Abstract: A capacity spectrum method (CSM), one of methodologies to evaluate seismic fragilities of building structures, has been long recognized as the most convenient method, even if it contains several limitations to predict the seismic response of structures of interest. This paper proposes the procedure to estimate seismic fragility curves using an incremental dynamic analysis (IDA) rather than the method adopting a CSM. To achieve the research purpose, this study compares the seismic fragility curves of a 5-story reinforced concrete (RC) moment frame obtained from both methods; an IDA method and aCSM. Both seismic fragility curves are similar in slight and moderate damage states whereas the fragility curve obtained from the IDA method presents less variation (or uncertainties) in extensive and complete damage states. This is due to the fact that the IDA method can properly capture the structural response beyond yielding rather than the CSM and can directly calculate higher mode effects. From these observations, the CSM could overestimate seismic vulnerabilities of the studied structure in extensive or complete damage states.
Abstract: For cycling, the analysis of the pedal force is one of the
important factors in the study of exercise ability assessment and
overuse injuries. In past studies, a two-axis measurement sensor was
used at the sagittal plane to measure the force only in the anterior,
posterior, and vertical directions and to analyze the loss of force and
the injury on the frontal plane due to the forces in the right and left
directions. In this study, which is a basic study on diverse analyses of
the pedal force that consider the forces on the sagittal plane and the
frontal plane, a three-axis pedal force measurement sensor was
developed to measure the anterior-posterior (Fx), medio-lateral (Fz),
and vertical (Fy) forces. The sensor was fabricated with a size and
shape similar to those of the general flat pedal, and had a 550g weight
that allowed smooth pedaling. Its measurement range was ±1000 N for
Fx and Fz and ±2000 N for Fy, and its non-linearity, hysteresis, and
repeatability were approximately 0.5%. The data were sampled at
1000 Hz using a signal collector. To use the developed sensor, the
pedaling efficiency (index of efficiency, IE) and the range of left and
right (medio-lateral, ML) forces were measured with two seat heights
(low and high). The results of the measurement showed that the IE was
higher and the force range in the ML direction was lower with the high
position than with the low position. The developed measurement
sensor and its application results will be useful in understanding and
explaining the complicated pedaling technique, and will enable
diverse kinematic analyses of the pedal force on the sagittal plane and
the frontal plane.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: It is widely believed that mobile device is a promising technology for lending the opportunity for the third wave of electronic commerce. Mobile devices have changed the way companies do business. Many applications are under development or being incorporated into business processes. In this day, mobile applications are a vital component of any industry strategy.One of the greatest benefits of selling merchandise and providing services on a mobile application is that it widens a company’s customer base significantly.Mobile applications are accessible to interested customers across regional and international borders in different electronic business (e-business) area. But there is a dark side to this success story. The security risks associated with mobile devices and applications are very significant. This paper introduces a broad risk analysis for the various threats, vulnerabilities, and risks in mobile e-business applications and presents some important risk mitigation approaches. It reviews and compares two different frameworks for security assurance in mobile e-business applications. Based on the comparison, the paper suggests some recommendations for applications developers and business owners in mobile e-business application development process.
Abstract: The present study was carried out to evaluate the
effect of different levels of dietary seed and extract of Harmal
(Peganum harmala L.) on immunity of broiler chicks. A total of 350
one-day old broiler chicks (Ross 308) were randomly allocated to
five dietary treatments with four replicates pen of 14 birds each.
Dietary treatments consisted of control, 1 and 2 g/kg Harmal seed in
diet, 100 and 200 mg/L Harmal seed extract in water. Broilers
received dietary treatments from 1 to 42 d. Two birds from each pen
were randomly weighed and sacrificed at 42 d of age, the relative
weight of lymphoid organs (bursa of Fabercius and spleen) to live
weight were calculated. Antibody titers against Newcastle and
influenza viruses and sheep red blood cell were measured at 30 d of
age. Results showed that the relative weights of lymphoid organs
were not affected by dietary treatments. Furthermore, antibody titer
against Newcastle and influenza viruses as well as sheep red blood
cell antigen were significantly (P
Abstract: Chemical Reaction Optimization (CRO) is an
optimization metaheuristic inspired by the nature of chemical
reactions as a natural process of transforming the substances from
unstable to stable states. Starting with some unstable molecules with
excessive energy, a sequence of interactions takes the set to a state of
minimum energy. Researchers reported successful application of the
algorithm in solving some engineering problems, like the quadratic
assignment problem, with superior performance when compared with
other optimization algorithms. We adapted this optimization
algorithm to the Printed Circuit Board Drilling Problem (PCBDP)
towards reducing the drilling time and hence improving the PCB
manufacturing throughput. Although the PCBDP can be viewed as
instance of the popular Traveling Salesman Problem (TSP), it has
some characteristics that would require special attention to the
transactions that explore the solution landscape. Experimental test
results using the standard CROToolBox are not promising for
practically sized problems, while it could find optimal solutions for
artificial problems and small benchmarks as a proof of concept.
Abstract: Batteries of electric vehicles (BEV) are becoming
more attractive with the advancement of new battery technologies
and promotion of electric vehicles. BEV batteries are recharged on
board vehicles using either the grid (G2V for Grid to Vehicle) or
renewable energies in a stand-alone application (H2V for Home to
Vehicle). This paper deals with the modeling, sizing and control of a
photovoltaic stand-alone application that can charge the BEV at
home. The modeling approach and developed mathematical models
describing the system components are detailed. Simulation and
experimental results are presented and commented.
Abstract: In this study a ternary system containing sodium
chloride as solute, water as primary solvent and ethanol as the
antisolvent was considered to investigate the application of artificial
neural network (ANN) in prediction of sodium solubility in the
mixture of water as the solvent and ethanol as the antisolvent. The
system was previously studied using by Extended UNIQUAC model
by the authors of this study. The comparison between the results of
the two models shows an excellent agreement between them
(R2=0.99), and also approves the capability of ANN to predict the
thermodynamic behavior of ternary electrolyte systems which are
difficult to model.
Abstract: To date, one of the few comprehensive indicators for
the measurement of food security is the Global Food Security Index
(GFSI). This index is a dynamic quantitative and qualitative
benchmarking model, constructed from 28 unique indicators, that
measures drivers of food security across both developing and
developed countries. Whereas the GFSI has been calculated across a
set of 109 countries, in this paper we aim to present and compare, for
the Middle East and North Africa (MENA), 1) the Food Security
Index scores achieved and 2) the data available on affordability,
availability, and quality of food. The data for this work was taken
from the latest available report published by the creators of the GFSI,
which in turn used information from national and international
statistical sources. MENA countries rank from place 17/109 (Israel,
although with resent political turmoil this is likely to have changed)
to place 91/109 (Yemen) with household expenditure spent in food
ranging from 15.5% (Israel) to 60% (Egypt). Lower spending on food
as a share of household consumption in most countries and better
food safety net programs in the MENA have contributed to a notable
increase in food affordability. The region has also, however,
experienced a decline in food availability, owing to more limited
food supplies and higher volatility of agricultural production. In
terms of food quality and safety the MENA has the top ranking
country (Israel). The most frequent challenges faced by the countries
of the MENA include public expenditure on agricultural research and
development as well as volatility of agricultural production. Food
security is a complex phenomenon that interacts with many other
indicators of a country’s wellbeing; in the MENA it is slowly but
markedly improving.
Abstract: This paper presents analysis and design of a wideband
Wilkinson power divider for wireless applications. The design is
accomplished by transforming the lengths and impedances of the
quarter wavelength sections of the conventional Wilkinson power
divider into U-shaped sections. The designed power divider is
simulated by using ADS Agilent technologies and CST microwave
studio software. It is shown that the proposed power divider has
simple topology and good performances in terms of insertion loss,
port matching and isolation at all operating frequencies (1.8 GHz,
2.45 GHz and 3.55 GHz).
Abstract: Lightweight design represents an important key to
successful implementation of energy-saving, fuel-efficient and
environmentally friendly means of transport in the aerospace and
automotive industry. In this context the use of carbon fibre reinforced
plastics (CFRP) which are distinguished by their outstanding
mechanical properties at relatively low weight, promise significant
improvements. Due to the reduction of the total mass, with the
resulting lowered fuel or energy consumption and CO2 emissions
during the operational phase, commercial aircraft will increasingly be
made of CFRP. An auspicious technology for the efficient and
economic production of high performance thermoset composites and
hybrid structures for future lightweight applications is the
combination of carbon fibre sheet moulding compound, tailored
continuous carbon fibre reinforcements and metallic components in a
one-shot pressing and curing process. This paper deals with a hybrid
composite technology for aerospace industries, which was developed
with the help of a special innovation and development system.
Abstract: This paper investigates the activity of the rectus
femoris (RF) and biceps femoris (BF) in healthy subjects during salat
(prostration) and specific exercise (squat exercise) using
electromyography (EMG). A group of undergraduates aged between
19 to 25 years voluntarily participated in this study. The myoelectric
activity of the muscles were recorded and analyzed. The finding
indicated that there were contractions of the muscles during the salat
and exercise with almost same EMG’s level. From the result,
Wilcoxon’s Rank Sum test showed significant difference between
prostration and squat exercise (p
Abstract: This paper presents the development of a single-ended 38.5 kS/s 10-bit programmable reference SAR ADC which is realized in MIMOS’s 0.35 µm CMOS process. The design uses a resistive DAC, a dynamic comparator with pre-amplifier and a SAR digital logic to create 10 effective bits ADC. A programmable reference circuitry allows the ADC to operate with different input range from 0.6 V to 2.1 V. The ADC consumed less than 7.5 mW power with a 3 V supply.
Abstract: A thermosyphon system is a heat transfer loop which
operates on the basis of gravity and buoyancy forces. It guarantees a
good reliability and low maintenance cost as it does not involve any
mechanical pump. Therefore, it can be used in many industrial
applications such as refrigeration and air conditioning, electronic
cooling, nuclear reactors, geothermal heat extraction, etc. But flow
instabilities and loop configuration are the major problems in this
system. Several previous researchers studied that stabilities can be
suppressed by using nanofluids as loop fluid. In the present study a
rectangular thermosyphon loop with end heat exchangers are
considered for the study. This configuration is more appropriate for
many practical applications such as solar water heater, geothermal
heat extraction, etc. In the present work, steady-state analysis is
carried out on thermosyphon loop with parallel flow coaxial heat
exchangers at heat source and heat sink. In this loop nanofluid is
considered as the loop fluid and water is considered as the external
fluid in both hot and cold heat exchangers. For this analysis onedimensional
homogeneous model is developed. In this model,
conservation equations like conservation of mass, momentum, energy
are discretized using finite difference method. A computer code is
written in MATLAB to simulate the flow in thermosyphon loop. A
comparison in terms of heat transfer is made between water and
nanofluid as working fluids in the loop.
Abstract: Vertical Handover(VHO) among different
communication technologies ensuring uninterruption and service
continuity is one of the most important performance parameter in
Heterogenous networks environment. In an integrated Universal
Mobile Telecommunicatin System(UMTS) and Wireless Local
Area Network(WLAN), WLAN is given an inherent priority over
UMTS because of its high data rates with low cost. Therefore
mobile users want to be associated with WLAN maximum of the
time while roaming, to enjoy best possible services with low cost.
That encourages reduction of number of VHO. In this work the
reduction of number of VHO with respect to varying number of
WLAN Access Points(APs) in an integrated UMTS and WLAN
network is investigated through simulation to provide best possible
cost effective service to the users. The simulation has been carried
out for an area (7800 × 9006)m2 where COST-231 Hata model
and 3GPP (TR 101 112 V 3.1.0) specified models are used for
WLAN and UMTS path loss models respectively. The handover
decision is triggered based on the received signal level as compared
to the fade margin. Fade margin gives a probabilistic measure of
the reliability of the communication link. A relationship between
number of WLAN APs and the number of VHO is also established
in this work.
Abstract: The transition period of Kosovo society brought
fundamental changes in all the spheres of organizing life. This was
the period when also in the cultural tradition the biggest movement
and an emerging from ‘isolation’ or from the ‘shell’ occurred.
Transformation of the traditional and embracing of the modern began
here. The same was experienced and is currently being experienced
also by Gjakova and its surrounding which is historically renowned
for its great tradition and culture.
The population of this region is actually facing a transition from
the traditional system into the modern one and quite often with huge
leaps.
These ‘movements’ or ‘evolutions’ of the society of this region,
besides the numerous positive things it ‘harvested’, also brought
things that do not at all correspond with their tradition as well as new
criminal occurrences which in the past were not present in this area.
Furthermore, some of the ‘new’ behaviors that are embraced from
other ‘cultures’ and ‘civilizations’, and which are often exceeded, are
quite perturbing. The security situation is also worrying, particularly
following the appearance of some new criminal occurrences.
Therefore, with this research paper we will strive to analyze the
new cultural “intersections” as well as the nature of the origin of
some new very worrying criminal occurrences. We will present there
also some factors inciting into these occurrences, which were
confessed by the persons involved in these criminal occurrences and
who come from this very region.
Abstract: Fugitive particulate matter (PM) is a major source of
airborne pollution in the Middle East countries. The meteorological
conditions and topography of the area makes it highly susceptible to
wind-blown particles which raise many air quality concerns. Air
quality tools such as field monitoring, emission factors and dispersion
modeling have been used in previous research studies to analyze the
release and impacts of fugitive PM in the region. However, these
tools have been originally developed based on experiments made for
European and North American regions. In this work, an experimental
campaign was conducted on April-May 2014 in a construction site in
Doha city, Qatar. The ultimate goal is to evaluate the applicability of
the existing emission factors for construction sites in dry and arid
areas like the Middle East.
Abstract: We present a solution to the Maxmin u/E parameters
estimation problem of possibility distributions in m-dimensional
case. Our method is based on geometrical approach, where minimal
area enclosing ellipsoid is constructed around the sample. Also we
demonstrate that one can improve results of well-known algorithms
in fuzzy model identification task using Maxmin u/E parameters
estimation.
Abstract: Welfare may be considered to be a subjective
experience; it has a biological function that is related to the fitness
and survival of the animal accordingly, researches have suggested
that welfare is compromised when the animal's evolutionary fitness is
reduced. This study was carried out to explain the effect of some
managerial stressors as handling and restraint on behavioral patterns
and biochemical parameters of rats. A total of 24 (12 males & 12
females) Sprague-Dawley rats (12 months & 150-180g) were allotted
into 3 groups, handled group (4 male & 4 female), restrained group (4
male & 4 female) and control group (4 males & 4 females).
The obtained results revealed that time spent feeding, drinking,
movement and cage exploration frequencies increased significantly in
handled rats than other groups, while lying time and licking increased
significantly in restrained rats than handled and controls. Moreover,
social behavior decreased in both stressed groups than control.
Triglycerides were significantly increased in handled rats than
other groups, while total lipid, total protein and globulin significantly
increased in both treated groups than control. Corticosterone
increased in restrained and handled rats than control ones. Moreover,
there was an increment in packed cell volume significantly in
restrained rats than others. These deducted that if we want to study
the effect of stress on animal welfare it is necessary to study the
effect of such stressors on animal’s behavior and physiological
responses.
Abstract: This paper focuses on the assessment of the air
pollution and morbidity relationship in Tunisia. Air pollution is
measured by ozone air concentration and the morbidity is measured
by the number of respiratory-related restricted activity days during
the 2-week period prior to the interview. Socioeconomic data are also
collected in order to adjust for any confounding covariates. Our
sample is composed by 407 Tunisian respondents; 44.7% are women,
the average age is 35.2, near 69% are living in a house built after
1980, and 27.8% have reported at least one day of respiratory-related
restricted activity. The model consists on the regression of the
number of respiratory-related restricted activity days on the air
quality measure and the socioeconomic covariates. In order to correct
for zero-inflation and heterogeneity, we estimate several models
(Poisson, negative binomial, zero inflated Poisson, Poisson hurdle,
negative binomial hurdle and finite mixture Poisson models).
Bootstrapping and post-stratification techniques are used in order to
correct for any sample bias. According to the Akaike information
criteria, the hurdle negative binomial model has the greatest goodness
of fit. The main result indicates that, after adjusting for
socioeconomic data, the ozone concentration increases the probability
of positive number of restricted activity days.