Abstract: Equipment miniaturisation offers several opportunities such as an increased surface-to-volume ratio and higher heat transfer coefficients. However, moving towards small-diameter channels demands extra attention to fouling, reliability and stable operation of the system. The present investigation explores possibilities to enhance the stability of the once-through micro evaporator by reducing its flow boiling induced pressure fluctuations. Experimental comparison shows that the measured reduction factor approaches a theoretically derived value. Pressure fluctuations are reduced by a factor of ten in the solid conical channel and a factor of 15 in the porous conical channel. This presumably leads to less backflow and therefore to a better flow control.
Abstract: Rise/span ratio has been mentioned as one of the
reasons which contribute to the lower buckling load as compared to
the Classical theory buckling load but this ratio has not been quantified
in the equation. The purpose of this study was to determine a more
realistic buckling load by quantifying the effect of the rise/span ratio
because experiments have shown that the Classical theory
overestimates the load. The buckling load equation was derived based
on the theorem of work done and strain energy. Thereafter, finite
element modeling and simulation using ABAQUS was done to
determine the variables that determine the constant in the derived
equation. The rise/span was found to be the determining factor of the
constant in the buckling load equation. The derived buckling load
correlates closely to the load obtained from experiments.
Abstract: Integrated Total Quality Management (TQM) with
Lean Manufacturing (LM) is a system comprises of TQM with LM
principles and is associated with financial and nonfinancial
performance measurement indicators. The ultimate goal of this
system is to focus on achieving total customer satisfaction by
removing eight wastes available in any process in an organization.
A survey questionnaire was developed and distributed to 30 highly
active automotive vendors in Malaysia and analyzed by PASW
Statistics 18. It was found out that these vendors have been
practicing and measuring the effectiveness TQM and LM
implementation. More involvement of all Malaysian automotive
vendors will represent the exact status of current Malaysian
automotive industry in implementing TQM and LM and can
determine whether the industry is ready for integrated TQM and
LM system. This is the first study that combined 4 awards
practices, ISO/TS16949, Toyota Production System and
SAEJ4000.
Abstract: Information hiding for authenticating and verifying the content integrity of the multimedia has been exploited extensively in the last decade. We propose the idea of using genetic algorithm and non-deterministic dependence by involving the un-watermarkable coefficients for digital image authentication. Genetic algorithm is used to intelligently select coefficients for watermarking in a DCT based image authentication scheme, which implicitly watermark all the un-watermarkable coefficients also, in order to thwart different attacks. Experimental results show that such intelligent selection results in improvement of imperceptibility of the watermarked image, and implicit watermarking of all the coefficients improves security against attacks such as cover-up, vector quantization and transplantation.
Abstract: Carrier mobility has become the most important
characteristic of high speed low dimensional devices. Due to
development of very fast switching semiconductor devices, speed of
computer and communication equipment has been increasing day by
day and will continue to do so in future. As the response of any
device depends on the carrier motion within the devices, extensive
studies of carrier mobility in the devices has been established
essential for the growth in the field of low dimensional devices.
Small-signal ac transport of degenerate two-dimensional hot
electrons in GaAs quantum wells is studied here incorporating
deformation potential acoustic, polar optic and ionized impurity
scattering in the framework of heated drifted Fermi-Dirac carrier
distribution. Delta doping is considered in the calculations to
investigate the effects of double delta doping on millimeter and submillimeter
wave response of two dimensional hot electrons in GaAs
nanostructures. The inclusion of delta doping is found to enhance
considerably the two dimensional electron density which in turn
improves the carrier mobility (both ac and dc) values in the GaAs
quantum wells thereby providing scope of getting higher speed
devices in future.
Abstract: The purpose of this study is to identify and evaluate
the scale of implementation of Just-In-Time (JIT) in the different industrial sectors in the Middle East. This study analyzes the empirical data collected by a questionnaire survey distributed to
companies in three main industrial sectors in the Middle East, which
are: food, chemicals and fabrics. The following main hypotheses is formulated and tested: (The requirements of JIT application differ
according to the type of industrial sector).Descriptive statistics and Box plot analysis were used to examine the hypotheses. This study indicates a reasonable evidence for accepting the main hypotheses. It
reveals that there is no standard way to adopt JIT as a production system. But each industrial sector should concentrate in the
investment on critical requirements that differ according to the nature
and strategy of production followed in that sector.
Abstract: Inconel718 has been widely used as a super alloy in aerospace application due to the high strength at elevated temperatures, satisfactory oxidation resistance and heat corrosion resistance. In this study, the Inconel718 has been fabricated using high technology of Metal Injection Molding (MIM) process due to the cost effective technique for producing small, complex and precision parts in high volume compared with conventional method through machining. Through MIM, the binder system is one of the most important criteria in order to successfully fabricate the Inconel718. Even though, the binder system is a temporary, but failure in the selection and removal of the binder system will affect on the final properties of the sintered parts. Therefore, the binder system based on palm oil derivative which is palm stearin has been formulated and developed to replace the conventional binder system. The rheological studies of the mixture between the powder and binders system have been determined properly in order to be successful during injection into injection molding machine. After molding, the binder holds the particles in place. The binder system has to be removed completely through debinding step. During debinding step, solvent debinding and thermal pyrolysis has been used to remove completely of the binder system. The debound part is then sintered to give the required physical and mechanical properties. The results show that the properties of the final sintered parts fulfill the Standard Metal Powder Industries Federation (MPIF) 35 for MIM parts.
Abstract: This paper describes the evolution of language
politics and the part played by political leaders with reference to
the Dravidian parties in Tamil Nadu. It explores the interesting
evolution from separatism to coalition in sustaining the values of
parliamentary democracy and federalism. It seems that the
appropriation of language politics is fully ascribed to the DMK
leadership under Annadurai and Karunanidhi. For them, the Tamil
language is a self-determining power, a terrain of nationhood, and
a perennial source of social and political powers. The DMK
remains a symbol of Tamil nationalist party playing language
politics in the interest of the Tamils. Though electoral alliances
largely determine the success, the language politics still has
significant space in the politics of Tamil Nadu. Ironically, DMK
moves from the periphery to centre for getting national recognition
for the Tamils as well as for its own maximization of power. The
evolution can be seen in two major phases as: language politics for
party building; and language politics for state building with three
successive political processes, namely, language politics in the
process of separatism, representative politics and coalition. The
much pronounced Dravidian Movement is radical enough to
democratize the party ideology to survive the spirit of
parliamentary democracy. This has secured its own rewards in
terms of political power. The political power provides the means to
achieve the social and political goal of the political party.
Language politics and leadership pattern actualized this trend
though the movement is shifted from separatism to coalition.
Abstract: This study focuses on bureau management
technologies and information systems in developing countries.
Developing countries use such systems which facilitate executive and
organizational functions through the utilization of bureau
management technologies and provide the executive staff with
necessary information.
The concepts of data and information differ from each other in
developing countries, and thus the concepts of data processing and
information processing are different. Symbols represent ideas,
objects, figures, letters and numbers. Data processing system is an
integrated system which deals with the processing of the data related
to the internal and external environment of the organization in order
to make decisions, create plans and develop strategies; it goes
without saying that this system is composed of both human beings
and machines. Information is obtained through the acquisition and
the processing of data. On the other hand, data are raw
communicative messages. Within this framework, data processing
equals to producing plausible information out of raw data.
Organizations in developing countries need to obtain information
relevant to them because rapid changes in the organizational arena
require rapid access to accurate information. The most significant
role of the directors and managers who work in the organizational
arena is to make decisions. Making a correct decision is possible only
when the directors and managers are equipped with sound ideas and
appropriate information. Therefore, acquisition, organization and
distribution of information gain significance. Today-s organizations
make use of computer-assisted “Management Information Systems"
in order to obtain and distribute information.
Decision Support System which is closely related to practice is an
information system that facilitates the director-s task of making
decisions. Decision Support System integrates human intelligence,
information technology and software in order to solve the complex
problems. With the support of the computer technology and software
systems, Decision Support System produces information relevant to
the decision to be made by the director and provides the executive
staff with supportive ideas about the decision.
Artificial Intelligence programs which transfer the studies and
experiences of the people to the computer are called expert systems.
An expert system stores expert information in a limited area and can
solve problems by deriving rational consequences.
Bureau management technologies and information systems in
developing countries create a kind of information society and
information economy which make those countries have their places
in the global socio-economic structure and which enable them to play
a reasonable and fruitful role; therefore it is of crucial importance to
make use of information and management technologies in order to
work together with innovative and enterprising individuals and it is
also significant to create “scientific policies" based on information
and technology in the fields of economy, politics, law and culture.
Abstract: The effect of seed inoculation by VA- mycorrhiza and
different levels of phosphorus fertilizer on growth and yield of
sunflower (Azargol cultivar) was studied in experiment farm of
Islamic Azad University, Karaj Branch during 2008 growing season.
The experiment treatments were arranged in factorial based on a
complete randomized block design with three replications. Four
phosphorus fertilizer levels of 25%, 50% 75% and 100% P
recommended with two levels of Mycorrhiza: with and without
Mycorrhiza (control) were assigned in a factorial combination.
Results showed that head diameter, number of seeds in head, seed
yield and oil yield were significantly higher in inoculated plants than
in non-inoculated plants. Head diameter, number of seeds in head,
1000 seeds weight, biological yield, seed yield and oil yield increased
with increasing P level above 75% P recommended in non-inoculated
plants, whereas no significant difference was observed between 75%
and 100% P recommended. The positive effect of mycorrhizal
inoculation decreased with increasing P levels due to decreased
percent root colonization at higher P levels. According to the results
of this experiment, application of mycorrhiza in present of 50% P
recommended had an appropriate performance and could increase
seed yield and oil production to an acceptable level, so it could be
considered as a suitable substitute for chemical phosphorus fertilizer
in organic agricultural systems.
Abstract: Recently the usefulness of Concept Abduction, a novel non-monotonic inference service for Description Logics (DLs), has been argued in the context of ontology-based applications such as semantic matchmaking and resource retrieval. Based on tableau calculus, a method has been proposed to realize this reasoning task in ALN, a description logic that supports simple cardinality restrictions as well as other basic constructors. However, in many ontology-based systems, the representation of ontology would require expressive formalisms for capturing domain-specific constraints, this language is not sufficient. In order to increase the applicability of the abductive reasoning method in such contexts, we would like to present in the scope of this paper an extension of the tableaux-based algorithm for dealing with concepts represented inALCQ, the description logic that extends ALN with full concept negation and quantified number restrictions.
Abstract: This paper presents the results of an experimental
investigation carried out to evaluate the shrinkage of High Strength
Concrete. High Strength Concrete is made by partially replacement of
cement by flyash and silica fume. The shrinkage of High Strength
Concrete has been studied using the different types of coarse and fine
aggregates i.e. Sandstone and Granite of 12.5 mm size and Yamuna
and Badarpur Sand. The Mix proportion of concrete is 1:0.8:2.2 with
water cement ratio as 0.30. Superplasticizer dose @ of 2% by weight
of cement is added to achieve the required degree of workability in
terms of compaction factor.
From the test results of the above investigation it can be concluded
that the shrinkage strain of High Strength Concrete increases with
age. The shrinkage strain of concrete with replacement of cement by
10% of Flyash and Silica fume respectively at various ages are more
(6 to 10%) than the shrinkage strain of concrete without Flyash and
Silica fume. The shrinkage strain of concrete with Badarpur sand as
Fine aggregate at 90 days is slightly less (10%) than that of concrete
with Yamuna Sand. Further, the shrinkage strain of concrete with
Granite as Coarse aggregate at 90 days is slightly less (6 to 7%) than
that of concrete with Sand stone as aggregate of same size. The
shrinkage strain of High Strength Concrete is also compared with that
of normal strength concrete. Test results show that the shrinkage
strain of high strength concrete is less than that of normal strength
concrete.
Abstract: This paper describes technological possibilities to
enhance methane productionin the anaerobic stabilization of wastewater treatment plant excess sludge. This objective can be achieved by the addition of waste residues: crude glycerol from biodiesel production and residues from fishery. The addition
ofglycerol in an amount by weight of 2 – 5% causes enhancement of methane production of about 250 – 400%. At the same time the
percentage increase of total solids concentration in the outgoing sludge is ten or more times less. The containment of methane in
biogas is higher in case of admixed substrate.
Abstract: In this research, an anaerobic co-digestion using decanter cake from palm oil mill industry to improve the biogas production from frozen seafood wastewater is studied using Continuously Stirred Tank Reactor (CSTR) process. The experiments were conducted in laboratory-scale. The suitable Hydraulic Retention Time (HRT) was observed in CSTR experiments with 24 hours of mixing time using the mechanical mixer. The HRT of CSTR process impacts on the efficiency of biogas production. The best performance for biogas production using CSTR process was the anaerobic codigestion for 20 days of HRT with the maximum methane production rate of 1.86 l/d and the average maximum methane production of 64.6%. The result can be concluded that the decanter cake can improve biogas productivity of frozen seafood wastewater.
Abstract: Hand gesture is one of the typical methods used in
sign language for non-verbal communication. It is most commonly
used by people who have hearing or speech problems to
communicate among themselves or with normal people. Various sign
language systems have been developed by manufacturers around the
globe but they are neither flexible nor cost-effective for the end
users. This paper presents a system prototype that is able to
automatically recognize sign language to help normal people to
communicate more effectively with the hearing or speech impaired
people. The Sign to Voice system prototype, S2V, was developed
using Feed Forward Neural Network for two-sequence signs
detection. Different sets of universal hand gestures were captured
from video camera and utilized to train the neural network for
classification purpose. The experimental results have shown that
neural network has achieved satisfactory result for sign-to-voice
translation.
Abstract: Advances in technology (e.g. the internet,
telecommunication) and political changes (fewer trade barriers and an
enlarged European Union, ASEAN, NAFTA and other organizations)
have led to develop international competition and expand into new
markets. Companies in Thailand, Asia and around the globe are
increasingly being pressured on price and for faster time to enter the
market. At the same time, new markets are appearing and many
companies are looking for changes and shifts in their domestic
markets. These factors have enabled the rapid growth for companies
and globalizing many different business activities during the product
development process from research and development (R&D) to
production.
This research will show and clarify methods how to develop
global product. Also, it will show how important is a global product
impact into Thai Economy development.
Abstract: In the present study, development of salbutamol
sulphate nanoparticles that adhere to gastric mucus was investigated.
Salbutamol sulphate has low bioavailability due to short transit time in
gastric. It also has a positive surface charge that provides hurdles to be
encapsulated by the positively strong mucoadhesive polymer of
chitosan. To overcome the difficulties, the surface charge of active
ingredient was modified using several nonionic and anionic
stomach-specific polymers. The nanoparticles were prepared using
ionotropic gelation technique. The evaluation involved determination
of particle size, zeta potential, entrapment efficiency, in vitro drug
release and in vitro mucoadhesion test. Results exhibited that the use
of anionic alginate polymer was more satisfactory than that of
nonionic polymer. Characteristics of the particles was nano-size, high
encapsulation efficiency, fulfilled the drug release requirements and
adhesive towards stomach for around 11 hours. This result shows that
the salbutamol sulphate nanoparticles can be utilized for improvement
its delivery.
Abstract: Sleep stage scoring is the process of classifying the
stage of the sleep in which the subject is in. Sleep is classified into
two states based on the constellation of physiological parameters.
The two states are the non-rapid eye movement (NREM) and the
rapid eye movement (REM). The NREM sleep is also classified into
four stages (1-4). These states and the state wakefulness are
distinguished from each other based on the brain activity. In this
work, a classification method for automated sleep stage scoring
based on a single EEG recording using wavelet packet decomposition
was implemented. Thirty two ploysomnographic recording from the
MIT-BIH database were used for training and validation of the
proposed method. A single EEG recording was extracted and
smoothed using Savitzky-Golay filter. Wavelet packets
decomposition up to the fourth level based on 20th order Daubechies
filter was used to extract features from the EEG signal. A features
vector of 54 features was formed. It was reduced to a size of 25 using
the gain ratio method and fed into a classifier of regression trees. The
regression trees were trained using 67% of the records available. The
records for training were selected based on cross validation of the
records. The remaining of the records was used for testing the
classifier. The overall correct rate of the proposed method was found
to be around 75%, which is acceptable compared to the techniques in
the literature.
Abstract: Heavy metal pollution is an environmental concern.
Phytoremediation is a low-cost, environmental-friendly approach to
solve this problem. Mustard has the potential in reducing heavy metal
contents in soils. Among mustard (Brassica juncea (L.) Czern &
Coss) genotypes in Sri Lanka, accessions 7788, 8831 and 5088 give
significantly a high yield. Therefore, present study was conducted to
quantify the phytoextractive potential among these local mustard
accessions and to assess the interaction of heavy metals, Pb, Co, Mn
on phytoextraction. A pot experiment was designed with acid washed
sand (quartz) and a series of heavy metal solutions of 0, 25, 50, 75
and 100 μg/g. Experiment was carried out with factorial
experimental design. Mustard accessions were tolerant to heavy
metals and could be successfully used in removal of Pb, Co and Mn
and they are capable of accumulating significant quantities of heavy
metals in vegetative and reproductive organs. The order of the
accumulative potential of Pb, Co and Mn in mustard accessions is,
root > shoot >seed.
Abstract: The use of renewable energy sources incl. biogas has become topical in accordance with the increasing demand for energy, decrease of fossil energy resources and the efforts to reduce greenhouse gas emissions as well as to increase energy independence from the territories where fossil energy resources are available.
As the technologies of biogas production from agricultural biomass develop, risk assessment and risk management become necessary for farms producing such a renewable energy. The need for risk assessments has become particularly topical when discussions on changing the biogas policy in the EU take place, which may influence the development of the sector in the future, as well as the operation of existing biogas facilities and their income level.
The current article describes results of the risk assessment for farms producing biomass from agriculture biomass in Latvia, the risk assessment system included 24 risks, that affect the whole biogas production process and the obtained results showed the high significance of political and production risks.