Abstract: Pneumatic reactors have been widely employed in various sectors of the chemical industry, especially where are required high heat and mass transfer rates. This study aimed to obtain correlations that allow the prediction of gas hold-up (Ԑ) and volumetric oxygen transfer coefficient (kLa), and compare these values, for three models of pneumatic reactors on two scales utilizing Newtonian fluids. Values of kLa were obtained using the dynamic pressure-step method, while e was used for a new proposed measure. Comparing the three models of reactors studied, it was observed that the mass transfer was superior to draft-tube airlift, reaching e of 0.173 and kLa of 0.00904s-1. All correlations showed good fit to the experimental data (R2≥94%), and comparisons with correlations from the literature demonstrate the need for further similar studies due to shortage of data available, mainly for airlift reactors and high viscosity fluids.
Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.
Abstract: This paper examines the system protection for cyber-physical
systems (CPS). CPS are particularly characterized by their
networking system components. This means they are able to adapt to
the needs of their users and its environment. With this ability, CPS
have new, specific requirements on the protection against anti-counterfeiting,
know-how loss and manipulation. They increase the
requirements on system protection because piracy attacks can be
more diverse, for example because of an increasing number of
interfaces or through the networking abilities. The new requirements
were identified and in a next step matched with existing protective
measures. Due to the found gap the development of new protection
measures has to be forced to close this gap. Moreover a comparison
of the effectiveness between selected measures was realized and the
first results are presented in this paper.
Abstract: This paper presents the results of an experimental
study undertaken to evaluate the local bond stress-slip response of
short embedment of reinforcing bars in normal concrete (NC) and
high performance fiber reinforced cement composites (HPFRCC)
blocks. Long embedment was investigated as well to gain insights on
the distribution of strain, slip, bar stress and bond stress along the bar
especially in post-yield range. A total of 12 specimens were tested,
by means of pull-out of the reinforcing bars from concrete blocks. It
was found that the enhancement of local bond strength can be
reached up to 50% and ductility of the bond behavior was improved
significantly if HPFRCC is used. Also, under a constant strain at
loaded end, HPFRCC has delayed yielding of bars at other location
from the loaded end. Hence, the reduction of bond stress was slower
for HPFRCC in comparison with NC. Due to the same reason, the
total slips at loaded end for HPFRCC was smaller than NC as
expected. Test results indicated that HPFRCC has better bond slip
behavior which makes it a suitable material to be employed in
anchorage zone such as beam-column joints.
Abstract: In this paper, a new concept of closed-loop design for a
product is presented. The closed-loop design model is developed by
integrating forward design and reverse design. Based on this new
concept, a closed-loop design model for sustainable manufacturing by
integrated evaluation of forward design, reverse design, and green
manufacturing using a fuzzy analytic network process is developed. In
the design stage of a product, with a given product requirement and
objective, there can be different ways to design the detailed
components and specifications. Therefore, there can be different
design cases to achieve the same product requirement and objective.
Subsequently, in the design evaluation stage, it is required to analyze
and evaluate the different design cases. The purpose of this research is
to develop a model for evaluating the design cases by integrated
evaluating the criteria in forward design, reverse design, and green
manufacturing. A fuzzy analytic network process method is presented
for integrated evaluation of the criteria in the three models. The
comparison matrices for evaluating the criteria in the three groups are
established. The total relational values among the three groups
represent the total relational effects. In applications, a super matrix
model is created and the total relational values can be used to evaluate
the design cases for decision-making to select the final design case. An
example product is demonstrated in this presentation. It shows that the
model is useful for integrated evaluation of forward design, reverse
design, and green manufacturing to achieve a closed-loop design for
sustainable manufacturing objective.
Abstract: Some plants of genus Schinus have been used in the
folk medicine as topical antiseptic, digestive, purgative, diuretic,
analgesic or antidepressant, and also for respiratory and urinary
infections. Chemical composition of essential oils of S. molle and S.
terebinthifolius had been evaluated and presented high variability
according with the part of the plant studied and with the geographic
and climatic regions. The pharmacological properties, namely
antimicrobial, anti-tumoural and anti-inflammatory activities are
conditioned by chemical composition of essential oils. Taking into
account the difficulty to infer the pharmacological properties of
Schinus essential oils without hard experimental approach, this work
will focus on the development of a decision support system, in terms
of its knowledge representation and reasoning procedures, under a
formal framework based on Logic Programming, complemented with
an approach to computing centered on Artificial Neural Networks
and the respective Degree-of-Confidence that one has on such an
occurrence.
Abstract: The objective of this study is to conduct computational
fluid dynamic (CFD) simulations for evaluating the cooling efficacy
from vegetation implanted in a public park in the Taipei, Taiwan. To
probe the impacts of park renewal by means of adding three pavilions
and supplementary green areas on urban microclimates, the simulated
results have revealed that the park having a higher percentage of green
coverage ratio (GCR) tended to experience a better cooling effect.
These findings can be used to explore the effects of different greening
modifications on urban environments for achieving an effective
thermal comfort in urban public spaces.
Abstract: In this study, one of the tools of Islamic financing
known as “Sukuk” a non-interest bearing investment which has
started to be implemented in Turkey and the world as a whole is
discussed. In order to increase the vitality and efficiency of the
economy, by taking lessons from the recent economic crisis new
developments in the banking and investment sector are being
expanded. The purpose of all investors is to obtain more revenue
through the use of capital. The inability of traditional investment
tools to meet the expectations of investors and the interest based
financial system where one investor benefits at the expense of
another there has been the need for a different, reliable and noninterest
bearing financial market that is consistent with the Islamic
rule. As a result an alternative and more reliable interest free
financing tool “Sukuk” rental certificates covering people who are
sensitive to Islamic rules, appeal to all segments, hidden remaining
capital that contributes to the economy, reduce disparities in income
distribution, common risk sharing system of profit and loss sharing
has emerged. Today, for the structural countries by examining the
state of the world market economy the applicability, enactment and
future issues associated with this attractive kind of Islamic finance
namely the “Sukuk” market has been explained.
Abstract: The rationale behind this study is considering
combating and preventing the phenomenon of trafficking in human
beings from a multidisciplinary perspective that involves many layers
of the society.
Trafficking in human beings is an abhorrent phenomenon highly
affecting negatively the victims and their families in both human and
material aspect, sometimes causing irreversible damages. The longer
term effects of this phenomenon, in countries with a weak economic
development and extremely young and dynamic population, such as
Kosovo, without proper measures to prevented and control can cause
tremendous damages in the society. Given the fact that a complete
eradication of this phenomenon is almost impossible, efforts should
be concentrated at least on the prevention and controlling aspects.
Treating trafficking in human beings based on traditional police
tactics, methods and proceedings cannot bring satisfactory results.
There is no doubt that a multi-disciplinary approach is an
irreplaceable requirement, in other words, a combination of authentic
and functional proactive and reactive methods, techniques and tactics.
Obviously, police must exercise its role in preventing and combating
trafficking in human beings, a role sanctioned by the law, however,
police role and contribution cannot by any means considered
complete if all segments of the society are not included in these
efforts. Naturally, civil society should have an important share in
these collaborative and interactive efforts especially in preventive
activities such as: awareness on trafficking risks and damages,
proactive engagement in drafting appropriate legislation and
strategies, law enforcement monitoring and direct or indirect
involvement in protective and supporting activities which benefit the
victims of trafficking etc.
Abstract: This paper addresses the design of hospital Intensive
Care Unit windows for the achievement of visual comfort and energy
savings. The aim was to identify the window size and shading system
configurations that could fulfill daylighting adequacy, avoid glare
and reduce energy consumption. The study focused on addressing the
effect of utilizing different shading systems in association with a
range of Window-to-Wall Ratios (WWR) in different orientations
under the desert clear-sky of Cairo, Egypt.
The results of this study demonstrated that solar penetration is a
critical concern affecting the design of ICU windows in desert
locations, as in Cairo, Egypt. Use of shading systems was found to be
essential in providing acceptable daylight performance and energy
saving. Careful positioning of the ICU window towards a proper
orientation can dramatically improve performance. It was observed
that ICU windows facing the north direction enjoyed the widest range
of successful window configuration possibilities at different WWRs.
ICU windows facing south enjoyed a reasonable number of
configuration options as well. By contrast, the ICU windows facing
the east orientation had a very limited number of options that provide
acceptable performance. These require additional local shading
measures at certain times due to glare incidence. Moreover, use of
horizontal sun breakers and solar screens to protect the ICU windows
proved to be more successful than the other alternatives in a wide
range of Window to Wall Ratios. By contrast, the use of light shelves
and vertical shading devices seemed questionable.
Abstract: Electrodeposition is a simple and economic technique
for precision coating of different shaped substrates with pure metal,
alloy or composite films. Dc electrodeposition was used to produce
Cr, Co-Cr and Co-Cr/TiO2 nano-composite coatings from Cr(III)
based electrolytes onto 316L SS substrates. The effects of TiO2 nanoparticles
concentration on co-deposition of these particles along with
Cr content and microhardness of the coatings were investigated.
Morphology of the Cr, Co-Cr and Co-Cr/TiO2 coatings besides their
tribological behavior were studied. The results showed that increment
of TiO2 nanoparticles concentration from 0 to 30 g L-1 in the bath
increased their co-deposition and Cr content of the coatings from 0 to
3.5 wt.% and from 23.7 to 31.2 wt.%, respectively. Microhardness of
Cr coating was about 920 Hv which was higher than Co-Cr and even
Co-Cr/TiO2 films. Microhardness of Co-Cr and Co-Cr/TiO2 coatings
were improved by increasing their Cr and TiO2 content. All the
coatings had nodular morphology and contained microcracks.
Nodules sizes and the number of microcracks in the alloy and
composite coatings were lower than the Cr film. Wear results
revealed that the Co-Cr/TiO2 coating had the lowest wear loss
between all the samples, while the Cr film had the worst wear
resistance.
Abstract: The comprehensive CFD models have been used to
represent and study the heterogeneous combustion of biomass. In the
present work, the operation of a global flue gas circuit in the sugarcane
bagasse combustion, from wind boxes below primary air grate
supply, passing by bagasse insertion in swirl burners and boiler
furnace, to boiler bank outlet is simulated. It uses five different
meshes representing each part of this system located in sequence:
wind boxes and grate, boiler furnace, swirl burners, superheaters and
boiler bank. The model considers turbulence using standard k-ε,
combustion using EDM, radiation heat transfer using DTM with 16
ray directions and bagasse particle tracking represented by Schiller-
Naumann model. The results showed good agreement with expected
behavior found in literature and equipment design. The more detailed
results view in separated parts of flue gas system allows observing
some flow behaviors that cannot be represented by usual
simplifications like bagasse supply under homogeneous axial and
rotational vectors and others that can be represented using new
considerations like the representation of 26 thousand grate orifices by
144 rectangular inlets.
Abstract: This article is to introduce the meaning and form of
social quality moving process as indicated by members of two suburb
communities with different social and cultural contexts. The form of
social quality moving process is very significant for the community
and social development, because it will make the people living
together with sustainable happiness.
This is a qualitative study involving 30 key-informants from two
suburb communities. Data were collected though key-informant
interviews, and analyzed using logical content description and
descriptive statistics.
This research found that on the social quality component, the
people in both communities stressed the procedure for social qualitymaking.
This includes the generousness, sharing and assisting among
people in the communities. These practices helped making people to
live together with sustainable happiness. Living as a family or appear
to be a family is the major social characteristic of these two
communities.
This research also found that form of social quality’s moving
process of both communities stress relation of human and nature;
“nature overpower humans” paradigm and influence of religious
doctrine that emphasizes relations among humans. Both criteria make
the form of social’s moving process simple, adaptive to nature and
caring for opinion sharing and understanding among each other
before action. This form of social quality’s moving process is
composed of 4 steps; (1) awareness building, (2) motivation to
change, (3) participation from every party which is concerned (4)
self-reliance.
Abstract: The fatigue life of tubular joints commonly found in
offshore industry is not only dependent on the value of hot-spot stress
(HSS), but is also significantly influenced by the through-thethickness
stress distribution characterized by the degree of bending
(DoB). The determination of DoB values in a tubular joint is essential
for improving the accuracy of fatigue life estimation using the stresslife
(S–N) method and particularly for predicting the fatigue crack
growth based on the fracture mechanics (FM) approach. In the
present paper, data extracted from finite element (FE) analyses of
tubular KT-joints, verified against experimental data and parametric
equations, was used to investigate the effects of geometrical
parameters on DoB values at the crown 0°, saddle, and crown 180°
positions along the weld toe of central brace in tubular KT-joints
subjected to axial loading. Parametric study was followed by a set of
nonlinear regression analyses to derive DoB parametric formulas for
the fatigue analysis of KT-joints under axial loads. The tubular KTjoint
is a quite common joint type found in steel offshore structures.
However, despite the crucial role of the DoB in evaluating the fatigue
performance of tubular joints, this paper is the first attempt to study
and formulate the DoB values in KT-joints.
Abstract: Water miscible cutting fluids are conventionally used to lubricate and cool the machining zone. But issues related to health hazards, maintenance and disposal costs have limited their usage, leading to application of Minimum Quantity Lubrication (MQL). To increase the effectiveness of MQL, nanocutting fluids are proposed. In the present work, water miscible nanographite cutting fluids of varying concentration are applied at cutting zone by two systems A and B. System A utilizes high pressure air and supplies cutting fluid at a flow rate of 1ml/min. System B uses low pressure air and supplies cutting fluid at a flow rate of 5ml/min. Their performance in machining is evaluated by measuring cutting temperatures, tool wear, cutting forces and surface roughness and compared with dry machining and flood machining. Application of nanocutting fluid using both systems showed better performance than dry machining. Cutting temperatures and cutting forces obtained by both techniques are more than flood machining. But tool wear and surface roughness showed improvement compared to flood machining. Economic analysis has been carried out in all the cases to decide the applicability of the techniques.
Abstract: Damage status of RC buildings is greatly influenced
by the characteristics of the imposed ground motion. Peak Ground
Acceleration and frequency contents are considered the main two
factors that affect ground motion characteristics; hence, affecting the
seismic response of RC structures and consequently their damage
state. A detailed investigation on the combined effects of these two
factors on damage assessment of RC buildings is carried out. Twenty
one earthquake records are analyzed and arranged into three groups,
according to their frequency contents. These records are used in an
investigation to define the expected damage state that would be
attained by RC buildings, if subjected to varying ground motion
characteristics. The damage assessment is conducted through
examining drift ratios and damage indices of the overall structure and
the significant structural components of RC building. Base and story
shear of RC building model, are also investigated, for cases when the
model is subjected to the chosen twenty one earthquake records.
Nonlinear dynamic analyses are performed on a 2-dimensional model
of a 12-story RC building.
Abstract: The main purpose of this study was to figure out
employees’ attitudes toward the new performance appraisal program
and to examine whether three different types of appraisal processes
differentially affected job satisfaction and employee engagement. The
second purpose of this study was to investigate the relationship
between performance appraisal reform, job satisfaction, and employee
engagement. A large polyester and textile corporation had 2046
non-operational employees in February 2014. The valid participants
were 1474 (72.04%) in this study. Data analysis included descriptive
statistics, one-way ANOVA, one-way MANOVA, Pearson correlation,
Content Validity Index, the exploratory factor analysis, and reliability
analysis. The general results showed that employees who received the
new performance appraisal program evaluated the program more
positively and showed more job satisfaction than those who did not. In
particular, the implementation effects of this new performance
appraisal program were most highly rated by employees who used the
KPI to rate their job performance. Moreover, employees’ attitudes
toward the new performance appraisal program were positively related
to their job satisfaction and employee engagement. Lastly, most
employees regarded themselves as engaged workers. To sum up, the
HR department of this company has made an effective contribution to
performance appraisal reforms.
Abstract: Auditory hallucinations among the most invalidating
and distressing experiences reported by patients diagnosed with
schizophrenia, leading to feelings of powerlessness and helplessness
towards their illness. In more severe cases, these auditory
hallucinations can take the form of commanding voices, which are
often related to high suicidality rates in these patients. Several
authors propose that the meanings attributed to the hallucinatory
experience, rather than characteristics like form and content, can be
determinant in patients’ reactions to hallucinatory activity,
particularly in the case of voice-hearing experiences. In this study, 48
patients diagnosed with paranoid schizophrenia presenting auditory
hallucinations were studied. Multiple regression analyses were
computed to study the influence of several developmental aspects,
such as family and social dynamics, bullying, depression, and sociocognitive
variables on the auditory hallucinations, on patients’
attributions and relationships with their voices, and on the resulting
invalidation of hallucinatory experience. Overall, results showed how
relationships with voices can mirror several aspects of interpersonal
relationship with others, and how self-schemas, depression and actual
social relationships help shaping the voice-hearing experience. Early
experiences of victimization and submission help predict the
attributions of omnipotence of the voices, and increased hostility
from parents seems to increase the malevolence of the voices,
suggesting that socio-cognitive factors can significantly contribute to
the etiology and maintenance of auditory hallucinations. The
understanding of the characteristics of auditory hallucinations and the
relationships patients established with their voices can allow the
development of more promising therapeutic interventions that can be
more effective in decreasing invalidation caused by this devastating
mental illness.
Abstract: Image Processing is a structure of Signal Processing
for which the input is the image and the output is also an image or
parameter of the image. Image Resolution has been frequently
referred as an important aspect of an image. In Image Resolution
Enhancement, images are being processed in order to obtain more
enhanced resolution. To generate highly resoluted image for a low
resoluted input image with high PSNR value. Stationary Wavelet
Transform is used for Edge Detection and minimize the loss occurs
during Downsampling. Inverse Discrete Wavelet Transform is to get
highly resoluted image. Highly resoluted output is generated from the
Low resolution input with high quality. Noisy input will generate
output with low PSNR value. So Noisy resolution enhancement
technique has been used for adaptive sub-band thresholding is used.
Downsampling in each of the DWT subbands causes information loss
in the respective subbands. SWT is employed to minimize this loss.
Inverse Discrete wavelet transform (IDWT) is to convert the object
which is downsampled using DWT into a highly resoluted object.
Used Image denoising and resolution enhancement techniques will
generate image with high PSNR value. Our Proposed method will
improve Image Resolution and reached the optimized threshold.
Abstract: Cerebellar ataxia is a steadily progressive
neurodegenerative disease associated with loss of motor control,
leaving patients unable to walk, talk, or perform activities of daily
living. Direct motor instruction in cerebella ataxia patients has limited
effectiveness, presumably because an inappropriate closed-loop
cerebellar response to the inevitable observed error confounds motor
learning mechanisms. Could the use of EEG based BCI provide
advanced biofeedback to improve motor imagery and provide a
“backdoor” to improving motor performance in ataxia patients? In
order to determine the feasibility of using EEG-based BCI control in
this population, we compare the ability to modulate mu-band power
(8-12 Hz) by performing a cued motor imagery task in an ataxia
patient and healthy control.