the complex knowledge may expose regular
behavior. The hidden information from 3G future customers is
revealed by using fractal-based questionnaires. Afterward, further
statistical analysis is used to match the results with operator-s
strategic plan. The developments of 3G applications also consider its
saturation time and further improvement of the application.
Abstract: We derive simple sets of equations to describe the microwave response of a thin film of magnetized hydrogen plasma in the presence of carbon nanotubes, which were grown by ironcatalyzed high-pressure disproportionation (HiPco). By considering the interference effects due to multiple reflections between thin plasma film interfaces, we present the effects of the continuously changing external magnetic field and plasma parameters on the reflected power, absorbed power, and transmitted power in the system. The simulation results show that the interference effects play an important role in the reflectance, transmittance and absorptance of microwave radiation at the magnetized plasma slab. As a consequence, the interference effects lead to a sinusoidal variation of the reflected intensity and can greatly reduce the amount of reflection power, but the absorption power increases.
Abstract: Poly (ethylene glycol) (PEG) molecules attached to surfaces have shown high potential as a protein repellent due to their flexibility and highly water solubility. A quartz crystal microbalance recording frequency and dissipation changes (QCM-D) has been used to study the adsorption from aqueous solutions, of lysozyme and α-lactalbumin proteins (the last with and without calcium) onto modified stainless steel surfaces. Surfaces were coated with poly(ethylene imine) (PEI) and silicate before grafting on PEG molecules. Protein adsorption was also performed on the bare stainless steel surface as a control. All adsorptions were conducted at 23°C and pH 7.2. The results showed that the presence of PEG molecules significantly reduced the adsorption of lysozyme and α- lactalbumin (with calcium) onto the stainless steel surface. By contrast, and unexpected, PEG molecules enhanced the adsorption of α-lactalbumin (without calcium). It is suggested that the PEG -α- lactalbumin hydrophobic interaction plays a dominant role which leads to protein aggregation at the surface for this latter observation. The findings also lead to the general conclusion that PEG molecules are not a universal protein repellent. PEG-on-PEI surfaces were better at inhibiting the adsorption of lysozyme and α-lactalbumin (with calcium) than with PEG-on-silicate surfaces.
Abstract: Uncertainties of a serial production line affect on the
production throughput. The uncertainties cannot be prevented in a
real production line. However the uncertain conditions can be
controlled by a robust prediction model. Thus, a hybrid model
including autoregressive integrated moving average (ARIMA) and
multiple polynomial regression, is proposed to model the nonlinear
relationship of production uncertainties with throughput. The
uncertainties under consideration of this study are demand, breaktime,
scrap, and lead-time. The nonlinear relationship of production
uncertainties with throughput are examined in the form of quadratic
and cubic regression models, where the adjusted R-squared for
quadratic and cubic regressions was 98.3% and 98.2%. We optimized
the multiple quadratic regression (MQR) by considering the time
series trend of the uncertainties using ARIMA model. Finally the
hybrid model of ARIMA and MQR is formulated by better adjusted
R-squared, which is 98.9%.
Abstract: This paper deals with new concept of using compressed atmospheric air as a zero pollution power source for running motorbikes. The motorbike is equipped with an air turbine in place of an internal combustion engine, and transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor to casing diameter ratios with respect to different vane angles (number of vanes) have been considered and analyzed. It is found that the shaft work output is optimum for some typical values of rotor / casing diameter ratios at a particular value of vane angle (no. of vanes). In this study, the maximum power is obtained as 4.5kW - 5.3kW (5.5-6.25 HP) when casing diameter is taken 100 mm, and rotor to casing diameter ratios are kept from 0.65 to 0.55. This value of output is sufficient to run motorbike.
Abstract: Maize and Indian mustard are significant crops in
semi-arid climate zones of India. Improved water management
requires precise scheduling of irrigation, which in turn requires an
accurate computation of daily crop evapotranspiration (ETc). Daily
crop evapotranspiration comes as a product of reference
evapotranspiration (ET0) and the growth stage specific crop
coefficients modified for daily variation. The first objective of
present study is to develop crop coefficients Kc for Maize and Indian
mustard. The estimated values of Kc for maize at the four crop
growth stages (initial, development, mid-season, and late season) are
0.55, 1.08, 1.25, and 0.75, respectively, and for Indian mustard the Kc
values at the four growth stages are 0.3, 0.6, 1.12, and 0.35,
respectively. The second objective of the study is to compute daily
crop evapotranspiration from ET0 and crop coefficients. Average
daily ETc of maize varied from about 2.5 mm/d in the early growing
period to > 6.5 mm/d at mid season. The peak ETc of maize is 8.3
mm/d and it occurred 64 days after sowing at the reproductive growth
stage when leaf area index was 4.54. In the case of Indian mustard,
average ETc is 1 mm/d at the initial stage, >1.8 mm/d at mid season
and achieves a peak value of 2.12 mm/d on 56 days after sowing.
Improved schedules of irrigation have been simulated based on daily
crop evapo-transpiration and field measured data. Simulation shows a
close match between modeled and field moisture status prevalent
during crop season.
Abstract: This is a cross-cultural study that determines South
African multinational enterprises (MNEs) entry strategies as they
invest in Africa. An integrated theoretical framework comprising the
transaction cost theory, Uppsala model, eclectic paradigm and the
distance framework was adopted. A sample of 40 South African
MNEs with 415 existing FDI entries in Africa was drawn. Using an
ordered logistic regression model, the impact of culture on the choice
of degree of control by South African MNEs in Africa was
determined. Cultural distance was one of significant factors that
influenced South African MNEs- choice of degree of control.
Furthermore, South African MNEs are risk averse in all countries in
Africa but minimize the risks differently across sectors. Service
sectors chooses to own their subsidiaries 100% and avoid dealing
with the locals while manufacturing, resources and construction
choose to have a local partner to share the risk.
Abstract: Renewed interest in propeller propulsion on aircraft
configurations combined with higher propeller loads lead to the question how the effects of the propulsion on model support disturbances
should be accounted for. In this paper, the determination of engine power effects on support interference of sting-mounted models is
demonstrated by a measurement on a four-engine turboprop aircraft.
CFD results on a more generic model are presented in order to clarify
the possible mechanism behind engine power effects on support
interference. The engine slipstream induces a local change in angle
of sideslip at the model sting thereby influencing the sting near-field and far-field effects. Whether or not the net result of these changes
in the disturbance pattern leads to a significant engine power effect depends on the configuration of the wind tunnel model and the test
setup.
Abstract: In this paper an approaches for increasing the
effectiveness of error detection in computer network channels with
Pulse-Amplitude Modulation (PAM) has been proposed. Proposed
approaches are based on consideration of special feature of errors,
which are appearances in line with PAM. The first approach consists
of CRC modification specifically for line with PAM. The second
approach is base of weighted checksums using. The way for
checksum components coding has been developed. It has been shown
that proposed checksum modification ensure superior digital data
control transformation reliability for channels with PAM in compare
to CRC.
Abstract: The experiment was then conducted to investigate the
effect of cassava peel addition in the concentrate on the performance
of lactating dairy cows. Twenty four Holstein Friesian crossbred
(>87.5% Holstein Friesian) lactating dairy cows in mid lactation;
averaging 12.2+2.1 kg of milk, 119+45 days in milk, 44.1+6.2
months old and 449+33 kg live weight, were stratified for milk yield,
days in milk, age, stage of lactation and body weight, and then
randomly allocated to three treatment groups. The first, second and
third groups were fed concentrates containing the respective cassava
peel, 0, 20 and 40%. All cows were fed ad libitum corn silage and
freely access to clean water. Dry matter intake, 4%FCM, milk
composition and body weight change were affected (P
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: This paper focuses on robust design and optimization
of industrial production wastes. Past literatures were reviewed to case
study Clamason Industries Limited (CIL) - a leading ladder-tops
manufacturer. A painstaking study of the firm-s practices at the shop
floor revealed that Over-production, Waiting time, Excess inventory,
and Defects are the major wastes that are impeding their progress and
profitability. Design expert8 software was used to apply Taguchi
robust design and response surface methodology in order to model,
analyse and optimise the wastes cost in CIL. Waiting time and overproduction
rank first and second in contributing to the costs of wastes
in CIL. For minimal wastes cost the control factors of overproduction,
waiting-time, defects and excess-inventory must be set at
0.30, 390.70, 4 and 55.70 respectively for CIL. The optimal value of
cost of wastes for the months studied was 22.3679. Finally, a
recommendation was made that for the company to enhance their
profitability and customer satisfaction, they must adopt the Shingeo
Shingo-s Single Minute Exchange of Dies (SMED), which will
immediately tackle the waste of waiting by drastically reducing their
setup time.
Abstract: The forest stand consisted of four layers. The species
composition between the third and the bottom layers was almost
similar, whereas it was almost exclusive between the top and the lower
three layers. The values of Shannon-s index H' and Pielou-s index
J ' tended to increase from the bottom layer upward, except for
H' -value of the top layer. The values of H' and J ' were 4.21 bit
and 0.73, respectively, for the total stand. High woody species
diversity of the forest depended on large trees in the upper layers,
which trend was different from a subtropical evergreen broadleaf
forest grown in silicate habitat in the northern part of Okinawa Island.
The spatial distribution of trees was overlapped between the third and
the bottom layers, whereas it was independent or slightly exclusive
between the top and the lower three layers. Mean tree weight of each
layer decreased from the top toward the bottom layer, whereas the
corresponding tree density increased from the top downward. This
relationship was analogous to the process of self-thinning plant
populations.
Abstract: Dextran is a D-glucose polymer which is produced by
Leuconostoc mesenteroides grown in a sucrose-rich media. The
organism was obtained from the Persian Type Culture Collection
(PTCC) and was transferred in MRS broth medium at 30°C and pH
6.8 for 24 h. After preparation of inoculums, organisms were
inoculated into five liquid fermentation media containing either
molasses or cheese whey or different combinations of cheese whey
and molasses. After certain fermentation period, the produced
dextran was separated and dried. Dextran yield was calculated and
significant differences in different media were observed.
Furthermore, FT-IR analysis was performed and the results showed
that there were no significant differences in the produced dextran
structures.
Abstract: Amarindra-vinitchai-mahaisuraya Bhiman throne hall
is one of the most significant throne halls in the grand palace in the
Ratthanakosin city situated in Bangkok, Thailand. This is the first
group of throne halls built in order to serve as a place for meetings,
performing state affairs and royal duties until the present time. The
structure and pattern of architectural design including the decoration
and interior design of the throne hall obviously exhibits and convey
the status of the king under the context of Thai society in the early
period of Ratthanakosin era. According to the tradition of ruling the
kingdom in absolute monarchy which had been in place since
Ayutthaya era (A.D.1350-1767), the king was deemed as Deva Raja,
the highest power and authority over the kingdom and as the greatest
emperor of the universe (Chakkravatin). The architectural design
adopted the concept of “Prasada" or Viman which served as the
dwelling place of the gods and was presented in the form of “Thai
traditional architecture" For the interior design of the throne hall, it
had been adopted to be the heaven and the centre of the Universe in
line with the cosmological beliefs of ancient people described in
scripture Tribhumikatha (Tri Bhumi) written by Phra Maha Thamma
Raja (Phraya Lithai) of the Sukhothai era (A.D.1347-1368).
According to this belief, the throne hall had been designed to represent
mount Meru, the central of the universe. On the top end of Mount
Meru is situated the Viman and dwelling place of Indra who is the king
of gods according to the idea of Deva Raja (the king god Avatar). At
the same time, Indra also existed as the king of the universe
simultaneously.
Abstract: Antioxidant activities of ethanolic extracts of Ardisia
japonica Blume., Ageartum conyzoides Linn., and Cocculus hirsutus
Linn Diels. leaves was determined qualitatively and quantitatively in
this research. 1, 1-diphenyl-2-picrylhydrazyl (DPPH) free radical
solution was used to investigate free radical scavenging activity of
these leaves extracts. Ascorbic acid (Vitamin C) was used as the
standard. In the present investigation, it is found that all of these
extracts have remarkable antioxidant activities. The EC50 values of
these ethanolic extracts were 12.72 μg/ml for A. japonica, 15.19
μg/ml for A. conyzoides, 10.68 μg/ml for C. hirsutus respectively.
Among these Myanmar medicinal plants, C. hirsutus showed higher
antioxidant activities as well as free radical scavenging activity than
black tea (Camellia sinensis), the famous antioxidant, and A.
japonica and A. conyzoides showed a rather lower antioxidant
activity than tea extracts. According to results from bioassay with
carrot discs infected with Agrobacterium tumefaciens, all extracts
showed anti-tumor activity after 3 weeks of incubation. No gall was
detected in carrot disks treated with C. hirsutus and A. japonica
extracts in the dose of 100ppm and in carrot discs treated with A.
conyzoides extract in the dose of 1000 ppm. Therefore, the research
clearly indicates that these weedy plants of dry farm land are
exceptionally advantageous for human health.