Abstract: Hydraulic fracturing is one of the most important
stimulation techniques available to the petroleum engineer to extract
hydrocarbons in tight gas sandstones. It allows more oil and gas
production in tight reservoirs as compared to conventional means.
The main aim of the study is to optimize the hydraulic fracturing as
technique and for this purpose three multi-zones layer formation is
considered and fractured contemporaneously. The three zones are
named as Zone1 (upper zone), Zone2 (middle zone) and Zone3
(lower zone) respectively and they all occur in shale rock. Simulation was performed with Mfrac integrated software which
gives a variety of 3D fracture options. This simulation process
yielded an average fracture efficiency of 93.8%for the three
respective zones and an increase of the average permeability of the
rock system. An average fracture length of 909 ft with net height
(propped height) of 210 ft (average) was achieved. Optimum
fracturing results was also achieved with maximum fracture width of
0.379 inches at an injection rate of 13.01 bpm with 17995 Mscf of
gas production.
Abstract: One of the challenges that higher education faces is to
find how to approach the sustainability in an inclusive way to the
student within all the different academic areas, how to move the
sustainable development from the abstract field to the operational
field. This research comes from the ecoliteracy and the pedagogical
praxis as tools for rebuilding the teaching processes inside of
universities. The purpose is to determine and describe which are the
factors involved in the process of learning particularly in the
Greenhouse-School Siembra UV. In the Greenhouse-School Siembra UV, of the University of
Veracruz, are cultivated vegetables, medicinal plants and small
cornfields under the usage of eco-technologies such as hydroponics,
Wickingbed and Hugelkultur, which main purpose is the saving of
space, labor and natural resources, as well as function as agricultural
production alternatives in the urban and periurban zones. The sample was formed with students from different academic
areas and who are actively involved in the greenhouse, as well as
institutes from the University of Veracruz and governmental and nongovernmental
departments. This project comes from a pedagogic praxis approach, from filling
the needs that the different professional profiles of the university
students have. All this with the purpose of generate a pragmatic
dialogue with the sustainability. It also comes from the necessity to
understand the factors that intervene in the students’ praxis. In this
manner is how the students are the fundamental unit in the sphere of
sustainability. As a result, it is observed that those University of Veracruz
students who are involved in the Greenhouse-school, Siembra UV,
have enriched in different levels the sense of urban and periurban
agriculture because of the diverse academic approaches they have
and the interaction between them. It is concluded that the ecotechnologies
act as fundamental tools for ecoliteracy in society,
where it is strengthen the nutritional and food security from a
sustainable development approach.
Abstract: Cryosorption pumps are considered safe, quiet, and
ultra-high vacuum production pumps which have their application
from Semiconductor industries to ITER [International Thermonuclear
Experimental Reactor] units. The principle of physisorption of gases
over highly porous materials like activated charcoal at cryogenic
temperatures (below -1500°C) is involved in determining the
pumping speed of gases like Helium, Hydrogen, Argon, and
Nitrogen. This paper aims at providing detailed overview of
development of Cryosorption pump and characterization of different
activated charcoal materials that optimizes the performance of the
pump. Different grades of charcoal were tested in order to determine
the pumping speed of the pump and were compared with
commercially available Varian cryopanel. The results for bare panel,
bare panel with adhesive, cryopanel with pellets, and cryopanel with
granules were obtained and compared. The comparison showed that
cryopanel adhered with small granules gave better pumping speeds
than large sized pellets.
Abstract: Evolutionary Algorithms (EAs) have been used
widely through evolution theory to discover acceptable solutions that
corresponds to challenges such as natural resources management.
EAs are also used to solve varied problems in the real world. EAs
have been rapidly identified for its ease in handling multiple
objective problems. Reservoir operations is a vital and researchable
area which has been studied in the last few decades due to the limited
nature of water resources that is found mostly in the semi-arid
regions of the world. The state of some developing economy that
depends on electricity for overall development through hydropower
production, a renewable form of energy, is appalling due to water
scarcity. This paper presents a review of the applications of
evolutionary algorithms to reservoir operation for hydropower
production. This review includes the discussion on areas such as
genetic algorithm, differential evolution, and reservoir operation. It
also identified the research gaps discovered in these areas. The results
of this study will be an eye opener for researchers and decision
makers to think deeply of the adverse effect of water scarcity and
drought towards economic development of a nation. Hence, it
becomes imperative to identify evolutionary algorithms that can
address this issue which can hamper effective hydropower
generation.
Abstract: Revenue leakages are one of the major challenges
manufacturers face in production processes, as most of the input
materials that should emanate as products from the lines are lost as
waste. Rather than generating income from material input which is
meant to end-up as products, losses are further incurred as costs in
order to manage waste generated. In addition, due to the lack of a
clear view of the flow of resources on the lines from input to output
stage, acquiring information on the true cost of waste generated have
become a challenge. This has therefore given birth to the
conceptualization and implementation of waste minimization
strategies by several manufacturing industries. This paper reviews the
principles and applications of three environmental management
accounting tools namely Activity-based Costing (ABC), Life-Cycle
Assessment (LCA) and Material Flow Cost Accounting (MFCA) in
the manufacturing industry and their effectiveness in curbing revenue
leakages. The paper unveils the strengths and limitations of each of
the tools; beaming a searchlight on the tool that could allow for
optimal resource utilization, transparency in production process as
well as improved cost efficiency. Findings from this review reveal
that MFCA may offer superior advantages with regards to the
provision of more detailed information (both in physical and
monetary terms) on the flow of material inputs throughout the
production process compared to the other environmental accounting
tools. This paper therefore makes a case for the adoption of MFCA as
a viable technique for the identification and reduction of waste in
production processes, and also for effective decision making by
production managers, financial advisors and other relevant
stakeholders.
Abstract: This study aims to assess the students' needs for the
tour planning e-guide. The study is developing on the contribution
and importance of the Educational Tour Planning Guide (ETP) is a
multimedia course ware as one of the effective methods in teaching
and learning of environmental science among the students in primary
schools of the Ministry of Education, Malaysia. It is to provide the
student with knowledge and experience about tourism, environmental
science activities and process. E-guide to ETP also hopes to
strengthen the student understanding toward the subject learn in the
tourism environmental science. In order to assess the student's needs
on the e-Guide to Educational Tour Planning in Environmental
Science, the study has produced a similar e-Guide to ETP in the form
as a course ware to be tested during the study. The study has involved
several steps in order to be completed. It is such as the formulation of
the problem, the review of the literature, the formulation of the study
methodology, the production of the e-Guide to ETP, field survey and
finally the analyses and discussion made on the data gathered during
the study. The survey has involved 100 respondents among the
students in standard six primary schools in Kluang Johor. Through
the findings, the study indicates that the current tested product is
acceptable among the students in learning environmental science as a
guide to plan for the tour. The findings also show a slight difference
between the respondents who are using the e-Guide to ETP, and those
who are not on the basis of the e-Guide to ETP results. Due the
important for the study, the researcher hopes to be having a fair
discussion and excellence, recommendation for the development of
the product of the current study. This report is written also important
to provide a written reference for the future related study.
Abstract: Polylactic acid (PLA) is the most commercially
available bio-based and biodegradable plastic at present. PLA has
been used in plastic related industries including single-used
containers, disposable and environmentally friendly packaging owing
to its renewability, compostability, biodegradability, and safety.
Although PLA demonstrates reasonably good optical, physical,
mechanical and barrier properties comparable to the existing
petroleum-based plastics, its brittleness and mold shrinkage as well as
its price are the points to be concerned for the production of rigid and
semi-rigid packaging. Blending PLA with other bio-based polymers
including thermoplastic starch (TPS) is an alternative not only to
achieve a complete bio-based plastic, but also to reduce the
brittleness, shrinkage during molding and production cost of the
PLA-based products. TPS is a material produced mainly from starch
which is cheap, renewable, biodegradable, compostable, and nontoxic.
It is commonly prepared by a plasticization of starch under
applying heat and shear force. Although glycerol has been reported as
one of the most plasticizers used for preparing TPS, its migration
caused the surface stickiness of the TPS products. In some cases,
mixed plasticizers or natural fibers have been applied to impede the
retrogradation of starch or reduce the migration of glycerol. The
introduction of fibers into TPS-based materials could reinforce the
polymer matrix as well. Therefore, the objective of the present
research is to study the effect of starch type (i.e. native starch and
phosphate starch), plasticizer type (i.e. glycerol and xylitol with a
weight ratio of glycerol to xylitol of 100:0, 75:25, 50:50, 25:75 and
0:100) and fiber content (i.e. in the range of 1-25 %wt) on properties
of PLA/TPS blend and composite. PLA/TPS blends and composites
were prepared using a twin-screw extruder and then converted into
dumbbell-shaped specimens using an injection molding machine. The
PLA/TPS blends prepared by using phosphate starch showed higher
tensile strength and stiffness than the blends prepared by using native
one. In contrast, the blends from native starch exhibited higher
extensibility and heat distortion temperature (HDT) than those from
the modified starch. Increasing xylitol content resulted in enhanced
tensile strength, stiffness and water resistance, but decreased
extensibility and HDT of the PLA/TPS blend. Tensile properties and
hydrophobicity of the blend could be improved by incorporating
silane treated-jute fibers.
Abstract: Rapid prototyping is a new group of manufacturing
processes, which allows fabrication of physical of any complexity
using a layer by layer deposition technique directly from a computer
system. The rapid prototyping process greatly reduces the time and
cost necessary to bring a new product to market. The prototypes
made by these systems are used in a range of industrial application
including design evaluation, verification, testing, and as patterns for
casting processes. These processes employ a variety of materials and
mechanisms to build up the layers to build the part. The present work
was to build a FDM prototyping machine that could control the X-Y
motion and material deposition, to generate two-dimensional and
three-dimensional complex shapes. This study focused on the
deposition of wax material. This work was to find out the properties
of the wax materials used in this work in order to enable better
control of the FDM process. This study will look at the integration of
a computer controlled electro-mechanical system with the traditional
FDM additive prototyping process. The characteristics of the wax
were also analysed in order to optimise the model production process.
These included wax phase change temperature, wax viscosity and
wax droplet shape during processing.
Abstract: The ferrites ZnFe2O4, CdFe2O4 and CuFe2O4 are
synthesized in laboratory conditions using ceramic technology. Their
homogeneity and structure are proven by X-Ray diffraction analysis
and Mössbauer spectroscopy. The synthesized ferrites are subjected
to strong acid and high temperature leaching with solutions of H2SO4,
HCl and HNO3. The results indicate that the highest degree of
leaching of Zn, Cd and Cu from the ferrites is achieved by use of
HCl. The charging of five zinc sulfide concentrates was optimized using
the criterion of minimal amount of zinc ferrite produced when
roasting the concentrates in a fluidized bed. The results obtained are
interpreted in terms of the hydrometallurgical zinc production and
maximum recovery of zinc, copper and cadmium from initial zinc
concentrates after their roasting.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: Growing human population has placed increased
demands on water supplies and spurred a heightened interest in
desalination infrastructure. Key elements of the economics of
desalination projects are thermal and electrical inputs. With growing
concerns over use of fossil fuels to (indirectly) supply these inputs,
coupling of desalination with nuclear power production represents a
significant opportunity. Individually, nuclear and desalination
technologies have a long history and are relatively mature. For
desalination, Reverse Osmosis (RO) has the lowest energy inputs.
However, the economically driven output quality of the water
produced using RO, which uses only electrical inputs, is lower than the
output water quality from thermal desalination plants. Therefore,
modern desalination projects consider that RO should be coupled with
thermal desalination technologies (MSF, MED, or MED-TVC) with
attendant steam inputs to permit blending to produce various qualities
of water. A large nuclear facility is well positioned to dispatch large
quantities of both electrical and thermal power. This paper considers
the supply of thermal energy to a large desalination facility to examine
heat balance impact on the nuclear steam cycle. The APR1400 nuclear
plant is selected as prototypical from both a capacity and turbine cycle
heat balance perspective to examine steam supply and the impact on
electrical output. Extraction points and quantities of steam are
considered parametrically along with various types of thermal
desalination technologies to form the basis for further evaluations of
economically optimal approaches to the interface of nuclear power
production with desalination projects. In our study, the
thermodynamic evaluation will be executed by DE-TOP, an IAEA
sponsored program. DE-TOP has capabilities to analyze power
generation systems coupled to desalination plants through various
steam extraction positions, taking into consideration the isolation loop
between the nuclear and the thermal desalination facilities (i.e., for
radiological isolation).
Abstract: Processing of high-silicon bauxite on the base of the
traditional clinkering method is related to high power consumption
and capital investments, which makes production of alumina from
those ores non-competitive in terms of basic economic showings. For
these reasons, development of technological solutions enabling to
process bauxites with various chemical and mineralogical structures
efficiently with low level of thermal power consumption is important.
Flow sheet of the studies on washability of ores from the Timanskoe
and the Severo-Onezhskoe deposits is on the base of the flotation
method.
Abstract: Cholera is a disease that is predominately common in
developing countries due to poor sanitation and overcrowding
population. In this paper, a deterministic model for the dynamics of
cholera is developed and control measures such as health educational
message, therapeutic treatment, and vaccination are incorporated in
the model. The effective reproduction number is computed in terms
of the model parameters. The existence and stability of the
equilibrium states, disease free and endemic equilibrium states are
established and showed to be locally and globally asymptotically
stable when R0 < 1 and R0 > 1 respectively. The existence of
backward bifurcation of the model is investigated. Furthermore,
numerical simulation of the model developed is carried out to show
the impact of the control measures and the result indicates that
combined control measures will help to reduce the spread of cholera
in the population.
Abstract: An industrial system for the production of white
liquor of a paper industry, Klabin Paraná Papéis, formed by ten
reactors was modeled, simulated, and analyzed. The developed model
considered possible water losses by evaporation and reaction, in
addition to variations in volumetric flow of lime mud across the
reactors due to composition variations. The model predictions agreed
well with the process measurements at the plant and the results
showed that the slaking reaction is nearly complete at the third
causticizing reactor, while causticizing ends by the seventh reactor.
Water loss due to slaking reaction and evaporation occurs more
pronouncedly in the slaking reaction than in the final causticizing
reactors; nevertheless, the lime mud flow remains nearly constant
across the reactors.
Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: Food supply chain is one of the most complex supply
chain networks due to its perishable nature and customer oriented
products, and food safety is the major concern for this industry. IT
system could help to minimize the production and consumption of
unsafe food by controlling and monitoring the entire system.
However, there have been many issues in adoption of IT system in
this industry specifically within SMEs sector. With this regard, this
study presents a novel approach to use IT and tractability systems in
the food supply chain, using application of RFID and central
database.
Abstract: This research studies the joint production,
maintenance and subcontracting control policy for an unreliable
deteriorating manufacturing system. Production activities are
controlled by a derivation of the Hedging Point Policy, and given that
the system is subject to deterioration, it reduces progressively its
capacity to satisfy product demand. Multiple deterioration effects are
considered, reflected mainly in the quality of the parts produced and
the reliability of the machine. Subcontracting is available as support
to satisfy product demand; also, overhaul maintenance can be
conducted to reduce the effects of deterioration. The main objective
of the research is to determine simultaneously the production,
maintenance and subcontracting rate, which minimize the total,
incurred cost. A stochastic dynamic programming model is
developed and solved through a simulation-based approach
composed of statistical analysis and optimization with the response
surface methodology. The obtained results highlight the strong
interactions between production, deterioration and quality, which
justify the development of an integrated model. A numerical example
and a sensitivity analysis are presented to validate our results.
Abstract: Biomass treatment through densification is very suitable and helpful technology before its effective energy recovery. Densification process of biomass is significantly influenced by various technological and material variables, which are ultimately reflected on the final solid biofuels quality. The paper deals with the experimental research of the relationship between technological and material variables during densification of fast-growing trees, roundly fast-growing willows. The main goal of presented experimental research is to determine the relationship between compression pressure and raw material particle size from a final briquettes density point of view. Experimental research was realized by single-axis densification. The impact of particle size with interaction of compression pressure and stabilization time on the quality properties of briquettes was determined. These variables interaction affects the final solid biofuels (briquettes) quality. From briquettes production point of view and from densification machines constructions point of view is very important to know about mutual interaction of these variables on final briquettes quality. The experimental findings presented here are showing the importance of mentioned variables during the densification process.
Abstract: This paper contributes to the ongoing debate as to the relevance of translation studies to professional practitioners. It exposes the various misconceptions permeating the links between theory and practice in the translation landscape in the Arab World. It is a thesis of this paper that specialization in translation should be redefined; taking account of the fact, that specialized knowledge alone is neither crucial nor sufficient in technical translation. It should be tested against the readability of the translated text, the appropriateness of its style and the usability of its content by endusers to carry out their intended tasks. The paper also proposes a preliminary model to establish a working link between theory and practice from the perspective of professional trainers and practitioners, calling for the latter to participate in the production of knowledge in a systematic fashion. While this proposal is driven by a rather intuitive conviction, a research line is needed to specify the methodological moves to establish the mediation strategies that would relate the components in the model of knowledge transfer proposed in this paper.
Abstract: Effect of alloying on the microstructure and mechanical properties of heat-resisting duplex stainless steel (DSS) for Mg production was investigated in this study. 25Cr-8Ni based DSS’s were cast into rectangular ingots of which the dimension was 350×350×100 mm3 . Nitrogen and Yttrium were added in the range within 0.3 in weight percent. Phase equilibrium was calculated using the FactSage®, thermodynamic software. Hot exposure, high temperature tensile and compression tests were conducted on the ingots at 1230oC, which is operation temperature employed for Mg production by Silico-thermic reduction. The steel with N and Y showed much higher strength than 310S alloy in both tensile and compression tests. By thermal exposition at 1230oC for 200 hrs, hardness of DSS containing N and Y was found to increase. Hot workability of the heat-resisting DSS was evaluated by employing hot rolling at 1230 oC. Hot shortness was observed in the ingot with N and found to disappear after addition of Y.