Abstract: The research presented in this paper has been focused
on analysing the impact of traffic on the sustainable development of
tourism in Croatia's Dubrovacko-Neretvanska County by the year
2020, based on the figures and trends reported in 2014 and using the
relevant variables that characterise the synergy of traffic and tourism
in, speaking from the geographic viewpoint, the most problematic
county in the Republic of Croatia. The basic hypothesis has been
confirmed through scientifically obtained research results, through
the quantification of the model's variables and the direct growth rates
of the designed model. On the basis of scientific insights into the
sustainable development of traffic and tourism in Dubrovacko-
Neretvanska County, it is possible to propose a new information
model for traffic at the service of the sustainable development of
tourism in the County for the period 2014-2020.
Abstract: Vegetation affects the mean and turbulent flow
structure. It may increase flood risks and sediment transport.
Therefore, it is important to develop analytical approaches for the bed
shear stress on vegetated bed, to predict resistance caused by
vegetation. In the recent years, experimental and numerical models
have both been developed to model the effects of submerged
vegetation on open-channel flow. In this paper, different analytic
models are compared and tested using the criteria of deviation, to
explore their capacity for predicting the mean velocity and select the
suitable one that will be applied in real case of rivers. The
comparison between the measured data in vegetated flume and
simulated mean velocities indicated, a good performance, in the case
of rigid vegetation, whereas, Huthoff model shows the best
agreement with a high coefficient of determination (R2=80%) and the
smallest error in the prediction of the average velocities.
Abstract: The California Bearing Ratio (CBR) has been
acknowledged as an important parameter to characterize the bearing
capacity of earth structures, such as earth dams, road embankments,
airport runways, bridge abutments and pavements. Technically, the
CBR test can be carried out in the laboratory or in the field. The CBR
test is time-consuming and is infrequently performed due to the
equipment needed and the fact that the field moisture content keeps
changing over time. Over the years, many correlations have been
developed for the prediction of CBR by various researchers,
including the dynamic cone penetrometer, undrained shear strength
and Clegg impact hammer. This paper reports and discusses some of
the results from a study on the prediction of CBR. In the current
study, the CBR test was performed in the laboratory on some finegrained
subgrade soils collected from various locations in Victoria.
Based on the test results, a satisfactory empirical correlation was
found between the CBR and the physical properties of the
experimental soils.
Abstract: Water contamination by toxic compound is one of the serious environmental problems today. These toxic compounds mostly originated from industrial effluents, agriculture, natural sources and human waste. These studies focus on modification of multiwalled carbon nanotube (MWCNTs) with nanoparticle of calixarene and explore the possibility of using this modification for the remediation of cadmium in water. The nanocomposites were prepared by dissolving calixarene in chloroform solution as solvent, followed by additional multiwalled carbon nanotube (MWCNTs) then sonication process for 3 hour and fabricated the nanocomposites on substrate by spin coating method. Finally, the nanocomposites were tested on cadmium ion (10 mg/ml). The morphology of nanocomposites was investigated by FESEM showing the formation of calixarene on the outer walls of carbon nanotube and cadmium ion also clearly seen from the micrograph. This formation was supported by using energy dispersive x-ray (EDX). The presence of cadmium ions in the films, leads to some changes in the surface potential and Fourier Transform Infrared spectroscopy (FTIR).The nanocomposites MWCNTs-calixarene have potential for development of sensor for pollutant monitoring and nanoelectronics devices applications.
Abstract: In this report we have discussed the theoretical aspects
of the flow transformation, occurring through a series of bifurcations.
The parameters and their continuous diversion, the intermittent bursts
in the transition zone, variation of velocity and pressure with time,
effect of roughness in turbulent zone, and changes in friction factor
and head loss coefficient as a function of Reynolds number for a
transverse flow across a cylinder have been discussed. An analysis of
the variation in the wake length with Reynolds number was done in
FORTRAN.
Abstract: Iris codes contain bits with different entropy. This
work investigates different strategies to reduce the size of iris
code templates with the aim of reducing storage requirements and
computational demand in the matching process. Besides simple subsampling
schemes, also a binary multi-resolution representation as
used in the JBIG hierarchical coding mode is assessed. We find that
iris code template size can be reduced significantly while maintaining
recognition accuracy. Besides, we propose a two-stage identification
approach, using small-sized iris code templates in a pre-selection
stage, and full resolution templates for final identification, which
shows promising recognition behaviour.
Abstract: The paper deals with the usage of speech acts and
politeness strategies in an EFL classroom in Georgia (Rep of). It
explores the students’ and the teachers’ practice of the politeness
strategies and the speech acts of apology, thanking, request,
compliment / encouragement, command, agreeing / disagreeing,
addressing and code switching. The research method includes
observation as well as a questionnaire. The target group involves the
students from Georgian public schools and two certified, experienced
local English teachers. The analysis is based on Searle’s Speech Act
Theory and Brown and Levinson’s politeness strategies. The findings
show that the students have certain knowledge regarding politeness
yet they fail to apply them in English communication. In addition,
most of the speech acts from the classroom interaction are used by
the teachers and not the students. Thereby, it is suggested that
teachers should cultivate the students’ communicative competence
and attempt to give them opportunities to practise more English
speech acts than they do today.
Abstract: This article is to review and understand the new
generation of students to understand their expectations and attitudes.
There are a group of students on school projects, creative work,
educational software and digital signal source, the use of social
networking tools to communicate with friends and a part in the
competition. Today's students have been described as the new
millennium students. They use information and communication
technology in a more creative and innovative at home than at school,
because the information and communication technologies for
different purposes, in the home, usually occur in school. They
collaborate and communicate more effectively when they are at
home. Most children enter school, they will bring about how to use
information and communication technologies, some basic skills and
some tips on how to use information and communication technology
will provide a more advanced than most of the school's expectations.
Many teachers can help students, however, still a lot of work,
"tradition", without a computer, and did not see the "new social
computing networks describe young people to learn and new ways of
working life in the future", in the education system of the benefits of
using a computer.
Abstract: Background: With the perceived pain and poor
function experienced following knee arthroplasty, patients usually
feel un-satisfied. Yet, a controversy still persists on the appropriate
operative technique that doesn’t affect proprioception much.
Purpose: This study compared the effects of Cruciate Retaining
(CR) and Posterior Stabilized (PS) total knee arthroplasty (TKA on
dynamic balance, pain and functional performance following
rehabilitation.
Methods: Thirty patients with CRTKA (group I), thirty with
PSTKA (group II) and fifteen indicated for arthroplasty but weren’t
operated on yet (group III) participated in the study. The mean age
was 54.53±3.44, 55.13±3.48 and 55.33±2.32 years and BMI
35.7±3.03, 35.7±1.99 and 35.73±1.03 kg/m2 for groups I, II and III
respectively. The Berg Balance Scale (BBS), WOMAC pain subscale
and Timed Up-and-Go (TUG) and Stair-Climbing (SC) tests were
used for assessment. Assessments were conducted four weeks preand
post-operatively, three, six and twelve months post-operatively
with the control group being assessed at the same time intervals. The
post-operative rehabilitation involved hospitalization (1st week),
home-based (2nd-4th weeks), and outpatient clinic (5th-12th weeks)
programs, follow-up to all groups for twelve months.
Results: The Mixed design MANOVA revealed that group I had
significantly lower pain scores and SC time compared with group II
three, six and twelve months post-operatively. Moreover, the BBS
scores increased significantly and the pain scores and TUG and SC
time decreased significantly six months post-operatively compared
with four weeks pre- and post-operatively and three months postoperatively
in groups I and II with the opposite being true four weeks
post-operatively. But no significant differences in BBS scores, pain
scores and TUG and SC time between six and twelve months postoperatively
in groups I and II.
Interpretation/Conclusion: CRTKA is preferable to PSTKA,
possibly due to the preserved human proprioceptors in the un-excised
PCL.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: In orthopedic surgery there are various situations in
which the surgeon needs to implement methods of cutting and
drilling the bone. With this type of procedure the generated friction
leads to a localized increase in temperature, which may lead to the
bone necrosis. Recognizing the importance of studying this
phenomenon, an experimental evaluation of the temperatures
developed during the procedure of drilling bone has been done.
Additionally the influence of the use of the procedure with / without
additional lubrication during drilling of bone has also been done. The
obtained results are presented and discussed and suggests an
advantage in using additional lubrication as a way to minimize the
appearance of bone tissue necrosis during bone drilling procedures.
Abstract: This paper presents a novel fractal antenna structure
proposed for UWB (Ultra – Wideband) applications. The frequency
band 3.1-10.6GHz released by FCC (Federal Communication
Commission) as the commercial operation of UWB has been chosen
as frequency range for this antenna based on coplanar waveguide
(CPW) feed and circular shapes fulfilled according to fractal
geometry. The proposed antenna is validated and designed by using
an FR4 substrate with overall area of 34x43 mm2. The simulated
results performed by CST-Microwave Studio and compared by ADS
(Advanced Design System) show good matching input impedance
with return loss less than -10dB between 2.9 GHz and 11 GHz.
Abstract: In this paper we consider the rule reduct generation
problem. Rule Reduct Generation (RG) and Modified Rule
Generation (MRG) algorithms, that are used to solve this problem,
are well-known. Alternative to these algorithms, we develop Pruning
Rule Generation (PRG) algorithm. We compare the PRG algorithm
with RG and MRG.
Abstract: There is an evident trend to elevate pressure ratio of a
single stage of a turbo compressors - axial compressors in particular.
Whilst there was an opinion recently that a pressure ratio 1,9 was a
reasonable limit, later appeared information on successful modeling
tested of stages with pressure ratio up to 2,8. The authors recon that
lack of information on high pressure stages makes actual a study of
rational choice of design parameters before high supersonic flow
problems solving. The computer program of an engineering type was
developed. Below is presented a sample of its application to study
possible parameters of the impeller of the stage with pressure ratio
3,0. Influence of two main design parameters on expected efficiency,
periphery blade speed and flow structure is demonstrated. The results
had lead to choose a variant for further analysis and improvement by
CFD methods.
Abstract: Many organizations bring e-Learning to use as a tool
in their training and human development department. It is getting
more popular because it is easy to access to get knowledge all the
time and also it provides a rich content, which can develop the
employees’ skill efficiently. This study is focused on the factors that
affect using e-Learning efficiently, so it will make job satisfaction
increasing. The questionnaires were sent to employees in large
commercial banks, which use e-Learning located in Bangkok, the
results from multiple linear regression analysis showed that
employee’s characteristics, characteristics of e-Learning, learning and
growth have influence on job satisfaction.
Abstract: Vancron 40, a nitrided powder metallurgical tool
Steel, is used in cold work applications where the predominant failure
mechanisms are adhesive wear or galling. Typical applications of
Vancron 40 are among others fine blanking, cold extrusion, deep
drawing and cold work rolls for cluster mills. Vancron 40 positive
results for cold work rolls for cluster mills and as a tool for some
severe metal forming process makes it competitive compared to other
type of work rolls that require higher precision, among others in cold
rolling of thin stainless steel, which required high surface finish
quality. In this project, three roll materials for cold rolling of stainless
steel strip was examined, Vancron 40, Narva 12B (a high-carbon,
high-chromium tool steel alloyed with tungsten) and Supra 3 (a
Chromium-molybdenum tungsten-vanadium alloyed high speed
steel). The purpose of this project was to study the depth profiles of
the ironed stainless steel strips, emergence of galling and to study the
lubrication performance used by steel industries. Laboratory
experiments were conducted to examine scratch of the strip, galling
and surface roughness of the roll materials under severe tribological
conditions. The critical sliding length for onset of galling was
estimated for stainless steel with four different lubricants. Laboratory
experiments result of performance evaluation of resistance capability
of rolls toward adhesive wear under severe conditions for low and
high reductions. Vancron 40 in combination with cold rolling
lubricant gave good surface quality, prevents galling of
metal surfaces and good bearing capacity.
Abstract: This paper introduces novel approaches to partitioning
and mapping in terms of model-based embedded multicore system
engineering and further discusses benefits, industrial relevance and
features in common with existing approaches. In order to assess
and evaluate results, both approaches have been applied to a real
industrial application as well as to various prototypical demonstrative
applications, that have been developed and implemented for
different purposes. Evaluations show, that such applications improve
significantly according to performance, energy efficiency, meeting
timing constraints and covering maintaining issues by using
the AMALTHEA platform and the implemented approaches.
Furthermore, the model-based design provides an open, expandable,
platform independent and scalable exchange format between
OEMs, suppliers and developers on different levels. Our proposed
mechanisms provide meaningful multicore system utilization since
load balancing by means of partitioning and mapping is effectively
performed with regard to the modeled systems including hardware,
software, operating system, scheduling, constraints, configuration and
more data.
Abstract: Member States shall establish zones and
agglomerations throughout their territory to assess and manage air
quality in order to comply with European directives.
In Italy decree 155/2010, transposing Directive 2008/50/EC on
ambient air quality and cleaner air for Europe, merged into a single
act the previous provisions on ambient air quality assessment and
management, including those resulting from the implementation of
Directive 2004/107/EC relating to arsenic, cadmium, nickel, mercury
and polycyclic aromatic hydrocarbons in ambient air.
Decree 155/2010 introduced stricter rules for identifying zones on
the basis of the characteristics of the territory in spite of considering
pollution levels, as it was in the past. The implementation of such
new criteria has reduced the great variability of the previous zoning,
leading to a significant reduction of the total number of zones and to
a complete and uniform ambient air quality assessment and
management throughout the Country.
The present document is related to the new zones definition in
Italy according to Decree 155/2010. In particular the paper contains
the description and the analysis of the outcome of zoning and
classification.
Abstract: Physics Education Research (PER) results have shown
that students do not achieve the expected level of competency in
understanding the concepts of different domains of Physics learning
when taught by the traditional teaching methods, the concepts of
Electricity and Magnetism (E&M) being one among them.
Simulation being one of the valuable instructional tools renders an
opportunity to visualize varied experiences with such concepts.
Considering the electric force concept which requires extensive use
of vector representations, we report here the outcome of the research
results pertaining to the student understanding of this concept and the
role of simulation in using vector representation. The simulation
platform provides a positive impact on the use of vector
representation.
The first stage of this study involves eliciting and analyzing
student responses to questions that probe their understanding of the
concept of electrostatic force and this is followed by four stages of
student interviews as they use the interactive simulations of electric
force in one dimension. Student responses to the questions are
recorded in real time using electronic pad. A validation test interview
is conducted to evaluate students' understanding of the electric force
concept after using interactive simulation. Results indicate lack of
procedural knowledge of the vector representation. The study
emphasizes the need for the choice of appropriate simulation and
mode of induction for learning.
Abstract: Company managers are always looking for more and
more opportunities to succeed in today's fiercely competitive market.
To maintain your place among the successful companies on the
market today or to come up with a revolutionary business idea is
much more difficult than before. Each new or improved method, tool,
or approach that can improve the functioning of business processes or
even of the entire system is worth checking and verification. The use
of simulation in the design of manufacturing systems and their
management in practice is one of the ways without increased risk,
which makes it possible to find the optimal parameters of
manufacturing processes and systems. The paper presents an example
of use of simulation for solution of the bottleneck problem in the
concrete company.