Abstract: The Greater Athens Area (GAA) faces photochemical
and particulate pollution episodes as a result of the combined effects
of local pollutant emissions, regional pollution transport, synoptic
circulation and topographic characteristics. The area has undergone
significant changes since the Athens 2004 Olympic Games because
of large scale infrastructure works that lead to the shift of population
to areas previously characterized as rural, the increase of the traffic
fleet and the operation of highways. However, few recent modelling
studies have been performed due to the lack of an accurate, updated
emission inventory. The photochemical modelling system
MM5/CAMx was applied in order to study the photochemical and
particulate pollution characteristics above the GAA for two distinct
ten-day periods in the summer of 2006 and 2010, where air pollution
episodes occurred. A new updated emission inventory was used
based on official data. Comparison of modeled results with
measurements revealed the importance and accuracy of the new
Athens emission inventory as compared to previous modeling
studies. The model managed to reproduce the local meteorological
conditions, the daily ozone and particulates fluctuations at different
locations across the GAA. Higher ozone levels were found at
suburban and rural areas as well as over the sea at the south of the
basin. Concerning PM10, high concentrations were computed at the
city centre and the southeastern suburbs in agreement with measured
data. Source apportionment analysis showed that different sources
contribute to the ozone levels, the local sources (traffic, port
activities) affecting its formation.
Abstract: This paper presents an extensive review of literature
relevant to the modelling techniques adopted in sediment yield and
hydrological modelling. Several studies relating to sediment yield are
discussed. Many research areas of sedimentation in rivers, runoff and
reservoirs are presented. Different types of hydrological models,
different methods employed in selecting appropriate models for
different case studies are analysed. Applications of evolutionary
algorithms and artificial intelligence techniques are discussed and
compared especially in water resources management and modelling.
This review concentrates on Genetic Programming (GP) and fully
discusses its theories and applications. The successful applications of
GP as a soft computing technique were reviewed in sediment
modelling. Some fundamental issues such as benchmark,
generalization ability, bloat, over-fitting and other open issues
relating to the working principles of GP are highlighted. This paper
concludes with the identification of some research gaps in
hydrological modelling and sediment yield.
Abstract: This paper integrates Octagon and Square Search
pattern (OCTSS) motion estimation algorithm into H.264/AVC
(Advanced Video Coding) video codec in Adaptive Group of Pictures
(AGOP) mode. AGOP structure is computed based on scene change
in the video sequence. Octagon and square search pattern block-based
motion estimation method is implemented in inter-prediction process
of H.264/AVC. Both these methods reduce bit rate and computational
complexity while maintaining the quality of the video sequence
respectively. Experiments are conducted for different types of video
sequence. The results substantially proved that the bit rate,
computation time and PSNR gain achieved by the proposed method
is better than the existing H.264/AVC with fixed GOP and AGOP.
With a marginal gain in quality of 0.28dB and average gain in bitrate
of 132.87kbps, the proposed method reduces the average computation
time by 27.31 minutes when compared to the existing state-of-art
H.264/AVC video codec.
Abstract: The present study examined how translation teachers
develop final tests as measures for checking on the quality of
students’ academic translation in Iranian context. To achieve this
goal, thirty experienced male and female translation teachers from the
four types of the universities offering the program were invited to an
in-depth 30-minute one-session semi-structured interview. The
responses provided showed how much discrepancy exists among the
Iranian translation teachers (as developers of final translation tests),
who are least informed with the current translation evaluation
methods. It was also revealed that the criteria they use for developing
such tests and scoring student translations are not theory-driven but
are highly subjective, mainly based on their personal experience and
intuition. Hence, the quality and accountability of such tests are under
serious question. The results also confirmed that the dominant
method commonly and currently practiced is the purely essay-type
format. To remedy the situation, some suggestions are in order. As
part of the solution, to improve the reliability and validity of such
tests, the present summative, product-oriented evaluation should be
accompanied with some formative, process-oriented methods of
evaluation. Training the teachers and helping them get acquainted
with modern principles of translation evaluation as well as the
existing models, and rating scales does improve the quality of
academic translation evaluation.
Abstract: In this study, we have collected cases with adipocere
formation, which were from the South Delhi region (average room
temperature 27-390C) and autopsied at our centre. Details of the
circumstances of the death, cause and time of death, surrounding
environment and demographic profile of the deceased were taken into
account. Total 16 cases were included in this study. Adipocere
formation was predominantly present over cheeks, shoulder, breast,
flanks, buttocks, and thighs. Out of 16, 11 cases were found in a dry
atmosphere, 5 cases were brought from the water. There were 5 cases
in which adipocere formation was seen in less than 2 days, and
among them, in 1 case, as early as one day. This study showed that
adipocere formation can be seen as early as 1 day in a hot and humid
environment.
Abstract: This study identified the hypothesised relationship
between creative experience, and revisit intention of handmade
oriental parasol umbrella in Kaohsiung, Taiwan. A face-to-face
questionnaire survey was administered in Meinong town, Kaohsiung.
The components of creative experience were found as “sense of
achievement”, “unique learning” and “interaction with instructors” in
creative tourism. The result also revealed significant positive
relationships between creative experience and revisit intention in
handmade activities. This paper provides additional suggestions for
enhancing revisit intention and guidance regarding creative tourism.
Abstract: The use of information technology in education have
changed not only the learners learning style but also the way they
taught, where nowadays learners are connected with diversity of
information sources with means of knowledge available everywhere.
The advantage of network wireless technologies and mobility
technologies used in the education and learning processes lead to
mobile learning as a new model of learning technology. Currently,
most of mobile learning applications are developed for the formal
education and learning environment. Despite the long history and
large amount of research on mobile learning and instruction design
model still there is a need of well-defined process in designing
mobile learning applications. Based on this situation, this paper
emphasizes on identifying instruction design phase’s considerations
and influencing factors in developing mobile learning application.
This set of instruction design steps includes analysis, design,
development, implementation, evaluation and continuous has been
built from a literature study, with focus on standards for learning,
mobile application software quality and guidelines. The effort is part
of an Omani-funded research project investigating the development,
adoption and dissemination of mobile learning in Oman.
Abstract: In the present study, analysis of heat transfer is carried
out in the slip flow region for the fluid flowing between two parallel
plates by employing the asymmetric heat fluxes at surface of the
plates. The flow is assumed to be hydrodynamically and thermally
fully developed for the analysis. The second order velocity slip and
viscous dissipation effects are considered for the analysis. Closed
form expressions are obtained for the Nusselt number as a function of
Knudsen number and modified Brinkman number. The limiting
condition of the present prediction for Kn = 0, Kn2 = 0, and Brq1 = 0
is considered and found to agree well with other analytical results.
Abstract: The advancements in technology allow the
development of a new system that can continuously measure surface
soil erosion. Continuous soil erosion measurements are required in
order to comprehend the erosional processes and propose effective
and efficient conservation measures to mitigate surface erosion.
Mitigating soil erosion, especially in Mediterranean countries such as
Greece, is essential in order to maintain environmental and
agricultural sustainability. In this paper, we present the Automated
Soil Erosion Monitoring System (ASEMS) that measures surface soil
erosion along with other factors that impact erosional process.
Specifically, this system measures ground level changes (surface soil
erosion), rainfall, air temperature, soil temperature, and soil moisture.
Another important innovation is that the data will be collected by
remote communication. In addition, stakeholder’s awareness is a key
factor to help reduce any environmental problem. The different
dissemination activities that were utilized are described. The overall
outcomes were the development of a new innovative system that can
measure erosion very accurately. These data from the system help
study the process of erosion and find the best possible methods to
reduce erosion. The dissemination activities enhance the stakeholders
and public's awareness on surface soil erosion problems and will lead
to the adoption of more effective soil erosion conservation practices
in Greece.
Abstract: It is well-known that, using principal weak flatness
property, some important monoids are characterized, such as regular
monoids, left almost regular monoids, and so on. In this article, we
define a generalization of principal weak flatness called GP-Flatness,
and will characterize monoids by this property of their right (Rees
factor) acts. Also we investigate new classes of monoids called
generally regular monoids and generally left almost regular monoids.
Abstract: The development of composite materials and the
related design and manufacturing technologies is one of the most
important advances in the history of materials. Composites are
multifunctional materials having unprecedented mechanical and
physical properties that can be tailored to meet the requirements of a
particular application. Some composites also exhibit great resistance
to high-temperature corrosion, oxidation, and wear. Polymers are
widely used indoors and outdoors, therefore they are exposed to a
chemical environment which may include atmospheric oxygen, acidic
fumes, acidic rain, moisture heat and thermal shock, ultra-violet light,
high energy radiation, etc. Different polymers are affected differently
by these factors even though the amorphous polymers are more
sensitive. Ageing is also important and it is defined as the process of
deterioration of engineering materials resulting from the combined
effects of atmospheric radiation, heat, oxygen, water, microorganisms
and other atmospheric factors.
Abstract: This article presents the main results of a numerical
investigation on the uncertainty of dynamic response of structures
with statistically correlated random damping Gamma distributed. A
computational method based on a Linear Statistical Model (LSM) is
implemented to predict second order statistics for the response of a
typical industrial building structure. The significance of random
damping with correlated parameters and its implications on the
sensitivity of structural peak response in the neighborhood of a
resonant frequency are discussed in light of considerable ranges of
damping uncertainties and correlation coefficients. The results are
compared to those generated using Monte Carlo simulation
techniques. The numerical results obtained show the importance of
damping uncertainty and statistical correlation of damping
coefficients when obtaining accurate probabilistic estimates of
dynamic response of structures. Furthermore, the effectiveness of the
LSM model to efficiently predict uncertainty propagation for
structural dynamic problems with correlated damping parameters is
demonstrated.
Abstract: The study conducted a simulation of the effect of sea
water to the bonding capacity of GFRP sheet on the concrete beams
using a simulation tank. Fiber reinforced polymer (FRP) has been
developed and applied in many fields civil engineering structures on
the new structures and also for strengthening of the deteriorated
structures. The FRP has advantages such as its corrosion resistance as
well as high tensile strength to weight ratio. Compared to the other
FRP materials, Glass composed FRP (GFRP) is relatively cheaper.
GFRP sheet is applied externally by bonding it on the concrete surface.
The studies regarding the application of GFRP sheet have been
conducted such as strengthening system, bonding behavior of GFRP
sheet including the application as reinforcement in new structures. For
application to the structures with direct contact to sea environment, a
study regarding the effect of sea water to the bonding capacity of
GFRP sheet is important to be clarified. To achieve the objective of the
study, a series of concrete beams strengthened with GFRP sheet on
extreme tension surface were prepared. The beams then were stored on
the sea water tank for six months. Results indicated the bonding
capacity decreased after six month exposed to the sea water.
Abstract: The Green Urban Lab took the form of public
installations that were placed at various locations in four cities in
Cyprus. These installations - through which a series of events,
activities, workshops and research took place - were the main tools in
regenerating a series of urban public spaces in Cyprus. The purpose
of this project was to identify issues and opportunities related to
public space and to offer guidelines on how design and participatory
democracy improvements could strengthen civil society, while
raising the quality of the urban public scene. Giant inflatable
structures were injected in important urban fragments in order to
accommodate series of events. The design and playful installation
generated a wide community engagement. The fluid presence of the
installations acted as a catalyst for social interaction. They were
accessed and viewed effortlessly and surprisingly, creating
opportunities to rediscover public spaces.
Abstract: The aim of this study was to determine the factor
structure and psychometric properties (i.e., reliability and convergent
validity) of the Employee Trust Scale, a newly created instrument by
the researchers. The Employee Trust Scale initially contained 82
items to measure employees’ trust toward their supervisors. A sample
of 818 (343 females, 449 males) employees were selected randomly
from public and private organization sectors in Kota Kinabalu,
Sabah, Malaysia. Their ages ranged from 19 to 67 years old with a
mean of 34.55 years old. Their average tenure with their current
employer was 11.2 years (s.d. = 7.5 years). The respondents were
asked to complete the Employee Trust Scale, as well as a managerial
trust questionnaire from Mishra. The exploratory factor analysis on
employees’ trust toward their supervisor’s extracted three factors,
labeled ‘trustworthiness’ (32 items), ‘position status’ (11 items) and
‘relationship’ (6 items) which accounted for 62.49% of the total
variance. Trustworthiness factors were re-categorized into three sub
factors: competency (11 items), benevolence (8 items) and integrity
(13 items). All factors and sub factors of the scales demonstrated
clear reliability with internal consistency of Cronbach’s Alpha above
.85. The convergent validity of the Scale was supported by an
expected pattern of correlations (positive and significant correlation)
between the score of all factors and sub factors of the scale and the
score on the managerial trust questionnaire, which measured the same
construct. The convergent validity of Employee Trust Scale was
further supported by the significant and positive inter-correlation
between the factors and sub factors of the scale. The results suggest
that the Employee Trust Scale is a reliable and valid measure.
However, further studies need to be carried out in other groups of
sample as to further validate the Scale.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: In recent years, the power system has been changed
and a flexible power pricing system such as demand response has been
sought in Japan. The demand response system works simply in the
household sector and the owner as the decision-maker, can benefit
from power saving. On the other hand, the execution of demand
response in the office building is more complex than in the household
because various people such as owners, building administrators and
occupants are involved in the decision-making process. While the
owners benefit from demand saving, the occupants are exposed to
restricted benefits of a demand-saved environment. One of the reasons
is that building systems are usually under centralized management and
each occupant cannot choose freely whether to participate in demand
response or not. In addition, it is unclear whether incentives give
occupants the motivation to participate. However, the recent
development of IT and building systems enables the personalized
control of the office environment where each occupant can control the
lighting level or temperature individually. Therefore, it can be possible
to have a system which each occupant can make a decision of whether
or not to participate in demand response in the office building. This study investigates personal responses to demand response
requests, under the condition where each occupant can adjust their
brightness individually in their workspace. Once workers participate
in the demand response, their desk-lights are automatically turned off.
The participation rates in the demand response events are compared
among four groups, which are divided by different motivation, the
presence, or absence of incentives and the method of participation. The
result shows that there are significant differences of participation rates
in demand response event between four groups. The method of
participation has a large effect on the participation rate. The “Opt-out”
groups where the occupants are automatically enrolled in a demand
response event if they do not express non-participation have the
highest participation rate in the four groups. Incentives also have an
effect on the participation rate. This study also reports on the impact of low illumination office
environment on the occupants, such as stress or fatigue. The
electrocardiogram and the questionnaire are used to investigate the
autonomic nervous activity and subjective fatigue symptoms of the
occupants. There is no big difference between dim workspace during
demand response event and bright workspace in autonomic nervous
activity and fatigue.
Abstract: The activation volume of 6082T6 aluminum is
investigated at different temperatures for grain size variants. The
deformation activation volume was computed on the basis of the
relationship between the Boltzmann’s constant k, the testing
temperatures, the material strain rate sensitivity and the material yield
stress grain size variants. The material strain rate sensitivity is
computed as a function of yield stress and strain rate grain size
variants. The effect of the material strain rate sensitivity and the
deformation activation volume of 6082T6 aluminum at different
temperatures of 3-D grain are discussed. It is shown that the strain rate sensitivities and activation volume
are negative for the grain size variants during the deformation of
nanostructured materials. It is also observed that the activation
volume vary in different ways with the equivalent radius, semi minor
axis radius, semi major axis radius and major axis radius. From the
obtained results it is shown that the variation of activation volume
increase and decrease with the testing temperature. It was revealed
that, increase in strain rate sensitivity led to decrease in activation
volume whereas increase in activation volume led to decrease in
strain rate sensitivity.
Abstract: The aim of optimization of store management is not
only designing the situation of store management itself including its
equipment, technology and operation. In optimization of store
management we need to consider also synchronizing of
technological, transport, store and service operations throughout the
whole process of logistic chain in such a way that a natural flow of
material from provider to consumer will be achieved the shortest
possible way, in the shortest possible time in requested quality and
quantity and with minimum costs. The paper deals with the
application of the queuing theory for optimization of warehouse
processes. The first part refers to common information about the
problematic of warehousing and using mathematical methods for
logistics chains optimization. The second part refers to preparing a
model of a warehouse within queuing theory. The conclusion of the
paper includes two examples of using queuing theory in praxis.
Abstract: In this study, we examine some spectral properties
of non-selfadjoint matrix-valued difference equations consisting of
a polynomial-type Jost solution. The aim of this study is to
investigate the eigenvalues and spectral singularities of the difference
operator L which is expressed by the above-mentioned difference
equation. Firstly, thanks to the representation of polynomial type Jost
solution of this equation, we obtain asymptotics and some analytical
properties. Then, using the uniqueness theorems of analytic functions,
we guarantee that the operator L has a finite number of eigenvalues
and spectral singularities.