Abstract: In this paper, a field oriented control (FOC) induction motor drive is presented. In order to eliminate the speed sensor, an adaptation algorithm for tuning the rotor speed is proposed. Based on the Model Reference Adaptive System (MRAS) scheme, the rotor speed is tuned to obtain an exact FOC induction motor drive. The reference and adjustable models, developed in stationary stator reference frame, are used in the MRAS scheme to estimate induction rotor speed from measured terminal voltages and currents. The Integral Proportional (IP) gains speed controller are tuned by a modern approach that is the Particle Swarm Optimization (PSO) algorithm in order to optimize the parameters of the IP controller. The use of PSO as an optimization algorithm makes the drive robust, with faster dynamic response, higher accuracy and insensitive to load variation. The proposed algorithm has been tested by numerical simulation, showing the capability of driving load.
Abstract: This study presents an active vibration control
technique to reduce the earthquake responses of a retained structural
system. The proposed technique is a synthesis of the adaptive input
estimation method (AIEM) and linear quadratic Gaussian (LQG)
controller. The AIEM can estimate an unknown system input online.
The LQG controller offers optimal control forces to suppress
wall-structural system vibration. The numerical results show robust
performance in the active vibration control technique.
Abstract: Many real-world optimization problems involve multiple conflicting objectives and the use of evolutionary algorithms to solve the problems has attracted much attention recently. This paper investigates the application of multi-objective optimization technique for the design of a Thyristor Controlled Series Compensator (TCSC)-based controller to enhance the performance of a power system. The design objective is to improve both rotor angle stability and system voltage profile. A Genetic Algorithm (GA) based solution technique is applied to generate a Pareto set of global optimal solutions to the given multi-objective optimisation problem. Further, a fuzzy-based membership value assignment method is employed to choose the best compromise solution from the obtained Pareto solution set. Simulation results are presented to show the effectiveness and robustness of the proposed approach.
Abstract: This paper presents the design, fabrication and
evaluation of magneto-rheological damper. Semi-active control
devices have received significant attention in recent years because
they offer the adaptability of active control devices without requiring
the associated large power sources. Magneto-Rheological (MR)
dampers are semi- active control devices that use MR fluids to
produce controllable dampers. They potentially offer highly reliable
operation and can be viewed as fail-safe in that they become passive
dampers if the control hardware malfunction. The advantage of MR
dampers over conventional dampers are that they are simple in
construction, compromise between high frequency isolation and
natural frequency isolation, they offer semi-active control, use very
little power, have very quick response, has few moving parts, have a
relax tolerances and direct interfacing with electronics. Magneto-
Rheological (MR) fluids are Controllable fluids belonging to the
class of active materials that have the unique ability to change
dynamic yield stress when acted upon by an electric or magnetic
field, while maintaining viscosity relatively constant. This property
can be utilized in MR damper where the damping force is changed by
changing the rheological properties of the fluid magnetically. MR
fluids have a dynamic yield stress over Electro-Rheological fluids
(ER) and a broader operational temperature range. The objective of
this papert was to study the application of an MR damper to vibration
control, design the vibration damper using MR fluids, test and
evaluate its performance. In this paper the Rheology and the theory
behind MR fluids and their use on vibration control were studied.
Then a MR vibration damper suitable for vehicle suspension was
designed and fabricated using the MR fluid. The MR damper was
tested using a dynamic test rig and the results were obtained in the
form of force vs velocity and the force vs displacement plots. The
results were encouraging and greatly inspire further research on the
topic.
Abstract: Optimization of cutting parameters important in precision machining in regards to efficiency and surface integrity of the machined part. Usually productivity and precision in machining is limited by the forces emanating from the cutting process. Due to the inherent varying nature of the workpiece in terms of geometry and material composition, the peak cutting forces vary from point to point during machining process. In order to increase productivity without compromising on machining accuracy, it is important to control these cutting forces. In this paper a fuzzy logic control algorithm is developed that can be applied in the control of peak cutting forces in milling of spherical surfaces using ball end mills. The controller can adaptively vary the feedrate to maintain allowable cutting force on the tool. This control algorithm is implemented in a computer numerical control (CNC) machine. It has been demonstrated that the controller can provide stable machining and improve the performance of the CNC milling process by varying feedrate.
Abstract: The main goal of the study is to analyze all relevant properties of the electro hydraulic systems and based on that to make a proper choice of the neural network control strategy that may be used for the control of the mechatronic system. A combination of electronic and hydraulic systems is widely used since it combines the advantages of both. Hydraulic systems are widely spread because of their properties as accuracy, flexibility, high horsepower-to-weight ratio, fast starting, stopping and reversal with smoothness and precision, and simplicity of operations. On the other hand, the modern control of hydraulic systems is based on control of the circuit fed to the inductive solenoid that controls the position of the hydraulic valve. Since this circuit may be easily handled by PWM (Pulse Width Modulation) signal with a proper frequency, the combination of electrical and hydraulic systems became very fruitful and usable in specific areas as airplane and military industry. The study shows and discusses the experimental results obtained by the control strategy of neural network control using MATLAB and SIMULINK [1]. Finally, the special attention was paid to the possibility of neuro-controller design and its application to control of electro-hydraulic systems and to make comparative with other kinds of control.
Abstract: One of the best ways for achievement of conventional
vehicle changing to hybrid case is trustworthy simulation result and
using of driving realities. For this object, in this paper, at first sevendegree-
of-freedom dynamical model of vehicle will be shown. Then
by using of statically model of engine, gear box, clutch, differential,
electrical machine and battery, the hybrid automobile modeling will
be down and forward simulation of vehicle for pedals to wheels
power transformation will be obtained. Then by design of a fuzzy
controller and using the proper rule base, fuel economy and
regenerative braking will be marked. Finally a series of
MATLAB/SIMULINK simulation results will be proved the
effectiveness of proposed structure.
Abstract: This paper proposes an effective adaptation learning
algorithm based on artificial neural networks for speed control of an
induction motor assumed to operate in a high-performance drives
environment. The structure scheme consists of a neural network
controller and an algorithm for changing the NN weights in order that
the motor speed can accurately track of the reference command. This
paper also makes uses a very realistic and practical scheme to
estimate and adaptively learn the noise content in the speed load
torque characteristic of the motor. The availability of the proposed
controller is verified by through a laboratory implementation and
under computation simulations with Matlab-software. The process is
also tested for the tracking property using different types of reference
signals. The performance and robustness of the proposed control
scheme have evaluated under a variety of operating conditions of the
induction motor drives. The obtained results demonstrate the
effectiveness of the proposed control scheme system performances,
both in steady state error in speed and dynamic conditions, was found
to be excellent and those is not overshoot.
Abstract: In this paper we propose an intelligent agent approach
to control the electric power grid at a smaller granularity in order to
give it self-healing capabilities. We develop a method using the
influence model to transform transmission substations into
information processing, analyzing and decision making (intelligent
behavior) units. We also develop a wireless communication method
to deliver real-time uncorrupted information to an intelligent
controller in a power system environment. A combined networking
and information theoretic approach is adopted in meeting both the
delay and error probability requirements. We use a mobile agent
approach in optimizing the achievable information rate vector and in
the distribution of rates to users (sensors). We developed the concept
and the quantitative tools require in the creation of cooperating semiautonomous
subsystems which puts the electric grid on the path
towards intelligent and self-healing system.
Abstract: In this work a dynamic model of a new quadrotor aerial
vehicle that is equipped with a tilt-wing mechanism is presented.
The vehicle has the capabilities of vertical take-off/landing (VTOL)
like a helicopter and flying horizontal like an airplane. Dynamic
model of the vehicle is derived both for vertical and horizontal flight
modes using Newton-Euler formulation. An LQR controller for the
vertical flight mode has also been developed and its performance
has been tested with several simulations.
Abstract: This paper presents a new hardware interface using a
microcontroller which processes audio music signals to standard
MIDI data. A technique for processing music signals by extracting
note parameters from music signals is described. An algorithm to
convert the voice samples for real-time processing without complex
calculations is proposed. A high frequency microcontroller as the
main processor is deployed to execute the outlined algorithm. The
MIDI data generated is transmitted using the EIA-232 protocol. The
analyses of data generated show the feasibility of using
microcontrollers for real-time MIDI generation hardware interface.
Abstract: This paper may be considered as combination of both pervasive computing and Differential GPS (global positioning satellite) which relates to control automatic traffic signals in such a
way as to pre-empt normal signal operation and permit lifesaving vehicles. Before knowing the arrival of the lifesaving vehicles from
the signal there is a chance of clearing the traffic. Traffic signal
preemption system includes a vehicle equipped with onboard computer system capable of capturing diagnostic information and
estimated location of the lifesaving vehicle using the information provided by GPS receiver connected to the onboard computer system
and transmitting the information-s using a wireless transmitter via a
wireless network. The fleet management system connected to a
wireless receiver is capable of receiving the information transmitted
by the lifesaving vehicle .A computer is also located at the
intersection uses corrected vehicle position, speed & direction
measurements, in conjunction with previously recorded data defining
approach routes to the intersection, to determine the optimum time to
switch a traffic light controller to preemption mode so that lifesaving
vehicles can pass safely. In case when the ambulance need to take a
“U" turn in a heavy traffic area we suggest a solution. Now we are
going to make use of computerized median which uses LINKED
BLOCKS (removable) to solve the above problem.
Abstract: The current methods of predictive controllers are
utilized for those processes in which the rate of output variations is
not high. For such processes, therefore, stability can be achieved by
implementing the constrained predictive controller or applying
infinite prediction horizon. When the rate of the output growth is
high (e.g. for unstable nonminimum phase process) the stabilization
seems to be problematic. In order to avoid this, it is suggested to
change the method in the way that: first, the prediction error growth
should be decreased at the early stage of the prediction horizon, and
second, the rate of the error variation should be penalized. The
growth of the error is decreased through adjusting its weighting
coefficients in the cost function. Reduction in the error variation is
possible by adding the first order derivate of the error into the cost
function. By studying different examples it is shown that using these
two remedies together, the closed-loop stability of unstable
nonminimum phase process can be achieved.
Abstract: This paper presents a speed fuzzy sliding mode
controller for a vector controlled induction machine (IM) fed by a
voltage source inverter (PWM).
The sliding mode based fuzzy control method is developed to
achieve fast response, a best disturbance rejection and to maintain a
good decoupling.
The problem with sliding mode control is that there is high
frequency switching around the sliding mode surface. The FSMC is
the combination of the robustness of Sliding Mode Control (SMC)
and the smoothness of Fuzzy Logic (FL). To reduce the torque
fluctuations (chattering), the sign function used in the conventional
SMC is substituted with a fuzzy logic algorithm.
The proposed algorithm was simulated by Matlab/Simulink
software and simulation results show that the performance of the
control scheme is robust and the chattering problem is solved.
Abstract: The main goal of the study is to analyze all relevant
properties of the electro hydraulic systems and based on that to make
a proper choice of the control strategy that may be used for the
control of the servomechanism system. A combination of electronic
and hydraulic systems is widely used since it combines the
advantages of both. Hydraulic systems are widely spread because of
their properties as accuracy, flexibility, high horsepower-to-weight
ratio, fast starting, stopping and reversal with smoothness and
precision, and simplicity of operations. On the other hand, the
modern control of hydraulic systems is based on control of the circuit
fed to the inductive solenoid that controls the position of the
hydraulic valve. Since this circuit may be easily handled by PWM
(Pulse Width Modulation) signal with a proper frequency, the
combination of electrical and hydraulic systems became very fruitful
and usable in specific areas as airplane and military industry.
The study shows and discusses the experimental results obtained
by the control strategy (classical feedback (PID) & neural network)
using MATLAB and SIMULINK [1]. Finally, the special attention
was paid to the possibility of neuro-controller design and its
application to control of electro-hydraulic systems and to make
comparative with classical control.
Abstract: The anti-lock braking systems installed on vehicles
for safe and effective braking, are high-order nonlinear and timevariant.
Using fuzzy logic controllers increase efficiency of such
systems, but impose a high computational complexity as well. The
main concept introduced by this paper is reducing computational
complexity of fuzzy controllers by deploying problem-solution data
structure. Unlike conventional methods that are based on
calculations, this approach is based on data oriented modeling.
Abstract: Adaptive control involves modifying the control law
used by the controller to cope with the fact that the parameters of the
system being controlled change drastically due to change in
environmental conditions or in system itself. This technique is based
on the fundamental characteristic of adaptation of living organism.
The adaptive control process is one that continuously and
automatically measures the dynamic behavior of plant, compares it
with the desired output and uses the difference to vary adjustable
system parameters or to generate an actuating signal in such a way so
that optimal performance can be maintained regardless of system
changes. This paper deals with application of model reference
adaptive control scheme in first order system. The rule which is used
for this application is MIT rule. This paper also shows the effect of
adaptation gain on the system performance. Simulation is done in
MATLAB and results are discussed in detail.
Abstract: In process control applications, above 90% of the
controllers are of PID type. This paper proposed a robust PI
controller with fractional-order integrator. The PI parameters were
obtained using classical Ziegler-Nichols rules but enhanced with the
application of error filter cascaded to the fractional-order PI. The
controller was applied on steam temperature process that was
described by FOPDT transfer function. The process can be classified
as lag dominating process with very small relative dead-time. The
proposed control scheme was compared with other PI controller
tuned using Ziegler-Nichols and AMIGO rules. Other PI controller
with fractional-order integrator known as F-MIGO was also
considered. All the controllers were subjected to set point change and
load disturbance tests. The performance was measured using Integral
of Squared Error (ISE) and Integral of Control Signal (ICO). The
proposed controller produced best performance for all the tests with
the least ISE index.
Abstract: In this paper the neural network-based controller is
designed for motion control of a mobile robot. This paper treats the
problems of trajectory following and posture stabilization of the
mobile robot with nonholonomic constraints. For this purpose the
recurrent neural network with one hidden layer is used. It learns
relationship between linear velocities and error positions of the
mobile robot. This neural network is trained on-line using the
backpropagation optimization algorithm with an adaptive learning
rate. The optimization algorithm is performed at each sample time to
compute the optimal control inputs. The performance of the proposed
system is investigated using a kinematic model of the mobile robot.
Abstract: In this paper, an effective sliding mode design is
applied to chaos synchronization. The proposed controller can make
the states of two identical modified Chua-s circuits globally
asymptotically synchronized. Numerical results are provided to show
the effectiveness and robustness of the proposed method.