Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.
Abstract: The objective of this paper is to a design of pattern
classification model based on the back-propagation (BP) algorithm for
decision support system. Standard BP model has done full connection
of each node in the layers from input to output layers. Therefore, it
takes a lot of computing time and iteration computing for good
performance and less accepted error rate when we are doing some
pattern generation or training the network.
However, this model is using exclusive connection in between
hidden layer nodes and output nodes. The advantage of this model is
less number of iteration and better performance compare with standard
back-propagation model. We simulated some cases of classification
data and different setting of network factors (e.g. hidden layer number
and nodes, number of classification and iteration). During our
simulation, we found that most of simulations cases were satisfied by
BP based using exclusive connection network model compared to
standard BP. We expect that this algorithm can be available to
identification of user face, analysis of data, mapping data in between
environment data and information.
Abstract: Atmospheric stability plays the most important role in
the transport and dispersion of air pollutants. Different methods are
used for stability determination with varying degrees of complexity.
Most of these methods are based on the relative magnitude of
convective and mechanical turbulence in atmospheric motions.
Richardson number, Monin-Obukhov length, Pasquill-Gifford
stability classification and Pasquill–Turner stability classification, are
the most common parameters and methods. The Pasquill–Turner
Method (PTM), which is employed in this study, makes use of
observations of wind speed, insolation and the time of day to classify
atmospheric stability with distinguishable indices. In this study, a
model is presented to determination of atmospheric stability
conditions using PTM. As a case study, meteorological data of
Mehrabad station in Tehran from 2000 to 2005 is applied to model.
Here, three different categories are considered to deduce the pattern
of stability conditions. First, the total pattern of stability classification
is obtained and results show that atmosphere is 38.77%, 27.26%,
33.97%, at stable, neutral and unstable condition, respectively. It is
also observed that days are mostly unstable (66.50%) while nights are
mostly stable (72.55%). Second, monthly and seasonal patterns are
derived and results indicate that relative frequency of stable
conditions decrease during January to June and increase during June
to December, while results for unstable conditions are exactly in
opposite manner. Autumn is the most stable season with relative
frequency of 50.69% for stable condition, whilst, it is 42.79%,
34.38% and 27.08% for winter, summer and spring, respectively.
Hourly stability pattern is the third category that points out that
unstable condition is dominant from approximately 03-15 GTM and
04-12 GTM for warm and cold seasons, respectively. Finally,
correlation between atmospheric stability and CO concentration is
achieved.
Abstract: This experiment discusses the effects of fracture
parameters such as depth, length, width, angle and the number of the
fracture to the conductance properties of laterite using the DUK-2B
digital electrical measurement system combined with the method of
simulating the fractures. The results of experiment show that the
changes of fracture parameters produce effects to the conductance
properties of laterite. There is a clear degressive period of the
conductivity of laterite during increasing the depth, length, width, or
the angle and the quantity of fracture gradually. When the depth of
fracture exceeds the half thickness of the soil body, the conductivity of
laterite shows evidently non-linear diminishing pattern and the
amplitude of decrease tends to increase. The length of fracture has
fewer effects than the depth to the conductivity. When the width of
fracture reaches some fixed values, the change of the conductivity is
less sensitive to the change of the width, and at this time, the
conductivity of laterite maintains at a stable level. When the angle of
fracture is less than 45°, the decrease of the conductivity is more
clearly as the angle increases. But when angle is more than 45°,
change of the conductivity is relatively gentle as the angle increases.
The increasing quantity of the fracture causes the other fracture
parameters having great impact on the change of conductivity. When
moisture content and temperature were unchanged, depth and angle of
fractures are the major factors affecting the conductivity of laterite
soil; quantity, length, and width are minor influencing factors. The
sensitivity of fracture parameters affect conductivity of laterite soil is:
depth >angles >quantity >length >width.
Abstract: This paper presents anapproach of hybridizing two or more artificial intelligence (AI) techniques which arebeing used to
fuzzify the workstress level ranking and categorize the rating accordingly. The use of two or more techniques (hybrid approach)
has been considered in this case, as combining different techniques may lead to neutralizing each other-s weaknesses generating a
superior hybrid solution. Recent researches have shown that there is a
need for a more valid and reliable tools, for assessing work stress. Thus artificial intelligence techniques have been applied in this
instance to provide a solution to a psychological application. An overview about the novel and autonomous interactive model for analysing work-stress that has been developedusing multi-agent
systems is also presented in this paper. The establishment of the intelligent multi-agent decision analyser (IMADA) using hybridized technique of neural networks and fuzzy logic within the multi-agent based framework is also described.
Abstract: In the current Grid environment, efficient workload
management presents a significant challenge, for which there are
exorbitant de facto standards encompassing resource discovery,
brokerage, and data transfer, among others. In addition, the real-time
resource status, essential for an optimal resource allocation strategy,
is often not readily accessible. To address these issues and provide a
cleaner abstraction of the Grid with the potential of generalizing into
arbitrary resource-sharing environment, this paper proposes a new
Condor-based pilot mechanism applied in the PanDA architecture,
PanDA-PF WMS, with the goal of providing a more generic yet
efficient resource allocating strategy. In this architecture, the PanDA
server primarily acts as a repository of user jobs, responding to pilot
requests from distributed, remote resources. Scheduling decisions are
subsequently made according to the real-time resource information
reported by pilots. Pilot Factory is a Condor-inspired solution for a
scalable pilot dissemination and effectively functions as a resource
provisioning mechanism through which the user-job server, PanDA,
reaches out to the candidate resources only on demand.
Abstract: Importance of environmental efficiency of electric power industry stems from high demand for energy combined with global warming concerns. It is especially essential for the world largest economies like that of the United States. The paper introduces a Data Envelopment Analysis (DEA) model of environmental efficiency using indicators of fossil fuels utilization, emissions rate, and electric power losses. Using DEA is advantageous in this situation over other approaches due to its nonparametric nature. The paper analyzes data for the period of 1990 - 2006 by comparing actual yearly levels in each dimension with the best values of partial indicators for the period. As positive factors of efficiency, tendency to the decline in emissions rates starting 2000, and in electric power losses starting 2004 may be mentioned together with increasing trend of fuel utilization starting 1999. As a result, dynamics of environmental efficiency is positive starting 2002. The main concern is the decline in fossil fuels utilization in 2006. This negative change should be reversed to comply with ecological and economic requirements.
Abstract: Scarcity of water resources and huge costs of
establishing new hydraulic installations necessitate optimal
exploitation from existing reservoirs. Sustainable management and
efficient exploitation from existing finite water resources are
important factors in water resource management, particularly in the
periods of water insufficiency and in dry regions, and on account of
competitive allocations in the view of exploitation management. This
study aims to minimize reservoir water release from a determined
rate of demand. A numerical model for water optimal exploitation
has been developed using GAMS introduced by the World Bank and
applied to the case of Meijaran dam, northern Iran. The results
indicate that this model can optimize the function of reservoir
exploitation while required water for lower parts of the region will be
supplied. Further, allocating optimal water from reservoir, the
optimal rate of water allocated to any group of the users were
specified to increase benefits in curve dam exploitation.
Abstract: When trying to enumerate all BIBD-s for given parameters,
their natural solution space appears to be huge and grows extremely with the number of points of the design. Therefore,
constructive enumerations are often carried out by assuming additional
constraints on design-s structure, automorphisms being mostly used ones. It remains a hard task to construct designs with trivial
automorphism group – those with no additional symmetry – although it is believed that most of the BIBD-s belong to that case. In
this paper, very many new designs with parameters 2-(13, 5, 5), 2-(16, 6, 5) and 2-(21, 6, 4) are constructed, assuming an action of an
automorphism of order 3. Even more, it was possible to construct millions of such designs with no non-trivial automorphisms.
Abstract: This paper presents an alternative strategy of queuing
handover called Pseudo Last Useful Instant PLUI scheme for Low
Earth Orbit Mobile Satellite Systems LEO MSSs. The PLUI scheme
uses the same approach as the Last Useful Instant LUI scheme
previously proposed in literature, with less complex implementation.
Simulation tests were carried out using Dynamic Channel Allocation
DCA in order to evaluate the performance of this scheme and also an
analytical approach has been presented to allow the performance
evaluation of Fixed Channel Allocation FCA, with different
handover queuing disciplines. The results show that performances
achieved by the proposed strategy are close to those achieved using
the LUI scheme.
Abstract: During last decades is widely discussed the
international harmonization of financial reporting. This
harmonization is also affected by national tax systems in analyzed
countries. This paper provides some evidence on current national tax
systems in selected countries in Central and Eastern Europe. The
linkage of accounting profit as a tax base might decrease the
administrative burden for majority of SMEs, which are the most
important engine of each national economy.
Abstract: e-mail has become an important means of electronic
communication but the viability of its usage is marred by Unsolicited
Bulk e-mail (UBE) messages. UBE consists of many types
like pornographic, virus infected and 'cry-for-help' messages as well
as fake and fraudulent offers for jobs, winnings and medicines. UBE
poses technical and socio-economic challenges to usage of e-mails.
To meet this challenge and combat this menace, we need to
understand UBE. Towards this end, the current paper presents a
content-based textual analysis of more than 2700 body enhancement
medicinal UBE. Technically, this is an application of Text Parsing
and Tokenization for an un-structured textual document and we
approach it using Bag Of Words (BOW) and Vector Space Document
Model techniques. We have attempted to identify the most
frequently occurring lexis in the UBE documents that advertise
various products for body enhancement. The analysis of such top
100 lexis is also presented. We exhibit the relationship between
occurrence of a word from the identified lexis-set in the given UBE
and the probability that the given UBE will be the one advertising for
fake medicinal product. To the best of our knowledge and survey of
related literature, this is the first formal attempt for identification of
most frequently occurring lexis in such UBE by its textual analysis.
Finally, this is a sincere attempt to bring about alertness against and
mitigate the threat of such luring but fake UBE.
Abstract: Eight heavy metals (Cu, Cr, Zn, Hg, Pb, Cd, Ni and As) were analyzed in sediment samples in the dry and wet seasons from November 2009 to October 2010 in West Port of Peninsular Malaysia. The heavy metal concentrations (mg/kg dry weight) were ranged from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. Metals concentrations in dry season were higher than the rainy season except in cupper and chromium. Analysis of variance with Statistical Analysis System (SAS) shows that the mean concentration of metals in the two seasons (α level=0.05) are not significantly different which shows that the metals were held firmly in the matrix of sediment. Also there are significant differences between control point station with other stations. According to the Interim Sediment Quality guidelines (ISQG), the metal concentrations are moderately polluted, except in arsenic which shows the highest level of pollution.
Abstract: Legionella pneumophila is involved in more than 95%
cases of severe atypical pneumonia. Infection is mainly by
inhalation the indoor aerosols through the water-coolant systems.
Because some Legionella strains may be viable but not culturable,
therefore, Taq polymerase, DNA amplification and semi-nested-PCR
were carried out to detect Legionella-specific 16S-rDNA sequence.
For this purpose, 1.5 litter of water samples from 77 water-coolant
system were collected from four different hospitals, two nursing
homes and one student hostel in Kerman city of Iran, each in a brand
new plastic bottle during summer season of 2006 (from April to
August). The samples were filtered in the sterile condition through
the Millipore Membrane Filter. DNA was extracted from membrane
and used for PCR to detect Legionella spp. The PCR product was
then subjected to semi-nested PCR for detection of L. pneumophila.
Out of 77 water samples that were tested by PCR, 30 (39%) were
positive for most species of Legionella. However, L. pneumophila
was detected from 14 (18.2%) water samples by semi-nested PCR.
From the above results it can be concluded that water coolant
systems of different hospitals and nursing homes in Kerman city of
Iran are highly contaminated with L. pneumophila spp. and pose
serious concern. So, we recommend avoiding such type of coolant
system in the hospitals and nursing homes.
Abstract: Exact expressions for bit-error probability (BEP) for
coherent square detection of uncoded and coded M-ary quadrature
amplitude modulation (MQAM) using an array of antennas with
maximal ratio combining (MRC) in a flat fading channel interference
limited system in a Nakagami-m fading environment is derived. The
analysis assumes an arbitrary number of independent and identically
distributed Nakagami interferers. The results for coded MQAM are
computed numerically for the case of (24,12) extended Golay code
and compared with uncoded MQAM by plotting error probabilities
versus average signal-to-interference ratio (SIR) for various values of
order of diversity N, number of distinct symbols M, in order to
examine the effect of cochannel interferers on the performance of the
digital communication system. The diversity gains and net gains are
also presented in tabular form in order to examine the performance of
digital communication system in the presence of interferers, as the
order of diversity increases. The analytical results presented in this
paper are expected to provide useful information needed for design
and analysis of digital communication systems with space diversity
in wireless fading channels.
Abstract: Cantilever L-shaped walls are known to be relatively economical as retaining solution. The design starts by proportioning the wall dimensions for which the stability is checked for. A ratio between the lengths of the base and the stem, falling between 0.5 to 0.7 ensure in most case the stability requirements, however, the displacement pattern of the wall in terms of rotations and translations, and the lateral pressure profile, do not have the same figure for all wall’s proportioning, as it is usually assumed. In the present work the results of a numerical analysis are presented, different wall geometries were considered. The results show that the proportioning governs the equilibrium between the instantaneous rotation and the translation of the wall-toe, also, the lateral pressure estimation based on the average value between the at-rest and the active pressure, recommended by most design standards, is found to be not applicable for all walls.
Abstract: Data Warehouses (DWs) are repositories which contain the unified history of an enterprise for decision support. The data must be Extracted from information sources, Transformed and integrated to be Loaded (ETL) into the DW, using ETL tools. These tools focus on data movement, where the models are only used as a means to this aim. Under a conceptual viewpoint, the authors want to innovate the ETL process in two ways: 1) to make clear compatibility between models in a declarative fashion, using correspondence assertions and 2) to identify the instances of different sources that represent the same entity in the real-world. This paper presents the overview of the proposed framework to model the ETL process, which is based on the use of a reference model and perspective schemata. This approach provides the designer with a better understanding of the semantic associated with the ETL process.
Abstract: Measurements of capacitance C and dissipation
factor tand of the stator insulation system provide useful information
about internal defects within the insulation. The index k is defined as
the proportionality constant between the changes at high voltage of
capacitance DC and of the dissipation factor Dtand . DC and
Dtand values were highly correlated when small flat defects were
within the insulation and that correlation was lost in the presence of
large narrow defects like electrical treeing. The discrimination
between small and large defects is made resorting to partial discharge
PD phase angle analysis. For the validation of the results, C and tand
measurements were carried out in a 15MVA 4160V steam turbine
turbogenerator placed in a sugar mill. In addition, laboratory test
results obtained by other authors were analyzed jointly. In such
laboratory tests, model coil bars subjected to thermal cycling resulted
highly degraded and DC and Dtand values were not correlated. Thus,
the index k could not be calculated.
Abstract: The article touches upon questions of information security in Russian Economy. It covers theoretical bases of information security and causes of its development. The theory is proved by the analysis of business activities and the main tendencies of information security development. Perm region has been chosen as the bases for the analysis, being the fastestdeveloping region that uses methods of information security in managing it economy. As a result of the study the authors of the given article have formulated their own vision of the problem of information security in various branches of economy and stated prospects of information security development and its growing role in Russian economy
Abstract: This paper aims to present knowledge management for solving economic problem and poverty in Thai community. A community in Thailand is studied as a case study for master plan or social and economic plan which derived form the research people conducted by themselves in their community. The result shows that community uses knowledge management in recording income and expense, analyzing their consumption, and then systematic planning of the production, distribution and consumption in the community. Besides, community enterprises, that people create as the by-products of master plan, can facilitate diverse economic activities which are able to reduce economic problem and poverty. The knowledge that people gain from solving their problem through building community enterprises are both tacit and explicit knowledge. Four styles of knowledge conversion: socialization,externalization, combination and internalization, are used. Besides, knowledge sharing inside the organization, between organizations and its environment are found. Keywordsknowledge management, community enterprise, Thailand.