Abstract: A long-term campaign for monitoring the
concentration of atmospheric Particulate Matter (PM) was conducted
at multiple sites located in the center and suburbs of the Tokyo
Metropolitan Area in Japan. The concentration of fine PM has shown a
declining trend over the last two decades. A positive matrix
factorization model elucidated that the contribution of combustion
sources was drastically reduced. In Japan, the regulations on vehicle
exhaust emissions were phased in and gradually tightened over the last
two decades, which has triggered a notable reduction in PM emissions
from automobiles and has contributed to the mitigation of the problem
of fine PM pollution.
Abstract: The desulfurization of coal using biological methods is an emerging technology. The biodesulfurization process uses the catalytic activity of chemolithotrophic acidpohiles in removing sulfur and pyrite from the coal. The present study was undertaken to examine the potential of Acidithiobacillus ferrooxidans in removing the pyritic sulfur and iron from high iron and sulfur containing US coal. The experiment was undertaken in 10 L batch stirred tank reactor having 10% pulp density of coal. The reactor was operated under mesophilic conditions and aerobic conditions were maintained by sparging the air into the reactor. After 35 days of experiment, about 64% of pyrite and 21% of pyritic sulfur was removed from the coal. The findings of the present study indicate that the biodesulfurization process does have potential in treating the high pyrite and sulfur containing coal. A good mass balance was also obtained with net loss of about 5% showing its feasibility for large scale application.
Abstract: Coordinated supply chain represents major challenges
for the different actors involved in it, because each agent responds to
individual interests. The paper presents a framework with the
reviewed literature regarding the system's decision structure and
nature of demand. Later, it characterizes an agri food supply chain in
the Central Region of Colombia, it responds to a decentralized
distribution system and a stochastic demand. Finally, the paper
recommends coordinating the chain based on shared information, and
mechanisms for each agent, as VMI (vendor-managed inventory)
strategy for farmer-buyer relationship, information system for
farmers and contracts for transportation service providers.
Abstract: The article deals with numerical investigation of axisymmetric
subsonic air to air ejector. An analysis of flow and mixing
processes in cylindrical mixing chamber are made. Several modes
with different velocity and ejection ratio are presented. The mixing
processes are described and differences between flow in the initial
region of mixing and the main region of mixing are described. The
lengths of both regions are evaluated. Transition point and point
where the mixing processes are finished are identified. It was found
that the length of the initial region of mixing is strongly dependent on
the velocity ratio, while the length of the main region of mixing is
dependent on velocity ratio only slightly.
Abstract: In a complex project environment, project teams face
multi-dimensional communication problems that can ultimately lead
to project breakdown. Team Performance varies in Face-to-Face
(FTF) environment versus groups working remotely in a computermediated
communication (CMC) environment. A brief review of the
Input_Process_Output model suggested by James E. Driskell, Paul H.
Radtke and Eduardo Salas in “Virtual Teams: Effects of
Technological Mediation on Team Performance (2003)", has been
done to develop the basis of this research. This model theoretically
analyzes the effects of technological mediation on team processes,
such as, cohesiveness, status and authority relations, counternormative
behavior and communication. An empirical study
described in this paper has been undertaken to test the
“cohesiveness" of diverse project teams in a multi-national
organization. This study uses both quantitative and qualitative
techniques for data gathering and analysis. These techniques include
interviews, questionnaires for data collection and graphical data
representation for analyzing the collected data. Computer-mediated
technology may impact team performance because of difference in
cohesiveness among teams and this difference may be moderated by
factors, such as, the type of communication environment, the type of
task and the temporal context of the team. Based on the reviewed
model, sets of hypotheses are devised and tested. This research,
reports on a study that compared team cohesiveness among virtual
teams using CMC and non-CMC communication mediums. The
findings suggest that CMC can help virtual teams increase team
cohesiveness among their members, making CMC an effective
medium for increasing productivity and team performance.
Abstract: New design of a grid for preparation of high density
granules with enhanced mechanical strength by granulation of
dispersed materials is suggested.
A method for hydrodynamic dimensioning of the grid depending
on granulation conditions, hydrodynamic regime of the operation,
dispersity and physicochemical characteristics of the materials to be
granulated was suggested.
The aim of the grid design is to solve the problems arising by the
granulation of disperse materials.
Abstract: The stone is a constituent part of the geological
structure of the Territory, introducing himself as a subject that has always interconnected human and environment in the development of a discourse of meanings and symbols that reflect elements realized in
different cultures and experiences.
This action meant that the first settlements and their areas of influence gained importance in the field of humanization and spatial
organization of the territory, not only for the appropriation that its
inhabitants did, but mainly because the community regardless of their
economic or social condition, used it as living space and cultural integration.
These factors become decisive in the characterization of the
landscape area in the northwest of Portugal, because the stone is a
material that appears not only in the natural landscape, but is also a strong element in humanized landscape, becoming this relation the
main characterization of the study area.
Abstract: The problem of ranking (rank regression) has become popular in the machine learning community. This theory relates to problems, in which one has to predict (guess) the order between objects on the basis of vectors describing their observed features. In many ranking algorithms a convex loss function is used instead of the 0-1 loss. It makes these procedures computationally efficient. Hence, convex risk minimizers and their statistical properties are investigated in this paper. Fast rates of convergence are obtained under conditions, that look similarly to the ones from the classification theory. Methods used in this paper come from the theory of U-processes as well as empirical processes.
Abstract: This paper studies mixed-mode fracture mechanics in
rock based on experimental and numerical analyses. Experiments
were performed on sharp-cracked specimens using the modified
Arcan specimen test loading device. The modified Arcan specimen
test was, in association with a special loading device, an appropriate
apparatus for experimental mixed-mode fracture analysis. By
varying the loading angle from 0° to 90°, pure mode-I, pure mode-II
and a wide range of mixed-mode data were obtained experimentally.
Using the finite element results, correction factors applied to the
rectangular fracture specimen. By employing experimentally
measured critical loads and the aid of the finite element method,
mixed-mode fracture toughness for the limestone under consideration
determined.
Abstract: The Long-range Energy and Alternatives Planning (LEAP) energy planning system has been developed for South Africa, for the 2005 base year and a limited number of plausible future scenarios that may have significant implications (negative or positive) in terms of environmental impacts. The system quantifies the national energy demand for the domestic, commercial, transport, industry and agriculture sectors, the supply of electricity and liquid fuels, and the resulting emissions. The South African National Energy Research Institute (SANERI) identified the need to develop an environmental assessment tool, based on the LEAP energy planning system, to provide decision-makers and stakeholders with the necessary understanding of the environmental impacts associated with different energy scenarios. A comprehensive analysis of indicators that are used internationally and in South Africa was done and the available data was accessed to select a reasonable number of indicators that could be utilized in energy planning. A consultative process was followed to determine the needs of different stakeholders on the required indicators and also the most suitable form of reporting. This paper demonstrates the application of Energy Environmental Sustainability Indicators (EESIs) as part of the developed tool, which assists with the identification of the environmental consequences of energy generation and use scenarios and thereby promotes sustainability, since environmental considerations can then be integrated into the preparation and adoption of policies, plans, programs and projects. Recommendations are made to refine the tool further for South Africa.
Abstract: Breastfeeding has been receiving much attention of late. Prolonged sitting for breastfeeding often results in back pain of the mothers. This paper reports the findings of a study on the effect of some factors, especially lumbar support, on back pain of breastfeeding mothers. The results showed that the use of lumbar support can reduce back pain of breastfeeding mothers significantly. Back pain was found to increase with breastfeeding time and the rate of increase was lower when lumbar supports were used. When lumbar support thickness was increased gradually from zero (no support) to 11 cm., the degree of low back pain decreased; rapidly at first, then slowly, and leveled off when the thickness reached 9 cm. Younger mothers were less prone to back pain than older mothers. The implications of the findings are discussed.
Abstract: This paper presents a integer frequency offset (IFO)
estimation scheme for the 3GPP long term evolution (LTE) downlink
system. Firstly, the conventional joint detection method for IFO and
sector cell index (CID) information is introduced. Secondly, an IFO
estimation without explicit sector CID information is proposed, which
can operate jointly with the proposed IFO estimation and reduce
the time delay in comparison with the conventional joint method.
Also, the proposed method is computationally efficient and has almost
similar performance in comparison with the conventional method over
the Pedestrian and Vehicular channel models.
Abstract: Petrol Fuel Station (PFS) has potential hazards to the
people, asset, environment and reputation of an operating company.
Fire hazards, static electricity air pollution evoked by aliphatic and
aromatic organic compounds are major causes of accident/incident
occurrence at fuel station. Activities such as carelessness,
maintenance, housekeeping, slips trips and falls, transportation
hazard, major and minor injuries, robbery and snake bites has a
potential to create unsafe conditions. The level of risk of these
hazards varies according to location and country. The emphasis on
safety considerations by the government is variable all around the
world. Developed countries safety records are much better as
compared to developing countries safety statistics. There is no
significant approach available to highlight the unsafe acts and unsafe
conditions during operation and maintenance of fuel station. Fuel
station is the most commonly available facilities that contain
flammable and hazardous materials. Due to continuous operation of
fuel station they pose various hazards to people, environment and
assets of an organization. To control these hazards, there is a need for
specific approach. PFS operation is unique as compared to other
businesses. For smooth operations it demands an involvement of
operating company, contractor and operator group. This study will
focus to address hazard contributing factors that have a potential to
make PFS operation risky. One year data collected, 902 activities
analyzed, comparisons were made to highlight significant
contributing factors. The study will provide help and assistance to
PFS outlet marketing companies to make their fuel station operation
safer. It will help health safety and environment (HSE) professionals
to arrest the gap available related to safety matters at PFS.
Abstract: The validity of Herzberg-s Two-Factor Theory of
Motivation was tested empirically by surveying 2372 chemical fiber
employees in 2012. In the valid sample of 1875 respondents, the
degree of overall job satisfaction was more than moderate. The most
highly valued components of job satisfaction were: “corporate image,"
“collaborative working atmosphere," and “supervisor-s expertise";
whereas the lowest mean score was 34.65 for “job rotation and
promotion." The top three job retention options rated by the
participants were “good image of the enterprise," “good
compensation," and “workplace is close to my residence." The overall
evaluation of the level of thriving facilitation workplace reached
almost to “mostly agree." For those participants who chose at least
one motivator as their job retention options had significantly greater
job satisfaction than those who chose only hygiene factors as their
retention options. Therefore, Herzberg-s Two-Factor Theory of
Motivation was proven valid in this study.
Abstract: In this work a new offline signature recognition system
based on Radon Transform, Fractal Dimension (FD) and Support Vector Machine (SVM) is presented. In the first step, projections of
original signatures along four specified directions have been performed using radon transform. Then, FDs of four obtained
vectors are calculated to construct a feature vector for each
signature. These vectors are then fed into SVM classifier for recognition of signatures. In order to evaluate the effectiveness of
the system several experiments are carried out. Offline signature
database from signature verification competition (SVC) 2004 is used
during all of the tests. Experimental result indicates that the proposed method achieved high accuracy rate in signature recognition.
Abstract: One of the popular methods for recognition of facial
expressions such as happiness, sadness and surprise is based on
deformation of facial features. Motion vectors which show these
deformations can be specified by the optical flow. In this method, for
detecting emotions, the resulted set of motion vectors are compared
with standard deformation template that caused by facial expressions.
In this paper, a new method is introduced to compute the quantity of
likeness in order to make decision based on the importance of
obtained vectors from an optical flow approach. For finding the
vectors, one of the efficient optical flow method developed by
Gautama and VanHulle[17] is used. The suggested method has been
examined over Cohn-Kanade AU-Coded Facial Expression Database,
one of the most comprehensive collections of test images available.
The experimental results show that our method could correctly
recognize the facial expressions in 94% of case studies. The results
also show that only a few number of image frames (three frames) are
sufficient to detect facial expressions with rate of success of about
83.3%. This is a significant improvement over the available methods.
Abstract: In this study, to compress ECG signals, KLT (Karhunen-
Loeve Transform) method has been used. The purpose of this method is to
perform effective ECG coding by a correlation between the length of frames
and the number of vectors of ECG signals.
Abstract: Logistics is part of the supply chain processes that
plans, implements, and controls the efficient and effective forward
and reverse flow and storage of goods, services, and related
information between the point of origin and the point of consumption
in order to meet customer requirements. This research aims to
investigate the current status and future direction of the use of
Information Technology (IT) for logistics, focusing on Supply Chain
Management (SCM) and E-Commerce adoption in Malaysia.
Therefore, this research stresses on the type of technology being
adopted, factors, benefits and barriers affecting the innovation in
SCM and E-Commerce technology adoption among Logistics
Service Providers (LSP). A mailed questionnaire survey was
conducted to collect data from 265 logistics companies in Johor. The
research revealed a high level of SCM technology adoption among
LSP as they had adopted SCM technology in various business
processes while they perceived a high level of benefits from SCM
adoption.
Abstract: This paper explores steady-state characteristics of
grid-connected doubly fed induction motor (DFIM) in case of unity
power factor operation. Based on the synchronized mathematical
model, analytic determination of the control laws is presented and
illustrated by various figures to understand the effect of the applied
rotor voltage on the speed and the active power. On other hand,
unlike previous works where the stator resistance was neglected, in
this work, stator resistance is included such that the equations can be
applied to small wind turbine generators which are becoming more
popular. Finally the work is crowned by integration of the studied
induction generator in a wind system where an open loop control is
proposed confers a remarkable simplicity of implementation
compared to the known methods.
Abstract: Supply Chain Management (SCM) is the integration
between manufacturer, transporter and customer in order to form one
seamless chain that allows smooth flow of raw materials, information
and products throughout the entire network that help in minimizing
all related efforts and costs. The main objective of this paper is to
develop a model that can accept a specified number of spare-parts
within the supply chain, simulating its inventory operations
throughout all stages in order to minimize the inventory holding
costs, base-stock, safety-stock, and to find the optimum quantity of
inventory levels, thereby suggesting a way forward to adapt some
factors of Just-In-Time to minimizing the inventory costs throughout
the entire supply chain. The model has been developed using Micro-
Soft Excel & Visual Basic in order to study inventory allocations in
any network of the supply chain. The application and reproducibility
of this model were tested by comparing the actual system that was
implemented in the case study with the results of the developed
model. The findings showed that the total inventory costs of the
developed model are about 50% less than the actual costs of the
inventory items within the case study.