Abstract: Void formation in underfill is considered as failure
in flip chip manufacturing process. Void formation possibly caused
by several factors such as poor soldering and flux residue during
die attach process, void entrapment due moisture contamination,
dispense pattern process and setting up the curing process. This
paper presents the comparison of single step and two steps curing
profile towards the void and black dots formation in underfill for
Hi-CTE Flip Chip Ceramic Ball Grid Array Package (FC-CBGA).
Statistic analysis was conducted to analyze how different factors
such as wafer lot, sawing technique, underfill fillet height and
curing profile recipe were affected the formation of voids and
black dots. A C-Mode Scanning Aqoustic Microscopy (C-SAM)
was used to scan the total count of voids and black dots. It was
shown that the 2 steps curing profile provided solution for void
elimination and black dots in underfill after curing process.
Abstract: Micro droplet formation is considered as a growing
emerging area of research due to its wide-range application in
chemistry as well as biology. The mechanism of micro droplet
formation using two immiscible liquids running through a T-junction
has been widely studied.
We believe that the flow of these two immiscible phases can be of
greater important factor that could have an impact on out-flow
hydrodynamic behavior, the droplets generated and the size of the
droplets. In this study, the type of the capillary tubes used also
represents another important factor that can have an impact on the
generation of micro droplets.
The tygon capillary tubing with hydrophilic inner surface doesn't
allow regular out-flows due to the fact that the continuous phase
doesn't adhere to the wall of the capillary inner surface.
Teflon capillary tubing, presents better wettability than tygon
tubing, and allows to obtain steady and regular regimes of out-flow,
and the micro droplets are homogeneoussize.
The size of the droplets is directly dependent on the flows of the
continuous and dispersed phases. Thus, as increasing the flow of the
continuous phase, to flow of the dispersed phase stationary, the size
of the drops decreases. Inversely, while increasing the flow of the
dispersed phase, to flow of the continuous phase stationary, the size
of the droplet increases.
Abstract: The most widely used semiconductor memory types
are the Dynamic Random Access Memory (DRAM) and Static
Random Access memory (SRAM). Competition among memory
manufacturers drives the need to decrease power consumption and
reduce the probability of read failure. A technology that is relatively
new and has not been explored is the FinFET technology. In this
paper, a single cell Schmitt Trigger Based Static RAM using FinFET
technology is proposed and analyzed. The accuracy of the result is
validated by means of HSPICE simulations with 32nm FinFET
technology and the results are then compared with 6T SRAM using
the same technology.
Abstract: Existing experiences indicate that one of the most
prominent reasons that some ERP implementations fail is related to
selecting an improper ERP package. Among those important factors
resulting in inappropriate ERP selections, one is to ignore preliminary
activities that should be done before the evaluation of ERP packages.
Another factor yielding these unsuitable selections is that usually
organizations employ prolonged and costly selection processes in
such extent that sometimes the process would never be finalized
or sometimes the evaluation team might perform many key final
activities in an incomplete or inaccurate way due to exhaustion, lack
of interest or out-of-date data. In this paper, a systematic approach
that recommends some activities to be done before and after the
main selection phase is introduced for choosing an ERP package. On
the other hand, the proposed approach has utilized some ideas that
accelerates the selection process at the same time that reduces the
probability of an erroneous final selection.
Abstract: This paper presents a vocoder to obtain high quality synthetic speech at 600 bps. To reduce the bit rate, the algorithm is based on a sinusoidally excited linear prediction model which extracts few coding parameters, and three consecutive frames are grouped into a superframe and jointly vector quantization is used to obtain high coding efficiency. The inter-frame redundancy is exploited with distinct quantization schemes for different unvoiced/voiced frame combinations in the superframe. Experimental results show that the quality of the proposed coder is better than that of 2.4kbps LPC10e and achieves approximately the same as that of 2.4kbps MELP and with high robustness.
Abstract: Despite the extensive use of eLearning systems, there
is no consensus on a standard framework for evaluating this kind of
quality system. Hence, there is only a minimum set of tools that can
supervise this judgment and gives information about the course
content value. This paper presents two kinds of quality set evaluation
indicators for eLearning courses based on the computational process
of three known metrics, the Euclidian, Hamming and Levenshtein
distances. The “distance" calculus is applied to standard evaluation
templates (i.e. the European Commission Programme procedures vs.
the AFNOR Z 76-001 Standard), determining a reference point in the
evaluation of the e-learning course quality vs. the optimal concept(s).
The case study, based on the results of project(s) developed in the
framework of the European Programme “Leonardo da Vinci", with
Romanian contractors, try to put into evidence the benefits of such a
method.
Abstract: During the last few decades in the academic field, the
debate has increased on the effects of social geography on the
opportunities of socioeconomic integration. On one hand, it has been
discussed how the contents of the urban structure and social
geography affect not only the way people interact, but also their
chances of social and economic integration. On the other hand, it has
also been discussed how the urban structure is also constrained and
transformed by the action of social actors. Without questioning the
powerful influence of structural factors, related to the logic of the
production system, labor markets, education and training, the
research has shown the role played by place of residence in shaping
individual outcomes such as unemployment. In the context of this
debate the importance of territory of residence with respect to the
problem of unemployment has been highlighted.
Although statistics of unemployment have already demonstrated
the unequal incidence of the phenomenon in social groups, the issue
of uneven territorial impact on the phenomenon at intra-urban level
remains relatively unknown.
The purpose of this article is to show and to interpret the spatial
patterns of unemployment in the city of Porto using GIS (Geographic
Information System - GIS) technology. Under this analysis the
overlap of the spatial patterns of unemployment with the spatial
distribution of social housing, allows the discussion of the
relationship that occurs between these patterns and the reasons that
might explain the relative immutability of socioeconomic problems in
some neighborhoods.
Abstract: The objective of this paper is to present a research
study of the convectors that are used for heating or cooling of the
living room or industrial halls. The key points are experimental
measurement and comprehensive numerical simulation of the flow
coming throughout the part of the convector such as heat exchanger,
input from the fan etc.. From the obtained results, the components of
the convector are optimized in sense to increase thermal power
efficiency due to improvement of heat convection or reduction of air
drag friction. Both optimized aspects are leading to the more
effective service conditions and to energy saving. The significant part
of the convector research is a design of the unique measurement
laboratory and adopting measure techniques. The new laboratory
provides possibility to measure thermal power efficiency and other
relevant parameters under specific service conditions of the
convectors.
Abstract: Semiconductor detector arrays are widely used in
high-temperature plasma diagnostics. They have a fast response,
which allows observation of many processes and instabilities in
tokamaks. In this paper, there are reviewed several diagnostics based
on semiconductor arrays as cameras, AXUV photodiodes (referred
often as fast “bolometers") and detectors of both soft X-rays and
visible light installed on the COMPASS tokamak recently. Fresh
results from both spring and summer campaigns in 2012 are
introduced. Examples of the utilization of the detectors are shown on
the plasma shape determination, fast calculation of the radiation
center, two-dimensional plasma radiation tomography in different
spectral ranges, observation of impurity inflow, and also on
investigation of MHD activity in the COMPASS tokamak discharges.
Abstract: Thailand-s health system is challenged by the rising
number of patients and decreasing ratio of medical
practitioners/patients, especially in rural areas. This may tempt
inexperienced GPs to rush through the process of anamnesis with the
risk of incorrect diagnosis. Patients have to travel far to the hospital
and wait for a long time presenting their case. Many patients try to
cure themselves with traditional Thai medicine. Many countries are
making use of the Internet for medical information gathering,
distribution and storage. Telemedicine applications are a relatively
new field of study in Thailand; the infrastructure of ICT had
hampered widespread use of the Internet for using medical
information. With recent improvements made health and technology
professionals can work out novel applications and systems to help
advance telemedicine for the benefit of the people. Here we explore
the use of telemedicine for people with health problems in rural areas
in Thailand and present a Telemedicine Diagnosis System for Rural
Thailand (TEDIST) for diagnosing certain conditions that people
with Internet access can use to establish contact with Community
Health Centers, e.g. by mobile phone. The system uses a Web-based
input method for individual patients- symptoms, which are taken by
an expert system for the analysis of conditions and appropriate
diseases. The analysis harnesses a knowledge base and a backward
chaining component to find out, which health professionals should be
presented with the case. Doctors have the opportunity to exchange
emails or chat with the patients they are responsible for or other
specialists. Patients- data are then stored in a Personal Health Record.
Abstract: Based on a global kinetics of direct dimethyl ether (DME) synthesis process from syngas, a steady-state one-dimensional mathematical model for the bubble column slurry reactor (BCSR) has been established. It was built on the assumption of plug flow of gas phase, sedimentation-dispersion model of catalyst grains and isothermal chamber regardless of reaction heats and rates for the design of an industrial scale bubble column slurry reactor. The simulation results indicate that higher pressure and lower temperature were favorable to the increase of CO conversion, DME selectivity, products yield and the height of slurry bed, which has a coincidence with the characteristic of DME synthesis reaction system, and that the height of slurry bed is lessen with the increasing of operation temperature in the range of 220-260℃. CO conversion, the optimal operation conditions in BCSR were proposed.
Abstract: For broadband wireless mobile communication
systems the orthogonal frequency division multiplexing (OFDM) is a
suitable modulation scheme. The frequency offset between
transmitter and receiver local oscillator is main drawback of OFDM
systems, which causes intercarrier interference (ICI) in the
subcarriers of the OFDM system. This ICI degrades the bit error rate
(BER) performance of the system. In this paper an improved self-ICI
cancellation scheme is proposed to improve the system performance.
The proposed scheme is based on discrete Fourier transform-inverse
discrete Fourier transform (DFT-IDFT). The simulation results show
that there is satisfactory improvement in the bit error rate (BER)
performance of the present scheme.
Abstract: Variations in the growth rate constant of the Listeria
monocytogenes bacterial species were determined at 37°C in
irradiated environments and compared to the situation of a nonirradiated
environment. The bacteria cells, contained in a suspension
made of a nutrient solution of Brain Heart Infusion, were made to
grow at different frequency (2.30e2.60 GHz) and power (0e400
mW) values, in a plug flow reactor positioned in the irradiated
environment. Then the reacting suspension was made to pass into a
cylindrical cuvette where its optical density was read every 2.5
minutes at a wavelength of 600 nm. The obtained experimental data
of optical density vs. time allowed the bacterial growth rate constant
to be derived; this was found to be slightly influenced by microwave
power, but not by microwave frequency; in particular, a minimum
value was found for powers in the 50e150 mW field.
Abstract: The V-notches are most possible case for initiation of cracks in parts. The specifications of cracks on the tip of the notch will be influenced via opening angle, tip radius and depth of V-notch. In this study, the effects of V-notch-s opening angle on stress intensity factor and T-stress of crack on the notch has been investigated. The experiment has been done in different opening angles and various crack length in mode (I) loading using Photoelasticity method. The results illustrate that while angle increases in constant crack-s length, SIF and T-stress will decrease. Beside, the effect of V-notch angle in short crack is more than long crack. These V-notch affects are negligible by increasing the length of crack, and the crack-s behavior can be considered as a single-edge crack specimen. Finally, the results have been evaluated with numerical finite element analysis and good agreement was obvious.
Abstract: Firstly, this study briefly presents the current situation that there exists a vast gap between current Chinese and Japanese seismic design specification for bridge pile foundation in liquefiable and liquefaction-induced lateral spreading ground; The Chinese and Japanese seismic design method and technical detail for bridge pile foundation in liquefying and lateral spreading ground are described and compared systematically and comprehensively, the methods of determining coefficient of subgrade reaction and its reduction factor as well as the computing mode of the applied force on pile foundation due to liquefaction-induced lateral spreading soil in Japanese design specification are especially introduced. Subsequently, the comparison indicates that the content of Chinese seismic design specification for bridge pile foundation in liquefiable and liquefaction-induced lateral spreading ground, just presenting some qualitative items, is too general and lacks systematicness and maneuverability. Finally, some defects of seismic design specification in China are summarized, so the improvement and revision of specification in the field turns out to be imperative for China, some key problems of current Chinese specifications are generalized and the corresponding improvement suggestions are proposed.
Abstract: The speculative locking (SL) protocol extends the twophase locking (2PL) protocol to allow for parallelism among conflicting transactions. The adaptive speculative locking (ASL) protocol provided further enhancements and outperformed SL protocols under most conditions. Neither of these protocols consider the impact of network latency on the performance of the distributed database systems. We have studied the performance of ASL protocol taking into account the communication overhead. The results indicate that though system load can counter network latency, it can still become a bottleneck in many situations. The impact of latency on performance depends on many factors including the system resources. A flexible discrete event simulator was used as the testbed for this study.
Abstract: Number of breakdowns experienced by a machinery is a highly under-dispersed count random variable and its value can be attributed to the factors related to the mechanical input and output of that machinery. Analyzing such under-dispersed count observations as a function of the explanatory factors has been a challenging problem. In this paper, we aim at estimating the effects of various factors on the number of breakdowns experienced by a passenger car based on a study performed in Mauritius over a year. We remark that the number of passenger car breakdowns is highly under-dispersed. These data are therefore modelled and analyzed using Com-Poisson regression model. We use quasi-likelihood estimation approach to estimate the parameters of the model. Under-dispersion parameter is estimated to be 2.14 justifying the appropriateness of Com-Poisson distribution in modelling under-dispersed count responses recorded in this study.
Abstract: In recent years, we see an increase of interest for efficient tracking systems in surveillance applications. Many of the proposed techniques are designed for static cameras environments. When the camera is moving, tracking moving objects become more difficult and many techniques fail to detect and track the desired targets. The problem becomes more complex when we want to track a specific object in real-time using a moving Pan and Tilt camera system to keep the target within the image. This type of tracking is of high importance in surveillance applications. When a target is detected at a certain zone, the possibility of automatically tracking it continuously and keeping it within the image until action is taken is very important for security personnel working in very sensitive sites. This work presents a real-time tracking system permitting the detection and continuous tracking of targets using a Pan and Tilt camera platform. A novel and efficient approach for dealing with occlusions is presented. Also a new intelligent forget factor is introduced in order to take into account target shape variations and avoid learning non desired objects. Tests conducted in outdoor operational scenarios show the efficiency and robustness of the proposed approach.
Abstract: ERP systems are the largest software applications adopted by universities, along with quite significant investments in their implementation. However, unlike other applications little research has been conducted regarding these systems in a university environment. This paper aims at providing a critical review of previous research in ERP system in higher education with a special focus on higher education in Australia. The research not only forms the basis of an evaluation of previous research and research needs, it also makes inroads in identifying the payoff of ERPs in the sector from different perspectives with particular reference to the user. The paper is divided into two parts, the first part focuses on ERP literature in higher education at large, while the second focuses on ERP literature in higher education in Australia.
Abstract: This research investigates the factors that influence moral judgments when dealing with ethical dilemmas in the organizational context. It also investigates the antecedents of individual ethical ideology (idealism and relativism). A mixed method study, which combines qualitative (field study) and quantitative (survey) approaches, was used in this study. An initial model was developed first, which was then fine-tuned based on field studies. Data were collected from managers in Malaysian large organizations. The results of this study reveal that in-group collectivism culture, power distance culture, parental values, and religiosity were significant as antecedents of ethical ideology. However, direct effects of these variables on moral judgment were not significant. Furthermore, the results of this study confirm the significant effects of ethical ideology on moral judgment. This study provides valuable insight into evaluating the validity of existing theory as proposed in the literature and offers significant practical implications.