Abstract: India holds 17.5% of the world’s population but has
only 2% of the total geographical area of the world where 27.35% of
the area is categorized as wasteland due to lack of or less
groundwater. So there is a demand for excessive groundwater for
agricultural and non agricultural activities to balance its growth rate.
With this in mind, an attempt is made to find the groundwater
potential zone in Gomukhi Nadhi sub basin of Vellar River basin,
TamilNadu, India covering an area of 1146.6 Sq.Km consists of 9
blocks from Peddanaickanpalayam to Virudhachalam in the sub
basin. The thematic maps such as Geology, Geomorphology,
Lineament, Landuse and Landcover and Drainage are prepared for
the study area using IRS P6 data. The collateral data includes rainfall,
water level, soil map are collected for analysis and inference. The
digital elevation model (DEM) is generated using Shuttle Radar
Topographic Mission (SRTM) and the slope of the study area is
obtained. ArcGIS 10.1 acts as a powerful spatial analysis tool to find
out the ground water potential zones in the study area by means of
weighted overlay analysis. Each individual parameter of the thematic
maps are ranked and weighted in accordance with their influence to
increase the water level in the ground. The potential zones in the
study area are classified viz., Very Good, Good, Moderate, Poor with
its aerial extent of 15.67, 381.06, 575.38, 174.49 Sq.Km respectively.
Abstract: The biosynthesis of nanoparticles by microorganisms,
on the contrary to chemical synthesis, is an environmentally-friendly
process which has low energy requirements. In this investigation, we
used the microorganism Geobacillus wiegelii, strain GWE1, an
aerobic thermophile belonging to genus Geobacillus, isolated from a
drying oven. This microorganism has the ability to reduce selenite
evidenced by the change of color from colorless to red in the culture.
Elemental analysis and composition of the particles were verified
using transmission electron microscopy and energy-dispersive X-ray
analysis. The nanoparticles have a defined spherical shape and a
selenium elemental state. Previous experiments showed that the
presence of the whole microorganism for the reduction of selenite
was not necessary. The results strongly suggested that an intracellular
NADPH/NADH-dependent reductase mediates selenium
nanoparticles synthesis under aerobic conditions. The enzyme was
purified and identified by mass spectroscopy MALDI-TOF TOF
technique. The enzyme is a 1-pyrroline-5-carboxylate dehydrogenase.
Histograms of nanoparticles sizes were obtained. Size distribution
ranged from 40-160 nm, where 70% of nanoparticles have less than
100 nm in size. Spectroscopic analysis showed that the nanoparticles
are composed of elemental selenium. To analyse the effect of pH in
size and morphology of nanoparticles, the synthesis of them was
carried out at different pHs (4.0, 5.0, 6.0, 7.0, 8.0). For
thermostability studies samples were incubated at different
temperatures (60, 80 and 100 ºC) for 1 h and 3 h. The size of all
nanoparticles was less than 100 nm at pH 4.0; over 50% of
nanoparticles have less than 100 nm at pH 5.0; at pH 6.0 and 8.0 over
90% of nanoparticles have less than 100 nm in size. At neutral pH
(7.0) nanoparticles reach a size around 120 nm and only 20% of them
were less than 100 nm. When looking at temperature effect,
nanoparticles did not show a significant difference in size when they
were incubated between 0 and 3 h at 60 ºC. Meanwhile at 80 °C the
nanoparticles suspension lost its homogeneity. A change in size was
observed from 0 h of incubation at 80ºC, observing a size range
between 40-160 nm, with 20% of them over 100 nm. Meanwhile
after 3 h of incubation at size range changed to 60-180 nm with 50%
of them over 100 nm. At 100 °C the nanoparticles aggregate forming
nanorod structures. In conclusion, these results indicate that is
possible to modulate size and shape of biologically synthesized
nanoparticles by modulating pH and temperature.
Abstract: Heightened concerns over the amount of carbon
emitted from coal-related processes are generating shifts to the
application of biomass. In co-gasification, where coal is gasified
along with biomass, the biomass may be fed together with coal (cofeeding)
or an independent biomass gasifier needs to be integrated
with the coal gasifier. The main aim of this work is to evaluate the
biomass introduction methods in coal co-gasification. This includes
the evaluation of biomass concentration input (B0 to B100) and its
gasification performance. A process model is developed and
simulated in Aspen HYSYS, where both coal and biomass are
modelled according to its ultimate analysis. It was found that the
syngas produced increased with increasing biomass content for both
co-feeding and independent schemes. However, the heating values
and heat duties decreases with biomass concentration as more CO2
are produced from complete combustion.
Abstract: At-site flood frequency analysis is used to estimate
flood quantiles when at-site record length is reasonably long. In
Australia, FLIKE software has been introduced for at-site flood
frequency analysis. The advantage of FLIKE is that, for a given
application, the user can compare a number of most commonly
adopted probability distributions and parameter estimation methods
relatively quickly using a windows interface. The new version of
FLIKE has been incorporated with the multiple Grubbs and Beck test
which can identify multiple numbers of potentially influential low
flows. This paper presents a case study considering six catchments in
eastern Australia which compares two outlier identification tests
(original Grubbs and Beck test and multiple Grubbs and Beck test)
and two commonly applied probability distributions (Generalized
Extreme Value (GEV) and Log Pearson type 3 (LP3)) using FLIKE
software. It has been found that the multiple Grubbs and Beck test
when used with LP3 distribution provides more accurate flood
quantile estimates than when LP3 distribution is used with the
original Grubbs and Beck test. Between these two methods, the
differences in flood quantile estimates have been found to be up to
61% for the six study catchments. It has also been found that GEV
distribution (with L moments) and LP3 distribution with the multiple
Grubbs and Beck test provide quite similar results in most of the
cases; however, a difference up to 38% has been noted for flood
quantiles for annual exceedance probability (AEP) of 1 in 100 for one
catchment. This finding needs to be confirmed with a greater number
of stations across other Australian states.
Abstract: An investigation into the effect of countersunk depth,
plate thickness, countersunk angle and plate width on the stress
concentration around countersunk hole is carried out with the help of
finite element analysis. The variation of stress concentration with
respect to these parameters is studied for three types of loading viz.
uniformly distributed load, uniformly varying load and functionally
distributed load. The results of the finite element analysis are
interpreted and some conclusions are drawn. The distribution of
stress concentration around countersunk hole in isotropic plates
simply supported at all the edges is found similar and is independent
of loading. The maximum stress concentration also occurs at a
particular point irrespective of the loading conditions.
Abstract: This paper is drawn from a wider study of the
management of gender, age and disability diversity in the banking
sector in the Kingdom of Saudi Arabia (KSA), which aims to develop
a framework for diversity management (DM) in this sector. The
paper focuses on the management of disability diversity. The purpose
of the paper is to assist in understanding disability DM in the banking
sector in KSA and to make suggestions for its enhancement. Hence, it
contributes to filling a research gap, as there is a dearth of literature
on disability DM, in KSA in general, and in the banking sector
specifically.
Discrimination against people with disabilities is a social issue that
has not been entirely overcome in any society. However, in KSA,
Islam informs almost every aspect of daily life including work, and
Islam is against discrimination. Hence, in KSA, there are regulations
to accommodate people with disabilities; however, employers are still
free not to hire job applicants with disabilities specifically because of
their condition. Indeed, disabled people are almost entirely absent
from the labour market.
There are 12 Saudi-owned or part-Saudi-owned banks in KSA and
two managers from each of these were interviewed, making a total of
24. The interviews aimed to investigate empirically the understanding
of managers in the banking sector in KSA of diversity management,
including disability DM, in the banking sector. The interview data
were analysed using thematic analysis. Two interviewees stated that
banks used the employment of people with disabilities to enhance
their corporate image, while five expressed the opinion that disabled
employees could contribute to the bank provided they did not have to
deal with customers face-to-face. Nine of the interviewees perceived
that disabled employees could be of value to the bank for their own
sake, not only in ‘behind the scenes’ roles. Another two interviewees
mentioned that employing disabled people could be part of the bank’s
community service programme and one thought it would be part of
the bank’s Saudisation efforts. The remaining five interviewees did
not know how disabled people could contribute to the bank.
The findings show that disability DM in the banking sector in
KSA is a relatively new concept, and is not yet well understood. In
the light of the findings, in order to achieve the purpose of the paper,
the following suggestions were made for the enhancement of
disability DM in the banking sector in KSA. A change in attitudes
towards disabled people is necessary. Such a change in the workplace
can only be achieved if a top-down approach is taken to the
integration of disabled people. Hence, it is suggested that
management and employees follow a course in disability awareness.
Further, a diversity officer in the HR department could enhance the
integration of disabled people into the banking workforce. It is also
suggested that greater government support is required through closely
monitored and enforced anti-discrimination legislation. Moreover,
flexible working arrangements such as part-time work would
facilitate the employment of disabled people and benefit other groups
of employees.
Abstract: Thanks to informational technologies development
every sphere of economics is becoming more and more datacentralized
as people are generating huge datasets containing
information on any aspect of their life. Applying research of such
data to human resources management allows getting scarce statistics
on labor market state including salary expectations and potential
employees’ typical career behavior, and this information can become
a reliable basis for management decisions.
The following article presents results of career behavior research
based on freely accessible resume data. Information used for study is
much wider than one usually uses in human resources surveys. That
is why there is enough data for statistically significant results even
for subgroups analysis.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: The asynchronous discussion forum is one of the most
widely used activities in learning management system environment.
Online forum allows participants to interact, construct knowledge,
and can be used to complement face to face sessions in blended
learning courses. However, to what extent do the students perceive
the benefits or advantages of forum remain to be seen. Through
content and social network analyses, instructors will be able to gauge
the students’ engagement and knowledge construction level. Thus,
this study aims to analyze the students’ level of knowledge
construction and their participation level that occur through online
discussion. It also attempts to investigate the relationship between the
level of knowledge construction and their social interaction patterns.
The sample involves 23 students undertaking a master course in one
public university in Malaysia. The asynchronous discussion forum
was conducted for three weeks as part of the course requirement. The
finding indicates that the level of knowledge construction is quite
low. Also, the density value of 0.11 indicating the overall
communication among the participants in the forum is low. This
study reveals that strong and significant correlations between SNA
measures (in-degree centrality, out-degree centrality) and level of
knowledge construction. Thus, allocating these active students in
different group aids the interactive discussion takes place. Finally,
based upon the findings, some recommendations to increase students’
level of knowledge construction and also for further research are
proposed.
Abstract: Bone properties and response behavior after static or
dynamic activation (loading) are still interesting topics in many fields
of the science especially in the biomechanical problems such as bone
loss of astronauts in space, osteoporosis, bone remodeling after
fracture or remodeling after surgery (endoprosthesis and implants)
and in osteointegration. This contribution deals with the relation
between physiological, demineralized and deproteinized state of the
turkey long bone – tibia. Three methods for comparison were used: 1)
densitometry, 2) three point bending and 3) frequency analysis. The
main goal of this work was to describe the decrease of the protein
(collagen) or mineral of the bone with relation to the fracture in three
point bending. The comparison is linked to the problem of different
bone mechanical behavior in physiological and osteoporotic state.
Abstract: Metallic foams have good potential for lightweight
structures for impact and blast mitigation. Therefore it is important to
find out the optimized foam structure (i.e. cell size, shape, relative
density, and distribution) to maximise energy absorption. In this
paper, quasistatic compression and microstructural characterization
of closed-cell aluminium foams of different pore size and cell
distributions have been carried out. We present results for two
different aluminium metal foams of density 0.49-0.51 g/cc and 0.31-
0.34 g/cc respectively that have been tested in quasi-static
compression. The influence of cell geometry and cell topology on
quasistatic compression behaviour has been investigated using optical
microscope and computed tomography (micro-CT) analysis. It is
shown that the deformation is not uniform in the structure and
collapse begins at the weakest point.
Abstract: Medical imaging technology has experienced a
dramatic change in the last few years. Medical imaging refers to the
techniques and processes used to create images of the human body
(or parts thereof) for various clinical purposes such as medical
procedures and diagnosis or medical science including the study of
normal anatomy and function. With the growth of computers and
image technology, medical imaging has greatly influenced the
medical field. The diagnosis of a health problem is now highly
dependent on the quality and the credibility of the image analysis.
This paper deals with the various aspects and types of medical
imaging.
Abstract: Human movement in the real world provides
important information for developing human behaviour models and
simulations. However, it is difficult to assess ‘real’ human behaviour
since there is no established method available. As part of the AUNTSUE
(Accessibility and User Needs in Transport – Sustainable Urban
Environments) project, this research aimed to propose a method to
assess human movement and behaviour in crowded areas. The
method is based on the three major steps of video recording,
conceptual behavior modelling and video analysis. The focus is on
individual human movement and behaviour in normal situations
(panic situations are not considered) and the interactions between
individuals in localized areas. Emphasis is placed on gaining
knowledge of characteristics of human movement and behaviour in
the real world that can be modelled in the virtual environment.
Abstract: Age ratings are very helpful in providing parents with
relevant information for the purchase and use of digital technologies
by the children; this is why the non-definition of age ratings for the
use of ICTs by children in schools is a major concern; and this
problem serves as a motivation for this study whose aim is to
examine the factors affecting the perceptions of educators on the
learners’ youngest age for the introduction of ICTs in schools. This
aim is achieved through two types of research objectives: the
identification and design of theories and models on age ratings, and
the empirical testing of such theories and models in a survey of
educators from the Camperdown district of the South African
KwaZulu-Natal province. A questionnaire is used for the collection
of the data of this survey whose validity and reliability is checked in
SPSS prior to its descriptive and correlative quantitative analysis. The
main hypothesis supporting this research is the association between
the demographics of educators, their personality, and their
perceptions on the learners’ youngest age for the introduction of ICTs
in schools; as claimed by existing research; except that the present
study looks at personality from three dimensions: self-actualized
personalities, fully functioning personalities, and healthy
personalities. This hypothesis was fully confirmed by the empirical
study conducted by this research except for the demographic factor
where only the educators’ grade or class was found to be associated
with the personality of educators.
Abstract: This paper is devoted to the study of a viscous
incompressible flow around a circular cylinder performing harmonic
oscillations, especially the steady streaming phenomenon. The
research methodology is based on the asymptotic explanation method
combined with the computational bifurcation analysis. The research
approach develops Schlichting and Wang decomposition method.
Present studies allow to identify several regimes of the secondary
streaming with different flow structures. The results of the research
are in good agreement with experimental and numerical simulation
data.
Abstract: The paper deals with current issues in research of
advanced methods to increase reliability of traditional timber
structural elements. It analyses the issue of strengthening of bent
timber beams, such as ceiling beams in old (historical) buildings with
additional concrete slab in combination with externally bonded fibre -
reinforced polymer. The paper describes experimental testing of
composite timber-concrete beam with FRP reinforcement and
compares results with FEM analysis.
Abstract: Well-designed composite steel and concrete structures
highlight the good material properties and lower the deficiencies of
steel and concrete, in particular they make use of high tensile strength
of steel and high stiffness of concrete. The most common composite
steel and concrete structure is a simply supported beam, which
concrete slab transferring the slab load to a beam is connected to the
steel cross-section. The aim of this paper is to find the most adequate
numerical model of a simply supported composite beam with the
cross-sectional and material parameters based on the results of a
processed parametric study and numerical analysis. The paper also
evaluates the suitability of using compact concrete with the
lightweight aggregates for composite steel and concrete beams. The
most adequate numerical model will be used in the resent future to
compare the results of laboratory tests.
Abstract: The purpose of this research is to study of consumer
perception and understanding consumer buying behavior that related
between satisfied and factors affecting the purchasing. Methodology
can be classified between qualitative and quantitative approaches for
the qualitative research were interviews from middlemen who bought
organic vegetables, and middlemen related to production and
marketing system. A questionnaire was utilized as a tool to collect
data. Statistics utilized in this research included frequency,
percentage, mean, standard deviation, and multiple regression
analysis. The result show the reason to decision buying motives is
Fresh products of organic vegetables is the most significant factor on
individuals’ income, with a b of –.143, t = –2.470, the price of
organic vegetables is the most significant factor on individuals’
income, with a b of .176, t = 2.561, p value = .011. The results show
that most people with higher income think about the organic products
are expensive and have negative attitudes towards organic vegetable
as individuals with low and medium income level. Therefore,
household income had a significant influence on the purchasing
decision.
Abstract: The discarded clam shell waste, fossil and edible oil
as biolubricant feedstocks create environmental impacts and food
chain dilemma, thus this work aims to circumvent these issues by
using activated saltwater clam shell waste (SCSW) as solid catalyst
for conversion of Jatropha curcas oil as non-edible sources to ester
biolubricant. The characterization of solid catalyst was done by
Differential Thermal Analysis-Thermo Gravimetric Analysis (DTATGA),
X-Ray Fluorescence (XRF), X-Ray Diffraction (XRD),
Brunauer-Emmett-Teller (BET), Field Emission Scanning Electron
Microscopy (FESEM) and Fourier Transformed Infrared
Spectroscopy (FTIR) analysis. The calcined catalyst was used in the
transesterification of Jatropha oil to methyl ester as the first step, and
the second stage was involved the reaction of Jatropha methyl ester
(JME) with trimethylolpropane (TMP) based on the various process
parameters. The formated biolubricant was analyzed using the
capillary column (DB-5HT) equipped Gas Chromatography (GC).
The conversion results of Jatropha oil to ester biolubricant can be
found nearly 96.66%, and the maximum distribution composition
mainly contains 72.3% of triester (TE).