Abstract: Energy and exergy study of air-water combined solar collector which is called dual purpose solar collector (DPSC) is investigated. The method of ε - NTU is used. Analysis is performed for triangle channels. Parameters like the air flow rate and water inlet temperature are studied. Results are shown that DPSC has better energy and exergy efficiency than single collector. In addition, the triangle passage with water inlet temperature of 60O C has shown better exergy and energy efficiency.
Abstract: A new method identifies coupled fluid-structure system with a reduced set of state variables is presented. Assuming that the structural model is known a priori either from an analysis or a test and using linear transformations between structural and aeroelastic states, it is possible to deduce aerodynamic information from sampled time histories of the aeroelastic system. More specifically given a finite set of structural modes the method extracts generalized aerodynamic force matrix corresponding to these mode shapes. Once the aerodynamic forces are known, an aeroelastic reduced-order model can be constructed in discrete-time, state-space format by coupling the structural model and the aerodynamic system. The resulting reduced-order model is suitable for constant Mach, varying density analysis.
Abstract: This study examines the inelastic behavior of adjacent planar reinforced concrete (R.C.) frames subjected to strong ground motions. The investigation focuses on the effects of vertical ground motion on the seismic pounding. The examined structures are modeled and analyzed by RUAUMOKO dynamic nonlinear analysis program using reliable hysteretic models for both structural members and contact elements. It is found that the vertical ground motion mildly affects the seismic response of adjacent buildings subjected to structural pounding and, for this reason, it can be ignored from the displacement and interstorey drifts assessment. However, the structural damage is moderately affected by the vertical component of earthquakes.
Abstract: The purpose of this study was to investigate relationships between satisfaction with major and career decision efficacy and career attitude maturity of engineering college students by performing correlation analysis. Gender differences in between satisfaction with major and career decision efficacy and career attitude maturity were also examined by T-test. The results T-test revealed gender differences in only career decision efficacy. Male Students scored significantly higher than did female students on career decision efficacy and satisfaction with major. The results of correlation analysis showed a) satisfaction with major were significantly associated with career decision efficacy, b) satisfaction with major were significantly associated with career attitude maturity, and c) career decision efficacy were significantly associated with career attitude maturity. As a result,we found the importance of satisfaction in engineering college students- major studies when deciding their career.
Abstract: During last decades is widely discussed the
international harmonization of financial reporting. This
harmonization is also affected by national tax systems in analyzed
countries. This paper provides some evidence on current national tax
systems in selected countries in Central and Eastern Europe. The
linkage of accounting profit as a tax base might decrease the
administrative burden for majority of SMEs, which are the most
important engine of each national economy.
Abstract: The aim of this paper is to examine factors related to system environment (namely, system quality and vendor support) that influences ERP implementation success in Iranian companies. Implementation success is identified using user satisfaction and organizational impact perspective. The study adopts the survey questionnaire approach to collect empirical data. The questionnaire was distributed to ERP users and a total of 384 responses were used for analysis. The results illustrated that both system quality and vendor support have significant effect on ERP implementation success. This implies that companies must ensure they source for the best available system and a vendor that is dependable, reliable and trustworthy.
Abstract: This article presents a current-mode universal biquadratic filter. The proposed circuit can apparently provide standard functions of the biquad filter: low-pass, high-pass, bandpass, band-reject and all-pass functions. The circuit uses 4 current controlled transconductance amplifiers (CCTAs) and 2 grounded capacitors. In addition, the pole frequency and quality factor can be adjusted by electronic method by adjusting the bias currents of the CCTA. The proposed circuit uses only grounded capacitors without additional external resistors, the proposed circuit is considerably appropriate to further developing into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.
Abstract: e-mail has become an important means of electronic
communication but the viability of its usage is marred by Unsolicited
Bulk e-mail (UBE) messages. UBE consists of many types
like pornographic, virus infected and 'cry-for-help' messages as well
as fake and fraudulent offers for jobs, winnings and medicines. UBE
poses technical and socio-economic challenges to usage of e-mails.
To meet this challenge and combat this menace, we need to
understand UBE. Towards this end, the current paper presents a
content-based textual analysis of more than 2700 body enhancement
medicinal UBE. Technically, this is an application of Text Parsing
and Tokenization for an un-structured textual document and we
approach it using Bag Of Words (BOW) and Vector Space Document
Model techniques. We have attempted to identify the most
frequently occurring lexis in the UBE documents that advertise
various products for body enhancement. The analysis of such top
100 lexis is also presented. We exhibit the relationship between
occurrence of a word from the identified lexis-set in the given UBE
and the probability that the given UBE will be the one advertising for
fake medicinal product. To the best of our knowledge and survey of
related literature, this is the first formal attempt for identification of
most frequently occurring lexis in such UBE by its textual analysis.
Finally, this is a sincere attempt to bring about alertness against and
mitigate the threat of such luring but fake UBE.
Abstract: This paper includes two novel techniques for skew
estimation of binary document images. These algorithms are based on
connected component analysis and Hough transform. Both these
methods focus on reducing the amount of input data provided to
Hough transform. In the first method, referred as word centroid
approach, the centroids of selected words are used for skew detection.
In the second method, referred as dilate & thin approach, the selected
characters are blocked and dilated to get word blocks and later
thinning is applied. The final image fed to Hough transform has the
thinned coordinates of word blocks in the image. The methods have
been successful in reducing the computational complexity of Hough
transform based skew estimation algorithms. Promising experimental
results are also provided to prove the effectiveness of the proposed
methods.
Abstract: Eight heavy metals (Cu, Cr, Zn, Hg, Pb, Cd, Ni and As) were analyzed in sediment samples in the dry and wet seasons from November 2009 to October 2010 in West Port of Peninsular Malaysia. The heavy metal concentrations (mg/kg dry weight) were ranged from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. Metals concentrations in dry season were higher than the rainy season except in cupper and chromium. Analysis of variance with Statistical Analysis System (SAS) shows that the mean concentration of metals in the two seasons (α level=0.05) are not significantly different which shows that the metals were held firmly in the matrix of sediment. Also there are significant differences between control point station with other stations. According to the Interim Sediment Quality guidelines (ISQG), the metal concentrations are moderately polluted, except in arsenic which shows the highest level of pollution.
Abstract: Exact expressions for bit-error probability (BEP) for
coherent square detection of uncoded and coded M-ary quadrature
amplitude modulation (MQAM) using an array of antennas with
maximal ratio combining (MRC) in a flat fading channel interference
limited system in a Nakagami-m fading environment is derived. The
analysis assumes an arbitrary number of independent and identically
distributed Nakagami interferers. The results for coded MQAM are
computed numerically for the case of (24,12) extended Golay code
and compared with uncoded MQAM by plotting error probabilities
versus average signal-to-interference ratio (SIR) for various values of
order of diversity N, number of distinct symbols M, in order to
examine the effect of cochannel interferers on the performance of the
digital communication system. The diversity gains and net gains are
also presented in tabular form in order to examine the performance of
digital communication system in the presence of interferers, as the
order of diversity increases. The analytical results presented in this
paper are expected to provide useful information needed for design
and analysis of digital communication systems with space diversity
in wireless fading channels.
Abstract: Cantilever L-shaped walls are known to be relatively economical as retaining solution. The design starts by proportioning the wall dimensions for which the stability is checked for. A ratio between the lengths of the base and the stem, falling between 0.5 to 0.7 ensure in most case the stability requirements, however, the displacement pattern of the wall in terms of rotations and translations, and the lateral pressure profile, do not have the same figure for all wall’s proportioning, as it is usually assumed. In the present work the results of a numerical analysis are presented, different wall geometries were considered. The results show that the proportioning governs the equilibrium between the instantaneous rotation and the translation of the wall-toe, also, the lateral pressure estimation based on the average value between the at-rest and the active pressure, recommended by most design standards, is found to be not applicable for all walls.
Abstract: Measurements of capacitance C and dissipation
factor tand of the stator insulation system provide useful information
about internal defects within the insulation. The index k is defined as
the proportionality constant between the changes at high voltage of
capacitance DC and of the dissipation factor Dtand . DC and
Dtand values were highly correlated when small flat defects were
within the insulation and that correlation was lost in the presence of
large narrow defects like electrical treeing. The discrimination
between small and large defects is made resorting to partial discharge
PD phase angle analysis. For the validation of the results, C and tand
measurements were carried out in a 15MVA 4160V steam turbine
turbogenerator placed in a sugar mill. In addition, laboratory test
results obtained by other authors were analyzed jointly. In such
laboratory tests, model coil bars subjected to thermal cycling resulted
highly degraded and DC and Dtand values were not correlated. Thus,
the index k could not be calculated.
Abstract: The article touches upon questions of information security in Russian Economy. It covers theoretical bases of information security and causes of its development. The theory is proved by the analysis of business activities and the main tendencies of information security development. Perm region has been chosen as the bases for the analysis, being the fastestdeveloping region that uses methods of information security in managing it economy. As a result of the study the authors of the given article have formulated their own vision of the problem of information security in various branches of economy and stated prospects of information security development and its growing role in Russian economy
Abstract: In built-up structures, one of the effective ways of
dissipating unwanted vibration is to exploit the occurrence of slip at
the interfaces of structural laminates. The present work focuses on
the dynamic analysis of welded structures. A mathematical
formulation has been developed for the mechanism of slip damping
in layered and welded mild steel beams with unequal thickness
subjected to both periodic and non-periodic forces. It is observed that
a number of vital parameters such as; thickness ratio, pressure
distribution characteristics, relative slip and kinematic co-efficient of
friction at the interfaces, nature of exciting forces, length and
thickness of the beam specimen govern the damping characteristics of
these structures. Experimental verification has been carried out to
validate the analysis and study the effect of these parameters. The
developed damping model for the structure is found to be in fairly
good agreement with the measured data. Finally, the results of the
analysis are discussed and rationalized.
Abstract: In this paper, we propose a hybrid machine learning
system based on Genetic Algorithm (GA) and Support Vector
Machines (SVM) for stock market prediction. A variety of indicators
from the technical analysis field of study are used as input features.
We also make use of the correlation between stock prices of different
companies to forecast the price of a stock, making use of technical
indicators of highly correlated stocks, not only the stock to be
predicted. The genetic algorithm is used to select the set of most
informative input features from among all the technical indicators.
The results show that the hybrid GA-SVM system outperforms the
stand alone SVM system.
Abstract: This study focuses on an evaluation of Hokkaido which
is the northernmost and largest prefecture by surface area in Japan and
particularly on two points: the rivalry between all kinds of land use
such as urban land and agricultural and forestry land in various cities
and their surrounding areas and the possibilities for forestry biomass in
areas other than those mentioned above and grasps which areas require
examination of the nature of land use control and guidance through
conducting land use analysis at the district level using GIS
(Geographic Information Systems). The results of analysis in this
study demonstrated that it is essential to divide the whole of Hokkaido
into two areas: those within delineated city planning areas and those
outside of delineated city planning areas and to conduct an evaluation
of each land use control.
In delineated urban areas, particularly urban areas, it is essential to
re-examine land use from the point of view of compact cities or smart
cities along with conducting an evaluation of land use control that
focuses on issues of rivalry between all kinds of land use such as urban
land and agricultural and forestry land. In areas outside of delineated
urban areas, it is desirable to aim to build a specific community
recycling range based on forest biomass utilization by conducting an
evaluation of land use control concerning the possibilities for forest
biomass focusing particularly on forests within and outside of city
planning areas.
Abstract: In this paper, a model for an information retrieval
system is proposed which takes into account that knowledge about
documents and information need of users are dynamic. Two
methods are combined, one qualitative or symbolic and the other
quantitative or numeric, which are deemed suitable for many
clustering contexts, data analysis, concept exploring and
knowledge discovery. These two methods may be classified as
inductive learning techniques. In this model, they are introduced to
build “long term" knowledge about past queries and concepts in a
collection of documents. The “long term" knowledge can guide
and assist the user to formulate an initial query and can be
exploited in the process of retrieving relevant information. The
different kinds of knowledge are organized in different points of
view. This may be considered an enrichment of the exploration
level which is coherent with the concept of document/query
structure.
Abstract: A game animals – elk (Alces alces), deer (Cervus
elaphus), roe deer (Capreolus capreolus) or wild boar (Sus scrofa
scrofa) - every autumn and winter period provide an excellent
investment, diversification of many consumer meals. In last years
consumption and assortiment of game meat products significantly
increase. Investigations about biochemical composition of game meat
are not very much. The meat of wild animals is more favourable for
human health because it has lower saturated fatty acids content, but
higher content of protein. Therefore the aim of investigations was to
compare biochemical composition of ungulates obtained in
Latvia.Investigations were carried out in wild animals different
regions of Latvia. In the studied samples protein, intramuscular fat,
fatty acids and cholesterol were determined. The biochemical
analysis of 54 samples were done. Results of analysis showed that
protein content 22.36 – 22.92% of all types of meat samples is not
different statistically, significantly lower fat content 1.33 ± 0.88%
had elk meat samples and 1.59 ± 0.59% roe deer samples. Content of
cholesterol was various 64.41 – 95.07% in the ruminant meat
samples of different species. From the dietetic point of view the best
composition of fatty acids has meat samples of roe deer.
Abstract: Microbial oil was produced by soil isolated
oleaginous yeast YU5/2 in flask-batch fermentation. The yeast was
identified by molecular genetics technique based on sequence
analysis of the variable D1/D2 domain of the large subunit (26S)
ribosomal DNA and it was identified as Torulaspora globosa. T.
globosa YU5/2 supported maximum values of 0.520 g/L/d, 0.472 g
lipid/g cells, 4.16 g/L, and 0.156 g/L/d for volumetric lipid
production rate, and specific yield of lipid, lipid concentration, and
specific rate of lipid production respectively, when culture was
performed in nitrogen-limiting medium supplemented with 80g/L
glucose. Among the carbon sources tested, maximum cell yield
coefficient (YX/S, g/L), maximum specific yield of lipid (YP/X, g
lipid/g cells) and volumetric lipid production rate (QP, g/L/d) were
found of 0.728, 0.237, and 0.619, respectively, using sweet potato
tubers hydrolysates as carbon source.