Abstract: Polycyclic aromatic hydrocarbons (PAHs) are formed
during the pyrolysis of scrap tyres to produce tyre pyrolytic oil
(TPO). Due to carcinogenic, mutagenic, and toxic properties PAHs
are priority pollutants. Hence it is essential to remove PAHs from
TPO before utilising TPO as a petroleum fuel alternative (to run the
engine). Agricultural wastes have promising future to be utilized as
biosorbent due to their cost effectiveness, abundant availability, high
biosorption capacity and renewability. Various low cost adsorbents
were prepared from natural sources. Uptake of PAHs present in tyre
pyrolytic oil was investigated using various low-cost adsorbents of
natural origin including sawdust (shisham), coconut fiber, neem bark,
chitin, activated charcoal. Adsorption experiments of different PAHs
viz. naphthalene, acenaphthalene, biphenyl and anthracene have been
carried out at ambient temperature (25°C) and at pH 7. It was
observed that for any given PAH, the adsorption capacity increases
with the lignin content. Freundlich constant Kf and 1/n have been
evaluated and it was found that the adsorption isotherms of PAHs
were in agreement with a Freundlich model, while the uptake
capacity of PAHs followed the order: activated charcoal> saw dust
(shisham) > coconut fiber > chitin. The partition coefficients in
acetone-water, and the adsorption constants at equilibrium, could be
linearly correlated with octanol–water partition coefficients. It is
observed that natural adsorbents are good alternative for PAHs
removal. Sawdust of Dalbergia sissoo, a by-product of sawmills was
found to be a promising adsorbent for the removal of PAHs present in
TPO. It is observed that adsorbents studied were comparable to those
of some conventional adsorbents.
Abstract: This work introduces a simple device designed to
perform in-situ direct shear and sinkage tests on granular materials
as sand, clays, or regolith. It consists of a box nested within a larger
box. Both have open bottoms, allowing them to be lowered into the
material. Afterwards, two rotating plates on opposite sides of the
outer box will rotate outwards in order to clear regolith on either
side, providing room for the inner box to move relative to the plates
and perform a shear test without the resistance of the surrounding
soil. From this test, Coulomb parameters, including cohesion and
internal friction angle, as well as, Bekker parameters can be inferred.
This device has been designed for a laboratory setting, but with few
modifications, could be put on the underside of a rover for use in
a remote location. The goal behind this work is to ultimately create
a compact, but accurate measuring tool to put onto a rover or any
kind of exploratory vehicle to test for regolith properties of celestial
bodies.
Abstract: Blueberries are widely valued for their high content in
phenolic compounds with antioxidant activity, and hence beneficial
for the human health. In this way, a study was done to determine the
phenolic composition (total phenols, anthocyanins and tannins) and
antioxidant activity of blueberries from three cultivars (Duke,
Bluecrop, and Ozarkblue) grown in two different Portuguese farms.
Initially two successive extractions were done with methanol
followed by two extractions with aqueous acetone solutions. These
extracts obtained were then used to evaluate the amount of phenolic
compounds and the antioxidant activity. The total phenols were
observed to vary from 4.9 to 8.2 mg GAE/g fresh weight, with
anthocyanin’s contents in the range 1.5-2.8 mg EMv3G/g and tannins
contents in the range 1.5- 3.8 mg/g. The results for antioxidant
activity ranged from 9.3 to 23.2 molTE/g and from 24.7 to 53.4molTE/g, when measured, respectively, by DPPH and ABTS
methods. In conclusion it was observed that, in general, the cultivar
had a visible effect on the phenols present, and furthermore, the
geographical origin showed relevance either in the phenols contents
or the antioxidant activity.
Abstract: In this paper, groundwater seepage into Amirkabir
tunnel has been estimated using analytical and numerical methods for
14 different sections of the tunnel. Site Groundwater Rating (SGR)
method also has been performed for qualitative and quantitative
classification of the tunnel sections. The obtained results of above
mentioned methods were compared together. The study shows
reasonable accordance with results of the all methods unless for two
sections of tunnel. In these two sections there are some significant
discrepancies between numerical and analytical results mainly
originated from model geometry and high overburden. SGR and the
analytical and numerical calculations, confirm high concentration of
seepage inflow in fault zones. Maximum seepage flow into tunnel has
been estimated 0.425 lit/sec/m using analytical method and 0.628
lit/sec/m using numerical method occured in crashed zone. Based on
SGR method, six sections of 14 sections in Amirkabir tunnel axis are
found to be in "No Risk" class that is supported by the analytical and
numerical seepage value of less than 0.04 lit/sec/m.
Abstract: The implementation of e-assessment as tool to support
the process of teaching and learning in university has become a
popular technological means in universities. E-Assessment provides
many advantages to the users especially the flexibility in teaching and
learning. The e-assessment system has the capability to improve its
quality of delivering education. However, there still exists a
drawback in terms of security which limits the user acceptance of the
online learning system. Even though there are studies providing
solutions for identified security threats in e-learning usage, there is no
particular model which addresses the factors that influences the
acceptance of e-assessment system by lecturers from security
perspective. The aim of this study is to explore security aspects of eassessment
in regard to the acceptance of the technology. As a result
a conceptual model of secure acceptance of e-assessment is proposed.
Both human and security factors are considered in formulation of this
conceptual model. In order to increase understanding of critical issues
related to the subject of this study, interpretive approach involving
convergent mixed method research method is proposed to be used to
execute the research. This study will be useful in providing more
insightful understanding regarding the factors that influence the user
acceptance of e-assessment system from security perspective.
Abstract: Maize constitutes a major agrarian production for use
by the vast population but despite its economic importance; it has not
been produced to meet the economic needs of the country. Achieving
optimum yield in maize can meaningfully be supported by land
suitability analysis in order to guarantee self-sufficiency for future
production optimization. This study examines land suitability for
maize production through the analysis of the physicochemical
variations in soil properties and other land attributes over space using
a Geographic Information System (GIS) framework.
Physicochemical parameters of importance selected include slope,
landuse, physical and chemical properties of the soil, and climatic
variables. Landsat imagery was used to categorize the landuse,
Shuttle Radar Topographic Mapping (SRTM) generated the slope and
soil samples were analyzed for its physical and chemical components.
Suitability was categorized into highly, moderately and marginally
suitable based on Food and Agricultural Organisation (FAO)
classification, using the Analytical Hierarchy Process (AHP)
technique of GIS. This result can be used by small scale farmers for
efficient decision making in the allocation of land for maize
production.
Abstract: Established objective and subjective preconditions for
entrepreneurship, forming the business organically related whole, are
the necessary condition of successful entrepreneurial activities.
Objective preconditions for entrepreneurship are developed by
market economy that should stimulate entrepreneurship by allowing
the use of economic opportunities for all those who want to do
business in respective field while providing guarantees to all owners
and creating a stable business environment for entrepreneurs.
Subjective preconditions of entrepreneurship are formed primarily by
personal characteristics of the entrepreneur. These are his properties,
abilities, skills, physiological and psychological preconditions which
may be inherited, inborn or sequentially developed and obtained
during his life on the basis of education and influences of
surrounding environment. The paper is dealing with issues of
objective and subjective preconditions for entrepreneurship and
provides their analysis in view of the current situation in Slovakia. It
presents risks of the business environment in Slovakia that the Slovak
managers considered the most significant in 2014 and defines the
dominant attributes of the entrepreneur in the current business
environment in Slovakia.
Abstract: Analysis of the properties of coconut (Cocos nucifera)
and its oil was evaluated in this work using standard analytical
techniques. The analyses carried out include proximate composition
of the fruit, extraction of oil from the fruit using different process
parameters and physicochemical analysis of the extracted oil. The
results showed the percentage (%) moisture, crude lipid, crude
protein, ash and carbohydrate content of the coconut as 7.59, 55.15,
5.65, 7.35 and 19.51 respectively. The oil from the coconut fruit was
odourless and yellowish liquid at room temperature (30oC). The
treatment combinations used (leaching time, leaching temperature
and solute: solvent ratio) showed significant differences (P
Abstract: China is currently the world's largest producer and distributor of electric bicycle (e-bike). The increasing number of e-bikes on the road is accompanied by rising injuries and even deaths of e-bike drivers. Therefore, there is a growing need to improve the safety structure of e-bikes. This 3D frictionless contact analysis is a preliminary, but necessary work for further structural design improvement of an e-bike. The contact analysis between e-bike and the ground was carried out as follows: firstly, the Penalty method was illustrated and derived from the simplest spring-mass system. This is one of the most common methods to satisfy the frictionless contact case; secondly, ANSYS static analysis was carried out to verify finite element (FE) models with contact pair (without friction) between e-bike and the ground; finally, ANSYS transient analysis was used to obtain the data of the penetration p(u) of e-bike with respect to the ground. Results obtained from the simulation are as estimated by comparing with that from theoretical method. In the future, protective shell will be designed following the stability criteria and added to the frame of e-bike. Simulation of side falling of the improvedsafety structure of e-bike will be confirmed with experimental data.
Abstract: At present, the cascade PID control is widely used to
control the superheating temperature (main steam temperature). As
Main Steam Temperature has the characteristics of large inertia, large
time-delay and time varying, etc., conventional PID control strategy
cannot achieve good control performance. In order to overcome the
bad performance and deficiencies of main steam temperature control
system, Model Free Adaptive Control (MFAC) - P cascade control
system is proposed in this paper. By substituting MFAC in PID of the
main control loop of the main steam temperature control, it can
overcome time delays, non-linearity, disturbance and time variation.
Abstract: The wide use of the Internet-based applications bring many challenges to the researchers to guarantee the continuity of the connections needed by the mobile hosts and provide reliable Internet access for them. One of proposed solutions by Internet Engineering Task Force (IETF) is to connect the local, multi-hop, and infrastructure-less Mobile Ad hoc Network (MANET) with Internet structure. This connection is done through multi-interface devices known as Internet Gateways. Many issues are related to this connection like gateway discovery, handoff, address auto-configuration and selecting the optimum gateway when multiple gateways exist. Many studies were done proposing gateway selection schemes with a single selection criterion or weighted multiple criteria. In this research, a review of some of these schemes is done showing the differences, the features, the challenges and the drawbacks of each of them.
Abstract: The edges of low contrast images are not clearly
distinguishable to human eye. It is difficult to find the edges and
boundaries in it. The present work encompasses a new approach for
low contrast images. The Chebyshev polynomial based fractional
order filter has been used for filtering operation on an image. The
preprocessing has been performed by this filter on the input image.
Laplacian of Gaussian method has been applied on preprocessed
image for edge detection. The algorithm has been tested on two test
images.
Abstract: Standard processes, similar and limited production
lines, the production of high direct costs will be more accurate than
the use of parts of the traditional cost systems in the literature.
However, direct costs, overhead expenses, in turn, decrease the
burden of increasingly sophisticated production facilities, a situation
that led the researchers to look for the cost of traditional systems of
alternative techniques. Variety cost management approaches for
example Total quality management (TQM), just-in-time (JIT),
benchmarking, kaizen costing, targeting cost, life cycle costs (LLC),
activity-based costing (ABC) value engineering have been
introduced. Management and cost applications have changed over the
past decade and will continue to change. Modern cost systems can
provide relevant and accurate cost information. These methods
provide the decisions about customer, product and process
improvement. The aim of study is to describe and explain the
adoption and application of costing systems in SME. This purpose
reports on a survey conducted during 2014 small and medium sized
enterprises (SME) in Ankara. The survey results were evaluated
using SPSS18 package program.
Abstract: Mechanical stress has a strong effect on the magnitude
of the Barkhausen-noise in structural steels. Because the
measurements are performed at the surface of the material, for a
sample sheet, the full effect can be described by a biaxial stress field.
The measured Barkhausen-noise is dependent on the orientation of
the exciting magnetic field relative to the axis of the stress tensor.
The sample inhomogenities including the residual stress also
modifies the angular dependence of the measured Barkhausen-noise.
We have developed a laboratory device with a cross like specimen
for bi-axial bending. The measuring head allowed performing
excitations in two orthogonal directions. We could excite the two
directions independently or simultaneously with different amplitudes.
The simultaneous excitation of the two coils could be performed in
phase or with a 90 degree phase shift. In principle this allows to
measure the Barkhausen-noise at an arbitrary direction without
moving the head, or to measure the Barkhausen-noise induced by a
rotating magnetic field if a linear superposition of the two fields can
be assumed.
Abstract: Living today in turbulent business environment forces
companies to distinguish from each other, securing sustainable
competitive growth and competitive advantage. The best possible
solution is to invest (effort and financial resources) within
companies’ different practices of human resource management
(HRM), more specifically in employees’ knowledge, skills and
abilities. Applying this approach companies will create enviable level
of human capital securing its economic growth. Employees become
human capital for their employers at the moment when they
contribute with their own knowledge and abilities in creating material
and non-material value of the company. The main aim of this
research is to explore the relations between human capital
investments and business excellence of Croatian companies.
Furthermore, the differences in the level of human capital
investments with regard to several companies’ characteristics (e.g.
size of the company, ownership and type of the industry) are
investigated.
Abstract: Constructing a portfolio of investments is one of the
most significant financial decisions facing individuals and
institutions. In accordance with the modern portfolio theory
maximization of return at minimal risk should be the investment goal
of any successful investor. In addition, the costs incurred when
setting up a new portfolio or rebalancing an existing portfolio must
be included in any realistic analysis.
In this paper rebalancing an investment portfolio in the presence of
transaction costs on the Croatian capital market is analyzed. The
model applied in the paper is an extension of the standard portfolio
mean-variance optimization model in which transaction costs are
incurred to rebalance an investment portfolio. This model allows
different costs for different securities, and different costs for buying
and selling. In order to find efficient portfolio, using this model, first,
the solution of quadratic programming problem of similar size to the
Markowitz model, and then the solution of a linear programming
problem have to be found. Furthermore, in the paper the impact of
transaction costs on the efficient frontier is investigated. Moreover, it
is shown that global minimum variance portfolio on the efficient
frontier always has the same level of the risk regardless of the amount
of transaction costs. Although efficient frontier position depends of
both transaction costs amount and initial portfolio it can be concluded
that extreme right portfolio on the efficient frontier always contains
only one stock with the highest expected return and the highest risk.
Abstract: This study aims to investigate the possibility of crime
prevention through CCTV by analyzing the appropriateness of the
CCTV location, whether it is installed in the hotspot of crime-prone
areas, and exploring the crime prevention effect and transition effect.
The real crime and CCTV locations of case city were converted into
the spatial data by using GIS. The data was analyzed by hotspot
analysis and weighted displacement quotient (WDQ). As study
methods, it analyzed existing relevant studies for identifying the trends
of CCTV and crime studies based on big data from 1800 to 2014 and
understanding the relation between CCTV and crime. Second, it
investigated the current situation of nationwide CCTVs and analyzed
the guidelines of CCTV installation and operation to draw attention to
the problems and indicating points of CCTV use. Third, it investigated
the crime occurrence in case areas and the current situation of CCTV
installation in the spatial aspects, and analyzed the appropriateness and
effectiveness of CCTV installation to suggest a rational installation of
CCTV and the strategic direction of crime prevention. The results
demonstrate that there was no significant effect in the installation of
CCTV on crime prevention in the case area. This indicates that CCTV
should be installed and managed in a more scientific way reflecting
local crime situations. In terms of CCTV, the methods of spatial
analysis such as GIS, which can evaluate the installation effect, and the
methods of economic analysis like cost-benefit analysis should be
developed. In addition, these methods should be distributed to local
governments across the nation for the appropriate installation of
CCTV and operation. This study intended to find a design guideline of
the optimum CCTV installation. In this regard, this study is
meaningful in that it will contribute to the creation of a safe city.
Abstract: It has become an increasing evident that large
development influences the climate. There are concerns that rising
temperature over developed areas could have negative impact and
increase living discomfort within city boundaries. Temperature trends
in Ibadan city have received little attention, yet the area has
experienced heavy urban expansion between 1972 and 2014. This
research aims at examining the impact of landuse change on surface
temperature knowing that the built-up environment absorb and store
solar energy, resulting into the Urban Heat Island (UHI) effect. The
Landsat imagery was used to examine the landuse change for a
period of 42 years (1972-2014). Land Surface Temperature (LST)
was obtained by converting the thermal band to a surface temperature
map and zonal statistic analyses was used to examine the relationship
between landuse and temperature emission. The results showed that
the settlement area increased to a large extent while the area covered
by vegetation reduced during the study period. The spatial and
temporal trends of surface temperature are related to the gradual
change in urban landuse/landcover and the settlement area has the
highest emission. This research provides useful insight into the
temporal behavior of the Ibadan city.
Abstract: A Disaster Management System (DMS) is very important for countries with multiple disasters, such as Chile. In the world (also in Chile)different disasters (earthquakes, tsunamis, volcanic eruption, fire or other natural or man-made disasters) happen and have an effect on the population. It is also possible that two or more disasters occur at the same time. This meansthata multi-risk situation must be mastered. To handle such a situation a Decision Support System (DSS) based on multiagents is a suitable architecture. The most known DMSs are concernedwith only a singledisaster (sometimes thecombination of earthquake and tsunami) and often with a particular disaster. Nevertheless, a DSS helps for a better real-time response. Analyze the existing systems in the literature and expand them for multi-risk disasters to construct a well-organized system is the proposal of our work. The here shown work is an approach of a multi-risk system, which needs an architecture and well defined aims. In this moment our study is a kind of case study to analyze the way we have to follow to create our proposed system in the future.
Abstract: The Cone Penetration Test (CPT) is a common in-situ
test which generally investigates a much greater volume of soil more
quickly than possible from sampling and laboratory tests. Therefore,
it has the potential to realize both cost savings and assessment of soil
properties rapidly and continuously. The principle objective of this
paper is to demonstrate the feasibility and efficiency of using
artificial neural networks (ANNs) to predict the soil angle of internal
friction (Φ) and the soil modulus of elasticity (E) from CPT results
considering the uncertainties and non-linearities of the soil. In
addition, ANNs are used to study the influence of different
parameters and recommend which parameters should be included as
input parameters to improve the prediction. Neural networks discover
relationships in the input data sets through the iterative presentation
of the data and intrinsic mapping characteristics of neural topologies.
General Regression Neural Network (GRNN) is one of the powerful
neural network architectures which is utilized in this study. A large
amount of field and experimental data including CPT results, plate
load tests, direct shear box, grain size distribution and calculated data
of overburden pressure was obtained from a large project in the
United Arab Emirates. This data was used for the training and the
validation of the neural network. A comparison was made between
the obtained results from the ANN's approach, and some common
traditional correlations that predict Φ and E from CPT results with
respect to the actual results of the collected data. The results show
that the ANN is a very powerful tool. Very good agreement was
obtained between estimated results from ANN and actual measured
results with comparison to other correlations available in the
literature. The study recommends some easily available parameters
that should be included in the estimation of the soil properties to
improve the prediction models. It is shown that the use of friction
ration in the estimation of Φ and the use of fines content in the
estimation of E considerable improve the prediction models.