Abstract: An unconventional composite inorganic ceramic
membrane capable of enhancing carbon dioxide emission decline was
fabricated and tested at laboratory scale in conformism to various
environmental guidelines and also to mitigate the effect of global
warming. A review of the existing membrane technologies for carbon
capture including the relevant gas transport mechanisms is presented.
Single gas permeation experiments using silica modified ceramic
membrane with internal diameter 20mm, outside diameter 25mm and
length of 368mm deposited on a macro porous support was carried
out to investigate individual gas permeation behaviours at different
pressures at room temperature. Membrane fabrication was achieved
using after a dip coating method. Nitrogen, Carbon dioxide, Argon,
Oxygen and Methane pure gases were used to investigate their
individual permeation rates at various pressures. Results show that
the gas flow rate increases with pressure drop. However above a
pressure of 3bar, CO2 permeability ratio to that of the other gases
indicated control of a more selective surface adsorptive transport
mechanism.
Abstract: We evaluate the performance of a numerical method
for global optimization of expensive functions. The method is using a
response surface to guide the search for the global optimum. This
metamodel could be based on radial basis functions, kriging, or a
combination of different models. We discuss how to set the cyclic
parameters of the optimization method to get a balance between local
and global search. We also discuss the eventual problem with Runge
oscillations in the response surface.
Abstract: Coal fly ash is formed as a solid waste product from
the combustion of coal in coal fired power stations. Huge amounts of
fly ash are produced globally every year and are predicted to
increase. Nowadays, less than half of the fly ash is used as a raw
material for cement manufacturing, construction and the rest of it is
disposed as a waste causing yet another environmental concern. For
this reason, the recycling of this kind of slurries into useful materials
is quite important in terms of economical and environmental aspects.
The purpose of this study is to evaluate the Orhaneli and
Tuncbilek coal fly ashes for utilization in some industrial
applications. Therefore the mineralogical and chemical compositions
of these fly ashes were analyzed by X-ray fluorescence spectroscopy,
ourier-transform infrared spectrometer, and X-ray diffraction. The
silicon (Si) and aluminum (Al) in the fly ashes were activated by
alkali fusion technique with sodium hydroxide. The obtained extracts
were analyzed for Si and Al content by inductively coupled plasma
optical emission spectrometry.
Abstract: Introduction: Researchers globally have strived to explore diverse factors that augment the continuation and uptake of family planning methods. Clients’ satisfaction is one of the core determinants facilitating continuation of family planning methods. There is a major debate yet scanty evidence to contrast public and private sectors with respect to client satisfaction. The objective of this study is to compare quality-of-care provided by public and private sectors of Pakistan through a client satisfaction lens. Methods: We used Pakistan Demographic Heath Survey 2012-13 dataset on 3133 women. Ten different multivariate models were made. to explore the relationship between client satisfaction and dependent outcome after adjusting for all known confounding factors and results are presented as OR and AOR (95% CI). Results: Multivariate analyses showed that clients were less satisfied in contraceptive provision from private sector as compared to public sector (AOR 0.92, 95% CI 0.63-1.68) even though the result was not statistically significant. Clients were more satisfied from private sector as compared to the public sector with respect to other determinants of quality-of-care follow-up care (AOR 3.29, 95% CI 1.95-5.55), infection prevention (AOR 2.41, 95% CI 1.60-3.62), counseling services (AOR 2.01, 95% CI 1.27-3.18, timely treatment (AOR 3.37, 95% CI 2.20-5.15), attitude of staff (AOR 2.23, 95% CI 1.50-3.33), punctuality of staff (AOR 2.28, 95% CI 1.92-4.13), timely referring (AOR 2.34, 95% CI 1.63-3.35), staff cooperation (AOR 1.75, 95% CI 1.22-2.51) and complications handling (AOR 2.27, 95% CI 1.56-3.29). Discussion: Public sector has successfully attained substantial satisfaction levels with respect to provision of contraceptives, but it contrasts previous literature from a multi country studies. Our study though in is concordance with a study from Tanzania where public sector was more likely to offer family planning services to clients as compared to private facilities. Conclusion: In majority of the developing countries, public sector is more involved in FP service provision; however, in Pakistan clients’ satisfaction in private sector is more, which opens doors for public-private partnerships and collaboration in the near future.
Abstract: A reliability-based methodology which uses structural demand hazard curves to consider the increment of the ductility demands of structures with tilting is proposed. The approach considers the effect of two orthogonal components of the ground motions as well as the influence of soil-structure interaction. The approach involves the calculation of ductility demand hazard curves for symmetric systems and, alternatively, for systems with different degrees of asymmetry. To get this objective, demand hazard curves corresponding to different global ductility demands of the systems are calculated. Next, Uniform Exceedance Rate Spectra (UERS) are developed for a specific mean annual rate of exceedance value. Ratios between UERS corresponding to asymmetric and to symmetric systems located in soft soil of the valley of Mexico are obtained. Results indicate that the ductility demands corresponding to tilted structures may be several times higher than those corresponding to symmetric structures, depending on several factors such as tilting angle and vibration period of structure and soil.
Abstract: Freelancing in IT has seen an increased popularity
during the last years mainly because of the fast Internet adoption in
the countries with emerging economies, correlated with the
continuous seek for reduced development costs as well with the rise
of online platforms which address planning, coordination and various
development tasks. This paper conducts an overview of the most
relevant Freelance Marketplaces available and studies the market
structure, distribution of the workforce and trends in IT freelancing.
Abstract: The distribution of a single global clock across a chip
has become the major design bottleneck for high performance VLSI
systems owing to the power dissipation, process variability and multicycle
cross-chip signaling. A Network-on-Chip (NoC) architecture
partitioned into several synchronous blocks has become a promising
approach for attaining fine-grain power management at the system
level. In a NoC architecture the communication between the blocks is
handled asynchronously. To interface these blocks on a chip
operating at different frequencies, an asynchronous FIFO interface is
inevitable. However, these asynchronous FIFOs are not required if
adjacent blocks belong to the same clock domain. In this paper, we
have designed and analyzed a 16-bit asynchronous micropipelined
FIFO of depth four, with the awareness of place and route on an
FPGA device. We have used a commercially available Spartan 3
device and designed a high speed implementation of the
asynchronous 4-phase micropipeline. The asynchronous FIFO
implemented on the FPGA device shows 76 Mb/s throughput and a
handshake cycle of 109 ns for write and 101.3 ns for read at the
simulation under the worst case operating conditions (voltage =
0.95V) on a working chip at the room temperature.
Abstract: Typically, virtual communities exhibit the well-known
phenomenon of participation inequality, which means that only a
small percentage of users is responsible of the majority of
contributions. However, the sustainability of the community requires
that the group of active users must be continuously nurtured with new
users that gain expertise through a participation process. This paper
analyzes the time evolution of Open Source Software (OSS)
communities, considering users that join/abandon the community
over time and several topological properties of the network when
modeled as a social network. More specifically, the paper analyzes
the role of those users rejoining the community and their influence in
the global characteristics of the network.
Abstract: Our globalizing world has become almost a small
village and everyone can access any information at any time.
Everyone lets each other know who does whatever in which place.
We can learn which social events occur in which place in the world.
From the perspective of education, the course notes that a lecturer use
in lessons in a university in any state of America can be examined by
a student studying in a city of Africa or the Far East. This dizzying
communication we have mentioned happened thanks to fast
developments in computer and internet technologies. While these
developments occur in the world, Turkey that has a very large young
population and whose electronic infrastructure rapidly improves has
also been affected by these developments. Nowadays, mobile devices
have become common and thus, it causes to increase data traffic in
social networks. This study was carried out on students in the
different age groups in Selcuk University Vocational School of
Technical Sciences, the Department of Computer Technology.
Students’ opinions about the use of internet and social media were
obtained. The features such as using the Internet and social media
skills, purposes, operating frequency, accessing facilities and tools,
social life and effects on vocational education and so forth were
explored. The positive effects and negative effects of both internet
and social media use on the students in this department and findings
are evaluated from different perspectives and results are obtained. In
addition, relations and differences were found out statistically.
Abstract: Employer branding is considered as a useful tool for
addressing the global-local problem facing complex organisations
that have operations scattered across the globe and face challenges of
dealing with the local environment alongside. Despite being an
established field of study within the Western developed world, there
is little empirical evidence concerning the relevance of employer
branding to global companies that operate in the under-developed
economies. This paper fills this gap by gaining rich insight into the
implementation of employer branding programs in a foreign
multinational operating in Pakistan dealing with the global-local
problem. The study is qualitative in nature and employs semistructured
and focus group interviews with senior/middle managers
and local frontline employees to deeply examine the phenomenon in
case organisation. Findings suggest that authenticity is required in
employer brands to enable them to respond to the local needs thereby
leading to the resolution of the global-local problem. However, the
role of signaling theory is key to the development of authentic
employer brands as it stresses on the need to establish an efficient and
effective signaling environment where in signals travel in both
directions (from signal designers to receivers and backwards) and
facilitate firms with the global-local problem. The paper also
identifies future avenues of research for the employer branding field.
Abstract: In this paper, we introduced a gradient-based inverse
solver to obtain the missing boundary conditions based on the
readings of internal thermocouples. The results show that the method
is very sensitive to measurement errors, and becomes unstable when
small time steps are used. The artificial neural networks are shown to
be capable of capturing the whole thermal history on the run-out
table, but are not very effective in restoring the detailed behavior of
the boundary conditions. Also, they behave poorly in nonlinear cases
and where the boundary condition profile is different.
GA and PSO are more effective in finding a detailed
representation of the time-varying boundary conditions, as well as in
nonlinear cases. However, their convergence takes longer. A
variation of the basic PSO, called CRPSO, showed the best
performance among the three versions. Also, PSO proved to be
effective in handling noisy data, especially when its performance
parameters were tuned. An increase in the self-confidence parameter
was also found to be effective, as it increased the global search
capabilities of the algorithm. RPSO was the most effective variation
in dealing with noise, closely followed by CRPSO. The latter
variation is recommended for inverse heat conduction problems, as it
combines the efficiency and effectiveness required by these
problems.
Abstract: Long Distance Truck Drivers (LDTDs) have been
found to be a high risk group in the spread of HIV/AIDS globally;
perhaps, due to their high Sexual Risk Behaviours (SRBs).
Interventions for reducing SRBs in trucking population have not been
fully exploited. A quasi-experimental control group pretest-posttest
design was used to assess the efficacy of psycho-education and
behavioural skills training in reducing SRBs among LDTDs. Sixteen
drivers rivers were randomly assigned into either experimental or
control groups using balloting technique. Questionnaire was used as
an instrument for data collection. Repeated measures t-test and
independent t-test were used to test hypotheses. Intervention had
significant effect on the SRBs among LDTDs at post-test (t{7}=
6.01, p
Abstract: Incineration of municipal solid waste (MSW) is one of
the key scopes in the global clean energy strategy. A computational
fluid dynamics (CFD) model was established in order to reveal these
features of the combustion process in a fixed porous bed of MSW.
Transporting equations and process rate equations of the waste bed
were modeled and set up to describe the incineration process,
according to the local thermal conditions and waste property
characters. Gas phase turbulence was modeled using k-ε turbulent
model and the particle phase was modeled using the kinetic theory of
granular flow. The heterogeneous reaction rates were determined
using Arrhenius eddy dissipation and the Arrhenius-diffusion
reaction rates. The effects of primary air flow rate and temperature in
the burning process of simulated MSW are investigated
experimentally and numerically. The simulation results in bed are
accordant with experimental data well. The model provides detailed
information on burning processes in the fixed bed, which is otherwise
very difficult to obtain by conventional experimental techniques.
Abstract: This paper describes an Action Research project
which was undertaken to inform professional practice in order to
develop a newly created Centre for Student Success in the specific
context of transnational medical and nursing education in the Middle
East. The objectives were to enhance the academic performance,
persistence, integration and personal and professional development of
a multinational study body, in particular in relation to pre-clinical
medical students, and to establish a comfortable, friendly and
student-driven environment within an Irish medical university
recently established in Bahrain. The outcomes of the project resulted
in the development of a specific student success ‘signature’ for this
particular transnational higher education context.
Abstract: The Algeria by its location offers a rich and diverse
vegetation. A large number of aromatic and medicinal plants grow
spontaneously. The interest in these plants has continued to grow in
recent years. Their particular properties due to the essential oil
fraction can be utilized to treat microbial infections. To this end, and
in the context of the valuation of the Algerian flora, we became
interested in the species of the family Lamiaceae which is one of the
most used as a global source of spices. The plant on which we have
based our choice is a species of sage "Salvia officinalis" from the
Isser localized region within the province of Boumerdes. This work
focuses on the study of the antimicrobial activity of essential oil
extracted from the leaves of Salvia officinalis. The extraction is
carried out by essential oil hydrodistillation and reveals a yield of
1.06℅. The study of the antimicrobial activity of the essential oil by
the method of at aromatogramme shown that Gram positive bacteria
are most susceptible (Staphylococcus aureus and Bacillus subtilis)
with a strong inhibition of growth. The yeast Candida albicans
fungus Aspergillus niger and have shown moderately sensitive.
Abstract: Most people today are aware that global climate
change is not just a scientific theory but also a fact with worldwide
consequences. Global climate change is due to rapid urbanization,
industrialization, high population growth and current vulnerability of
the climatic condition. Water is becoming scarce as a result of global
climate change. To mitigate the problem arising due to global climate
change and its drought effect, harvesting rainwater from green roofs,
an environmentally-friendly and versatile technology, is becoming
one of the best assessment criteria and gaining attention in Malaysia.
This paper addresses the sustainability of green roofs and examines
the quality of water harvested from green roofs in comparison to
rainwater. The factors that affect the quality of such water, taking
into account, for example, roofing materials, climatic conditions, the
frequency of rainfall frequency and the first flush. A green roof was
installed on the Humid Tropic Centre (HTC) is a place of the study
on monitoring program for urban Stormwater Management Manual
for Malaysia (MSMA), Eco-Hydrological Project in Kuala Lumpur,
and the rainwater was harvested and evaluated on the basis of four
parameters i.e., conductivity, dissolved oxygen (DO), pH and
temperature. These parameters were found to fall between Class I and
Class III of the Interim National Water Quality Standards (INWQS)
and the Water Quality Index (WQI). Some preliminary treatment
such as disinfection and filtration could likely to improve the value of
these parameters to class I. This review paper clearly indicates that
there is a need for more research to address other microbiological and
chemical quality parameters to ensure that the harvested water is
suitable for use potable water for domestic purposes. The change in
all physical, chemical and microbiological parameters with respect to
storage time will be a major focus of future studies in this field.
Abstract: The purpose of the present work was to develop an
innovative food product with nutritional properties as well as
appealing organoleptic qualities. The product, a jam, was prepared
with the beans’ cooking water combined with fresh apple or carrot,
without the addition of any conservatives. Three different jams were
produced: bean and carrot, bean and apple and bean, apple and
cinnamon. The developed products underwent a sensorial analysis
that revealed that the bean, apple and cinnamon jam was globally
better accepted. However, with this study, the consumers determined
that the bean and carrot jam had the most attractive color and the
bean and apple jam the better consistency. Additionally, it was
possible to analyze the jams for their chemical components, namely
fat, fiber, protein, sugars and antioxidant activity. The obtained
results showed that the bean and carrot jam had the highest lipid
content, while the bean, apple and cinnamon jam had the highest
fiber content, when compared to the other two jams. Regarding the
sugar content, both jams with apple revealed similar sugar values,
which were higher than the sugar content of the bean and carrot jam.
The antioxidant activity was on average 10 mg TE/g.
Abstract: Now in some countries of the world the cellular
market is on the point of saturation, in others - positive dynamics of
development kept on. The reasons for it are also different, but there
are united by their general susceptibility to innovation changes, if
they are really innovative. If to take as an example the cellular market
of Kazakhstan it is defined by the low percent of smart phones at
consumers, the low population density, undercapacity of the 3G
channel, and absence of universal access to the LTE technology that
limits dynamical growth of this branch. These moments are
aggravated by failures of starting commercial projects by private
companies which prevent to be implemented and widely adopted to a
new product among consumers. The object of the research is possible
integration of wireless and program technologies at which
introduction the idea can regenerate in an innovation. The analysis of
existing projects in the market and the possible union of the
technologies through a prism of theoretical bases of innovative
activity shows that efficiency of the company by development and
introduction of innovations is possible only thanks to strict
observance of all terms and conditions of the innovative process
which main term is profit. Despite that fact that on a global scale the
innovativeness issue of companies is very popular, there are no
researches about possibility of innovative breaks in the field of
wireless access to the Internet in the cellular market of Kazakhstan.
Abstract: MSMEs are regarded as the sunrise sector of the
Indian economy in view of its large potential for growth and likely
socio economic impact specifically on employment and income
generation. In today’s competitive business environment, global
competition forces companies to continuously seek ways of
improving their products and services. The pressure on organizations
to adapt to new technologies and external threats requires
resourcefulness, creativity and innovation. Market has become more
open, competitive and customers more demanding. Without
continuous technology innovation, no organization can ever remain
competitive. Innovations reflect a critical way in which organizations
respond to either technological or market challenges. The need of the
market is to deliver high quality products through continuous
changing in features in product, improve existing products, reduce
their cost, and improve employee skills, training, technology
infrastructure and financial policies. Therefore, the key factor of
organization’s ability to change is innovation. The study presents a
detailed review of literature on the role of technology innovation in
improving manufacturing performance of industries.
Abstract: Africa enjoys some of the best solar radiation levels in
the world averaging between 4-6 kWh/m2/day for most of the year
and the global economic and political conditions that tend to make
African countries more dependent on their own energy resources
have caused growing interest in renewable energy based
technologies. However to-date, implementation of modern Energy
Technologies in Africa is still very low especially the use of solar
conversion technologies. This paper presents literature review and
analysis relating to the techno-economic feasibility of solar
photovoltaic power generation in Africa. The literature is basically
classified into the following four main categories. Techno-economic
feasibility of solar photovoltaic power generation, design methods,
performance evaluations of various systems and policy of potential
future of technological development of photovoltaic (PV) in Africa
by exploring the impact of alternative policy instruments and
technology cost reductions on the financial viability of investing solar
photovoltaic in Africa.