Abstract: This paper proposes a direct power control for
doubly-fed induction machine for variable speed wind power
generation. It provides decoupled regulation of the primary side
active and reactive power and it is suitable for both electric energy
generation and drive applications. In order to control the power
flowing between the stator of the DFIG and the network, a decoupled
control of active and reactive power is synthesized using PI
controllers.The obtained simulation results show the feasibility
and the effectiveness of the suggested method
Abstract: An integrated vehicle dynamics control system is developed in this paper by a combination of active front steering (AFS) and direct yaw-moment control (DYC) based on fuzzy logic control. The control system has a hierarchical structure consisting of two layers. A fuzzy logic controller is used in the upper layer (yaw rate controller) to keep the yaw rate in its desired value. The yaw rate error and its rate of change are applied to the upper controlling layer as inputs, where the direct yaw moment control signal and the steering angle correction of the front wheels are the outputs. In the lower layer (fuzzy integrator), a fuzzy logic controller is designed based on the working region of the lateral tire forces. Depending on the directions of the lateral forces at the front wheels, a switching function is activated to adjust the scaling factor of the fuzzy logic controller. Using a nonlinear seven degrees of freedom vehicle model, the simulation results illustrate considerable improvements which are achieved in vehicle handling through the integrated AFS/DYC control system in comparison with the individual AFS or DYC controllers.
Abstract: This paper presents a solution for the behavioural animation of autonomous virtual agent navigation in virtual environments. We focus on using Dempster-Shafer-s Theory of Evidence in developing visual sensor for virtual agent. The role of the visual sensor is to capture the information about the virtual environment or identifie which part of an obstacle can be seen from the position of the virtual agent. This information is require for vitual agent to coordinate navigation in virtual environment. The virual agent uses fuzzy controller as a navigation system and Fuzzy α - level for the action selection method. The result clearly demonstrates the path produced is reasonably smooth even though there is some sharp turn and also still not diverted too far from the potential shortest path. This had indicated the benefit of our method, where more reliable and accurate paths produced during navigation task.
Abstract: Chaiyaphum Starch Co. Ltd. is one of many starch
manufacturers that has introduced machinery to aid in manufacturing.
Even though machinery has replaced many elements and is now a
significant part in manufacturing processes, problems that must be
solved with respect to current process flow to increase efficiency still
exist. The paper-s aim is to increase productivity while maintaining
desired quality of starch, by redesigning the flipping machine-s
mechanical control system which has grossly low functional lifetime.
Such problems stem from the mechanical control system-s bearings,
as fluids and humidity can access into said bearing directly, in
tandem with vibrations from the machine-s function itself. The wheel
which is used to sense starch thickness occasionally falls from its
shaft, due to high speed rotation during operation, while the shaft
may bend from impact when processing dried bread. Redesigning its
mechanical control system has increased its efficiency, allowing
quality thickness measurement while increasing functional lifetime
an additional 62 days.
Abstract: This article presents the evolution and technological changes implemented on the full scale simulators developed by the Simulation Department of the Instituto de Investigaciones Eléctricas1 (Mexican Electric Research Institute) and located at different training centers around the Mexican territory, and allows US to know the last updates, basically from the input/output view point, of the current simulators at some facilities of the electrical sector as well as the compatible industry of the electrical manufactures and industries such as Comision Federal de Electricidad (CFE*, The utility Mexican company). Tendencies of these developments and impact within the operators- scope are also presented.
Abstract: To achieve the desired specifications of gain and
phase margins for plants with time-delay that stabilized with FO-PID
controller a lead compensator is designed. At first the range of
controlled system stability based on stability boundary criteria is
determined. Using stability boundary locus method in frequency
domain the fractional order controller parameters are tuned and then
with drawing bode diagram in frequency domain accessing to desired
gain and phase margin are shown. Numerical examples are given to
illustrate the shapes of the stabilizing region and to show the design
procedure.
Abstract: In this paper; we are interested principally in dynamic modelling of quadrotor while taking into account the high-order nonholonomic constraints in order to develop a new control scheme as well as the various physical phenomena, which can influence the dynamics of a flying structure. These permit us to introduce a new state-space representation. After, the use of Backstepping approach for the synthesis of tracking errors and Lyapunov functions, a sliding mode controller is developed in order to ensure Lyapunov stability, the handling of all system nonlinearities and desired tracking trajectories. Finally simulation results are also provided in order to illustrate the performances of the proposed controller.
Abstract: This paper introduces a new method called ARPDC (Advanced Robust Parallel Distributed Compensation) for automatic control of nonlinear systems. This method improves a quality of robust control by interpolating of robust and optimal controller. The weight of each controller is determined by an original criteria function for model validity and disturbance appreciation. ARPDC method is based on nonlinear Takagi-Sugeno (T-S) fuzzy systems and Parallel Distributed Compensation (PDC) control scheme. The relaxed stability conditions of ARPDC control of nominal system have been derived. The advantages of presented method are demonstrated on the inverse pendulum benchmark problem. From comparison between three different controllers (robust, optimal and ARPDC) follows, that ARPDC control is almost optimal with the robustness close to the robust controller. The results indicate that ARPDC algorithm can be a good alternative not only for a robust control, but in some cases also to an adaptive control of nonlinear systems.
Abstract: A digital system is proposed for low power 100-
channel neural recording system in this paper, which consists of 100
amplifiers, 100 analog-to-digital converters (ADC), digital controller
and baseband, transceiver for data link and RF command link. The
proposed system is designed in a 0.18 μm CMOS process and 65 nm
CMOS process.
Abstract: This paper is focused on issues of nonlinear dynamic process modeling and model-based predictive control of a fed-batch sugar crystallization process applying the concept of artificial neural networks as computational tools. The control objective is to force the operation into following optimal supersaturation trajectory. It is achieved by manipulating the feed flow rate of sugar liquor/syrup, considered as the control input. A feed forward neural network (FFNN) model of the process is first built as part of the controller structure to predict the process response over a specified (prediction) horizon. The predictions are supplied to an optimization procedure to determine the values of the control action over a specified (control) horizon that minimizes a predefined performance index. The control task is rather challenging due to the strong nonlinearity of the process dynamics and variations in the crystallization kinetics. However, the simulation results demonstrated smooth behavior of the control actions and satisfactory reference tracking.
Abstract: The most common type of controller being used in
the industry is PI(D) controller which has been used since 1945 and
is still being widely used due to its efficiency and simplicity. In
most cases, the PI(D) controller was tuned without taking into
consideration of the effect of actuator saturation. In real processes,
the most common actuator which is valve will act as constraint and
restrict the controller output. Since the controller is not designed to
encounter saturation, the process may windup and consequently
resulted in large oscillation or may become unstable. Usually, an
antiwindup compensator is added to the feedback control loop to
reduce the deterioration effect of integral windup. This research
aims to specifically control processes with constraints. The
proposed method was applied to two different types of food
processes, which are blending and spray drying. Simulations were
done using MATLAB and the performances of the proposed
method were compared with other conventional methods. The
proposed technique was able to control the processes and avoid
saturation such that no anti windup compensator is needed.
Abstract: In this paper a PID control strategy using neural
network adaptive RASP1 wavelet for WECS-s control is proposed.
It is based on single layer feedforward neural networks with hidden
nodes of adaptive RASP1 wavelet functions controller and an infinite
impulse response (IIR) recurrent structure. The IIR is combined by
cascading to the network to provide double local structure resulting
in improving speed of learning. This particular neuro PID controller
assumes a certain model structure to approximately identify the
system dynamics of the unknown plant (WECS-s) and generate the
control signal. The results are applied to a typical turbine/generator
pair, showing the feasibility of the proposed solution.
Abstract: This paper presents a systematic approach for designing Unified Power Flow Controller (UPFC) based supplementary damping controllers for damping low frequency oscillations in a single-machine infinite-bus power system. Detailed investigations have been carried out considering the four alternatives UPFC based damping controller namely modulating index of series inverter (mB), modulating index of shunt inverter (mE), phase angle of series inverter (δB ) and phase angle of the shunt inverter (δE ). The design problem of the proposed controllers is formulated as an optimization problem and Real- Coded Genetic Algorithm (RCGA) is employed to optimize damping controller parameters. Simulation results are presented and compared with a conventional method of tuning the damping controller parameters to show the effectiveness and robustness of the proposed design approach.
Abstract: In this paper an algorithm for fast wavelength calibration of Optical Spectrum Analyzers (OSAs) using low power reference gas spectra is proposed. In existing OSAs a reference spectrum with low noise for precise detection of the reference extreme values is needed. To generate this spectrum costly hardware with high optical power is necessary. With this new wavelength calibration algorithm it is possible to use a noisy reference spectrum and therefore hardware costs can be cut. With this algorithm the reference spectrum is filtered and the key information is extracted by segmenting and finding the local minima and maxima. Afterwards slope and offset of a linear correction function for best matching the measured and theoretical spectra are found by correlating the measured with the stored minima. With this algorithm a reliable wavelength referencing of an OSA can be implemented on a microcontroller with a calculation time of less than one second.
Abstract: This paper presents an approach for the design of
fuzzy logic power system stabilizers using genetic algorithms. In the
proposed fuzzy expert system, speed deviation and its derivative
have been selected as fuzzy inputs. In this approach the parameters of
the fuzzy logic controllers have been tuned using genetic algorithm.
Incorporation of GA in the design of fuzzy logic power system
stabilizer will add an intelligent dimension to the stabilizer and
significantly reduces computational time in the design process. It is
shown in this paper that the system dynamic performance can be
improved significantly by incorporating a genetic-based searching
mechanism. To demonstrate the robustness of the genetic based
fuzzy logic power system stabilizer (GFLPSS), simulation studies on
multimachine system subjected to small perturbation and three-phase
fault have been carried out. Simulation results show the superiority
and robustness of GA based power system stabilizer as compare to
conventionally tuned controller to enhance system dynamic
performance over a wide range of operating conditions.
Abstract: This paper presents a procedure for modeling and tuning the parameters of Thyristor Controlled Series Compensation (TCSC) controller in a multi-machine power system to improve transient stability. First a simple transfer function model of TCSC controller for stability improvement is developed and the parameters of the proposed controller are optimally tuned. Genetic algorithm (GA) is employed for the optimization of the parameter-constrained nonlinear optimization problem implemented in a simulation environment. By minimizing an objective function in which the oscillatory rotor angle deviations of the generators are involved, transient stability performance of the system is improved. The proposed TCSC controller is tested on a multi-machine system and the simulation results are presented. The nonlinear simulation results validate the effectiveness of proposed approach for transient stability improvement in a multimachine power system installed with a TCSC. The simulation results also show that the proposed TCSC controller is also effective in damping low frequency oscillations.
Abstract: The paper is concerned with the state examination as
well as the problems during the post surgical (orthopedic)
rehabilitation of the knee and ankle joint. An observation of the
current appliances for a passive rehabilitation devices is presented.
The major necessary and basic features of the intelligent
rehabilitation devices are considered. An approach for a new
intelligent appliance is suggested. The main advantages of the device
are: both active as well as passive rehabilitation of the patient based
on the human - patient reactions and a real time feedback. The basic
components: controller; electrical motor; encoder, force – torque
sensor are discussed in details. The main modes of operation of the
device are considered.
Abstract: The problem of robust fuzzy control for a class of
nonlinear fuzzy impulsive singular perturbed systems with
time-varying delay is investigated by employing Lyapunov functions.
The nonlinear delay system is built based on the well-known T–S
fuzzy model. The so-called parallel distributed compensation idea is
employed to design the state feedback controller. Sufficient conditions
for global exponential stability of the closed-loop system are derived
in terms of linear matrix inequalities (LMIs), which can be easily
solved by LMI technique. Some simulations illustrate the effectiveness
of the proposed method.
Abstract: In this study, we used shape memory alloys as
actuators to build a biomorphic robot which can imitate the motion of
an earthworm. The robot can be used to explore in a narrow space.
Therefore we chose shape memory alloys as actuators. Because of the
small deformation of a wire shape memory alloy, spiral shape memory
alloys are selected and installed both on the X axis and Y axis (each
axis having two shape memory alloys) to enable the biomorphic robot
to do reciprocating motion. By the mechanism we designed, the robot
can increase the distance as it moves in a duty cycle. In addition, two
shape memory alloys are added to the robot head for controlling right
and left turns. By sending pulses through the I/O card from the
controller, the signals are then amplified by a driver to heat the shape
memory alloys in order to make the SMA shrink to pull the mechanism
to move.
Abstract: This paper addresses the controller synthesis problem of discrete-time switched positive systems with bounded time-varying delays. Based on the switched copositive Lyapunov function approach, some necessary and sufficient conditions for the existence of state-feedback controller are presented as a set of linear programming and linear matrix inequality problems, hence easy to be verified. Another advantage is that the state-feedback law is independent on time-varying delays and initial conditions. A numerical example is provided to illustrate the effectiveness and feasibility of the developed controller.