Abstract: The recommended limit for cadmium concentration in
potable water is less than 0.005 mg/L. A continuous biosorption
process using indigenous red seaweed, Gracilaria corticata, was
performed to remove cadmium from the potable water. The process
was conducted under fixed conditions and the breakthrough curves
were achieved for three consecutive sorption-desorption cycles. A
modeling based on Artificial Neural Network (ANN) was employed
to fit the experimental breakthrough data. In addition, a simplified
semi empirical model, Thomas, was employed for this purpose. It
was found that ANN well described the experimental data (R2>0.99)
while the Thomas prediction were a bit less successful with R2>0.97.
The adjusted design parameters using the nonlinear form of Thomas
model was in a good agreement with the experimentally obtained
ones. The results approve the capability of ANN to predict the
cadmium concentration in potable water.
Abstract: TiO2 thin films have been prepared by the sol-gel dipcoating
technique in order to elaborate antireflective thin films for
monocrystalline silicon (mono-Si). The titanium isopropoxyde was
chosen as a precursor with hydrochloric acid as a catalyser for
preparing a stable solution. The optical properties have been tailored
with varying the solution concentration, the withdrawn speed, and the
heat-treatment. We showed that using a TiO2 single layer with 64.5
nm in thickness, heat-treated at 450°C or 300°C reduces the mono-Si
reflection at a level lower than 3% over the broadband spectral
domains [669-834] nm and [786-1006] nm respectively. Those latter
performances are similar to the ones obtained with double layers of
low and high refractive index glasses respectively.
Abstract: We present an analytical model for the calculation of
the sensitivity, the spectral current noise and the detective parameter
for an optically illuminated In0.53Ga0.47As n+nn+ diode. The
photocurrent due to the excess carrier is obtained by solving the
continuity equation. Moreover, the current noise level is evaluated at
room temperature and under a constant voltage applied between the
diode terminals. The analytical calculation of the current noise in the
n+nn+ structure is developed by considering the free carries
fluctuations. The responsivity and the detection parameter are
discussed as functions of the doping concentrations and the emitter
layer thickness in one-dimensional homogeneous n+nn+ structure.
Abstract: Lead being a toxic heavy metal that mankind is
exposed to the highest levels of this metal from environmental
pollutants. A total of 180 Male scalp hair samples were collected
from different environments in Greater Cairo (GC), i.e. industrial,
heavy traffic and rural areas (60 samples from each) having different
activities during the period of, 1/5/2010 to 1/11/2012. Hair samples
were collected during five stages. Data proved that the concentration
of lead in male industrial areas of Cairo ranged between 6.2847 to
19.0432 μg/g, with mean value of 12.3288 μg/g. On the other hand,
lead content of hair samples of residential-traffic areas ranged
between 2.8634 to 16.3311 μg/g with mean value of 9.7552 μg/g.
While lead concentration on the hair of the male residents living in
rural area ranged between 1.0499-9.0402μg/g with mean value of
4.7327 μg/g. The Pb concentration in scalp hair of Cairo residents of
residential-traffic and rural traffic areas was observed to follow the
same pattern. The pattern was that of decrease concentration of
summer and its increase in winter. Then, there was a marked increase
in Pb concentration of summer 2012, and this increase was
significant. These were obviously seen for the residential-traffic and
rural areas residents. Pb pollution in residents of industrial areas
showed the same seasonal pattern, but there was marked to decrease
in Pb concentration of summer 2012, and this decrease was
significant. Lead pollution in residents of GC was serious. It is worth
noting that the atmosphere is still contaminated by lead despite a
decade of using unleaded gasoline. Strong seasonal variation in
higher Pb concentration on winter than in summer was found. Major
contributions to the pollution with Pb could include industry
emissions, motor vehicle emissions and long transported dust from
outside Cairo. More attention should be paid to the reduction of Pb
content of the urban aerosol and to the Pb pollution health.
Abstract: The study is devoted to define the optimal conditions
for the nitriding of pure iron at atmospheric pressure by using NH3-
Ar-C3H8 gas mixtures. After studying the mechanisms of phase
formation and mass transfer at the gas-solid interface, a mathematical
model is developed in order to predict the nitrogen transfer rate in the
solid, the ε-carbonitride layer growth rate and the nitrogen and
carbon concentration profiles. In order to validate the model and to
show its possibilities, it is compared with thermogravimetric
experiments, analyses and metallurgical observations (X-ray
diffraction, optical microscopy and electron microprobe analysis).
Results obtained allow us to demonstrate the sound correlation
between the experimental results and the theoretical predictions.
Abstract: Many of the ever-growing elderly population require
exercise, such as running, for health management. One important
element of a runner’s training is the choice of shoes for exercise; shoes
are important because they provide the interface between the feet and
road. When we purchase shoes, we may instinctively choose a pair
after trying on many different pairs of shoes. Selecting the shoes
instinctively may work, but it does not guarantee a suitable fit for
running activities. Therefore, if we could select suitable shoes for each
runner from the viewpoint of brain activities, it would be helpful for
validating shoe selection. In this paper, we describe how brain
activities show different characteristics during particular task,
corresponding to different properties of shoes. Using five subjects, we
performed a verification experiment, applying weight, softness, and
flexibility as shoe properties. In order to affect the shoe property’s
differences to the brain, subjects run for 10 min. Before and after
running, subjects conducted a paced auditory serial addition task
(PASAT) as the particular task; and the subjects’ brain activities
during the PASAT are evaluated based on oxyhemoglobin and
deoxyhemoglobin relative concentration changes, measured by
near-infrared spectroscopy (NIRS). When the brain works actively,
oxihemoglobin and deoxyhemoglobin concentration drastically
changes; therefore, we calculate the maximum values of concentration
changes. In order to normalize relative concentration changes after
running, the maximum value are divided by before running maximum
value as evaluation parameters. The classification of the groups of
shoes is expressed on a self-organizing map (SOM). As a result,
deoxyhemoglobin can make clusters for two of the three types of
shoes.
Abstract: Reburning is a useful technology in reducing nitric
oxide through injection of a secondary hydrocarbon fuel. In this paper,
an experimental study has been conducted to evaluate the effect of fuel
lean reburning on NOx/CO reduction in LNG flame. Experiments
were performed in flames stabilized by a co-flow swirl burner, which
was mounted at the bottom of the furnace. Tests were conducted using
LNG gas as the reburn fuel as well as the main fuel. The effects of
reburn fuel fraction and injection manner of the reburn fuel were
studied when the fuel lean reburning system was applied. The paper
reports data on flue gas emissions and temperature distribution in the
furnace for a wide range of experimental conditions. At steady state,
temperature distribution and emission formation in the furnace have
been measured and compared. This paper makes clear that in order to
decrease both NOx and CO concentrations in the exhaust when the
pulsated fuel lean reburning system was adapted, it is important that
the control of some factors such as frequency and duty ratio. Also it
shows the fuel lean reburning is also effective method to reduce NOx
as much as reburning.
Abstract: Two types of glass fibers having different lengths
(1/16" and 1/32") were added into rigid PVC foams to enhance the
dimensional stability of extruded rigid Polyvinyl Chloride (PVC)
foam at different concentrations (0-20 phr) using a single screw
profile extruder. PVC foam-glass fiber composites (PVC-GF) were
characterized for their dimensional stability, structural, thermal, and
mechanical properties. Experimental results show that the
dimensional stability, heat resistance, and storage modulus were
enhanced without compromising the tensile and flexural strengths of
the composites. Overall, foam composites which were prepared with
longer glass fibers exhibit better mechanical and thermal properties
than those prepared with shorter glass fibers due to higher
interlocking between the fibers and the foam cells, which result in
better load distribution in the matrix.
Abstract: In this work, a polyaniline/Iron oxide (PANI/Fe2O3)
composite was chemically prepared by oxidative polymerization of
aniline in acid medium, in presence of ammonium persulphate as an
oxidant and amount of Fe2O3. The composite was characterized by a
scanning electron microscopy (SEM). The prepared composite has
been used as adsorbent to remove Tartrazine dye form aqueous
solutions.
The effects of initial dye concentration and temperature on the
adsorption capacity of PANI/Fe2O3 for Tartrazine dye have been
studied in this paper.
The Langmuir and Freundlich adsorption models have been used
for the mathematical description of adsorption equilibrium data. The
best fit is obtained using the Freundlich isotherm with an R2 value of
0.998. The change of Gibbs energy, enthalpy, and entropy of
adsorption has been also evaluated for the adsorption of Tartrazine
onto PANI/ Fe2O3. It has been proved according the results that the
adsorption process is endothermic in nature.
Abstract: Due to the determination of the pollution status of
fresh resources in the Egyptian territorial waters is very important for
public health; this study was carried out to reveal the levels of heavy
metals in the shellfish and their environment and its relation to the
highly developed industrial activities in those areas. A total of 100
shellfish samples from the Rosetta, Edku, El-Maadiya, Abo-Kir and
El-Max coasts [10 crustaceans (shrimp) and 10 mollusks (oysters)]
were randomly collected from each coast. Additionally, 10 samples
from both the water and the sediment were collected from each coast.
Each collected sample was analyzed for cadmium, chromium,
copper, lead and zinc residues using a Perkin Elmer atomic
absorption spectrophotometer (AAS). The results showed that the
levels of heavy metals were higher in the water and sediment from
Abo-Kir. The heavy metal levels decreased successively for the
Rosetta, Edku, El-Maadiya, and El-Max coasts, and the
concentrations of heavy metals, except copper and zinc, in shellfish
exhibited the same pattern. For the concentration of heavy metals in
shellfish tissue, the highest was zinc and the concentrations decreased
successively for copper, lead, chromium and cadmium for all coasts,
except the Abo-Kir coast, where the chromium level was highest and
the other metals decreased successively for zinc, copper, lead and
cadmium. In Rosetta, chromium was higher only in the mollusks,
while the level of this metal was lower in the crustaceans; this trend
was observed at the Edku, El-Maadiya and El-Max coasts as well.
Herein, we discuss the importance of such contamination for public
health and the sources of shellfish contamination with heavy metals.
We suggest measures to minimize and prevent these pollutants in the
aquatic environment and, furthermore, how to protect humans from
excessive intake.
Abstract: In recent decades with the development of technology
and lack of food sources, sewage sludge in production of human
foods is inevitable. Various sources of municipal and industrial
sewage sludge that is produced can provide the requirement of plant
nutrients. Soils in arid, semi-arid climate of central Iran that most
affected by water drainage, iron and zinc deficiencies, using of
sewage sludge is helpful. Therefore, the aim of this study is
investigation of sewage sludge and manure application on Ni, Pb and
Cd uptake by Savory. An experiment in a randomized complete block
design with three replications was performed. Sewage sludge
treatments consisted of four levels, control, 15, 30, 80 tons per
hectares; the manure was used in four levels of control, 20, 40 and 80
tons per hectare. Results showed that the wet and dry weights was not
affected by sewage sludge using, while, manure has significant effect
on them. The effect of sewage sludge on the cadmium and lead
concentrations were significant. Interactions of sewage sludge and
manure on dry weight values were not significant. Compare mean
analysis showed that increasing the amount of sewage sludge had no
significant effect on cadmium concentration and it reduced when
sewage sludge usage increased. This is probably due to increased
plant growth and reduced concentrations of these elements in the
plant.
Abstract: Pesticides and drugs used in agriculture and veterinary
medicine may end up in aquatic environments and bioaccumulate in
the food chain, thus causing serious problems for fauna and human
health. For determination of the toxic effects of atrazine herbicide on
Caspian kutum, Rutilus frisii kutum larvae, the 96-h LC50 of atrazine
was measured for newly hatched larvae as 18.53 ppm. Toxicity of
atrazine herbicide on Caspian kutum larvae was investigated using
concentrations: 9.25ppm, 4.62 ppm and 2.31 ppm for 7 days.
Comparison of the length, weight and condition factor showed that
no significant differences between atrazine exposed and control
groups. The concentration of Na+, K+, Ca2+, Mg2+ and Cl- in whole
body of larvae in control and atrazine exposure groups were
measured and the results showed that concentrations of all these ions
is higher in atrazine exposure group than control group. It is obvious
from this study that atrazine negatively affects osmoregulation
process and changes ion compositions of the body even at sublethal
concentration and acute exposure but have no effects on growth
parameters of the body.
Abstract: The aim of the present work was to statistically design
an autotrophic medium for maximum biomass production by
Chlorella pyrenoidosa using response surface methodology. After
evaluating one factor at a time approach, K2HPO4, KNO3,
MgSO4.7H2O and NaHCO3 were preferred over the other
components of the fog’s medium as most critical autotrophic medium
components. The study showed that the maximum biomass yield was
achieved while the concentrations of MgSO4.7H2O, K2HPO4, KNO3
and NaHCO3 were 0.409 g/L, 0.24 g/L, 1.033 g/L, and 3.265 g/L,
respectively. The study reported that the biomass productivity of C.
pyrenoidosa improved from 0.14 g/L in defined fog’s medium to 1.40
g/L in modified fog’s medium resulting 10 fold increase. The
biochemical composition biosynthesis of C. pyrenoidosa was altered
using nitrogen limiting stress bringing about 5.23 fold increase in
lipid content than control (cell without stress), as analyzed by FTIR
integration method.
Abstract: The presence of endocrine-disrupting compounds,
such as bisphenol A (BPA), in the environment can cause serious
health problems. However, there are controversial opinions. This
study investigated the reproductive, metabolic, oxidative and
immunologic-disrupting effects of bisphenol A in male rabbits.
Rabbits were divided into five groups. The first four rabbit groups
were administered oral BPA (1, 10, 50, or 100 mg/kg/day) for ten
weeks. The fifth group was administered corn oil as the vehicle. BPA
significantly decreased serum testosterone, estradiol and the free
androgen index (FAI) and significantly increased sex hormone
binding globulin (SHBG) compared with the placebo group. The
higher doses of BPA showed a significant decrease in follicular
stimulating hormone (FSH) and luteinizing hormone (LH). A
significant increase in blood glucose levels was identified in the BPA
groups. The non-significant difference in insulin levels is a novel
finding. The cumulative testicular toxicity of BPA was clearly
demonstrated by the dose-dependent decrease in absolute testes
weight, primary measures of semen quality and a significant increase
in testicular malonaldehyde (MDA). Moreover, BPA significantly
decreased total antioxidant capacity (TAC) and significantly
increased immunoglobulin G (IgG) at the highest concentration. Our
results suggest that BPA, especially at higher doses, is associated
with many adverse effects on metabolism, oxidative stress, immunity,
sperm quality and markers of androgenic action.
Abstract: Calcium phosphate cement (CPC) is one of the most
attractive bioceramics due to its moldable and shape ability to fill
complicated bony cavities or small dental defect positions. In this
study, CPC was produced by using mixture of tetracalcium phosphate
(TTCP, Ca4O(PO4)2) and dicalcium phosphate anhydrous (DCPA,
CaHPO4) in equimolar ratio (1/1) with aqueous solutions of acetic
acid (C2H4O2) and disodium hydrogen phosphate dehydrate
(Na2HPO4.2H2O) in combination with sodium alginate in order to
improve theirs moldable characteristic. The concentration of the
aqueous solutions and sodium alginate were varied to investigate the
effect of different aqueous solutions and alginate on properties of the
cements. The cement paste was prepared by mixing cement powder
(P) with aqueous solution (L) in a P/L ratio of 1.0g/0.35ml. X-ray
diffraction (XRD) was used to analyses phase formation of the
cements. Setting time and compressive strength of the set CPCs were
measured using the Gilmore apparatus and Universal testing
machine, respectively.
The results showed that CPCs could be produced by using both
basic (Na2HPO4.2H2O) and acidic (C2H4O2) solutions. XRD results
show the precipitation of hydroxyapatite in all cement samples. No
change in phase formation among cements using difference
concentrations of Na2HPO4.2H2O solutions. With increasing
concentration of acidic solutions, samples obtained less
hydroxyapatite with a high dicalcium phosphate dehydrate leaded to
a shorter setting time. Samples with sodium alginate exhibited higher
crystallization of hydroxyapatite than that of without alginate as a
result of shorten setting time in a basic solution but a longer setting
time in an acidic solution. The stronger cement was attained from
samples using the acidic solution with sodium alginate; however the
strength was lower than that of using the basic solution.
Abstract: Heightened concerns over the amount of carbon
emitted from coal-related processes are generating shifts to the
application of biomass. In co-gasification, where coal is gasified
along with biomass, the biomass may be fed together with coal (cofeeding)
or an independent biomass gasifier needs to be integrated
with the coal gasifier. The main aim of this work is to evaluate the
biomass introduction methods in coal co-gasification. This includes
the evaluation of biomass concentration input (B0 to B100) and its
gasification performance. A process model is developed and
simulated in Aspen HYSYS, where both coal and biomass are
modelled according to its ultimate analysis. It was found that the
syngas produced increased with increasing biomass content for both
co-feeding and independent schemes. However, the heating values
and heat duties decreases with biomass concentration as more CO2
are produced from complete combustion.
Abstract: Food contamination occurs during post process
handling. This leads to spoilage and growth of pathogenic
microorganisms in the food, thereby reducing its shelf life or
spreading of food borne diseases. Several methods are tried and one
of which is use of antimicrobial packaging. Here, papain, a protease
enzyme, is covalently immobilized with the help of glutarldehyde on
polyurethane and used as a food wrap to protect food from microbial
contamination. Covalent immobilization of papain was achieved at a
pH of 7.4; temperature of 4°C; glutaraldehyde concentration of 0.5%;
incubation time of 24h; and 50mg of papain. The formation of -C=Nobserved
in the Fourier transform infrared spectrum confirmed the
immobilization of the enzyme on the polymer. Immobilized enzyme
retained higher activity than the native free enzyme. The modified
polyurethane showed better reduction of Staphylococcus aureus
biofilm than bare polymer film (eight folds reduction in live colonies,
two times reduction in protein and 6 times reduction in
carbohydrates). The efficacy of this was studied by wrapping it over
S. aureus contaminated cottage cheese (paneer) and cheese and
stored at a temperature of 4°C for 7days. The modified film reduced
the bacterial contamination by eight folds when compared to the bare
film. FTIR also indicated reduction in lipids, sugars and proteins in
the biofilm.
Abstract: An investigation into the effect of countersunk depth,
plate thickness, countersunk angle and plate width on the stress
concentration around countersunk hole is carried out with the help of
finite element analysis. The variation of stress concentration with
respect to these parameters is studied for three types of loading viz.
uniformly distributed load, uniformly varying load and functionally
distributed load. The results of the finite element analysis are
interpreted and some conclusions are drawn. The distribution of
stress concentration around countersunk hole in isotropic plates
simply supported at all the edges is found similar and is independent
of loading. The maximum stress concentration also occurs at a
particular point irrespective of the loading conditions.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.