Abstract: Fractional Fourier Transform is a powerful tool,
which is a generalization of the classical Fourier Transform. This
paper provides a mathematical relation relating the span in Fractional
Fourier domain with the amplitude and phase functions of the signal,
which is further used to study the variation of quality factor with
different values of the transform order. It is seen that with the
increase in the number of transients in the signal, the deviation of
average Fractional Fourier span from the frequency bandwidth
increases. Also, with the increase in the transient nature of the signal,
the optimum value of transform order can be estimated based on the
quality factor variation, and this value is found to be very close to
that for which one can obtain the most compact representation. With
the entire mathematical analysis and experimentation, we consolidate
the fact that Fractional Fourier Transform gives more optimal
representations for a number of transform orders than Fourier
transform.
Abstract: Hardness of the widely used structural steel is of vital
importance since it may help in the determination of many
mechanical properties of a material under loading situations. In order
to obtain reliable information for design, properties homogeneity
should be validated. In the current study the hardness variation over
the different diameters of the same AISI 4140 bar is investigated.
Measurements were taken on the two faces of the stock at equally
spaced eight sectors and fifteen layers. Statistical and graphical
analysis are performed to asses the distribution of hardness
measurements over the specified area. Hardness measurements
showed some degree of dispersion with about ± 10% of its nominal
value provided by manufacturer. Hardness value is found to have a
slight decrease trend as the diameter is reduced. However, an
opposite behavior is noticed regarding the sequence of the sector
indicating a nonuniform distribution over the same area either on the
same face or considering the corresponding sector on the other face
(cross section) of the same material bar.
Abstract: The evaluation of unit cell neutronic parameters and
lifetime for some innovant reactors without on sit-refuling will be
held in this work. the behavior of some small and medium reactors
without on site refueling with triso and cermet fuel. For the FBNR
long life except we propose to change the enrichment of the Cermet
MFE to 9%. For the AFPR reactor we can see that the use of the
Cermet MFE can extend the life of this reactor but to maintain the
same life period for AFPR-SC we most use burnup poison to have the
same slope for Kinf (Burnup). PFPWR50 cell behaves almost in
same way using both fuels Cermet and TRISO. So we can conclude
that PFPWR50 reactor, with CERMET Fuel, is kept among the long
cycle reactors and with the new configuration we avoid subcriticality
at the beginning of cycle. The evaluation of unit cell neutronic
parameters reveals a good agreement with the goal of BWR-PB
concept. It is found out that the Triso fuel assembly lifetime can be
extended for a reasonably long period without being refueled,
approximately up to 48GWd/t burnup. Using coated particles fuels
with the Cermet composition can be more extended the fuel assembly
life time, approximately 52 GWd/t.
Abstract: Many digital signal processing, techniques have been used to automatically distinguish protein coding regions (exons) from non-coding regions (introns) in DNA sequences. In this work, we have characterized these sequences according to their nonlinear dynamical features such as moment invariants, correlation dimension, and largest Lyapunov exponent estimates. We have applied our model to a number of real sequences encoded into a time series using EIIP sequence indicators. In order to discriminate between coding and non coding DNA regions, the phase space trajectory was first reconstructed for coding and non-coding regions. Nonlinear dynamical features are extracted from those regions and used to investigate a difference between them. Our results indicate that the nonlinear dynamical characteristics have yielded significant differences between coding (CR) and non-coding regions (NCR) in DNA sequences. Finally, the classifier is tested on real genes where coding and non-coding regions are well known.
Abstract: Project selection problems on management
information system (MIS) are often considered a multi-criteria
decision-making (MCDM) for a solving method. These problems
contain two aspects, such as interdependencies among criteria and
candidate projects and qualitative and quantitative factors of projects.
However, most existing methods reported in literature consider these
aspects separately even though these two aspects are simultaneously
incorporated. For this reason, we proposed a hybrid method using
analytic network process (ANP) and fuzzy logic in order to represent
both aspects. We then propose a goal programming model to conduct
an optimization for the project selection problems interpreted by a
hybrid concept. Finally, a numerical example is conducted as
verification purposes.
Abstract: The accelerated growth in aircraft industries desire
effectual schemes, programs, innovative designs of advanced systems
to accomplishing the augmenting need for home-free air
transportation. In this paper, a contemporary conceptual design of an
airplane has been proposed without landing gear systems in order to
reducing accidents, time consumption, and to eliminating drawbacks
by using superconducting levitation phenomenon. This invention of
an airplane with superconductive material coating, on the solar plexus
region assist to reduce weight by approximately 4% of the total takeoff
weight, and cost effective. Moreover, we conjectured that
superconductor landing system reduces ground friction, mission fuel,
total drag, take-off and landing distance.
Abstract: In today-s information age, numbers of organizations
are still arguing on capitalizing the values of Information Technology
(IT) and Knowledge Management (KM) to which individuals can
benefit from and effective communication among the individuals can
be established. IT exists in enabling positive improvement for
communication among knowledge workers (k-workers) with a
number of social network technology domains at workplace. The
acceptance of digital discourse in sharing of knowledge and
facilitating the knowledge and information flows at most of the
organizations indeed impose the culture of knowledge sharing in
Digital Social Networks (DSN). Therefore, this study examines
whether the k-workers with IT background would confer an effect on
the three knowledge characteristics -- conceptual, contextual, and
operational. Derived from these three knowledge characteristics, five
potential factors will be examined on the effects of knowledge
exchange via e-mail domain as the chosen query. It is expected, that
the results could provide such a parameter in exploring how DSN
contributes in supporting the k-workers- virtues, performance and
qualities as well as revealing the mutual point between IT and KM.
Abstract: In this paper a novel approach for generalized image
retrieval based on semantic contents is presented. A combination of
three feature extraction methods namely color, texture, and edge
histogram descriptor. There is a provision to add new features in
future for better retrieval efficiency. Any combination of these
methods, which is more appropriate for the application, can be used
for retrieval. This is provided through User Interface (UI) in the
form of relevance feedback. The image properties analyzed in this
work are by using computer vision and image processing algorithms.
For color the histogram of images are computed, for texture cooccurrence
matrix based entropy, energy, etc, are calculated and for
edge density it is Edge Histogram Descriptor (EHD) that is found.
For retrieval of images, a novel idea is developed based on greedy
strategy to reduce the computational complexity. The entire system
was developed using AForge.Imaging (an open source product),
MATLAB .NET Builder, C#, and Oracle 10g. The system was tested
with Coral Image database containing 1000 natural images and
achieved better results.
Abstract: This paper presents a generalized form of the
mechanistic deconvolution technique (GMD) to modeling image sensors applicable in various pan–tilt planes of view. The mechanistic deconvolution technique (UMD) is modified with the
given angles of a pan–tilt plane of view to formulate constraint parameters and characterize distortion effects, and thereby, determine
the corrected image data. This, as a result, does not require experimental setup or calibration. Due to the mechanistic nature of
the sensor model, the necessity for the sensor image plane to be
orthogonal to its z-axis is eliminated, and it reduces the dependency on image data. An experiment was constructed to evaluate the
accuracy of a model created by GMD and its insensitivity to changes in sensor properties and in pan and tilt angles. This was compared
with a pre-calibrated model and a model created by UMD using two sensors with different specifications. It achieved similar accuracy
with one-seventh the number of iterations and attained lower mean error by a factor of 2.4 when compared to the pre-calibrated and
UMD model respectively. The model has also shown itself to be robust and, in comparison to pre-calibrated and UMD model, improved the accuracy significantly.
Abstract: A laboratory study on the influence of compactive
effort on expansive black cotton specimens treated with up to 8%
ordinary Portland cement (OPC) admixed with up to 8% bagasse ash
(BA) by dry weight of soil and compacted using the energies of the
standard Proctor (SP), West African Standard (WAS) or
“intermediate” and modified Proctor (MP) were undertaken. The
expansive black cotton soil was classified as A-7-6 (16) or CL using
the American Association of Highway and Transportation Officials
(AASHTO) and Unified Soil Classification System (USCS),
respectively. The 7day unconfined compressive strength (UCS)
values of the natural soil for SP, WAS and MP compactive efforts are
286, 401 and 515kN/m2 respectively, while peak values of 1019,
1328 and 1420kN/m2 recorded at 8% OPC/ 6% BA, 8% OPC/ 2% BA
and 6% OPC/ 4% BA treatments, respectively were less than the
UCS value of 1710kN/m2 conventionally used as criterion for
adequate cement stabilization. The soaked California bearing ratio
(CBR) values of the OPC/BA stabilized soil increased with higher
energy level from 2, 4 and 10% for the natural soil to Peak values of
55, 18 and 8% were recorded at 8% OPC/4% BA 8% OPC/2% BA
and 8% OPC/4% BA, treatments when SP, WAS and MP compactive
effort were used, respectively. The durability of specimens was
determined by immersion in water. Soils treatment at 8% OPC/ 4%
BA blend gave a value of 50% resistance to loss in strength value
which is acceptable because of the harsh test condition of 7 days
soaking period specimens were subjected instead of the 4 days
soaking period that specified a minimum resistance to loss in strength
of 80%. Finally An optimal blend of is 8% OPC/ 4% BA is
recommended for treatment of expansive black cotton soil for use as
a sub-base material.
Abstract: Education, as the most important resource in any country, has multiplying effects on all facets of development in a society. The new social realities, particularly the interplay between democratization of education; unprecedented developments in IT sector; emergence of knowledge society, liberalization of economy and globalization have greatly influenced the educational process of all nations. This turbulence entails upon education to undergo dramatic changes to keep up with the new expectations. Growth of entrepreneurship among Indian women is highly important for empowering them and this is highly essential for socio-economic development of a society. Unfortunately in India there is poor acceptance of entrepreneurship among women as unfounded myths and fears restrain them to be enterprising. To remove these inhibitions, education system needs to be re-engineered to make entrepreneurship more acceptable. This paper empirically analyses the results of a survey done on around 500 female graduates in North India to measure and evaluate various entrepreneurial traits present in them. A formative model has been devised in this context, which should improve the teaching-learning process in our education system, which can lead to sustainable growth of women entrepreneurship in India.
Abstract: This paper focuses on issues of engagement by staff in professional development related to the delivery of e-learning. The paper reports on findings drawn from a New Zealand research project which is producing a sector-wide framework for professional development in tertiary e-learning. The research findings indicate that staff engaged in e-learning in tertiary institutions is not making the most effective use of the professional development opportunities available to them; rather they seem to gain their knowledge and support from a variety of informal means. This is despite an emphasis on the provision of professional development opportunities by both Government Policies and Institutions themselves. The conclusion drawn from the findings is that institutional approaches to professional development for e-learning do not yet fully reflect the demands and constraints that working in a digital context impose.
Abstract: Motion capturing technology has been used for quite a
while and several research has been done within this area. Nevertheless,
we discovered open issues within current motion capturing
environments. In this paper we provide a state-of-the-art overview of
the addressed research areas and show issues with current motion
capturing environments. Observations, interviews and questionnaires
have been used to reveal the challenges actors are currently facing in
a motion capturing environment. Furthermore, the idea to create a
more immersive motion capturing environment to improve the acting
performances and motion capturing outcomes as a potential solution
is introduced. It is hereby the goal to explain the found open issues
and the developed ideas which shall serve for further research as a
basis. Moreover, a methodology to address the interaction and
systems design issues is proposed. A future outcome could be that
motion capture actors are able to perform more naturally, especially
if using a non-body-worn solution.
Abstract: A low bit rate still image compression scheme by
compressing the indices of Vector Quantization (VQ) and generating
residual codebook is proposed. The indices of VQ are compressed by
exploiting correlation among image blocks, which reduces the bit per
index. A residual codebook similar to VQ codebook is generated that
represents the distortion produced in VQ. Using this residual
codebook the distortion in the reconstructed image is removed,
thereby increasing the image quality. Our scheme combines these two
methods. Experimental results on standard image Lena show that our
scheme can give a reconstructed image with a PSNR value of 31.6 db
at 0.396 bits per pixel. Our scheme is also faster than the existing VQ
variants.
Abstract: Rapid growth of distance learning resulted in
importance to conduct research on students- satisfaction with distance
learning because differences in students- satisfaction might influence
educational opportunities for learning in a relevant Web-based
environment. In line with this, this paper deals with satisfaction of
students with distance module at Faculty of organizational sciences
(FOS) in Serbia as well as some factors affecting differences in their
satisfaction . We have conducted a research on a population of 68
first-year students of distance learning studies at FOS. Using
statistical techniques, we have found out that there is no significant
difference in students- satisfaction with distance learning module
between men and women. In the same way, we also concluded that
there is a difference in satisfaction with distance learning module
regarding to student-s perception of opportunity to gain knowledge as
the classic students.
Abstract: The aim of this paper is to rank the impact of Object
Oriented(OO) metrics in fault prediction modeling using Artificial
Neural Networks(ANNs). Past studies on empirical validation of
object oriented metrics as fault predictors using ANNs have focused
on the predictive quality of neural networks versus standard
statistical techniques. In this empirical study we turn our attention to
the capability of ANNs in ranking the impact of these explanatory
metrics on fault proneness. In ANNs data analysis approach, there is
no clear method of ranking the impact of individual metrics. Five
ANN based techniques are studied which rank object oriented
metrics in predicting fault proneness of classes. These techniques are
i) overall connection weights method ii) Garson-s method iii) The
partial derivatives methods iv) The Input Perturb method v) the
classical stepwise methods. We develop and evaluate different
prediction models based on the ranking of the metrics by the
individual techniques. The models based on overall connection
weights and partial derivatives methods have been found to be most
accurate.
Abstract: The private theme parks are gradually surpassing
public-owned scenic areas after many years of development and have
become a mainstream choice for domestic tourists. Previous studies
show that visitors from different backgrounds differ in consumer
behavior and satisfaction factors. An understanding of visitor
satisfaction is therefore of extreme importance to operators of
privately-owned theme parks. Importance-Performance Analysis (IPA)
is used to measure consumer's potential satisfaction with services and
has become a widely used management tool for strength and weakness
analysis for brands, products, services and point of sales. As IPA has
so far not been used to evaluate the visitor satisfaction with
privately-owned theme parks, in this study the IPA method is used to
analyze visitor satisfaction with Janfusun Fancyworld (one of the most
popular private theme parks in Taiwan) and to rank visitor focus and
satisfaction on/in theme park facilities and services. Results of the
analysis provide private theme park operators with an understanding
of user or consumer demands as well as an assessment of the quality of
services currently offered.
Abstract: In this document, we have proposed a robust
conceptual strategy, in order to improve the robustness against the manufacturing defects and thus the reliability of logic CMOS circuits. However, in order to enable the use of future CMOS
technology nodes this strategy combines various types of design:
DFR (Design for Reliability), techniques of tolerance: hardware
redundancy TMR (Triple Modular Redundancy) for hard error
tolerance, the DFT (Design for Testability. The Results on largest ISCAS and ITC benchmark circuits show that our approach improves
considerably the reliability, by reducing the key factors, the area costs and fault tolerance probability.
Abstract: Flat double-layer grid is from category of space structures that are formed from two flat layers connected together with diagonal members. Increased stiffness and better seismic resistance in relation to other space structures are advantages of flat double layer space structures. The objective of this study is assessment and calculation of Behavior factor of flat double layer space structures. With regarding that these structures are used widely but Behavior factor used to design these structures against seismic force is not determined and exact, the necessity of study is obvious. This study is theoretical. In this study we used structures with span length of 16m and 20 m. All connections are pivotal. ANSYS software is used to non-linear analysis of structures.
Abstract: Flood management is one of the important fields in
urban storm water management. Floods are influenced by the
increase of huge storm event, or improper planning of the area. This study mainly provides the flood protection in four stages; planning,
flood event, responses and evaluation. However it is most effective then flood protection is considered in planning/design and
evaluation stages since both stages represent the land development of the area. Structural adjustments are often more reliable than nonstructural
adjustments in providing flood protection, however
structural adjustments are constrained by numerous factors such as
political constraints and cost. Therefore it is important to balance
both adjustments with the situation. The technical decisions provided
will have to be approved by the higher-ups who have the power to
decide on the final solution. Costs however, are the biggest factor in
determining the final decision. Therefore this study recommends
flood protection system should have been integrated and enforces
more in the early stages (planning and design) as part of the storm
water management plan. Factors influencing the technical decisions
provided should be reduced as low as possible to avoid a reduction in
the expected performance of the proposed adjustments.