Abstract: Advanced treatments such as forward osmosis (FO)
can be used to separate or reject nutrients from secondary treated
effluents. Forward osmosis uses the chemical potential across the
membrane, which is the osmotic pressure gradient, to induce water to
flow through the membrane from a feed solution (FS) into a draw
solution (DS). The performance of FO is affected by the membrane
characteristics, composition of the FS and DS, and operating
conditions. The aim of this study was to investigate the optimum
velocity and temperature for nutrient rejection and water flux
performance in FO treatments. MgCl2 was used as the DS in the FO
process. The results showed that higher cross flow velocities yielded
higher water fluxes. High rejection of nutrients was achieved by using
a moderate cross flow velocity at 0.25 m/s. Nutrient rejection was
insensitive to temperature variation, whereas water flux was
significantly impacted by it. A temperature of 25°C was found to be
good for nutrient rejection.
Abstract: The Orthogonal Frequency Division Multiplexing
(OFDM) with high data rate, high spectral efficiency and its ability to
mitigate the effects of multipath makes them most suitable in wireless
application. Impulsive noise distorts the OFDM transmission and
therefore methods must be investigated to suppress this noise. In this
paper, a State Space Recursive Least Square (SSRLS) algorithm
based adaptive impulsive noise suppressor for OFDM
communication system is proposed. And a comparison with another
adaptive algorithm is conducted. The state space model-dependent
recursive parameters of proposed scheme enables to achieve steady
state mean squared error (MSE), low bit error rate (BER), and faster
convergence than that of some of existing algorithm.
Abstract: In this paper, we propose a system for preventing gas
risks through the use of wireless communication modules and
intelligent gas safety appliances. Our system configuration consists of
an automatic extinguishing system, detectors, a wall-pad, and a
microcomputer controlled micom gas meter to monitor gas flow and
pressure as well as the occurrence of earthquakes. The automatic fire
extinguishing system checks for both combustible gaseous leaks and
monitors the environmental temperature, while the detector array
measures smoke and CO gas concentrations. Depending on detected
conditions, the micom gas meter cuts off an inner valve and generates
a warning, the automatic fire-extinguishing system cuts off an external
valve and sprays extinguishing materials, or the sensors generate
signals and take further action when smoke or CO are detected.
Information on intelligent measures taken by the gas safety appliances
and sensors are transmitted to the wall-pad, which in turn relays this as
real time data to a server that can be monitored via an external network
(BcN) connection to a web or mobile application for the management
of gas safety. To validate this smart-home gas management system, we
field-tested its suitability for use in Korean apartments under several
scenarios.
Abstract: Here, we study the characteristic feature of
conventional (ON-OFF keying) and soliton based transmission
system. We consider 20Gbps transmission system implemented with
Conventional Single Mode Fiber (C-SMF) to examine the role of
Gaussian pulse which is the characteristic of conventional
propagation and Hyperbolic-secant pulse which is the characteristic
of soliton propagation in it. We note the influence of these pulses
with respect to different dispersion lengths and soliton period in
conventional and soliton system respectively and evaluate the system
performance in terms of Quality factor. From the analysis, we could
prove that the soliton pulse has the consistent performance even for
long distance without dispersion compensation than the conventional
system as it is robust to dispersion. For the length of transmission of
200Km, soliton system yielded Q of 33.958 while the conventional
system totally exhausted with Q=0.
Abstract: Microstructural and hardening changes of
Fe-0.2wt.%V alloy and pure Fe irradiated with 100 keV hydrogen ions
at room temperature were investigated. It was found that dislocation
density varies dramatically after irradiation, ranging from dislocation
free to dense areas with tangled and complex dislocation
configuration. As the irradiated Fe-0.2wt.%V samples were annealed
at 773 K, the irradiation-induced dislocation loops disappear, while
many small precipitates with enriched C distribute in the matrix. Some
large precipitates with enriched V were also observed. The hardness of
Fe-0.2wt.%V alloy and pure Fe increases after irradiation, which
ascribes to the formation of dislocation loops in the irradiated
specimens. Compared with pure Fe, the size of the
irradiation-introduced dislocation loops in Fe-0.2wt.%V alloy
decreases and the density increases, the change of the hardness also
decreases.
Abstract: Phthalates are ubiquitous environmental pollutants
well known because of their endocrine disrupting activity in human
organism. The aim of our study was, by biological monitoring,
investigate exposure to phthalates of Roma ethnicity group i.e.
children and adults from 5 families (n=29, average age 11.8 ± 7.6
years) living in western Slovakia. Additionally, we analysed some
associations between anthropometric measures, questionnaire data
i.e. socio-economic status, eating and drinking habits, practise of
personal care products and household conditions in comparison with
concentrations of phthalate metabolites. We used for analysis of urine
samples high performance liquid chromatography and tandem mass
spectrometry (HPLC-MS/MS) to determine concentrations of
phthalate metabolites monoethyl phthalate (MEP), mono-n-butyl
phthalate (MnBP), mono-iso-butyl phthalate (MiBP), mono(2-ethyl-
5-hydroxyhexyl) phthalate (5OH-MEHP), mono(2-ethyl-5-oxohexyl)
phthalate (5oxo-MEHP) and mono(2-etylhexyl) phthalate (MEHP).
Our results indicate that ethnicity, lower socioeconomic status and
different housing conditions in Roma population can affect urinary
concentration of phthalate metabolites.
Abstract: The separation of Hg (II) from produced water by
hollow fiber contactors (HFC) was investigation. This system
included of two hollow fiber modules in the series connecting. The
first module used for the extraction reaction and the second module
for stripping reaction. Aliquat336 extractant was fed from the organic
reservoirs into the shell side of the first hollow fiber module and
continuous to the shell side of the second module. The organic liquid
was continuously feed recirculate and back to the reservoirs. The feed
solution was pumped into the lumen (tube side) of the first hollow
fiber module. Simultaneously, the stripping solution was pumped in
the same way in tube side of the second module. The feed and
stripping solution was fed which had a countercurrent flow. Samples
were kept in the outlet of feed and stripping solution at 1 hour and
characterized concentration of Hg (II) by Inductively Couple Plasma
Atomic Emission Spectroscopy (ICP-AES). Feed solution was
produced water from natural gulf of Thailand. The extractant was
Aliquat336 dissolved in kerosene diluent. Stripping solution used was
nitric acid (HNO3) and thiourea (NH2CSNH2). The effect of carrier
concentration and type of stripping solution were investigated.
Results showed that the best condition were 10 % (v/v) Aliquat336
and 1.0 M NH2CSNH2. At the optimum condition, the extraction and
stripping of Hg (II) were 98% and 44.2%, respectively.
Abstract: In the present study, RBF neural networks were used
for predicting the performance and emission parameters of a
biodiesel engine. Engine experiments were carried out in a 4 stroke
diesel engine using blends of diesel and Honge methyl ester as the
fuel. Performance parameters like BTE, BSEC, Tex and emissions
from the engine were measured. These experimental results were
used for ANN modeling.
RBF center initialization was done by random selection and by
using Clustered techniques. Network was trained by using fixed and
varying widths for the RBF units. It was observed that RBF results
were having a good agreement with the experimental results.
Networks trained by using clustering technique gave better results
than using random selection of centers in terms of reduced MRE and
increased prediction accuracy. The average MRE for the performance
parameters was 3.25% with the prediction accuracy of 98% and for
emissions it was 10.4% with a prediction accuracy of 80%.
Abstract: The polymer foil used for manufacturing of
laminated glass members behaves in a viscoelastic manner with
temperature dependance. This contribution aims at incorporating
the time/temperature-dependent behavior of interlayer to our earlier
elastic finite element model for laminated glass beams. The model
is based on a refined beam theory: each layer behaves according
to the finite-strain shear deformable formulation by Reissner and
the adjacent layers are connected via the Lagrange multipliers
ensuring the inter-layer compatibility of a laminated unit. The
time/temperature-dependent behavior of the interlayer is accounted
for by the generalized Maxwell model and by the time-temperature
superposition principle due to the Williams, Landel, and Ferry.
The resulting system is solved by the Newton method with
consistent linearization and the viscoelastic response is determined
incrementally by the exponential algorithm. By comparing the model
predictions against available experimental data, we demonstrate that
the proposed formulation is reliable and accurately reproduces the
behavior of the laminated glass units.
Abstract: This paper presents a rank correlation curve. The
traditional correlation coefficient is valid for both continuous
variables and for integer variables using rank statistics. Since
the correlation coefficient has already been established in rank
statistics by Spearman, such a calculation can be extended to
the correlation curve.
This paper presents two survey questions. The survey
collected non-continuous variables. We will show weak to
moderate correlation. Obviously, one question has a negative
effect on the other. A review of the qualitative literature
can answer which question and why. The rank correlation
curve shows which collection of responses has a positive
slope and which collection of responses has a negative slope.
Such information is unavailable from the flat, ”first-glance”
correlation statistics.
Abstract: The need to use high volumes of data and the high
competition are only two reasons which make necessary the use of
information technologies. The objective of our research is to establish
the impact of information technologies on the accounting department
of the Romanian companies. In order to achieve it, starting from the
literature review we made an empirical research based on a
questionnaire. We investigated the types of technologies used, the
reasons which led to the implementation of certain technologies, the
benefits brought by the use of the information technologies, the
difficulties brought by the implementation and the future effects of
the applications. The conclusions show that there is an evolution in
the degree of implementation of the information technologies in the
Romanian companies, compared with the results of other studies
conducted a few years before.
Abstract: Quantitative radiobiological models can be used to
assess the optimum clinical outcome from sophisticated therapeutic
modalities by calculating tumor control probability (TCP) and normal
tissue complication probability (NTCP). In this study two 3D-CRT
and an IMRT treatment plans were developed with an initial
prescription dose of 60 Gy in 2 Gy/fraction to prostate. Sensitivity of
TCP and Complication free tumor control probability (P+) to the
different values of α/β ratio was investigated for various prescription
doses planned to be delivered in either a fixed number of fractions (I)
or in a fixed dose per fraction (II) in each of the three different
treatment plans. High dose/fraction and high α/β value result in
comparatively smaller P+ and IMRT plans resulted in the highest P+,
mainly due to the decrease in NTCP. If α/β is lower than expected,
better tumor control can be achieved by increasing dose/fraction but
decreasing the number of fractions.
Abstract: Medicinal plants are now gaining attractiveness in
treatment of bacterial infections and food preservation. The objective
of this study was to assess antibacterial activity of some medicinal
plants on pathogenic bacteria. Screening of antibacterial activity of
aqueous and methanol extracts of some plants: Jojoba, Ginger, Sage,
Thyme and Clove against Bacillus cereus, Salmonella typhimurium,
Staphylococcus aureus, Clostridium perfringens and Escherichia coli
were investigated. Antibacterial activity was performed by agar
diffusion and disc diffusion method. Jatropha, Jojoba, Clove and
Ginger extracts showed notable bacterial activity in the first
screening step then selected to be tested against Bacillus cereus
(Gram+), Staphylococcus aureus (Gram+) and Salmonella
typhimurium (Gram−) and their effect was compared using
antibiotics as control. Screening results showed potential antibacterial
activity of the tested plant extracts against the screened bacterial
strains. It was found that methanol extracts exhibited higher
antibacterial activity than aqueous extracts. Methanol extract of
Jatropha showed the highest inhibition zone against Staphylococcus
aureus (Gram+) with 24.00 mm diameter, compared to the other
plant extracts followed by clove. Meanwhile, the inhibition zones of
methanol extracts of Jojoba and Ginger were the same (12mm).The
Gram-positive bacteria were found to be more sensitive to aqueous
and methanol extracts than Gram-negative bacteria.
Abstract: This paper analyses the heat transfer performance and
fluid flow using different nanofluids in a square enclosure. The
energy equation and Navier-Stokes equation are solved numerically
using finite volume scheme. The effect of volume fraction
concentration on the enhancement of heat transfer has been studied
icorporating the Brownian motion; the influence of effective thermal
conductivity on the enhancement was also investigated for a range of
volume fraction concentration. The velocity profile for different
Rayleigh number. Water-Cu, water AL2O3 and water-TiO2 were
tested.
Abstract: The article presents a plasma chemical technology for
processing solid fuels, using examples of bituminous and brown
coals. Thermodynamic and experimental investigation of the
technology was made. The technology allows producing synthesis
gas from the coal organic mass and valuable components (technical
silicon, ferrosilicon, aluminum, and carbon silicon, as well as
microelements of rare metals, such as uranium, molybdenum,
vanadium, etc.) from the mineral mass. The thusly produced highcalorific
synthesis gas can be used for synthesis of methanol, as a
high-calorific reducing gas instead of blast-furnace coke as well as
power gas for thermal power plants.
Abstract: The posterior reference for the ala tragal line is a
cause of confusion, with different authors suggesting different
locations as to the superior, middle or inferior part of the tragus. This
study was conducted on 200 subjects to evaluate if any correlation
exists between the variation of angulation of palatal throat form and
the relative parallelism of occlusal plane to ala-tragal line at different
tragal levels. A custom made Occlusal Plane Analyzer was used to
check the parallelism between the ala-tragal line and occlusal plane.
A lateral cephalogram was shot for each subject to measure the
angulation of the palatal throat form. Fisher’s exact test was used to
evaluate the correlation between the angulation of the palatal throat
form and the relative parallelism of occlusal plane to the ala tragal
line. Also, a classification was formulated for the palatal throat form,
based on confidence interval. From the results of the study, the
inferior part, middle part and superior part of the tragus were seen as
the reference points in 49.5%, 32% and 18.5% of the subjects
respectively. Class I palatal throat form (41degree-50 degree), Class
II palatal throat form (below 41 degree) and Class III palatal throat
form (above 50 degree) were seen in 42%, 43% and 15% of the
subjects respectively. It was also concluded that there is no
significant correlation between the variation in the angulations of the
palatal throat form and the relative parallelism of occlusal plane to
the ala-tragal line.
Abstract: We propose new multiple-channel piezoelectric (PZT)
actuated tunable optical filter based on racetrack multi-ring
resonators for wavelength de-multiplexing network applications. We
design tunable eight-channel wavelength de-multiplexer consisting of
eight cascaded PZT actuated tunable multi-ring resonator filter with a
channel spacing of 1.6nm. The filter for each channel is basically
structured on a suspended beam, sandwiched with piezoelectric
material and built in integrated ring resonators which are placed on
the middle of the beam to gain uniform stress and linearly varying
longitudinal strain. A reference single mode serially coupled multi
stage racetrack ring resonator with the same radii and coupling length
is designed with a line width of 0.8974nm with a flat top pass band at
1dB of 0.5205nm and free spectral range of about 14.9nm. In each
channel, a small change in the perimeter of the rings is introduced to
establish the shift in resonance wavelength as per the defined channel
spacing. As a result, when a DC voltage is applied, the beams will
elongate, which involves mechanical deformation of the ring
resonators that induces a stress and a strain, which brings a change in
refractive index and perimeter of the rings leading to change in the
output spectrum shift providing the tunability of central wavelength
in each channel. Simultaneous wave length shift as high as
45.54pm/
Abstract: In wastewater treatment processes, aeration introduces
air into a liquid. In these systems, air is introduced by different
devices submerged in the wastewater. Smaller bubbles result in more
bubble surface area per unit of volume and higher oxygen transfer
efficiency. Jet pumps are devices that use air bubbles and are widely
used in wastewater treatment processes. The principle of jet pumps is
their ability to transfer energy of one fluid, called primary or motive,
into a secondary fluid or gas. These pumps have no moving parts and
are able to work in remote areas under extreme conditions. The
objective of this work is to study experimentally the characteristics of
the jet pump and the size of air bubbles in the laboratory water tank.
The effect of flow rate ratio on pump performance is investigated in
order to have a better understanding about pump behavior under
various conditions, in order to determine the efficiency of receiving
air bubbles different sizes. The experiments show that we should take
care when increasing the flow rate ratio while seeking to decrease
bubble size in the outlet flow. This study will help improve and
extend the use of the jet pump in many practical applications.
Abstract: Many industrial materials like magnets need to be
tested for the radiation environment expected at linear colliders (LC)
where the accelerator and detectors will be subjected to large
influences of beta, neutron and gamma’s over their life Gamma
irradiation of the permanent sample magnets using a 60Co source was
investigated up to an absorbed dose of 700Mrad shows a negligible
effect on some magnetic properties of Nd-Fe-B. In this work it has
been tried to investigate the change of some important properties of
Barium hexa ferrite. Results showed little decreases of magnetic
properties at doses rang of 0.5 to 2.5 Mrad. But at the gamma
irradiation dose up to 10 Mrad it is showed a few increase of
properties. Also study of gamma irradiation of Nd-Fe-B showed
considerably increase of magnetic properties.
Abstract: A field study was conducted to evaluate the efficacy of
safflower plant for phytoremediation of contaminated soils. The
experiment was performed on an agricultural fields contaminated by
the Non-Ferrous-Metal Works near Plovdiv, Bulgaria. Field
experiments with randomized complete block design with five
treatments (control, compost amendments added at 20 and 40 t/daa,
and vermicompost amendments added at 20 and 40 t/daa) were
carried out. The quality of safflower seeds and oil (heavy metals and
fatty acid composition) were determined. Tested organic amendments
significantly influenced the chemical composition of safflower seeds
and oil. The compost and vermicompost treatments significantly
reduced heavy metals concentration in safflower seeds and oils, but
the effect differed among them. Addition of vermicompost and
compost leads to an increase in the content of palmitic acid and
linoleic acid, and a decrease in the stearic and oleic acids compared
with the control. A significant increase in the quantity of saturated
acids was observed in the variants with 20 t/daa of compost and 20
t/daa of vermicompost (9.1 and 8.9% relative to the control).
Safflower is a plant which is tolerant to heavy metals and can be
successfully used in the phytoremediation of heavy metal
contaminated soils. The processing of seeds to oil and using the
obtained oil for nutritional purposes will greatly reduce the cost of
phytoremediation.