Abstract: Utilization of bagasse ash for silica sources is one of
the most common application for agricultural wastes and valuable
biomass byproducts in sugar milling. The high percentage silica
content from bagasse ash was used as silica source for sodium
silicate solution. Different heating temperature, time and acid
treatment were studies for silica extraction. The silica was
characterized using various techniques including X-ray fluorescence,
X-ray diffraction, Scanning electron microscopy, and Fourier
Transform Infrared Spectroscopy method,. The synthesis conditions
were optimized to obtain the bagasse ash with the maximum silica
content. The silica content of 91.57 percent was achieved from
heating of bagasse ash at 600°C for 3 hours under oxygen feeding
and HCl treatment. The result can be used as value added for bagasse
ash utilization and minimize the environmental impact of disposal
problems.
Abstract: Titanium nitride (TiN) has been synthesized using the
sheet plasma negative ion source (SPNIS). The parameters used for
its effective synthesis has been determined from previous
experiments and studies. In this study, further enhancement of the
deposition rate of TiN synthesis and advancement of the SPNIS
operation is presented. This is primarily achieved by the addition of
Sm-Co permanent magnets and a modification of the configuration in
the TiN deposition process. The magnetic enhancement is aimed at
optimizing the sputtering rate and the sputtering yield of the process.
The Sm-Co permanent magnets are placed below the Ti target for
better sputtering by argon. The Ti target is biased from –250V to –
350V and is sputtered by Ar plasma produced at discharge current of
2.5–4A and discharge potential of 60–90V. Steel substrates of
dimensions 20x20x0.5mm3 were prepared with N2:Ar volumetric
ratios of 1:3, 1:5 and 1:10. Ocular inspection of samples exhibit
bright gold color associated with TiN. XRD characterization
confirmed the effective TiN synthesis as all samples exhibit the (200)
and (311) peaks of TiN and the non-stoichiometric Ti2N (220) facet.
Cross-sectional SEM results showed increase in the TiN deposition
rate of up to 0.35μm/min. This doubles what was previously obtained
[1]. Scanning electron micrograph results give a comparative
morphological picture of the samples. Vickers hardness results gave
the largest hardness value of 21.094GPa.
Abstract: The term interactive education indicates the meaning
related with multidisciplinary aspects of distance education following
contemporary means around a common basis with different
functional requirements. The aim of this paper is to reflect the new
techniques in education with the new methods and inventions. These
methods are better supplied by interactivity. The integration of
interactive facilities in the discipline of education with distance
learning is not a new concept but in addition the usage of these
methods on design issue is newly being adapted to design education.
In this paper the general approach of this method and after the
analysis of different samples, the advantages and disadvantages of
these approaches are being identified. The method of this paper is to
evaluate the related samples and then analyzing the main hypothesis.
The main focus is to mention the formation processes of this
education. Technological developments in education should be
filtered around the necessities of the design education and the
structure of the system could then be formed or renewed. The
conclusion indicates that interactive methods of education in design
issue is a meaning capturing not only technical and computational
intelligence aspects but also aesthetical and artistic approaches
coming together around the same purpose.
Abstract: Low silica type X (LSX) Zeolite is one of useful
material in many manufacturing due to the advantage properties
including high surface area, stability, microporous crystalline
aluminosilicates and positive ion in an extra–framework. The LSX
was used rice husk silica source which obtained by leaching with
hydrochloric acid and calcination at 500 C. To improve the
synthesis method, the LSX was crystallizated in Teflon–lined
autoclave will expedite deceasing of the amorphous particles. The
mixed gel with composition of 5.5 Na2O : 1.65 K2O : Al2O3 : 2.2
SiO2 : 122 H2O was crystallized in different container
(Polypropylene bottom and Teflon–lined autoclave). The obtained
powder was characterized by X–ray diffraction (XRD), X–ray
fluorescence spectrometry, N2 adsorption-desorption analysis BET
surface area Scanning electron microscopy (SEM) and Fourier
transform infrared spectroscopy to justify the quality of zeolite. The
results showed the crystallized zeolite in Teflon lined autoclave has
102.8 nm of crystal size, 286 m2/g of surface area and fewer amounts
of round amorphous particles when compared with the crystallized
zeolite in Polypropylene.
Abstract: Magnetic and semiconductor nanomaterials exhibit
novel magnetic and optical properties owing to their unique size and
shape-dependent effects. With shrinking the size down to nanoscale
region, various anomalous properties that normally not present in bulk
start to dominate. Ability in harnessing of these anomalous properties
for the design of various advance electronic devices is strictly
dependent on synthetic strategies. Hence, current research has focused
on developing a rational synthetic control to produce high quality
nanocrystals by using organometallic approach to tune both size and
shape of the nanomaterials. In order to elucidate the growth
mechanism, transmission electron microscopy was employed as a
powerful tool in performing real time-resolved morphologies and
structural characterization of magnetic (Fe3O4) and semiconductor
(ZnO) nanocrystals. The current synthetic approach is found able to
produce nanostructures with well-defined shapes. We have found that
oleic acid is an effective capping ligand in preparing oxide-based
nanostructures without any agglomerations, even at high temperature.
The oleate-based precursors and capping ligands are fatty acid
compounds, which are respectively originated from natural palm oil
with low toxicity. In comparison with other synthetic approaches in
producing nanostructures, current synthetic method offers an effective
route to produce oxide-based nanomaterials with well-defined shapes
and good monodispersity. The nanocystals are well-separated with
each other without any stacking effect. In addition, the as-synthesized
nanopellets are stable in terms of chemically and physically if
compared to those nanomaterials that are previous reported. Further
development and extension of current synthetic strategy are being
pursued to combine both of these materials into nanocomposite form
that will be used as “smart magnetic nanophotocatalyst" for industry
waste water treatment.
Abstract: In most wheat growing moderate regions and
especially in the north of Iran climate, is affected grain filling by
several physical and abiotic stresses. In this region, grain filling often
occurs when temperatures are increasing and moisture supply is
decreasing. The experiment was designed in RCBD with split plot
arrangements with four replications. Four irrigation treatments
included (I0) no irrigation (check); (I1) one irrigation (50 mm) at
heading stage; (I2) two irrigation (100 mm) at heading and anthesis
stage; and (I3) three irrigation (150 mm) at heading, anthesis and
early grain filling growth stage, two wheat cultivars (Milan and
Shanghai) were cultured in the experiment. Totally raining was 453
mm during the growth season. The result indicated that biological
yield, grain yield and harvest index were significantly affected by
irrigation levels. I3 treatment produced more tillers number in m2,
fertile tillers number in m2, harvest index and biological yield. Milan
produced more tillers number in m2, fertile tillers in m2, while
Shanghai produced heavier tillers and grain 1000 weight. Plant height
was significant in wheat varieties while were not statistically
significant in irrigation levels. Milan produced more grain yield,
harvest index and biological yield. Grain yield shown that I1, I2, and
I3 produced increasing of 5228 (21%), 5460 (27%) and 5670 (29%)
kg ha-1, respectively. There was an interaction of irrigation and
cultivar on grain yields. In the absence of the irrigation reduced grain
1000 weight from 45 to 40 g. No irrigation reduced soil moisture
extraction during the grain filling stage. Current assimilation as a
source of carbon for grain filling depends on the light intercepting
viable green surfaces of the plant after anthesis that due to natural
senescence and the effect of various stresses. At the same time the
demand by the growing grain is increasing. It is concluded from
research work that wheat crop irrigated Milan cultivar could increase
the grain yield in comparison with Shanghai cultivar. Although, the
grain yield of Shanghai under irrigation was slightly lower than
Milan. This grain yield also was related to weather condition, sowing
date, plant density and location conditions and management of
fertilizers, because there was not significant difference in biological
and straw yield. The best result was produced by I1 treatment. I2 and
I3 treatments were not significantly difference with I1 treatment.
Grain yield of I1 indicated that wheat is under soil moisture
deficiency. Therefore, I1 irrigation was better than I0.
Abstract: Sweet potato products are necessary for the provision
of essential nutrients in every household, regardless of their poverty
status. Their consumption appears to be highly influenced by socioeconomic
factors, such as malnutrition, food insecurity and
unemployment. Therefore, market availability is crucial for these
cultivars to resolve some of the socio-economic factors. The aim of
the study was to investigate market availability of sweet potato
cultivars in the North West Province. In this study, both qualitative
and quantitative research methodologies were used. Qualitative
methodology was used to explain the quantitative outcomes of the
variables. On the other hand, quantitative results were used to test the
hypothesis. The study used SPSS software to analyse the data. Crosstabulation
and Chi-square statistics were used to obtain the
descriptive and inferential analyses, respectively. The study found
that the Blesbok cultivar is dominating the markets of the North West
Province, with the Monate cultivar dominating in the Bojanala
Platinum (75%) and Dr Ruth Segomotsi Mompati (25%) districts. It
is also found that a unit increase in the supply of sweet potato
cultivars in both local and district municipal markets is accompanied
by a reduced demand of 28% and 33% at district and local markets,
respectively. All these results were found to be significant at p
Abstract: Heterogeneity has to be taken into account when
integrating a set of existing information sources into a distributed
information system that are nowadays often based on Service-
Oriented Architectures (SOA). This is also particularly applicable to
distributed services such as event monitoring, which are useful in the
context of Event Driven Architectures (EDA) and Complex Event
Processing (CEP). Web services deal with this heterogeneity at a
technical level, also providing little support for event processing. Our
central thesis is that such a fully generic solution cannot provide
complete support for event monitoring; instead, source specific
semantics such as certain event types or support for certain event
monitoring techniques have to be taken into account. Our core result
is the design of a configurable event monitoring (Web) service that
allows us to trade genericity for the exploitation of source specific
characteristics. It thus delivers results for the areas of SOA, Web
services, CEP and EDA.
Abstract: Above Elbow Prosthesis is one of the most commonly
amputated or missing limbs. The research is done for modelling
techniques of upper limb prosthesis and design of high torque, light
weight and compact in size elbow actuator. The purposed actuator
consists of a DC motor, planetary gear set and a harmonic drive. The
calculations show that the actuator is good enough to be used in real
life powered prosthetic upper limb or rehabilitation exoskeleton.
Abstract: A conventional binding method for low power in a
high-level synthesis mainly focuses on finding an optimal binding for
an assumed input data, and obtains only one binding table. In this
paper, we show that a binding method which uses multiple binding
tables gets better solution compared with the conventional methods
which use a single binding table, and propose a dynamic bus binding
scheme for low power using multiple binding tables. The proposed
method finds multiple binding tables for the proper partitions of an
input data, and switches binding tables dynamically to produce the
minimum total switching activity. Experimental result shows that the
proposed method obtains a binding solution having 12.6-28.9%
smaller total switching activity compared with the conventional
methods.
Abstract: Under-representation of women in leadership positions" is still a general phenomenon in Germany despite the high number of implemented measures. The under-representation of female executives in the aviation sector is even worse. In this context our research hypothesis is that the representation and acceptance of women in management positions is determined by corporate culture.
Abstract: The more recent satellite projects/programs makes
extensive usage of real – time embedded systems. 16 bit processors
which meet the Mil-Std-1750 standard architecture have been used in
on-board systems. Most of the Space Applications have been written
in ADA. From a futuristic point of view, 32 bit/ 64 bit processors are
needed in the area of spacecraft computing and therefore an effort is
desirable in the study and survey of 64 bit architectures for space
applications. This will also result in significant technology
development in terms of VLSI and software tools for ADA (as the
legacy code is in ADA).
There are several basic requirements for a special processor for
this purpose. They include Radiation Hardened (RadHard) devices,
very low power dissipation, compatibility with existing operational
systems, scalable architectures for higher computational needs,
reliability, higher memory and I/O bandwidth, predictability, realtime
operating system and manufacturability of such processors.
Further on, these may include selection of FPGA devices, selection
of EDA tool chains, design flow, partitioning of the design, pin
count, performance evaluation, timing analysis etc.
This project deals with a brief study of 32 and 64 bit processors
readily available in the market and designing/ fabricating a 64 bit
RISC processor named RISC MicroProcessor with added
functionalities of an extended double precision floating point unit
and a 32 bit signal processing unit acting as co-processors. In this
paper, we emphasize the ease and importance of using Open Core
(OpenSparc T1 Verilog RTL) and Open “Source" EDA tools such as
Icarus to develop FPGA based prototypes quickly. Commercial tools
such as Xilinx ISE for Synthesis are also used when appropriate.
Abstract: Carbon nanotubes (CNTs) possess unique structural,
mechanical, thermal and electronic properties, and have been
proposed to be used for applications in many fields. However, to
reach the full potential of the CNTs, many problems still need to be
solved, including the development of an easy and effective
purification procedure, since synthesized CNTs contain impurities,
such as amorphous carbon, carbon nanoparticles and metal particles.
Different purification methods yield different CNT characteristics
and may be suitable for the production of different types of CNTs. In
this study, the effect of different purification chemicals on carbon
nanotube quality was investigated. CNTs were firstly synthesized by
chemical vapor deposition (CVD) of acetylene (C2H2) on a
magnesium oxide (MgO) powder impregnated with an iron nitrate
(Fe(NO3)3·9H2O) solution. The synthesis parameters were selected
as: the synthesis temperature of 800°C, the iron content in the
precursor of 5% and the synthesis time of 30 min. The liquid phase
oxidation method was applied for the purification of the synthesized
CNT materials. Three different acid chemicals (HNO3, H2SO4, and
HCl) were used in the removal of the metal catalysts from the
synthesized CNT material to investigate the possible effects of each
acid solution to the purification step. Purification experiments were
carried out at two different temperatures (75 and 120 °C), two
different acid concentrations (3 and 6 M) and for three different time
intervals (6, 8 and 15 h). A 30% H2O2 : 3M HCl (1:1 v%) solution
was also used in the purification step to remove both the metal
catalysts and the amorphous carbon. The purifications using this
solution were performed at the temperature of 75°C for 8 hours.
Purification efficiencies at different conditions were evaluated by
thermogravimetric analysis. Thermal and electrical properties of
CNTs were also determined. It was found that the obtained electrical
conductivity values for the carbon nanotubes were typical for organic
semiconductor materials and thermal stabilities were changed
depending on the purification chemicals.
Abstract: Human middle-ear is the key component of the
auditory system. Its function is to transfer the sound waves through
the ear canal to provide sufficient stimulus to the fluids of the inner
ear. Degradation of the ossicles that transmit these sound waves from
the eardrum to the inner ear leads to hearing loss. This problem can
be overcome by replacing one or more of these ossicles by middleear
prosthesis. Designing such prosthesis requires a comprehensive
knowledge of the biomechanics of the middle-ear. There are many
finite element modeling approaches developed to understand the
biomechanics of the middle ear. The available models in the
literature, involve high computation time. In this paper, we propose a
simplified model which provides a reasonably accurate result with
much less computational time. Simulation results indicate a
maximum sound pressure gain of 10 dB at 5500 Hz.
Abstract: The enthusiasm for gluten avoidance in a growing
market is met by improvements in sensitive detection methods for
analysing gluten content. Paradoxically, manufacturers employ no
such systems in the production process but continue to market their
product as gluten free, a significant risk posed to an undetermined
coeliac population. This paper resonates with an immunological
response that causes gastrointestinal scarring and villous atrophy with
the conventional description of personal injury. This thesis divulges
into evaluating potential inadequacies of gluten labelling laws which
not only present a diagnostic challenge for general practitioners in the
UK but it also exposes a less than adequate form of available legal
protection to those who suffer adverse reactions as a result of gluten
digestion. Central to this discussion is whether a claim brought in
misrepresentation, negligence and/or under the Consumer Protection
Act 1987 could be sustained. An interesting comparison is then made
with the legal regimes of neighboring jurisdictions furthering the
theme of a legally un-catered for gluten kingdom.
Abstract: This paper deals with the synthesis of fuzzy controller
applied to a permanent magnet synchronous machine (PMSM) with a
guaranteed H∞ performance. To design this fuzzy controller,
nonlinear model of the PMSM is approximated by Takagi-Sugeno
fuzzy model (T-S fuzzy model), then the so-called parallel
distributed compensation (PDC) is employed. Next, we derive the
property of the H∞ norm. The latter is cast in terms of linear matrix
inequalities (LMI-s) while minimizing the H∞ norm of the transfer
function between the disturbance and the error ( ) ev T . The
experimental and simulations results were conducted on a permanent
magnet synchronous machine to illustrate the effects of the fuzzy
modelling and the controller design via the PDC.
Abstract: The medical studies often require different methods
for parameters selection, as a second step of processing, after the
database-s designing and filling with information. One common
task is the selection of fields that act as risk factors using wellknown
methods, in order to find the most relevant risk factors and
to establish a possible hierarchy between them. Different methods
are available in this purpose, one of the most known being the
binary logistic regression. We will present the mathematical
principles of this method and a practical example of using it in the
analysis of the influence of 10 different psychiatric diagnostics
over 4 different types of offences (in a database made from 289
psychiatric patients involved in different types of offences).
Finally, we will make some observations about the relation
between the risk factors hierarchy established through binary
logistic regression and the individual risks, as well as the results of
Chi-squared test. We will show that the hierarchy built using the
binary logistic regression doesn-t agree with the direct order of risk
factors, even if it was naturally to assume this hypothesis as being
always true.
Abstract: In this study, we report the synthesis and
characterization of nanohydroxyapatite (nHAp) in gelatin-starch
matrix via biomimetic method. Characterization of the samples was
performed using X-ray diffraction (XRD) and Fourier Transform
infrared spectroscopy (FT-IR). The Size and morphology of the
nHAp samples were determined using scanning and transmission
electron microscopy (SEM and TEM). The results reveal that the
shape and morphology of nHAp is influenced by presence of
biopolymers as template. Carbonyl and amino groups from gelatin
and hydroxyl from starch play crucial roles in HAp formation on the
surface of gelatin-starch.
Abstract: Based on a global kinetics of direct dimethyl ether (DME) synthesis process from syngas, a steady-state one-dimensional mathematical model for the bubble column slurry reactor (BCSR) has been established. It was built on the assumption of plug flow of gas phase, sedimentation-dispersion model of catalyst grains and isothermal chamber regardless of reaction heats and rates for the design of an industrial scale bubble column slurry reactor. The simulation results indicate that higher pressure and lower temperature were favorable to the increase of CO conversion, DME selectivity, products yield and the height of slurry bed, which has a coincidence with the characteristic of DME synthesis reaction system, and that the height of slurry bed is lessen with the increasing of operation temperature in the range of 220-260℃. CO conversion, the optimal operation conditions in BCSR were proposed.
Abstract: The subcellular organelles called oil bodies (OBs) are lipid-filled quasi-spherical droplets produced from the endoplasmic reticulum (ER) and then released into the cytoplasm during seed development. It is believed that an OB grows by coalescence with other OBs and that its stability depends on the composition of oleosins, major proteins inserted in the hemi membrane that covers OBs. In this study, we measured the OB-volume distribution from different genotypes of A. thaliana after 7, 8, 9, 10 and 11 days of seed development. In order to test the hypothesis of OBs dynamics, we developed a simple mathematical model using non-linear differential equations inspired from the theory of coagulation. The model describes the evolution of OB-volume distribution during the first steps of seed development by taking into consideration the production of OBs, the increase of triacylglycerol volume to be stored, and the growth by coalescence of OBs. Fitted parameters values show an increase in the OB production and coalescence rates in A. thaliana oleosin mutants compared to wild type.