Abstract: This paper was to study the clothes dryer using waste
heat from a split type air conditioner with a capacity of 12,648 btu/h.
The drying chamber had a minimum cross section area with the size
of 0.5 x 1.0 m2. The chamber was constructed by sailcloth and was
inside folded with aluminium foil. Then, it was connected to the
condensing unit of an air conditioner. The experiment was carried out
in two aspects which were the clothes drying with and without
auxiliary fan unit. The results showed that the drying rate of clothes
in the chamber installed with and without auxiliary fan unit were
2.26 and 1.1 kg/h, respectively. In case of the chamber installed with
a auxiliary fan unit, the additional power of 0.011 kWh was
consumed and the drying rate was higher than that of clothes drying
without auxiliary fan unit. Without auxiliary fan unit installation, no
energy was required but there was a portion of hot air leaks away
through the punctured holes at the wall of the drying chamber, hence
the drying rate was dropped below. The drying rate of clothes drying
using waste heat was higher than natural indoor drying and
commercial dryer which their drying rate were 0.17 and 1.9 kg/h,
respectively. It was noted that the COP of the air conditioner did not
change during the operating of clothes drying.
Abstract: Humic acids (HAs) have been shown to activate some
ion uptakes along with stimulating the lateral roots at effective
concentration of micronutrients. However, the effects of HA on ion
adsorption by plant roots are not easily explainable due to the
varieties of HAs that differ from origins. Therefore, this study was
aimed to investigate the effect of various concentrations of HA
obtained from the compost derived from mix manures and some
agricultural wastes on the growth of eggplant seedlings (Solanum
melongena L. cv. Chao Praya) in tissue cultures at low nutrient level.
Egg plant seeds were surfaced sterilized and germinated in ½
Murashige and Skoog medium (MS) without HA added or in ¼ MS
supplemented with 0, 25, 50, 75 and 100 ppm of HAs. Then, they
were cultured for 4 weeks under the controlled environment. The
results showed that seedlings grown on ¼MS supplemented with
HAs at the concentration of 25 and 50 ppm had the average plant
heights (2.49 and 2.28 cm, respectively) higher than the other
treatments. Both treatments also significantly showed the maximum
average fresh and dry weights (p
Abstract: The effect of the discontinuity of the rail ends and the
presence of lower modulus insulation material at the gap to the
variations of stresses in the insulated rail joint (IRJ) is presented. A
three-dimensional wheel – rail contact model in the finite element
framework is used for the analysis. It is shown that the maximum stress
occurs in the subsurface of the railhead when the wheel contact occurs
far away from the rail end and migrates to the railhead surface as the
wheel approaches the rail end; under this condition, the interface
between the rail ends and the insulation material has suffered
significantly increased levels of stress concentration. The ratio of the
elastic modulus of the railhead and insulation material is found to alter
the levels of stress concentration. Numerical result indicates that a
higher elastic modulus insulating material can reduce the stress
concentration in the railhead but will generate higher stresses in the
insulation material, leading to earlier failure of the insulation material
Abstract: Generally flow behavior in centrifugal fan is observed
to be in a state of instability with flow separation zones on suction
surface as well as near the front shroud. Overall performance of the
diffusion process in a centrifugal fan could be enhanced by
judiciously introducing the boundary layer suction slots. With easy
accessibility of CFD as an analytical tool, an extensive numerical
whole field analysis of the effect of boundary layer suction slots in
discrete regions of suspected separation points is possible. This paper
attempts to explore the effect of boundary layer suction slots
corresponding to various geometrical locations on the impeller with
converging configurations for the slots. The analysis shows that the
converging suction slots located on the impeller blade about 25%
from the trailing edge, significantly improves the static pressure
recovery across the fan. Also it is found that Slots provided at a
radial distance of about 12% from the leading and trailing edges
marginally improve the static pressure recovery across the fan.
Abstract: Markov games are a generalization of Markov
decision process to a multi-agent setting. Two-player zero-sum
Markov game framework offers an effective platform for designing
robust controllers. This paper presents two novel controller design
algorithms that use ideas from game-theory literature to produce
reliable controllers that are able to maintain performance in presence
of noise and parameter variations. A more widely used approach for
controller design is the H∞ optimal control, which suffers from high
computational demand and at times, may be infeasible. Our approach
generates an optimal control policy for the agent (controller) via a
simple Linear Program enabling the controller to learn about the
unknown environment. The controller is facing an unknown
environment, and in our formulation this environment corresponds to
the behavior rules of the noise modeled as the opponent. Proposed
controller architectures attempt to improve controller reliability by a
gradual mixing of algorithmic approaches drawn from the game
theory literature and the Minimax-Q Markov game solution
approach, in a reinforcement-learning framework. We test the
proposed algorithms on a simulated Inverted Pendulum Swing-up
task and compare its performance against standard Q learning.
Abstract: Wireless Sensor Networks (WSNs) have attracted the attention of many researchers. This has resulted in their rapid integration in very different areas such as precision agriculture,environmental monitoring, object and event detection and military surveillance. Due to the current WSN characteristics this technology is specifically useful in industrial areas where security, reliability and autonomy are basic, such as nuclear power plants, chemical plants, and others. In this paper we present a system based on WSNs to monitor environmental conditions around and inside a nuclear power plant, specifically, radiation levels. Sensor nodes, equipped with radiation sensors, are deployed in fixed positions throughout the plant. In addition, plant staff are also equipped with mobile devices with higher capabilities than sensors such as for example PDAs able to monitor radiation levels and other conditions around them. The system enables communication between PDAs, which form a Mobile Ad-hoc Wireless Network (MANET), and allows workers to monitor remote conditions in the plant. It is particularly useful during stoppage periods for inspection or in the event of an accident to prevent risk situations.
Abstract: The purpose of this study is to investigate the chemical
degradation of the organophosphorus pesticide of parathion and
carbamate insecticide of methomyl in the aqueous phase through
Fenton process. With the employment of batch Fenton process, the
degradation of the two selected pesticides at different pH, initial
concentration, humic acid concentration, and Fenton reagent dosages
was explored. The Fenton process was found effective to degrade
parathion and methomyl. The optimal dosage of Fenton reagents (i.e.,
molar concentration ratio of H2O2 to Fe2+) at pH 7 for parathion
degradation was equal to 3, which resulted in 50% removal of
parathion. Similarly, the optimal dosage for methomyl degradation
was 1, resulting in 80% removal of methomyl. This study also found
that the presence of humic substances has enhanced pesticide
degradation by Fenton process significantly. The mass spectroscopy
results showed that the hydroxyl free radical may attack the single
bonds with least energy of investigated pesticides to form smaller
molecules which is more easily to degrade either through
physio-chemical or bilolgical processes.
Abstract: This paper investigates the relationship between state and business in the context of structural and institutional transformations in Indonesia following the collapse of the New Order regime in 1998. Since 1998, Indonesia has embarked on a shift from an authoritarian to democratic polity and from a centralised to a decentralised system of governance, transforming the country into the third largest democracy and one of the most decentralised states in the world. This paper examines whether the transformation of the Indonesian state has altered the pattern of state and business relations with focus on clientism and corruption as the key dependent variable, and probes how/to what extent this has changed as a result of the transformation and the ensuring shifts in business and state relations. Based on interviews with key government and business actors as well as prominent scholars in Indonesia, it is found that since the demise of the New Order, business associations in Indonesia have become more independent of state control and more influential in public decision-making whereas the government has become more responsive of business concerns and more committed to combat corruption and clientism. However, these changes have not necessarily rendered business people completely leave individualclientelistic relationship with the government, and simply pursue wider sectoral and business-wide collectivism as an alternative way of channelling their aspirations, which is expected to help reduce corruption and clientism in Indonesia. This paper concludes that democratisation and a more open politics may have helped reduce corruption and clientism in Indonesia through changes in government. However, it is still difficult to imply that such political transformation has fostered business collective action and a broader, more encompassing pattern of business lobbying and activism, which is expected to help reduce corruption and clientism.
Abstract: Dill contains range of phytochemicals, such as vitamin C and polyphenols, which significantly contribute to their total antioxidant activity. The aim of the current research was to determine the best blanching method for processing of dill prior to microwave vacuum drying based on the content of phenolic compounds, vitamin C and free radical scavenging activity. Two blanching mediums were used – water and steam, and for part of the samples microwave pretreatment was additionally used. Evaluation of vitamin C, phenolic contents and scavenging of DPPH˙ radical in dried dill was performed. Blanching had an effect on all tested parameters and the blanching conditions are very important. After evaluation of the results, as the best method for dill pretreatment was established blanching at 90 °C for 30 seconds.
Abstract: The overlay approach has been widely used by many service providers for Traffic Engineering (TE) in large Internet backbones. In the overlay approach, logical connections are set up between edge nodes to form a full mesh virtual network on top of the physical topology. IP routing is then run over the virtual network. Traffic engineering objectives are achieved through carefully routing logical connections over the physical links. Although the overlay approach has been implemented in many operational networks, it has a number of well-known scaling issues. This paper proposes a new approach to achieve traffic engineering without full-mesh overlaying with the help of integrated approach and equal subset split method. Traffic engineering needs to determine the optimal routing of traffic over the existing network infrastructure by efficiently allocating resource in order to optimize traffic performance on an IP network. Even though constraint-based routing [1] of Multi-Protocol Label Switching (MPLS) is developed to address this need, since it is not widely tested or debugged, Internet Service Providers (ISPs) resort to TE methods under Open Shortest Path First (OSPF), which is the most commonly used intra-domain routing protocol. Determining OSPF link weights for optimal network performance is an NP-hard problem. As it is not possible to solve this problem, we present a subset split method to improve the efficiency and performance by minimizing the maximum link utilization in the network via a small number of link weight modifications. The results of this method are compared against results of MPLS architecture [9] and other heuristic methods.
Abstract: The major challenge faced by wireless sensor networks is security. Because of dynamic and collaborative nature of sensor networks the connected sensor devices makes the network unusable. To solve this issue, a trust model is required to find malicious, selfish and compromised insiders by evaluating trust worthiness sensors from the network. It supports the decision making processes in wireless sensor networks such as pre key-distribution, cluster head selection, data aggregation, routing and self reconfiguration of sensor nodes. This paper discussed the kinds of trust model, trust metrics used to address attacks by monitoring certain behavior of network. It describes the major design issues and their countermeasures of building trust model. It also discusses existing trust models used in various decision making process of wireless sensor networks.
Abstract: Rainbow trout homogametic males, (XX or YY sex genotype), can be obtained, respectively, through masculinisation of genetic females or induced androgenesis. Aim of this study was to compare reproductive potential of neo-males (XX) and super-males (YY) with heterogametic males (XY). We measured spermatozoa motility parameters, sperm concentration, osmolality and characterized protein profiles in samples of stripped and testicular sperm obtained from XY and YY males, and testicular sperm of XX males. The motile spermatozoa, as measured by both subjective method and CASA, showed no differences between testicular sperm of XX males and stripped sperm of XY and YY males whereas testicular sperm of XY and YY males had significantly lower sperm motility. Result of protein densitometry showed similarities in protein profile between seminal plasma of XY and YY males and testicular fluids of XX males. Testis of XX males showed specific histological structures of cysts consists hypertrophied Sertoli cells.
Abstract: The move towards internationalization of accounting encountered a great boost, when in 2002 EU delegated the IASB to provide the accounting standards to be applied inside its frontiers. Among the incentives of the standardization of accounting on the international level, is the reduction of the cost of capital. Romania made the move towards IFRS before EU, when the country was not yet a member of it. Even if this made Romania a special case, it was scarcely approached. The leak of real data is usually the reason for avoiding. The novelty of this paper is that it offers an insight from the reality of Romanian companies and their view regarding the IFRS. The paper is based on a survey that the authors made among the companies listed on the first two tiers of the Bucharest Stock Exchange (BSE), which are basically, the most important companies in the country.
Abstract: Background: Regular physical activity contributes
positively to physical and psychological health. In the present study,
the stages of change of physical activity and the total physical
Aims: The aim of this study was to investigate the proportion of
adolescent girls in each stages of change and the causative factors
associated with physical activity such as the related social support
and self efficacy in a sample of the high school students.
Methods: In this study, Social Cognitive Theory (SCT) and the
Transtheorical Model (TTM) guided instrument development. The
data regarding the demographics, psychosocial determinants of
physical activity, stage of change and physical activity was gathered
by questionnaires. Several measures of psychosocial determinants of
physical activity were translated from English into Persian using the
back-translation technique. These translated measures were
administered to 512 ninth and tenth-grade Iranian high school
students for factor analysis.
Results: The distribution of the stage of change for physical activity
was as follow: 18/5% in precontemplation, 23.4% in contemplation,
38.2% in preparation, 4.6% in action and 15.3% in maintenance.
They were in 80.1% pre-adoption stages (precontemplation stage,
contemplation stage and preparation stage) and 19.9% post-adoption
stages (action stage and maintenance stage) of physical activity.
There was a significant relate between age and physical activity in
adolescent girls (age-related decline of physical activity) p
Abstract: this article proposed a methodology for computer
numerical control (CNC) machine scoring. The case study company
is a manufacturer of hard disk drive parts in Thailand. In this
company, sample of parts manufactured from CNC machine are
usually taken randomly for quality inspection. These inspection data
were used to make a decision to shut down the machine if it has
tendency to produce parts that are out of specification. Large amount
of data are produced in this process and data mining could be very
useful technique in analyzing them. In this research, data mining
techniques were used to construct a machine scoring model called
'machine priority assessment model (MPAM)'. This model helps to
ensure that the machine with higher risk of producing defective parts
be inspected before those with lower risk. If the defective prone
machine is identified sooner, defective part and rework could be
reduced hence improving the overall productivity. The results
showed that the proposed method can be successfully implemented
and approximately 351,000 baht of opportunity cost could have
saved in the case study company.
Abstract: Tanzania secondary schools in rural areas are geographically and socially isolated, hence face a number of problems in getting learning materials resulting in poor performance in National examinations. E-learning as defined to be the use of information and communication technology (ICT) for supporting the educational processes has motivated Tanzania to apply ICT in its education system. There has been effort to improve secondary school education using ICT through several projects. ICT for e-learning to Tanzania rural secondary school is one of the research projects conceived by the University of Dar-es-Salaam through its College of Engineering and Technology. The main objective of the project is to develop a tool to enable ICT support rural secondary school. The project is comprehensive with a number of components, one being development of e-learning management system (e-LMS) for Tanzania secondary schools. This paper presents strategies of developing e-LMS. It shows the importance of integrating action research methodology with the modeling methods as presented by model driven architecture (MDA) and the usefulness of Unified Modeling Language (UML) on the issue of modeling. The benefit of MDA will go along with the development based on software development life cycle (SDLC) process, from analysis and requirement phase through design and implementation stages as employed by object oriented system analysis and design approach. The paper also explains the employment of open source code reuse from open source learning platforms for the context sensitive development of the e-LMS for Tanzania secondary schools.
Abstract: The sequence Analyze, Design, Develop, Implement, and Evaluate (ADDIE) provides a powerful methodology for designing computer-based educational materials. Helping students to understand this design process sequence may be achieved by providing them with direct, guided experience. This article examines such help and guidance and the overall learning process from a student-s personal experience.
Abstract: Quantitative Structure-Activity Relationship (QSAR)
approach for discovering novel more active Calanone derivative as
anti-leukemia compound has been conducted. There are 6
experimental activities of Calanone compounds against leukemia cell
L1210 that are used as material of the research. Calculation of
theoretical predictors (independent variables) was performed by
AM1 semiempirical method. The QSAR equation is determined by
Principle Component Regression (PCR) analysis, with Log IC50 as
dependent variable and the independent variables are atomic net
charges, dipole moment (μ), and coefficient partition of noctanol/
water (Log P). Three novel Calanone derivatives that
obtained by this research have higher activity against leukemia cell
L1210 than pure Calanone.
Abstract: We present a discussion of three adaptive filtering
algorithms well known for their one-step termination property, in
terms of their relationship with the minimal residual method. These
algorithms are the normalized least mean square (NLMS), Affine
Projection algorithm (APA) and the recursive least squares algorithm
(RLS). The NLMS is shown to be a result of the orthogonality
condition imposed on the instantaneous approximation of the Wiener
equation, while APA and RLS algorithm result from orthogonality
condition in multi-dimensional minimal residual formulation. Further
analysis of the minimal residual formulation for the RLS leads to
a triangular system which also possesses the one-step termination
property (in exact arithmetic)