Abstract: Three sulphonic acid-doped polyanilines were
synthesized through chemical oxidation at low temperature (0-5 oC)
and potential of these polymers as sensing agent for O2 gas detection
in terms of fluorescence quenching was studied. Sulphuric acid,
dodecylbenzene sulphonic acid (DBSA) and camphor sulphonic acid
(CSA) were used as doping agents. All polymers obtained were dark
green powder. Polymers obtained were characterized by Fourier
transform infrared spectroscopy, ultraviolet-visible absorption
spectroscopy, thermogravimetry analysis, elemental analysis,
differential scanning calorimeter and gel permeation
chromatography. Characterizations carried out showed that polymers
were successfully synthesized with mass recovery for sulphuric aciddoped
polyaniline (SPAN), DBSA-doped polyaniline (DBSA-doped
PANI) and CSA-doped polyaniline (CSA-doped PANI) of 71.40%,
75.00% and 39.96%, respectively. Doping level of SPAN, DBSAdoped
PANI and CSA-doped PANI were 32.86%, 33.13% and
53.96%, respectively as determined based on elemental analysis.
Sensing test was carried out on polymer sample in the form of
solution and film by using fluorescence spectrophotometer. Samples
of polymer solution and polymer film showed positive response
towards O2 exposure. All polymer solutions and films were fully
regenerated by using N2 gas within 1 hour period. Photostability
study showed that all samples of polymer solutions and films were
stable towards light when continuously exposed to xenon lamp for 9
hours. The relative standard deviation (RSD) values for SPAN
solution, DBSA-doped PANI solution and CSA-doped PANI
solution for repeatability were 0.23%, 0.64% and 0.76%,
respectively. Meanwhile RSD values for reproducibility were 2.36%,
6.98% and 1.27%, respectively. Results for SPAN film, DBSAdoped
PANI film and CSA-doped PANI film showed the same
pattern with RSD values for repeatability of 0.52%, 4.05% and
0.90%, respectively. Meanwhile RSD values for reproducibility were
2.91%, 10.05% and 7.42%, respectively. The study on effect of the
flow rate on response time was carried out using 3 different rates
which were 0.25 mL/s, 1.00 mL/s and 2.00 mL/s. Results obtained
showed that the higher the flow rate, the shorter the response time.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: For smaller mechatronic device, especially for micro
Electronic system, a micro machining is a must. However, most
investigations on vibration of a mill have been limited to the
traditional type mill. In this article, vibration and dynamic
characteristics of a micro mill were investigated in this study. The
trend towards higher precision manufacturing technology requires
producing miniaturized components. To improve micro-milled
product quality, obtain a higher production rate and avoid milling
breakage, the dynamic characteristics of micro milling must be
studied. A stepped pre-twisted mill is used to simulate the micro mill.
The finite element analysis is employed in this work. The flute length
and diameter effects of the micro mill are considered. It is clear that
the effects of micro mill shape parameters on vibration in a micro mill
are significant.
Abstract: This work is focused on the steady boundary layer flow
near the forward stagnation point of plane and axisymmetric bodies
towards a stretching sheet. The no slip condition on the solid
boundary is replaced by the partial slip condition. The analytical
solutions for the velocity distributions are obtained for the various
values of the ratio of free stream velocity and stretching velocity, slip
parameter, the suction and injection velocity parameter, magnetic
parameter and dimensionality index parameter in the series forms with
the help of homotopy analysis method (HAM). Convergence of the
series is explicitly discussed. Results show that the flow and the skin
friction coefficient depend heavily on the velocity slip factor. In
addition, the effects of all the parameters mentioned above were more
pronounced for plane flows than for axisymmetric flows.
Abstract: Since the feasibility study of R&D programs have been
initiated for efficient public R&D investments, year 2008, feasibility
studies have improved in terms of precision. Although experience
related to these studies of R&D programs have increased to a certain
point, still methodological improvement is required. The feasibility
studies of R&D programs are consisted of various viewpoints, such as
technology, policy, and economics. This research is to provide
improvement methods to the economic perspective; especially the cost
estimation process of R&D activities. First of all, the fundamental
concept of cost estimation is reviewed. After the review, a statistical
and econometric analysis method is applied as empirical analysis.
Conclusively, limitations and further research directions are provided.
Abstract: Large scale climate signals and their teleconnections can influence hydro-meteorological variables on a local scale. Several extreme flow and timing measures, including high flow and low flow measures, from 62 hydrometric stations in Canada are investigated to detect possible linkages with several large scale climate indices. The streamflow data used in this study are derived from the Canadian Reference Hydrometric Basin Network and are characterized by relatively pristine and stable land-use conditions with a minimum of 40 years of record. A composite analysis approach was used to identify linkages between extreme flow and timing measures and climate indices. The approach involves determining the 10 highest and 10 lowest values of various climate indices from the data record. Extreme flow and timing measures for each station were examined for the years associated with the 10 largest values and the years associated with the 10 smallest values. In each case, a re-sampling approach was applied to determine if the 10 values of extreme flow measures differed significantly from the series mean. Results indicate that several stations are impacted by the large scale climate indices considered in this study. The results allow the determination of any relationship between stations that exhibit a statistically significant trend and stations for which the extreme measures exhibit a linkage with the climate indices.
Abstract: Internet infrastructures in most places of the world
have been supported by the advancement of optical fiber technology,
most notably wavelength division multiplexing (WDM) system.
Optical technology by means of WDM system has revolutionized
long distance data transport and has resulted in high data capacity,
cost reductions, extremely low bit error rate, and operational
simplification of the overall Internet infrastructure. This paper
analyses and compares the system impairments, which occur at data
transmission rates of 2.5Gb/s and 10 Gb/s per wavelength channel in
our proposed optical WDM system for Internet infrastructure in
Tanzania. The results show that the data transmission rate of 2.5 Gb/s
has minimum system impairments compared with a rate of 10 Gb/s
per wavelength channel, and achieves a sufficient system
performance to provide a good Internet access service.
Abstract: This study examined the role of driving experience in hazard perception and categorization using traffic scene pictures. Specifically, young-inexperienced, moderately experienced and very experienced (taxi) drivers observed traffic scene pictures while connected to an eye tracking system and were asked to rate the level of hazardousness of each picture and to mention the three most prominent hazards in it. Target pictures included nine, nearly identical, pairs of pictures where one picture in each pair included an actual hazard as an additional element. Altogether, 22 areas of interest (AOIs) were predefined and included 13 potential hazards and 9 actual hazards. Data analysis included both verbal reports and eye scanning patterns of these AOIs. Generally, both experienced and taxi drivers noted a relatively larger number of potential hazards than young inexperienced drivers Thus, by relating to less salient potential hazards, experienced drivers have demonstrated a better situation model of the traffic environment.
Abstract: A generalized method for small-signal simulation of
avalanche noise in Mixed Tunneling Avalanche Transit Time
(MITATT) device is presented in this paper where the effect of series
resistance is taken into account. The method is applied to a
millimeter-wave Double Drift Region (DDR) MITATT device based
on Silicon to obtain noise spectral density and noise measure as a
function of frequency for different values of series resistance. It is
found that noise measure of the device at the operating frequency
(122 GHz) with input power density of 1010 Watt/m2 is about 35 dB
for hypothetical parasitic series resistance of zero ohm (estimated
junction temperature = 500 K). Results show that the noise measure
increases as the value of parasitic resistance increases.
Abstract: The request for a sustainable development challenges
both managers and consumers to rethink habitual practices and
activities. While consumers are challenged to develop sustainable
consumption patterns, companies are asked to establish managerial
systems and structures considering economical, ecological, and social
issues. As this is in particular true for housing associations, this paper
aims first, at providing an understanding of sustainability strategy in
residential trade and industry (RTI) by identifying relevant facets of
this construct and second, at conceptually analyzing the impact of
sustainability strategy in RTI on operational efficiency and
performance of municipal housing companies. The author develops a
model of sustainability strategy in RTI and its effects and further,
sheds light in priorities for future research.
Abstract: The measurement of aerodynamic forces and moments
acting on an aircraft model is important for the development of wind
tunnel measurement technology to predict the performance of the full
scale vehicle. The potentials of an aircraft model with and without
winglet and aerodynamic characteristics with NACA wing No. 65-3-
218 have been studied using subsonic wind tunnel of 1 m × 1 m
rectangular test section and 2.5 m long of Aerodynamics Laboratory
Faculty of Engineering (University Putra Malaysia). Focusing on
analyzing the aerodynamic characteristics of the aircraft model, two
main issues are studied in this paper. First, a six component wind
tunnel external balance is used for measuring lift, drag and pitching
moment. Secondly, Tests are conducted on the aircraft model with
and without winglet of two configurations at Reynolds numbers
1.7×105, 2.1×105, and 2.5×105 for different angle of attacks. Fuzzy
logic approach is found as efficient for the representation,
manipulation and utilization of aerodynamic characteristics.
Therefore, the primary purpose of this work was to investigate the
relationship between lift and drag coefficients, with free-stream
velocities and angle of attacks, and to illustrate how fuzzy logic
might play an important role in study of lift aerodynamic
characteristics of an aircraft model with the addition of certain
winglet configurations. Results of the developed fuzzy logic were
compared with the experimental results. For lift coefficient analysis,
the mean of actual and predicted values were 0.62 and 0.60
respectively. The coreelation between actual and predicted values
(from FLS model) of lift coefficient in different angle of attack was
found as 0.99. The mean relative error of actual and predicted valus
was found as 5.18% for the velocity of 26.36 m/s which was found to
be less than the acceptable limits (10%). The goodness of fit of
prediction value was 0.95 which was close to 1.0.
Abstract: Historic religious buildings located in seismic areas
have developed different failure mechanisms. Simulation of failure
modes is done with computer programs through a nonlinear dynamic
analysis or simplified using the method of failure blocks. Currently
there are simulation methodologies of failure modes based on the
failure rigid blocks method only for Roman Catholic churches type.
Due to differences of shape in plan, elevation and construction
systems between Orthodox churches and Catholic churches, for the
first time there were initiated researches in the development of this
simulation methodology for Orthodox churches. In this article are
presented the first results from the researches. The theoretical results
were compared with real failure modes recorded at an Orthodox
church from Banat region, severely damaged by earthquakes in
1991. Simulated seismic response, using a computer program based
on finite element method was confirmed by cracks after earthquakes.
The consolidation of the church was made according to these
theoretical results, realizing a rigid floor connecting all the failure
blocks.
Abstract: This paper presents the experimental results of silicone rubber outdoor polymer insulators in salt fog ageing test based on IEC 61109. Specimens made ofHTV silicone rubber with ATH content having three different configurations, straight shedsalternated sheds, and incline and alternate sheds, were tested continuously 1000 hrs.in artificial salt fog chamber. Contamination level, reduction of hydrophobicity and hardness measurement were used as physical damaged inspection techniques to evaluate degree of surface deterioration. In addition, chemical changing of tested specimen surface was evaluated by ATR-FTIRto confirm physical damaged inspection. After 1000 hrs.of salt fog test, differences in degree of surface deterioration were observed on all tested specimens. Physical damaged inspection and chemical analysis results confirmed the experimental results as well.
Abstract: SDMA (Space-Division Multiple Access) is a MIMO
(Multiple-Input and Multiple-Output) based wireless communication
network architecture which has the potential to significantly increase
the spectral efficiency and the system performance. The maximum
likelihood (ML) detection provides the optimal performance, but its
complexity increases exponentially with the constellation size of
modulation and number of users. The QR decomposition (QRD)
MUD can be a substitute to ML detection due its low complexity and
near optimal performance. The minimum mean-squared-error
(MMSE) multiuser detection (MUD) minimises the mean square
error (MSE), which may not give guarantee that the BER of the
system is also minimum. But the minimum bit error rate (MBER)
MUD performs better than the classic MMSE MUD in term of
minimum probability of error by directly minimising the BER cost
function. Also the MBER MUD is able to support more users than
the number of receiving antennas, whereas the rest of MUDs fail in
this scenario. In this paper the performance of various MUD
techniques is verified for the correlated MIMO channel models based
on IEEE 802.16n standard.
Abstract: This paper studies the dependability of componentbased
applications, especially embedded ones, from the diagnosis
point of view. The principle of the diagnosis technique is to
implement inter-component tests in order to detect and locate the
faulty components without redundancy. The proposed approach for
diagnosing faulty components consists of two main aspects. The first
one concerns the execution of the inter-component tests which
requires integrating test functionality within a component. This is the
subject of this paper. The second one is the diagnosis process itself
which consists of the analysis of inter-component test results to
determine the fault-state of the whole system. Advantage of this
diagnosis method when compared to classical redundancy faulttolerant
techniques are application autonomy, cost-effectiveness and
better usage of system resources. Such advantage is very important
for many systems and especially for embedded ones.
Abstract: In this paper, an automated algorithm to estimate and remove the continuous baseline from measured spectra containing both continuous and discontinuous bands is proposed. The algorithm uses previous information contained in a Continuous Database Spectra (CDBS) to obtain a linear basis, with minimum number of sampled vectors, capable of representing a continuous baseline. The proposed algorithm was tested by using a CDBS of flame spectra where Principal Components Analysis and Non-negative Matrix Factorization were used to obtain linear bases. Thus, the radical emissions of natural gas, oil and bio-oil flames spectra at different combustion conditions were obtained. In order to validate the performance in the baseline estimation process, the Goodness-of-fit Coefficient and the Root Mean-squared Error quality metrics were evaluated between the estimated and the real spectra in absence of discontinuous emission. The achieved results make the proposed method a key element in the development of automatic monitoring processes strategies involving discontinuous spectral bands.
Abstract: This paper presents the design and analysis of a parallel
connected inverter configuration of. The configuration consists of
parallel connected three-phase dc/ac inverter. Series resistors added
to the inverter output to maintain same current in each inverter of the
two parallel inverters, and to reduce the circulating current in the
parallel inverters to the minimum. High frequency third harmonic
injection PWM (THIPWM) employed to reduce the total harmonic
distortion and to make maximum use of the voltage source. DSP was
used to generate the THIPWM and the control algorithm for the
converter. Selected experimental results have been shown to validate
the proposed system.
Abstract: Microparticles carrier systems made from naturally occurring polymers based on chitosan/casein system appears to be a promising carrier for the sustained release of orally and parenteral administered drugs. In the current study we followed a microencapsulation technique based aqueous coacervation method to prepare chitosan/casein microparticles of compositions 1:1, 1:2 and 1:5 incorporated with chloramphenicol. Glutaraldehyde was used as a chemical cross-linking agent. The microparticles were prepared by aerosol method and studied by optical microscopy, infrared spectroscopy, thermo gravimetric analysis, swelling studies and drug release studies at various pH. The percentage swelling of the polymers are found to be in the order pH 4 > pH 10 > pH 7 and the increase in casein composition decrease the swelling percentage. The drug release studies also follow the above order.
Abstract: Knowledge is renowned as a significant component
for sustaining competitive advantage and gives leading edge in
business. This study emphasizes towards proper and effectuate
utilization of internal and external (both either explicit or tacit)
knowledge comes from stakeholders, highly supportive to combat
with the challenges and enhance organizational productivity.
Furthermore, it proposed a model under context of IRSA framework
which facilitates the organization including flow of knowledge and
experience sharing among employees. In discussion section an
innovative model which indulges all functionality as mentioned in
analysis section.
Abstract: Network on Chip (NoC) has emerged as a promising
on chip communication infrastructure. Three Dimensional Integrate
Circuit (3D IC) provides small interconnection length between layers
and the interconnect scalability in the third dimension, which can
further improve the performance of NoC. Therefore, in this paper,
a hierarchical cluster-based interconnect architecture is merged with
the 3D IC. This interconnect architecture significantly reduces the
number of long wires. Since this architecture only has approximately
a quarter of routers in 3D mesh-based architecture, the average
number of hops is smaller, which leads to lower latency and higher
throughput. Moreover, smaller number of routers decreases the area
overhead. Meanwhile, some dual links are inserted into the bottlenecks
of communication to improve the performance of NoC.
Simulation results demonstrate our theoretical analysis and show the
advantages of our proposed architecture in latency, throughput and
area, when compared with 3D mesh-based architecture.