Abstract: The Radio Frequency Identification (RFID) technology
has a diverse base of applications, but it is also prone to security
threats. There are different types of security attacks which limit the
range of the RFID applications. For example, deploying the RFID
networks in insecure environments could make the RFID system
vulnerable to many types of attacks such as spoofing attack, location
traceability attack, physical attack and many more. Therefore, security
is often an important requirement for RFID systems. In this paper,
RFID mutual authentication protocol is implemented based on mobile
agent technology and timestamp, which are used to provide strong
authentication and integrity assurances to both the RFID readers and
their corresponding RFID tags. The integration of mobile agent
technology and timestamp provides promising results towards
achieving this goal and towards reducing the security threats in RFID
systems.
Abstract: In the present study we have investigated axial
buckling characteristics of nanocomposite beams reinforced by
single-walled carbon nanotubes (SWCNTs). Various types of beam
theories including Euler-Bernoulli beam theory, Timoshenko beam
theory and Reddy beam theory were used to analyze the buckling
behavior of carbon nanotube-reinforced composite beams.
Generalized differential quadrature (GDQ) method was utilized to
discretize the governing differential equations along with four
commonly used boundary conditions. The material properties of the
nanocomposite beams were obtained using molecular dynamic (MD)
simulation corresponding to both short-(10,10) SWCNT and long-
(10,10) SWCNT composites which were embedded by amorphous
polyethylene matrix. Then the results obtained directly from MD
simulations were matched with those calculated by the mixture rule
to extract appropriate values of carbon nanotube efficiency
parameters accounting for the scale-dependent material properties.
The selected numerical results were presented to indicate the
influences of nanotube volume fractions and end supports on the
critical axial buckling loads of nanocomposite beams relevant to
long- and short-nanotube composites.
Abstract: This paper describes a subarray based low
computational design method of multiuser massive multiple
input multiple output (MIMO) system. In our previous works, use of
large array is assumed only in transmitter, but this study considers
the case both of transmitter and receiver sides are equipped with
large array antennas. For this aim, receive arrays are also divided
into several subarrays, and the former proposed method is modified
for the synthesis of a large array from subarrays in both ends.
Through computer simulations, it is verified that the performance
of the proposed method is degraded compared with the original
approach, but it can achieve the improvement in the aspect of
complexity, namely, significant reduction of the computational load
to the practical level.
Abstract: Mineral oil is commonly used for high voltage
transformer insulation. The insulation quality of mineral oil is
affecting the operation process of high voltage transformer. There are
many contaminations which could decrease the insulation quality of
mineral oil. One of them is water. This research talks about the effect
of water content on dielectric properties, physic properties, and
partial discharge pattern on mineral oil. Samples were varied with 10
varieties of water content value. And then all samples would be tested
to measure the dielectric properties, physic properties, and partial
discharge pattern. The result of this research showed that an
increment of water content value would decrease the insulation
quality of mineral oil.
Abstract: Evaluation of the excavation-induced ground
movements is an important design aspect of support systems in urban
areas. Geological and geotechnical conditions of an excavation area
have significant effects on excavation-induced ground movements and
the related damage. This paper is aimed at studying the performance of
excavation walls supported by nails in jointed rock medium. The
performance of nailed walls is investigated based on evaluating the
excavation-induced ground movements. For this purpose, a set of
calibrated 2D finite element models are developed by taking into
account the nail-rock-structure interactions, the anisotropic properties
of jointed rock, and the staged construction process. The results of this
paper highlight effects of different parameters such as joint
inclinations, anisotropy of rocks and nail inclinations on deformation
parameters of excavation wall supported by nails.
Abstract: Clustering is a process of grouping objects and data
into groups of clusters to ensure that data objects from the same
cluster are identical to each other. Clustering algorithms in one of the
area in data mining and it can be classified into partition, hierarchical,
density based and grid based. Therefore, in this paper we do survey
and review four major hierarchical clustering algorithms called
CURE, ROCK, CHAMELEON and BIRCH. The obtained state of
the art of these algorithms will help in eliminating the current
problems as well as deriving more robust and scalable algorithms for
clustering.
Abstract: The knitted fabric suffers a deformation in its
dimensions due to stretching and tension factors, transverse and
longitudinal respectively, during the process in rectilinear knitting
machines so it performs a dry relaxation shrinkage procedure and
thermal action of prefixed to obtain stable conditions in the knitting.
This paper presents a dry relaxation shrinkage prediction of Bordeaux
fiber using a feed forward neural network and linear regression
models. Six operational alternatives of shrinkage were predicted. A
comparison of the results was performed finding neural network
models with higher levels of explanation of the variability and
prediction. The presence of different reposes is included. The models
were obtained through a neural toolbox of Matlab and Minitab
software with real data in a knitting company of Southern
Guanajuato. The results allow predicting dry relaxation shrinkage of
each alternative operation.
Abstract: An analytical 4-DOF nonlinear model of a de Laval
rotor-stator system based on Energy Principles has been used
theoretically and experimentally to investigate fault symptoms in a
rotating system. The faults, namely rotor-stator-rub, crack and
unbalance are modeled as excitations on the rotor shaft. Mayes
steering function is used to simulate the breathing behaviour of the
crack. The fault analysis technique is based on waveform signal,
orbits and Fast Fourier Transform (FFT) derived from simulated and
real measured signals. Simulated and experimental results manifest
considerable mutual resemblance of elliptic-shaped orbits and FFT
for a same range of test data.
Abstract: Nonlinear evolution of broadband ultrasonic pulses
passed through the rock specimens is studied using the apparatus
“GEOSCAN-02M”. Ultrasonic pulses are excited by the pulses of Qswitched
Nd:YAG laser with the time duration of 10 ns and with the
energy of 260 mJ. This energy can be reduced to 20 mJ by some light
filters. The laser beam radius did not exceed 5 mm. As a result of the
absorption of the laser pulse in the special material – the optoacoustic
generator–the pulses of longitudinal ultrasonic waves are excited with
the time duration of 100 ns and with the maximum pressure
amplitude of 10 MPa. The immersion technique is used to measure
the parameters of these ultrasonic pulses passed through a specimen,
the immersion liquid is distilled water. The reference pulse passed
through the cell with water has the compression and the rarefaction
phases. The amplitude of the rarefaction phase is five times lower
than that of the compression phase. The spectral range of the
reference pulse reaches 10 MHz. The cubic-shaped specimens of the
Karelian gabbro are studied with the rib length 3 cm. The ultimate
strength of the specimens by the uniaxial compression is (300±10)
MPa. As the reference pulse passes through the area of the specimen
without cracks the compression phase decreases and the rarefaction
one increases due to diffraction and scattering of ultrasound, so the
ratio of these phases becomes 2.3:1. After preloading some horizontal
cracks appear in the specimens. Their location is found by one-sided
scanning of the specimen using the backward mode detection of the
ultrasonic pulses reflected from the structure defects. Using the
computer processing of these signals the images are obtained of the
cross-sections of the specimens with cracks. By the increase of the
reference pulse amplitude from 0.1 MPa to 5 MPa the nonlinear
transformation of the ultrasonic pulse passed through the specimen
with horizontal cracks results in the decrease by 2.5 times of the
amplitude of the rarefaction phase and in the increase of its duration
by 2.1 times. By the increase of the reference pulse amplitude from 5
MPa to 10 MPa the time splitting of the phases is observed for the
bipolar pulse passed through the specimen. The compression and
rarefaction phases propagate with different velocities. These features
of the powerful broadband ultrasonic pulses passed through the rock
specimens can be described by the hysteresis model of Preisach-
Mayergoyz and can be used for the location of cracks in the optically
opaque materials.
Abstract: The hydrodynamic and thermal behaviors of fluid
flow in wavy microchannel are investigated numerically. Effects of
Reynolds number on the hydrodynamics and thermal behaviors are
investigated. Three cases of Reynolds number (580, 1244, and 1910)
are adopted in this study. It is found that the separation zone begin
appears when Reynolds number is greater than 1910 at the endsection
of the wave. Also it is found that dimensionless maximum
velocity at the mid-section of the wave decreases and becomes as a
turbulent behavior as Reynolds numbers increases. The maximum
temperature at the center line at the mid-section of the wave increases
as Reynolds number increases until it reaches the turbulent behavior
when Reynolds number is equal or greater than 1244, while this
behavior will be achieved at very high velocities at the end section of
the wave.
Abstract: Si-Ge solid solutions (bulk poly- and mono-crystalline
samples, thin films) are characterized by high perspectives for
application in semiconductor devices, in particular, optoelectronics
and microelectronics. From this point of view, complex studying of
structural state of the defects and structural-sensitive physical
properties of Si-Ge solid solutions depending on the contents of Si
and Ge components is very important. Present work deals with the
investigations of microstructure, microhardness, internal friction and
shear modulus of Si1-xGex(x≤0,02) bulk monocrystals conducted at
room temperature. Si-Ge bulk crystals were obtained by Czochralski
method in [111] crystallographic direction. Investigated
monocrystalline Si-Ge samples are characterized by p-type
conductivity and carriers’ concentration 5.1014-1.1015cm-3.
Microhardness was studied on Dynamic Ultra Micro hardness Tester
DUH-201S with Berkovich indenter. Investigate samples are characterized with 0,5x0,5x(10-15)mm3
sizes, oriented along [111] direction at torsion oscillations ≈1Hz,
multistage changing of internal friction and shear modulus has been
revealed in an interval of strain amplitude of 10-5-5.10-3. Critical
values of strain amplitude have been determined at which hysteretic
changes of inelastic characteristics and microplasticity are observed. The critical strain amplitude and elasticity limit values are also
determined. Dynamic mechanical characteristics decreasing trend is
shown with increasing Ge content in Si-Ge solid solutions. Observed
changes are discussed from the point of view of interaction of various
dislocations with point defects and their complexes in a real structure
of Si-Ge solid solutions.
Abstract: Research has shown that techno-entrepreneurship is
economically significant. Therefore, it is suggested that teaching
techno-entrepreneurship may be important because such programmes
would prepare current and future generations of learners to recognise
and act on high-technology opportunities. Education in technoentrepreneurship
may increase the knowledge of how to start one’s
own enterprise and recognise the technological opportunities for
commercialisation to improve decision-making about starting a new
venture; also it influence decisions about capturing the business
opportunities and turning them into successful ventures. Universities
can play a main role in connecting and networking technoentrepreneurship
students towards a cooperative attitude with real
business practice and industry knowledge. To investigate and answer
whether education for techno-entrepreneurs really helps, this paper
choses a comparison of literature reviews as its method of research.
After reviewing literature related to the impact of technoentrepreneurship
education on self-employment 6 studies which had
similar aim and objective to this paper were. These particular papers
were selected based on a keywords search and as their aim,
objectives, and gaps were close to the current research. In addition,
they were all based on the influence of techno-entrepreneurship
education in self-employment and intention of students to start new
ventures. The findings showed that teaching techno-entrepreneurship
education may have an influence on students’ intention and their
future self-employment, but which courses should be covered and the
duration of programmes, needs further investigation.
Abstract: The need to merge software artifacts seems inherent
to modern software development. Distribution of development over
several teams and breaking tasks into smaller, more manageable
pieces are an effective means to deal with the kind of complexity. In
each case, the separately developed artifacts need to be assembled as
efficiently as possible into a consistent whole in which the parts still
function as described. In addition, earlier changes are introduced into
the life cycle and easier is their management by designers.
Interaction-based specifications such as UML sequence diagrams
have been found effective in this regard. As a result, sequence
diagrams can be used not only for capturing system behaviors but
also for merging changes in order to create a new version. The
objective of this paper is to suggest a new approach to deal with the
problem of software merging at the level of sequence diagrams by
using the concept of dependence analysis that captures, formally, all
mapping, and differences between elements of sequence diagrams
and serves as a key concept to create a new version of sequence
diagram.
Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: Heart is the most important part in the body of living
organisms. It affects and is affected by any factor in the body.
Therefore, it is a good detector for all conditions in the body. Heart
signal is a non-stationary signal; thus, it is utmost important to study
the variability of heart signal. The Heart Rate Variability (HRV) has
attracted considerable attention in psychology, medicine and has
become important dependent measure in psychophysiology and
behavioral medicine. The standards of measurements, physiological
interpretation and clinical use for HRV that are most often used were
described in many researcher papers, however, remain complex
issues are fraught with pitfalls. This paper presents one of the nonlinear
techniques to analyze HRV. It discusses many points like, what
Poincaré plot is and how Poincaré plot works; also, Poincaré plot's
merits especially in HRV. Besides, it discusses the limitation of
Poincaré cause of standard deviation SD1, SD2 and how to overcome
this limitation by using complex correlation measure (CCM). The
CCM is most sensitive to changes in temporal structure of the
Poincaré plot as compared toSD1 and SD2.
Abstract: This research was conducted in an automotive company in Indonesia to overcome the problem of high logistics cost. The problem causes high of additional truck delivery. From the breakdown of the problem, chosen one route, which has the highest gap value, namely for RE-04. Research methodology will be started from calculating the ideal condition, making simulation, calculating the ideal logistic cost, and proposing an improvement. From the calculation of the ideal condition, box arrangement was done on the truck has efficiency with three trucks delivery per day. Route simulation making uses Tecnomatix Plant Simulation software as a visualization for the company about how the system is occurred on route RE-04 in ideal condition. The last step is proposing improvements on the area of route RE-04. The route arrangement is done by Saving Method and sequence of each supplier with the Nearest Neighbor. The results of the proposed improvements are three new route groups, where was expected to decrease logistics cost and increase the average of the truck efficiency per day.
Abstract: The effect of molybdate addition to chloride
environment on resistance of AISI 316Ti stainless steel to pitting
corrosion was studied. Potentiodynamic polarisation tests were
performed in 1 M and 0.1 M chloride acidified solutions with various
additions of sodium molybdate at room temperature. The presented
results compare the effect of molybdate anions on quality of passive
film (expressed by the pitting potential) in both chloride solutions.
The pitting potential increases with the increase inhibitor
concentration. The inhibitive effect of molybdate ions is stronger in
chloride solution of lower aggressiveness (0.1M).
Abstract: Ocean current is always available around the
surrounding of SHELL Sabah Water Platform and data are collected
every 10 minutes, 24 hours a day, for a period of 365 days. Due to
low current speed, conventional hydrokinetic power generation is not
feasible, thus leading to the study of low current enabled vortex
induced vibration power generation application. In this case, the
design of a vortex induced vibration application is studied to obtain
an optimum design for the VIV oscillator. Power output is then
determined to study the feasibility of the VIV application in low
current condition.
Abstract: Due to the fast and flawless technological innovation
there is a tremendous amount of data dumping all over the world in
every domain such as Pattern Recognition, Machine Learning, Spatial
Data Mining, Image Analysis, Fraudulent Analysis, World Wide
Web etc., This issue turns to be more essential for developing several
tools for data mining functionalities. The major aim of this paper is to
analyze various tools which are used to build a resourceful analytical
or descriptive model for handling large amount of information more
efficiently and user friendly. In this survey the diverse tools are
illustrated with their extensive technical paradigm, outstanding
graphical interface and inbuilt multipath algorithms in which it is
very useful for handling significant amount of data more indeed.
Abstract: This paper studies a mathematical model based on the
integral equations for dynamic analyzes numerical investigations of a
non-uniform or multi-material composite beam. The beam is
subjected to a sub-tangential follower force and elastic foundation.
The boundary conditions are represented by generalized
parameterized fixations by the linear and rotary springs. A
mathematical formula based on Euler-Bernoulli beam theory is
presented for beams with variable cross-sections. The non-uniform
section introduces non-uniformity in the rigidity and inertia of beams
and consequently, more complicated equilibrium who governs the
equation. Using the boundary element method and radial basis
functions, the equation of motion is reduced to an algebro-differential
system related to internal and boundary unknowns. A generalized
formula for the deflection, the slope, the moment and the shear force
are presented. The free vibration of non-uniform loaded beams is
formulated in a compact matrix form and all needed matrices are
explicitly given. The dynamic stability analysis of slender beam is
illustrated numerically based on the coalescence criterion. A realistic
case related to an industrial chimney is investigated.