Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: The organizations in the knowledge economy era have
recognized the importance of building knowledge assets for
sustainable growth and development. In comparison to other
industries, Information Technology (IT) enterprises, holds an edge in
developing an effective Knowledge Management (KM) programmethanks
to their in-house technological abilities. This paper tries to
study the various knowledge based incentive programmes and its
effect on Knowledge Sharing and Learning in the context of the
Indian IT sector. A conceptual model is developed linking KM
Incentives, Knowledge Sharing and Learning. A questionnaire study
is conducted to collect primary data from the knowledge workers of
the IT organizations located in India. The data was analysed using
Structural Equation Modeling using Partial Least Square method. The
results show a strong influence of knowledge management incentives
on knowledge sharing and an indirect influence on learning.
Abstract: The development of the United Arab Emirates (UAE)
into a regional trade, tourism, finance and logistics hub has
transformed its real estate markets. However, speculative activity and
price volatility remain concerns. UAE residential market values
(MV) are exposed to fluctuations in capital flows and migration
which, in turn, are affected by geopolitical uncertainty, oil price
volatility and global investment market sentiment. Internally, a
complex interplay between administrative boundaries, land tenure,
building quality and evolving location characteristics fragments UAE
residential property markets. In short, the UAE Residential Valuation
System (UAE-RVS) confronts multiple challenges to collect, filter
and analyze relevant information in complex and dynamic spatial and
capital markets. A robust (RVS) can mitigate the risk of unhelpful
volatility, speculative excess or investment mistakes. The research
outlines the institutional, ontological, dynamic and epistemological
issues at play. We highlight the importance of system capabilities,
valuation standard salience and stakeholders trust.
Abstract: The development of Drugs Delivery System (DDS)
has been widely investigated in the last decades. In this paper, first a
general overview of traditional and modern wound dressing is
presented. This is followed by a review of what scientists have done
in the medical environment, focusing on the possibility to develop a
new alternative for DDS through transdermal pathway, aiming to
treat melanoma skin cancer.
Abstract: A numerical study of natural convection heat transfer
in water filled cavity has been examined in 3-Dfor single phase liquid
cooling system by using an array of parallel plate fins mounted to one
wall of a cavity. The heat generated by a heat source represents a
computer CPU with dimensions of 37.5∗37.5mm mounted on
substrate. A cold plate is used as a heat sink installed on the opposite
vertical end of the enclosure. The air flow inside the computer case is
created by an exhaust fan. A turbulent air flow is assumed and k-ε
model is applied. The fins are installed on the substrate to enhance
the heat transfer. The applied power energy range used is between 15
- 40W. In order to determine the thermal behaviour of the cooling
system, the effect of the heat input and the number of the parallel
plate fins are investigated. The results illustrate that as the fin number
increases the maximum heat source temperature decreases. However,
when the fin number increases to critical value the temperature start
to increase due to the fins are too closely spaced and that cause the
obstruction of water flow. The introduction of parallel plate fins
reduces the maximum heat source temperature by 10% compared to
the case without fins. The cooling system maintains the maximum
chip temperature at 64.68°C when the heat input was at 40W that is
much lower than the recommended computer chips limit temperature
of no more than 85°C and hence the performance of the CPU is
enhanced.
Abstract: In this study, we have focused our attention on
combining of molecular imprinting into nanofilms and QCM
nanosensor approaches and producing QCM nanosensor for anti-
CCP, chosen as model protein, using anti-CCP imprinted nanofilms.
The nonimprinted nanosensor was also prepared to evaluate the
selectivity of the imprinted nanosensor. Anti-CCP imprinted QCM
nanosensor was tested for real time detection of anti-CCP from
aqueous solution. The kinetic and affinity studies were determined by
using anti-CCP solutions with different concentrations. The
responses related with mass shifts (%m) and frequency shifts (%f)
were used to evaluate adsorption properties. To show the selectivity
of the anti-CCP imprinted QCM nanosensor, competitive adsorption
of anti-CCP and IgM was investigated. The results indicate that anti-
CCP imprinted QCM nanosensor has higher adsorption capabilities
for anti-CCP than for IgM, due to selective cavities in the polymer
structure.
Abstract: Human motion capture has become one of the major
area of interest in the field of computer vision. Some of the major
application areas that have been rapidly evolving include the
advanced human interfaces, virtual reality and security/surveillance
systems. This study provides a brief overview of the techniques and
applications used for the markerless human motion capture, which
deals with analyzing the human motion in the form of mathematical
formulations. The major contribution of this research is that it
classifies the computer vision based techniques of human motion
capture based on the taxonomy, and then breaks its down into four
systematically different categories of tracking, initialization, pose
estimation and recognition. The detailed descriptions and the
relationships descriptions are given for the techniques of tracking and
pose estimation. The subcategories of each process are further
described. Various hypotheses have been used by the researchers in
this domain are surveyed and the evolution of these techniques have
been explained. It has been concluded in the survey that most
researchers have focused on using the mathematical body models for
the markerless motion capture.
Abstract: Environmental impact assessment techniques have
been developed as a result of the worldwide efforts to reduce the
environmental impact of global warming. By using the quantification
method in the construction industry, it is now possible to manage the
greenhouse gas is to systematically evaluate the impact on the
environment over the entire construction process. In particular, the
proportion of greenhouse gas emissions at the production stage of
construction material occupied is high, and efforts are needed in
particular in the construction field.
In this research, intended for concrete products for the construction
materials, by using the LCA method, we compared the results of
environmental impact assessment and carbon emissions of developing
products that have been applied low-carbon technologies compared to
existing products. As a results, by introducing a raw material of
industrial waste, showed carbon reduction. Through a comparison of
the carbon emission reduction effect of low carbon technologies, it is
intended to provide academic data for the evaluation of greenhouse
gases in the construction sector and the development of low carbon
technologies of the future.
Abstract: The purpose of this paper is to examine the hypothesis
explaining the mechanism in the case, where the product is deleted or
reduced the fundamental function of the product through the product
concept changes in the digital camera industry. This paper points out
not owning the fundamental technology might cause the change of the
product concept. Casio could create new competitive factor so that this
paper discusses a possibility of the mechanism of changing the product
concept.
Abstract: In this paper, an analysis of some model order
reduction techniques is presented. A new hybrid algorithm for model
order reduction of linear time invariant systems is compared with the
conventional techniques namely Balanced Truncation, Hankel Norm
reduction and Dominant Pole Algorithm (DPA). The proposed hybrid
algorithm is known as Clustering Dominant Pole Algorithm (CDPA),
is able to compute the full set of dominant poles and its cluster center
efficiently. The dominant poles of a transfer function are specific
eigenvalues of the state space matrix of the corresponding dynamical
system. The effectiveness of this novel technique is shown through
the simulation results.
Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.
Abstract: In order to study the aerodynamic performance of a
semi-flexible membrane wing, Fluid-Structure Interaction simulations
have been performed. The fluid problem has been modeled using
two different approaches which are the vortex panel method and the
numerical solution of the Navier-Stokes equations. Nonlinear analysis
of the structural problem is performed using the Finite Element
Method. Comparison between the two fluid solvers has been made.
Aerodynamic performance of the wing is discussed regarding its
lift and drag coefficients and they are compared with those of the
equivalent rigid wing.
Abstract: A computational fluid dynamics (CFD) model is
developed for rechargeable non-aqueous electrolyte lithium-air
batteries with a partial opening for oxygen supply to the cathode.
Multi-phase transport phenomena occurred in the battery are
considered, including dissolved lithium ions and oxygen gas in the
liquid electrolyte, solid-phase electron transfer in the porous
functional materials and liquid-phase charge transport in the
electrolyte. These transport processes are coupled with the
electrochemical reactions at the active surfaces, and effects of
discharge reaction-generated solid Li2O2 on the transport properties
and the electrochemical reaction rate are evaluated and implemented
in the model. The predicted results are discussed and analyzed in terms
of the spatial and transient distribution of various parameters, such as
local oxygen concentration, reaction rate, variable solid Li2O2 volume
fraction and porosity, as well as the effective diffusion coefficients. It
is found that the effect of the solid Li2O2 product deposited at the solid
active surfaces is significant on the transport phenomena and the
overall battery performance.
Abstract: This article is trying to determine the status of flue gas
that is entering the KWH heat exchanger from combustion chamber
in order to calculate the heat transfer ratio of the heat exchanger.
Combination of measurement, calculation and computer simulation
was used to create a useful way to approximate the heat transfer rate.
The measurements were taken by a number of sensors that are
mounted on the experimental device and by a thermal imaging
camera. The results of the numerical calculation are in a good
correspondence with the real power output of the experimental
device. That result shows that the research has a good direction and
can be used to propose changes in the construction of the heat
exchanger, but still needs enhancements.
Abstract: This study examines analytically the effect of tsunami loads on reinforced concrete (RC) frame buildings. The impact of tsunami wave loads and waterborne objects are analyzed using a typical substandard full-scale two-story RC frame building tested as part of the EU-funded Ecoleader project. The building was subjected to shake table tests in bare condition, and subsequently strengthened using Carbon Fiber Reinforced Polymers (CFRP) composites and retested. Numerical models of the building in both bare and CFRP-strengthened conditions are calibrated in DRAIN-3DX software to match the test results. To investigate the response of wave loads and impact forces, the numerical models are subjected to nonlinear dynamic analyses using force time-history input records. The analytical results are compared in terms of displacements at the floors and at the “impact point” of a boat. The results show that the roof displacement of the CFRP-strengthened building reduced by 63% when compared to the bare building. The results also indicate that strengthening only the mid-height of the impact column using CFRP is more effective at reducing damage when compared to strengthening other parts of the column. Alternative solutions to mitigate damage due to tsunami loads are suggested.
Abstract: This paper describes an analysis of Yacht Simulator
international trends and also explains about Yacht. The results are
summarized as follows. Attached to the cockpit are sensors that feed
-back information on rudder angle, boat heel angle and mainsheet
tension to the computer. Energy expenditure of the sailor measure
indirectly using expired gas analysis for the measurement of VO2 and
VCO2. At sea course configurations and wind conditions can be preset
to suit any level of sailor from complete beginner to advanced sailor.
Abstract: The air transport impact on environment is more than
ever a limitative obstacle to the aeronautical industry continuous
growth. Over the last decades, considerable effort has been carried
out in order to obtain quieter aircraft solutions, whether by changing
the original design or investigating more silent maneuvers. The
noise propagated by rotating surfaces is one of the most important
sources of annoyance, being present in most aerial vehicles. Bearing
this is mind, CEIIA developed a new computational chain for
noise prediction with in-house software tools to obtain solutions in
relatively short time without using excessive computer resources. This
work is based on the new acoustic tool, which aims to predict the
rotor noise generated during steady and maneuvering flight, making
use of the flexibility of the C language and the advantages of GPU
programming in terms of velocity. The acoustic tool is based in the
Formulation 1A of Farassat, capable of predicting two important
types of noise: the loading and thickness noise. The present work
describes the most important features of the acoustic tool, presenting
its most relevant results and framework analyses for helicopters and
UAV quadrotors.
Abstract: The objective of this study was to identify the optimal
level of partial replacement of Portland cement by the ashes
originating from burning straw and bagasse from sugar cane (ASB).
Order to this end, were made five series of flat plates and cylindrical
bodies: control and others with the partial replacement in 20, 30, 40
and 50% of ASB in relation to the mass of the Ordinary Portland
cement, and conducted a mechanical testing of simple axial
compression (cylindrical bodies) and the four-point bending (flat
plates) and determined water absorption (WA), bulk density (BD)
and apparent void volume (AVV) on both types of specimens. Based
on the data obtained, it may be noted that the control treatment
containing only Portland cement, obtained the best results. However,
the cylindrical bodies with 20% ashes showed better results
compared to the other treatments. And in the formulations plates, the
treatment which showed the best results was 30% cement
replacement by ashes.
Abstract: Estimation of model parameters is necessary to predict
the behavior of a system. Model parameters are estimated using
optimization criteria. Most algorithms use historical data to estimate
model parameters. The known target values (actual) and the output
produced by the model are compared. The differences between the
two form the basis to estimate the parameters. In order to compare
different models developed using the same data different criteria are
used. The data obtained for short scale projects are used here. We
consider software effort estimation problem using radial basis
function network. The accuracy comparison is made using various
existing criteria for one and two predictors. Then, we propose a new
criterion based on linear least squares for evaluation and compared
the results of one and two predictors. We have considered another
data set and evaluated prediction accuracy using the new criterion.
The new criterion is easy to comprehend compared to single statistic.
Although software effort estimation is considered, this method is
applicable for any modeling and prediction.
Abstract: Biofuels production has come forth as a future
technology to combat the problem of depleting fossil fuels. Bio-based
ethanol production from enzymatic lignocellulosic biomass
degradation serves an efficient method and catching the eye of
scientific community. High cost of the enzyme is the major obstacle
in preventing the commercialization of this process. Thus main
objective of the present study was to optimize composition of
medium components for enhancing cellulase production by newly
isolated strain of Bacillus tequilensis. Nineteen factors were taken
into account using statistical Plackett-Burman Design. The significant
variables influencing the cellulose production were further employed
in statistical Response Surface Methodology using Central
Composite Design for maximizing cellulase production. The
optimum medium composition for cellulase production was: peptone
(4.94 g/L), ammonium chloride (4.99 g/L), yeast extract (2.00 g/L),
Tween-20 (0.53 g/L), calcium chloride (0.20 g/L) and cobalt chloride
(0.60 g/L) with pH 7, agitation speed 150 rpm and 72 h incubation at
37oC. Analysis of variance (ANOVA) revealed high coefficient of
determination (R2) of 0.99. Maximum cellulase productivity of 11.5
IU/ml was observed against the model predicted value of 13 IU/ml.
This was found to be optimally active at 60oC and pH 5.5.